Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂-reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thank to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.     

Sintering kinetics of α-Al2O3 powder

The sintering kinetics of α-Al₂O₃ powder are reviewed in this paper. The initial sintering of α-Al₂O₃ micropowder and α-Al₂O₃ nanopowder is all controlled by grain boundary diffusion. The sintering kinetics dominate up to a relative density of 0.77, where the coarsening kinetics dominate during further densification. Herring's scaling law can be used to predict the approximate sintering temperature of α-Al₂O₃ powder and demonstrates that if the particle size can be reduced to <20 nm, sintering below 1000°C may be possible. ©     

The functionalities of Pt/γ-Al2O3 catalysts in simultaneous HDS and HDA reactions

A Pt/γ-Al₂O₃ catalyst was tested in simultaneous hydrodesulfurization (HDS) of dibenzothiophene and hydrodearomatization (HDA) of naphthalene reactions. Samples of it were subjected to different pretreatments: reduction, reduction–sulfidation, sulfidation with pure H₂S and non-activation. The reduced catalyst presented the best performance, even comparable to that of Co(Ni)Mo catalysts. All catalyst samples were selective to the HDS reaction over HDA, and to the direct desulfurization pathway of dibenzothiophene HDS over the hydrogenation reaction pathway of HDS. The effect of H₂S partial pressure on the functionalities of the reduced Pt/γ-Al₂O₃ catalyst was studied. The results showed that an increase in H₂S partial pressure does not cause poisoning, but an inhibition effect, without changing the catalyst selectivity. Accordingly, the activity trends were ascribed to adsorption differences between the different reactive molecules over the same catalytic active site. TPR characterization along with a thermodynamics analysis showed that the active phase of reduced Pt/γ-Al₂O₃ is constituted by Pt⁰ particles. However, presulfidation of the catalyst leads to a mixture of PtS and Pt⁰ which has a negative effect on the catalytic performance without changing catalyst functionalities.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Densification ability of combustion-derived Al2O3 powders

Nanocrystalline Al₂O₃ powders containing different amounts of MgO (0.1–5.0 mol%) or added boehmite (AlOOH) have been synthesized by combustion synthesis from aluminium nitrate and magnesium nitrate, using urea or sucrose as fuels. The as synthesized alumina powders were deagglomerated, compacted by dry pressing and sintered at 1625 °C for 2 h. For comparison purposes, a commercial high purity α-Al₂O₃ powder (ACC) was also processed following the same route. The sintered materials were characterized for bulk density (BD), apparent porosity (AP), and water absorption (WA) capacity, microstructure using SEM, and XRD phase composition. In comparison to boehmite, the MgO had a considerable effect on the densification behaviour of combustion-synthesized powder.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

Effect of CO2 in the feed stream on the deactivation of Co/γ-Al2O3 Fischer–Tropsch catalyst

The influence of CO₂ on the deactivation of Co/γ-Al₂O₃ Fischer–Tropsch (FT) catalyst in CO hydrogenation has been investigated. The presence of CO₂ in the feed stream reveals a negative effect on catalyst stability and in the formation of heavy hydrocarbons. The CO₂ acts as a mild oxidizing agent on cobalt metal during Fischer–Tropsch synthesis. During FT synthesis on Co/γ-Al₂O₃ of 70 h, the CO conversion and C₅₊ selectivity in the presence of CO₂ decreased more significantly than in the absence of CO₂. CO₂ is found to be responsible for the partial oxidation of surface cobalt metal at FT synthesis environment with the co-existence of generated water.     

Selective synthesis of mixed alcohols from syngas over catalyst Fe2O3/Al2O3 in slurry reactor

The Fe₂O₃/Al₂O₃ catalyst was studied to selectively synthesize mixed alcohols from syngas in a continuously stirred slurry reactor with the oxygenated solvent Polyethylene Glycol-400 (PEG-400). The selectivity of mixed alcohols in the products reached as high as 95 wt.% and the C₂₊ alcohols (mainly ethanol) was more than 40 wt.% in the total alcohol products at the reaction conditions of 250 °C, 3.0 MPa, H₂/CO = 2 and space velocity = 360 ml/g_cat h. The hydrogen temperature programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) measurements of the catalyst confirmed that the FeO phase was responsible for the high selectivity to mixed alcohols in the process. And the oxygenated solvent PEG-400 was also necessary for the selective synthesis of mixed alcohols in the reaction system.     

Effect of SO2 on the catalytic activity of Ga2O3–Al2O3 for the selective reduction of NO with propene in the presence of oxygen

The effect of coexisting SO₂ on the catalytic activity of Ga₂O₃–Al₂O₃ prepared by impregnation, coprecipitation and sol–gel method for NO reduction by propene in the presence of oxygen was studied. Although the activity of Al₂O₃ and Ga₂O₃–Al₂O₃ prepared by impregnation (Ga₂O₃/Al₂O₃(I)) and coprecipitation (Ga₂O₃–Al₂O₃(CP)) was depressed considerably by the presence of SO₂, NO conversion on Ga₂O₃–Al₂O₃ prepared by sol–gel method (Ga₂O₃–Al₂O₃(S)) was not decreased but increased slightly by SO₂ at temperatures below 723 K. From catalyst characterization, SO₂ treatment was found to cause two important effects on the surface properties: one is the creation of Brønsted acid sites on which propene activation is promoted (positive effect), and the other is the poisoning of NO_x adsorption sites on which NO reduction proceeds (negative effect). It was presumed that the influence of SO₂ treatment on the catalytic activity is strongly related to the balance between the negative and positive. The activity enhancement of Ga₂O₃–Al₂O₃(S) by SO₂ was accounted for by the following consideration: (1) increase of the propene activation ability by SO₂, (2) incomplete inhibition of NO_x adsorption sites by SO₂.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Development of input output relationships for self-healing Al2O3/SiC ceramic composites with Y2O3 additive using design of experiments

Al₂O₃/SiC ceramic composites with Y₂O₃ as an additive, was synthesized using the Taguchi method of design of experiments, so as to develop statistically sound input output relationships. The proportion of SiC was varied from 12 to 21 vol.% whereas that of Y₂O₃ was varied from 2.5 to 4 vol.%. The composites were sintered at 1500 °C for a soaking time period of 12 h in an air atmosphere. Cracks were induced on the composite surface using a Vickers indenter with a load varying between 20 and 40 kg. Fractographical analyses have been carried out using optical and/or scanning electron microscopy to investigate the surface crack propagation behavior. Thermal aging at 1300 °C in the time range of 0.5-12.5 h was applied to find optimal conditions for healing of the pre-cracked samples. The output parameters such as crack length, healed crack length, hardness and fracture toughness of the samples were correlated with appropriate inputs such as contents of SiC and Y₂O₃, crack-healing temperature, healing time, compaction pressure, indentation load using statistical analysis. Further, the extent of influence, exerted by pertinent input parameters on output parameters, was also identified.     

Matrix–filler interactions in polysilazane-derived ceramics with Al2O3 and ZrO2 fillers

Interactions between a poly(vinyl)silazane and Al₂O₃ or Y₂O₃-stabilised ZrO₂ fillers were studied during the fabrication of polysilazane-derived bulk ceramics in order to investigate the influence of oxide fillers on resulting properties. Specimens were produced by coating of the filler powders with the polysilazane, warm-pressing of the resulting composite powders, and pyrolytic conversion in flowing N₂ at various temperatures between 1000 °C and 1400 °C. Significant differences in densification were observed, depending on the filler used. Reactions between the polysilazane-derived matrix and Al₂O₃ or ZrO₂ at temperatures ≥1300 °C resulted in the formation of Si₅AlON₇ or ZrSiO₄, respectively. Reactivity in the polysilazane-derived component was a result of SiO₂ contamination caused primarily by adsorbed species on the filler particle surface. Knowledge of polysilazane/filler interface processes is found to be decisive for the prediction of properties such as shrinkage and porosity, which heavily influence performance of a material.     

Dynamic corrosion of Al2O3-ZrO2-SiO2 and Cr2O3-containing refractories by molten frits. Part II: Microstructural study

In this work results on dynamic corrosion studies of fused cast Al₂O₃-SiO₂-ZrO₂ and isostatically pressed and sintered Cr₂O₃-based refractories by two crystalline (transparent) frits are described. Experiments have been performed using the “Merry Go Round” test at ≅1500 °C.Microstructural and mineralogical analyses of selected areas from the corroded regions of the studied refractories were performed by reflected light optical microscopy and scanning electron microscopy with analysis by X-ray dispersive energy.Significant differences between the corrosion mechanisms acting in the two types of materials were found. In the fused cast Al₂O₃-SiO₂-ZrO₂ specimens corrosion took place by the dissolution of alumina and zirconia in the frit and in the glass formed by the reaction between the frit and the refractory. In the Cr₂O₃-based materials the corrosion process was controlled by the capillar penetration of the molten frit through the open pores. The reaction between the ZnO from the frits and Cr₂O₃ led to the formation of spinel (ZnCr₂O₄), a high-melting point bonding phase that retarded the frit penetration. Results are discussed using the relevant phase equilibrium diagrams.     

UV laser microprocessing and post chemical etching on ultrathin Al2O3 ceramic substrate

In this study, an Nd:YVO₄ UV laser was used for microprocessing ultrathin (125 μm) ceramic plates for use as a multi-layer microchip substrate. The effects of the UV laser microprocessing parameters, including laser power density, frequency, laser scanning speed, and pass delay on microprocessing accuracy and quality (kerf width and arithmetic average roughness R_a on the kerf sidewall) were investigated by means of a 4 × 4 orthogonal design. The key processing parameters were determined and optimized for small kerf width and minimal R_a of the kerf sidewall while retaining high production efficiency. Subsequent chemical etching of the laser processed areas was performed to reduce the kerf surface and kerf sidewall roughness by removing debris and the thin recast layer for the required size precision and post gilding treatment. The results showed that a clean surface and crack-free kerf sidewall with roughness R_a of 0.16 μm could be achieved by laser microprocessing and chemical etching.     

The effect of sodium on the catalytic activity of ZnO–Al2O3/ZSM-5 and SnO–Al2O3/ZSM-5 for the transesterification of vegetable oil with methanol

In order to elucidate the effect of sodium on the activity of ZSM-5 supported metal oxides catalysts (ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5) for the transesterification of soybean oil with methanol, ZSM-5 supported metal oxides were prepared with and without sodium hydroxide by impregnation. The metal compositions of the ZSM-5 supported metal oxide catalysts and the metal concentrations dissolved from the catalysts to the methylester phase were measured by SEM-EDS and inductive coupled plasma spectroscopy, respectively. The catalytic activity of ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5 containing sodium did not originate from surface metal oxides sites, but from surface sodium sites or dissolved sodium leached from the catalyst surface.     

Influence of Ru segregation on the activity of Ru–Co/γ-Al2O3 during FT synthesis: A comparison with that of Ru–Co/SiO2 catalysts

γ-Al₂O₃ and SiO₂ supported Co catalysts, with varying amounts of Ru, were prepared and evaluated for Fischer–Tropsch synthesis (FTS). The composition of Ru for optimum activity was found to be support-dependent. The reducible Co₃O₄ was high in the region of 0–1.64 wt.% of Ru in Co/SiO₂ catalysts. Co/γ-Al₂O₃ displayed a maximum for reducible Co species at 0.42 wt.% Ru. Segregation of Ru occurred beyond this composition decreasing the extent of reduction. Co/γ-Al₂O₃ catalysts showed lower activity and olefin selectivity, in spite of higher Co dispersion, than Co/SiO₂ catalysts. The catalytic performance depends on the amount of reducible Co species, which again depends upon the optimum content of Ru.     

Conditioning of Rh/α-Al2O3 catalysts for H2 production via CH4 partial oxidation at high space velocity

Experimental evidence and literature indications suggest that the process of methane partial oxidation over Rh catalysts is structure sensitive. Crystal phases and Rh cluster size are thus expected to affect the final catalytic performance. In this work, it is observed that outstanding performances are obtained when the as-prepared catalysts are conditioned through repeated runs at increasing temperature and O₂/CH₄ = 0.56. Catalysts slowly activate, that is CH₄ conversion and synthesis gas selectivity progressively grow with time on stream. On the basis of TPO and CH₄ decomposition measurements, this phenomenon is herein explained as the result of a surface reconstruction driven by the repeated exposition to the reaction at high temperature; it is thought that such reconstruction tends to eliminate defect sites and disfavors C-deposition reactions (extremely fast over steps and kinks). Conditioning with O₂-enriched feed streams makes conditioning faster, since the accumulation of surface C-species is suppressed; however, the catalyst is eventually less active than a catalyst conditioned with standard feed mixtures. As an alternative, accumulation of carbon can be suppressed and surface reconstruction proceeds faster if the catalyst is directly exposed to the reaction at high temperature for several hours.