HOW TO INCREASE THE DRYER EFFICIENCY - LOSS PREVENTION ON A PAPER MACHINE

In order to reduce superfluous energy consumption, the dryer section of an open paper machine was investigated experimentally. The recorded data covered the energy - and mass balances of both the individual drums and the whole dryer section, the state characteristics of the dryer air and some characteristics of the product. In the constant rate period of evaporation the specific heat consumption shows the minimum between 100 1050C dryer surface temperature while the specific evaporation performance is in direct proportion to it. The extent of the increase in energy consumption and of the decrease in evaporation performance below the critical value of moisture content is also demonstrated. Additional possibilities of energy saving exist mainly in aeration and in the more efficient operation of the presses. Some of the results are the characteristics of the investigated machine. It is believed, however, that the results referring to the effect of dryer surface temperature and moisture content are of a general validity and can be applied to other systems as well.     

Energy system diagnosis of paper-drying process,Part 1: Energy performance assessment

Paper drying is a highly energy-intensive and complicated multivariate process. The dryer section plays an important role in the energy consumption of a paper machine, especially of thermal energy. A comprehensive method for assessing the energy performance of the dryer section was investigated in this study to improve energy efficiency. This method was divided into three component processes: energy and evaporation load audit, field test and observation, and energy flow analysis and energy efficiency estimation. In a case study, we found that the method could, in addition to analyzing the key factors that restrict drying efficiency, also depict the details of energy consumption clearly. At the same time, several significant energy-saving measures were suggested to improve the energy efficiency of the paper-drying process.     

Process Parameters Optimization for Energy Saving in Paper Machine Dryer Section

Due to high energy consumption in the Chinese paper industry, this study considers higher-energy efficiency for the multicylinder dryer section of paper machines. A common situation in the Chinese paper industry is that energy is consumed in extensive mode. In order to improve the energy efficiency of the paper machine dryer section, deeper analysis and optimization of process parameters are necessary.

A NLP optimization method is developed for integration of steam system and air system to reduce the steam consumption and decrease the loads of centrifugal blowers in the multicylinder dryer section of a paper machine. Equality constraints of the optimization model are extracted from different process modules based on material and energy balance. Inequality constraints are from the production capacity, operating condition, etc. Two illustrative examples are presented in this paper. The results show that the optimization model is adaptive and convenient for application. For a newsprint machine, less dry air and steam are used and the energy consumption can be reduced by about 8% in the dryer section. Applied on a linerboard machine which has surface sizing, the method can reduce the energy consumption by 5.6%.     

Effect of operating parameters on the drying performance of multicylinder paper machine dryer section

The drying performance of multicylinder dryer section in a paper machine was investigated under various operating parameters: Inlet paper solid content (48–50%), inlet paper temperature (45–50°C), supply air temperature (100–90°C), and exhaust air humidity (75–85?g H₂O/kg dry air). The variation in environmental conditions was also considered. In this study, an improved static model was utilized to study the influence of these operating parameters on paper drying. The model was constructed using sequential modeling approach based on the drying techniques of multicylinder dryer section of a paper machine. The calculated paper solid content leaving each paper drying module and energy use is in agreement with the measured results. The simulation results showed that higher paper solid content and temperature entering the dryer section, lower supply air temperature, and higher exhaust air humidity were favorable for drying performance within the studied range of these parameters.     

Steady-State Modeling of Multi-Cylinder Dryers in a Corrugating Paper Machine

In this study, a steady-state model was developed to describe the paper drying process and to analyze pocket dryer conditions for a multi-cylinder fluting paper machine in Iran's Mazandaran Wood and Paper Industries. The machine has 35 cylinders grouped in three drying groups and the cylinders are heated from the inside by steam. The model is based on the mass and energy balance relationships written for fiber, air, and water in the drying section. In this research, the heat of sorption and its variations with paper temperature and humidity changes have been taken into account. Temperature and moisture variation of the paper web and cylinder surface temperature in the machine direction were predicted by the proposed model. Also, temperature and humidity of air in the drying pockets and hood exhaust were estimated by the proposed model. Moreover, the model can predict the evaporation rate and specific drying rate with sufficient accuracy in comparison with the TAPPI standard. Finally, the main modeling parameters were compared with the available operating data and the effectiveness of the developed model was verified through validations.     

Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and without a Cyclone

The objective of the present work is to find the possibility of reducing the high initial moisture content of wet paddy using a small-scale, low-cost pneumatic conveying dryer that can be provided for each farming household. The dryer without a cyclone equipped at the exit of the dryer is studied and the data obtained from this system is compared with those obtained previously from the dryer with a cyclone. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, and drying air temperature from 35 to 70°C. From the experimental results it is found that the drying process with and without a cyclone are able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. For the same experimental conditions, the cyclone-equipped dryer gives around 1% higher decrease of moisture content, 2°C higher average surface temperature of paddy, 3-4% higher average percentage of head rice yield, and 2 kg/h higher average evaporation rate. However, the energy consumption per evaporated mass of water is 20-30% lower than the non-cyclone-equipped dryer.     

Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and without a Cyclone

The objective of the present work is to find the possibility of reducing the high initial moisture content of wet paddy using a small-scale, low-cost pneumatic conveying dryer that can be provided for each farming household. The dryer without a cyclone equipped at the exit of the dryer is studied and the data obtained from this system is compared with those obtained previously from the dryer with a cyclone. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, and drying air temperature from 35 to 70°C. From the experimental results it is found that the drying process with and without a cyclone are able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. For the same experimental conditions, the cyclone-equipped dryer gives around 1% higher decrease of moisture content, 2°C higher average surface temperature of paddy, 3–4% higher average percentage of head rice yield, and 2 kg/h higher average evaporation rate. However, the energy consumption per evaporated mass of water is 20–30% lower than the non-cyclone-equipped dryer.     

Performance of Two Industrial Dryers for Fish Feed

Performance and energy efficiency of two types of dryers for fish feed are compared. The first dryer was a belt dryer located at a fish feed production facility in Norway. The second dryer was a counterflow multideck dryer at a fish feed production facility in Chile. In both dryers there was only a slight decrease in drying rate over the dryer. Product samples showed a standard deviation of 0.45% on an average moisture content of 10.2% (wb) for the belt dryer and 0.49% on an average of 8.6% (wb) for the counterflow dryer. Mass and heat balances showed good accuracy. In order to compare the energy use of both dryers, normalized energy consumption and efficiency were calculated for equal feed and air inlet temperatures using two methods: the primary energy method and the energy difference method. The average normalized specific energy consumption for the belt dryer was 3,386 kJ/kg water evaporation (primary energy method) and 2,970 kJ/kg (energy difference method), with efficiencies of 56 and 64%, respectively. For the counterflow dryer the average specific energy consumption was 2,893 kJ/kg (primary energy method) and 2,393 kJ/kg (energy difference method), with efficiencies of 70 and 85%, respectively.     

Development and Thermal Modeling of a New Construction Biomass Dryer

A new dryer construction has been developed for drying biomass basic materials for energy purposes (straw, sawdust, and other light granular materials). As a result of its simple design, the machine is perfectly suitable for reducing moisture by heat transfer. Compared to the machine types applied thus far, this new construction provides a better ratio of dryer floor space and drying distance and, as a result, a longer drying time. A differential equation system for convection drying was applied for the thermal modeling of the equipment; the mathematical model produced on the basis there of is suitable for examining the heat and mass transfer processes within the dryer. In the course of experimental measurements performed in an industrial size apparatus, the temperature and moisture content of the drying gas were recorded with the initial and final moisture content and surface temperature of the product. The measured values were compared to the results of calculations using the mathematical model.     

Bagasse saving and water recovery in cogeneration system using superheated steam dryer

The cogeneration system in sugar factory uses bagasse with high moisture content as the fuel for the boiler, which results in low boiler efficiency. The system also produces superheated steam, which is extracted from the turbine, and mixed with cooling water to produce saturated steam required by the evaporation system. The potential use superheated steam to reduce bagasse moisture content is ignored in the standard practice of the sugar factory. In this article, an investigation is made into the improvement of the cogeneration system by using superheated steam dryer to reduce the moisture content of bagasse. Mathematical models are developed for the typical system without superheated steam dryer and the improved system with superheated steam dryer. They are then used to compare the performances of both systems. It is found that, under the condition that the required steam flow rate for the evaporation process and the power output are the same, the improved system requires less bagasse consumption, and has larger energy utilization factor. In addition, water that would be lost with flue gases in the typical system is recovered in the improved system.     

An Evaluation of Factors Influencing the Energy-Efficient Operation of Well-Mixed Fluidized Bed Dryers

This article describes the results of calculations of specific energy consumption, E_s, performed on a well-mixed fluidized bed dryer simulator. Exhaust air temperature-humidity loci required to yield a specified outlet moisture content were also determined. Most of the calculations related to solids whose drying rate was gas-film controlled. Six model drying curves were employed to examine the effects of drying rate and hygroscopicity in addition to the normal operating parameters. The results indicated that E_s was highest for slow-drying hygroscopic solids and lowest for fast-drying, non-hygroscopic solids. Specific energy consumption increased with decreasing bed temperature and outlet moisture content and with increasing heat loss but was independent of solids loading and airflow rate. For both the aforementioned solids and a much slower drying material (wheat), there was close agreement between the zero heat loss data and a single theoretical curve approximating the performance of an ideal adiabatic dryer. Distinct differences between the behavior of well-mixed and plug flow fluidized bed dryers are reported.     

STUDY OF LONGAN FLESH DRYING

The objectives of this research were to study the characteristics and quality of longan flesh drying and to develop the models for drying simulations. Finite difference method was applied to solve the drying kinetic equations. Three alternative diffusion models were developed by modifying the Arrhenius factor and/or the energy of activation as a function of moisture content. The results using effective diffusion coefficients obtained from each model were compared. Desorption isotherms were also developed by fitting experimental results to various well-known models. The development and simulation of mathematical drying model of a cabinet dryer were also studied. The effects of drying air temperature and specific air flow rate on specific energy consumption were described. Additionally, the effect of drying air temperature on product quality was investigated by experiment.     

STUDY OF LONGAN FLESH DRYING

The objectives of this research were to study the characteristics and quality of longan flesh drying and to develop the models for drying simulations. Finite difference method was applied to solve the drying kinetic equations. Three alternative diffusion models were developed by modifying the Arrhenius factor and/or the energy of activation as a function of moisture content. The results using effective diffusion coefficients obtained from each model were compared. Desorption isotherms were also developed by fitting experimental results to various well-known models. The development and simulation of mathematical drying model of a cabinet dryer were also studied. The effects of drying air temperature and specific air flow rate on specific energy consumption were described. Additionally, the effect of drying air temperature on product quality was investigated by experiment.     

THE DEPENDENCE OF PAPER MACHINE DRYING DRYING CHARACTERISTIC ON THE MACHINE GEOMETRY

The effect of the dryer cylinder diameter on the dryer specific evaporation rate is examined theoretically. It is observed that, in the range of cylinder diameters applicable in practice, the dryer specific evaporation rate is nearly independent of the selected cylinder diameter when the dryer geometry remains unchanged. In practice, however, the dryer geometries have changed slightly according to the cylinder diameter.

TO clarify the effects of the various component factors pertaining to the dryer geometry, this paper presents a drying characteristic, i.e.. a curve showing the dependence of the drying rate on the condensing steam temperature. The drying characteristic is given in the form of a nomogram to facilitate the evaluation of the effect of the ratio between the free draw length and the cylinder diameter, and the wrapping angle, to the dryer specific evaporation rate. Further, by means of an example, the specific evaporation rates obtainable for machine geometries currently used by various machine manufacturers are compared.     

Bibliography of Literature on Fundamentals and Applications of Vibration in Particle Processing

This article describes the results of calculations of specific energy consumption, E _s , performed on a well-mixed fluidized bed dryer simulator. Exhaust air temperature–humidity loci required to yield a specified outlet moisture content were also determined. Most of the calculations related to solids whose drying rate was gas-film controlled. Six model drying curves were employed to examine the effects of drying rate and hygroscopicity in addition to the normal operating parameters. The results indicated that E _s was highest for slow-drying hygroscopic solids and lowest for fast-drying, non-hygroscopic solids. Specific energy consumption increased with decreasing bed temperature and outlet moisture content and with increasing heat loss but was independent of solids loading and airflow rate. For both the aforementioned solids and a much slower drying material (wheat), there was close agreement between the zero heat loss data and a single theoretical curve approximating the performance of an ideal adiabatic dryer. Distinct differences between the behavior of well-mixed and plug flow fluidized bed dryers are reported.     

Saffron Drying with a Heat Pump–Assisted Hybrid Photovoltaic–Thermal Solar Dryer

Saffron is the most expensive spice and Iran is the largest producer of this crop in the world. Saffron quality is profoundly affected by the drying method. Recent research has shown that hybrid photovoltaic–thermal solar power systems are more efficient in comparison with individual photovoltaic and thermal systems. In addition, heat pump dryers are highly energy efficient. Furthermore, they are suitable for heat-sensitive crops such as saffron. Therefore, in the present study, the performance of a hybrid photovoltaic–thermal solar dryer equipped with a heat pump system was considered for saffron drying, in order to obtain a high-quality product and reduce fossil fuel consumption. The effect of air mass flow rate at three levels (0.008, 0.012, and 0.016 kg/s), drying air temperature at three levels (40, 50, and 60°C), and two different dryer modes (with and without the heat pump unit) on the operating parameters of the dryer was investigated. The results of the investigation showed that total drying time and energy consumption decreased as air flow rate and drying air temperature increased. Applying a heat pump with the dryer led to a reduction in the drying time and energy consumption and an increase in electrical efficiency of the solar collector. The average total energy consumption was reduced by 33% when the dryer was equipped with a heat pump. Maximum values for electrical and thermal efficiency of the solar collector were found to be 10.8 and 28%, respectively. A maximum dryer efficiency of 72% and maximum specific moisture extraction rate (SMER) of 1.16 were obtained at an air flow rate of 0.016 kg/s and air temperature of 60°C when using the heat pump.     

Innovative Steam Drying of Empty Fruit Bunch with High Energy Efficiency

Empty fruit bunch (EFB) is one of the solid wastes from crude palm oil mills and has the lowest value for utilization compared to other solid wastes. To achieve an efficient utilization of EFB, drying is considered the first crucial process due to the high moisture content of EFB. In this study, EFB drying based on exergy recovery is proposed to achieve high energy efficiency. A fluidized bed is adopted as the main dryer. The proposed model is evaluated in terms of energy efficiency, especially regarding the influence of target moisture content and fluidization velocity. Up to 92% of the energy involved in the drying process can be recirculated. The total energy consumption for drying decreases as the target moisture content decreases, though there is no significant impact of fluidization velocity to total energy consumption. In addition, the required total length of the heat transfer tubes immersed inside the fluidized bed dryer is calculated because it relates to fluidization performance and economic issues. Lower target moisture content results in a longer heat transfer tube, and higher fluidization velocity leads to a shorter heat transfer tube.     

THE DEPENDENCE OF PAPER MACHINE DRYING DRYING CHARACTERISTIC ON THE MACHINE GEOMETRY

ABSTRACT

The effect of the dryer cylinder diameter on the dryer specific evaporation rate is examined theoretically. It is observed that, in the range of cylinder diameters applicable in practice, the dryer specific evaporation rate is nearly independent of the selected cylinder diameter when the dryer geometry remains unchanged. In practice, however, the dryer geometries have changed slightly according to the cylinder diameter.

TO clarify the effects of the various component factors pertaining to the dryer geometry, this paper presents a drying characteristic, i.e.. a curve showing the dependence of the drying rate on the condensing steam temperature. The drying characteristic is given in the form of a nomogram to facilitate the evaluation of the effect of the ratio between the free draw length and the cylinder diameter, and the wrapping angle, to the dryer specific evaporation rate. Further, by means of an example, the specific evaporation rates obtainable for machine geometries currently used by various machine manufacturers are compared.     

Dynamic Analysis of Drying Energy Consumption

A concept of instantaneous drying and energy efficiencies has been applied to analyze energy consumption in a through-circulation conveyor dryer and a batch fluid bed dryer for synthetic rubber. It is shown that the energy performance of the conveyor dryer can be improved by leveling of the moisture content distribution across the material layer by mechanical agitation, and sectioning of the air plenum in order to reduce inlet air temperature in the last two sections of the dryer. It is also shown that drying of a synthetic rubber in the fluid bed dryer is more energy-efficient than in the conveyor dryer, especially in the constant-rate period. Thus, the largest energy savings could be obtained in a two-stage dryer comprised of the plug-flow fluid bed dryer, and the belt conveyor dryer for removal of the bulk and residual water, respectively.     

Prediction of Moisture Content Evolution in a Grain Batch Dryer Based on On–line Temperature Measurements

ABSTRACT

The time evolution of the moisture content in a grain batch fluidized bed dryer is estimated by means of an on–line non–linear estimator (Marquardt–Levenberg algorithm). The inputs to the estimation algorithm are on–line temperature measurements and the output is the surface moisture content. The surface moisture content is used for predicting the grain moisture content through the solution of a single ordinary differential equation that combines the moisture and energy balances over the dryer. In this way the drying curves are obtained through incorporating in a very simple model easily obtainable physical information of the process.