Porous Silicon Nitride Ceramics Prepared by Reduction–Nitridation of Silica

A new method for preparing porous silicon nitride ceramics with high porosity had been developed by carbothermal reduction of die-pressed green bodies composed of silicon dioxide, carbon, sintering additives, and seeds. The resultant porous silicon nitride ceramics showed fine microstructure and uniform pore structure. The influence of SiO₂ particle size and sintering process (sintering temperature and retaining time) on the microstructure of sintering bodies was analyzed. X-ray diffractometry demonstrated the formation of single-phase β-Si₃N₄ via the reaction between silicon dioxide and carbon at high temperature. SEM analysis showed that pores were formed by the banding up of rod-like β-Si₃N₄ grains. Porous Si₃N₄ ceramics with a porosity of 70–75%, and a strength of 5–8 MPa, were obtained.     

Effect of β-Seed Addition on the Microstructural Evolution of Silicon Nitride Ceramics

When a small amount of β-Si₃N₄ seed particles is added during the preparation of Si₃N₄ ceramics, a bimodal microstructure is obtained by sintering at 1760°C. When the specimen is further heat-treated at 1900°C to enhance the bimodal characteristic, the growth of large β grains is limited. The addition of a controlled amount of β seeds of uniform and large size is suggested to obtain the intended bimodal microstructure of Si₃N₄ ceramics.     

Effect of Porosity and Microstructure on the Strength of Si3N4: Designed Microstructure for High Strength, High Thermal Shock Resistance, and Facile Machining

The flexural strength of porous Si₃N₄ ceramics with a variety of microstructures and porosities were evaluated, and the effect of microstructure on the flexural strength was investigated to obtain machinable Si₃N₄ ceramics having both high strength and high thermal shock resistance. Porous Si₃N₄ having three types of microstructure, consisting of (1) only spherical grains, (2) combinations of spherical and columnar grains, and (3) only columnar β-grains connected randomly in three dimensions, were readied as specimens. Their mean pore diameters and porosities were 0.2 to 0.3 μm and 8% to 59%, respectively. The flexural strength of the porous Si3N4 (3) was much larger than that of the porous Si3N4 having the other microstructures, and the maximum flexural strength was 455 MPa at a porosity of 38.3%. The thermal shock resistance (ΔT), which was determined by a water quench test, of porous Si₃N₄ with such microstructure and a porosity of 50% was 980 K. All of the porous Si₃N₄ (3) was easily machined with cemented carbide drills.     

Microstructure in Silicon Nitride Containing β-Phase Seeding: III, Grain Growth and Coalescence

The mechanical properties of Si₃N₄ materials depend mainly on the microstructure, which originates during the densification process. The microscopic evidence indicates that β-Si₃N₄ seeds incorporated in the starting powders play an important role in microstructural development, especially in the heterogeneous grain growth of β-Si₃N₄ grains during sintering. The growth of β-grains is initiated from the β-seeds, resulting in a core/shell microstructure. The presence of Moiré fringes and dislocations is attributed to misfit strain and compositional differences between the core and the shell. Coalescence can occur at the final stage of sintering.     

Pressureless Sintering of α-Si3N4 Porous Ceramics Using a H3PO4 Pore-Forming Agent

A new method for preparing high bending strength porous silicon nitride (Si₃N₄) ceramics with controlled porosity has been developed by using pressureless sintering techniques and phosphoric acid (H₃PO₄) as the pore-forming agent. The fabrication process is described in detail and the sintering mechanism of porous ceramics is analyzed by the X-ray diffraction method and thermal analysis. The microstructure and mechanical properties of the porous Si₃N₄ ceramics are investigated, as a function of the content of H₃PO₄. The resultant high porous Si₃N₄ ceramics sintered at 1000°–1200°C show a fine porous structure and a relative high bending strength. The porous structure is caused mainly by the volatilization of the H₃PO₄ and by the continous reaction of SiP₂O₇ binder, which could bond on to the Si₃N₄ grains. Porous Si₃N₄ ceramics with a porosity of 42%–63%, the bending strength of 50–120 MPa are obtained.     

Influence of Phase Formation on Dielectric Properties of Si3N4 Ceramics

The influence of phase formation on the dielectric properties of silicon nitride (Si₃N₄) ceramics, which were produced by pressureless sintering with additives in MgO–Al₂O₃–SiO₂ system, was investigated. It seems that the difference in the dielectric properties of Si₃N₄ ceramics sintered at different temperatures was mainly due to the difference of the relative content of α-Si₃N₄, β-Si₃N₄, and the intermediate product (Si₂N₂O) in the samples. Compared with α-Si₃N₄ and Si₂N₂O, β-Si₃N₄ is believed to be a major factor influencing the dielectric constant. The high-dielectric constant of β-Si₃N₄ could be attributed to the ionic relaxation polarization.     

Effect of α to β (β') Phase Transition on the Sintering of Silicon Nitride Ceramics

By using α-Si₃N₄ and β-Si₃N₄ starting powders with similar particle size and distribution, the effect of α-β (β') phase transition on densification and microstructure is investigated during the liquid-phase sintering of 82Si₃N₄·9Al₂O₃·9Y₂O₃ (wt%) and 80Si₃N₄·13Al₂O₃·5AIN·5AIN·2Y₂O₃. When α-Si₃N₄ powder is used, the grains become elongated, apparently hindering the densification process. Hence, the phase transition does not enhance the densification.     

New Strategies for Preparing NanoSized Silicon Nitride Ceramics

We report the preparation of nanosized silicon nitride (Si₃N₄) ceramics via high-energy mechanical milling and subsequent spark plasma sintering. A starting powder mixture consisting of ultrafine β-Si₃N₄ and sintering additives of 5-mol% Y₂O₃ and 2-mol% Al₂O₃ was prepared by high-energy mechanical milling. After milling, the powder mixture was mostly transformed into a non-equilibrium amorphous phase containing a large quantity of well-dispersed nanocrystalline β-Si₃N₄ particles. This powder precursor was then consolidated by spark plasma sintering at a temperature as low as 1600°C for 5 min at a heating rate of 300°C/min. The fully densified sample consisted of homogeneous nano-Si₃N₄ grains with an average diameter of about 70 nm, which led to noticeable high-temperature ductility and elevated hardness.     

Fabrication of Hard and Strong α/β-Si3N4 Composites With MgSiN2 as Addivitives

α/β-Si₃N₄ composites with various α/β phase ratios were prepared by hot pressing at 1600°–1650°C with MgSiN₂ as sintering additives. An excellent combination of mechanical properties (Vickers indentation hardness of 23.1 GPa, fracture strength of about 1000MPa, and toughness of 6.3 MPa·m^1/2) could be obtained. Compared with conventional Si₃N₄-based ceramics, this new material has obvious advantages. It is as hard as typical in-situ-reinforced α-Sialon, but much stronger than the latter (700 MPa). It has comparable fracture strength and toughness, but is much harder than β-Si₃N₄ ceramics (16 GPa). The microstructures and mechanical properties can be tailored by choosing the additive and controlling the heating schedule.     

Thermal Conductivity of Gas-Pressure-Sintered Silicon Nitride

Si₃N₄ with high thermal conductivity (120 W/(m^.K)) was developed by promoting grain growth and selecting a suitable additive system in terms of composition and amount. β-Si₃N₄ doped with Y₂O₃-Nd₂O₃ (YN system) or Y₂O₃-A1₂O₃ (YA system) was sintered at 1700°-2000°C. Thermal conductivity increased with increased sintering temperature because of decreased two-grain junctions, as a result of grain growth. The effect of the additive amount on thermal conductivity with the YN system was rather small because increased additive formed multigrain junctions. On the other hand, with the YA system, thermal conductivity considerably decreased with increased additive amount because the aluminum and oxygen in the YA system dissolved into β-Si₃N₄ grains to form a β-SiAlON solid solution, which acted as a point defect for phonon scattering. The key processsing parameters for high thermal conductivity of Si₃N₄ were the sintering temperature and additive composition.     

Microstructural Development of Calcium alpha-SiAlON Ceramics with Elongated Grains

Silicon nitride (Si₃N₄) and SiAlONs can be self-toughened through the growth of elongated β-Si₃N₄/β-SiAlON grains in sintering. α-SiAlONs usually retain an equiaxed grain morphology and have a higher hardness but lower toughness than β-SiAlONs. The present work has demonstrated that elongated alpha-SiAlON grains can also be developed through pressureless sintering. alpha-SiAlONs with high-aspect-ratio grains in the calcium SiAlON system have exhibited significant grain debonding and pull-out effects during fracture, which offers promise for in-situ -toughened α-SiAlON ceramics.     

Residual α–Si3N4 in O' Crystals in CeO2-Doped O'+β' SiAlON Ceramics

The microstructure of a pressureless sintered (1605°C, 90 min) O'+β' SiAlON ceramic with CeO₂ doping has been investigated. It is duplex in nature, consisting of very large, slablike elongated O' grains (20–30 μm long), and a continuous matrix of small rodlike β' grains (< 1.0 μm in length). Many α-Si₃N₄ inclusions (0.1–0.5 μm in size) were found in the large O' grains. CeO₂-doping and its high doping level as well as the high Al₂O₃ concentration were thought to be the main reasons for accelerating the reaction between the α-Si₃N₄ and the Si-Al-O-N liquid to precipitate O'–SiAlON. This caused the supergrowth of O' grains. The rapid growth of O' crystals isolated the remnant α–Si₃N₄ from the reacting liquid, resulting in a delay in the α→β-Si₃N₄ transformation. The large O' grains and the α-Si₃N₄ inclusions have a pronounced effect on the strength degradation of O'+β' ceramics.     

Relationship between Microstructure and Mechanical Performance of a 70% Silicon Nitride–30% Barium Aluminum Silicate Self-Reinforced Ceramic Composite

The abnormal grain growth of β-Si₃N₄ was observed in a 70% Si₃N₄–30% barium aluminum silicate (70%-Si₃N₄–30%-BAS) self-reinforced composite that was pressureless-sintered at 1930°C; Si₃N₄ starting powders with a wide particle-size distribution were used. The addition of coarse Si₃N₄ powder encouraged the abnormal growth of β-Si₃N₄ grains, which allowed microstructural modification through control of the content and size distribution of β-Si₃N₄ nuclei. The mechanical response of different microstructures was characterized in terms of flexural strength, as well as indentation fracture resistance, at room temperature. The presence of even a small amount of abnormally grown β-Si₃N₄ grains improved the fracture toughness and minimized the variability in flexural strength.     

Fabrication of Si3N4/SiC Composite by Reaction-Bonding and Gas-Pressure Sintering

Si₃N₄/SiC composite materials have been fabricated by reaction-sintering and postsintering steps. The green body containing Si metal and SiC particles was reaction-sintered at 1370°C in a flowing N₂/H₂ gas mixture. The initial reaction product was dominated by alpha-Si₃N₄. However, as the reaction processed there was a gradual increase in the proportion of β-Si₃N₄. The reaction-bonded composite consisting of alpha-Si₃N₄, β-Si₃N₄, and SiC was heat-treated again at 2000°C for 150 min under 7-MPa N₂ gas pressure. The addition of SiC enhanced the reaction-sintering process and resulted in a fine microstructure, which in turn improved fracture strength to as high as 1220 MPa. The high value in flexural strength is attributed to the formation of uniformly elongated β-Si₃N₄ grains as well as small size of the grains (length = 2 μm, thickness = 0.5 μm). The reaction mechanism of the reaction sintering and the mechanical properties of the composite are discussed in terms of the development of microstructures.     

Influence of Planetary High-Energy Ball Milling on Microstructure and Mechanical Properties of Silicon Nitride Ceramics

The influence of ball-milling methods on microstructure and mechanical properties of silicon nitride (Si₃N₄) ceramics produced by pressureless sintering for a sintering additive from MgO–Al₂O₃–SiO₂ system was investigated. For planetary high-energy ball milling, the mechanical properties of Si₃N₄ ceramics were evidently improved and a homogeneous microstructure developed. In contrast, some exaggerated elongated grains were developed due to the local enrichment of sintering additives in the specimen prepared by general ball milling. For Si₃N₄ ceramics produced by planetary ball milling, flexure strength of 1.06 GPa, Vickers hardness of 14.2 GPa, and fracture toughness of 6.6 MPa·m^0.5 were achieved. The differences in the mechanical properties of Si₃N₄ ceramics produced by different processing seem to arise mainly from the changes in microstructural homogenization and sinterability. The planetary high-energy ball-milling process provides a good route to mix starting powders for developing ceramics with uniform microstructure and promising mechanical properties.     

Densification of Si3N4 with LiYO2 Additive

This paper deals with the densification and phase transformation during pressureless sintering of Si₃N₄ with LiYO₂ as the sintering additive. The dilatometric shrinkage data show that the first Li₂O- rich liquid forms as low as 1250°C, resulting in a significant reduction of sintering temperature. On sintering at 1500°C the bulk density increases to more than 90% of the theoretical density with only minor phase transformation from α-Si₃N₄ to β-Si₃N₄ taking place. At 1600°C the secondary phase has been completely converted into a glassy phase and total conversion of α-Si₃N₄ to β-Si₃N₄ takes place. The grain growth is anisotropic, leading to a microstructure which has potential for enhanced fracture toughness. Li₂O evaporates during sintering. Thus, the liquid phase is transient and the final material might have promising mechanical properties as well as promising high-temperature properties despite the low sintering temperature. The results show that the Li₂O−Y₂O₃ system can provide very effective low-temperature sintering additives for silicon nitride.     

Fabrication and Mechanical Properties of Silicon Carbide-Silicon Nitride Composites with Oxynitride Glass

A microstructure that consisted of uniformly distributed, elongated β-Si₃N₄ grains, equiaxed β-SiC grains, and an amorphous grain-boundary phase was developed by using β-SiC and alpha-Si₃N₄ powders. By hot pressing, elongated β-Si₃N₄ grains were grown via alpha right arrow β phase transformation and equiaxed β-SiC grains were formed because of inhibited grain growth. The strength and fracture toughness of SiC have been improved by adding Si₃N₄ particles, because of the reduced defect size and the enhanced bridging and crack deflection by the elongated β-Si₃N₄ grains. Typical flexural-strength and fracture-toughness values of SiC-35-wt%-Si₃N₄ composites were 1020 MPa and 5.1 MPam^1/2, respectively.     

Fabrication of Textured Si3N4 Ceramics by Slip Casting in a High Magnetic Field

Developing the texture of ceramics is one of the effective ways for improving properties. Although the magnetic susceptibility of nonmagnetic materials is very small, there is a possibility to control the crystal orientation using a high magnetic field due to a magnetic anisotropy. In this study, Si₃N₄ ceramics were manufactured by a slip-casting process under high magnetic field and pressureless sintering. The texture of Si₃N₄ ceramics was studied using X-ray diffraction and scanning electron micrographs of polished and plasma-etched specimens. It has been found that most of the a,b -axes texture of β-Si₃N₄ grains aligned to the magnetic field direction.     

Microstructural Development During Gas-Pressure Sintering of α-Silicon Nitride

Gas-pressure sintering of α-Si₃N₄ was carried out at 1850 ° to 2000°C in 980-kPa N₂. The diameters and aspect ratios of hexagonal grains in the sintered materials were measured on polished and etched surfaces. The materials have a bimodal distribution of grain diameters. The average aspect ratio in the materials from α-Si₃N₄ powder was similar to that in the materials from β-Si₃N₄ powder. The aspect ratio of large and elongated grains was larger than that of the average for all grains. The development of elongated grains was related to the formation of large nuclei during the α-to-β phase transformation. The fracture toughness of gaspressure-sintered materials was not related to the α content in the starting powder or the aspect ratio of the grains, but to the diameter of the large grains. Crack bridging was the main toughening mechanism in gas-pressure-sintered Si₃N₄ ceramics.     

Impurity Phases in Hot-Pressed Si3N4

Impurity phases in commercial hot-pressed Si₃N₄ were investigated using transmission electron microscopy. In addition to the dominant, β-Si₃N₄ phase, small amounts of Si₂N₂O, SiC, and WC were found. Significantly, a continuous grain-boundary phase was observed in the ∼ 25 high-angle boundaries examined. This film is ∼ 10 Å thick between, β-Si₃N₄ grains and ∼ 30 Å thick between Si₂N₂O and β-Si₃N₄ grains.