Effect of electrolyte composition on initial cycling and impedance characteristics of lithium-ion cells

Hybrid-electric vehicles require lithium-battery electrolytes that form stable, low impedance passivation layers to protect the electrodes, while allowing rapid lithium-ion transport under high current charge/discharge pulses. In this article, we describe data acquired on cells containing LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes, graphite-based negative electrodes, and electrolytes with lithium hexafluorophosphate (LiPF₆), lithium tetrafluoroborate (LiBF₄), lithium bis(oxalato)borate (LiBOB) and lithium difluoro(oxalato) borate (LiF₂OB) salts. The impedance data were collected in cells containing a Li–Sn reference electrode to determine effect of electrolyte composition and testing temperature on individual electrode impedance. The full cell impedance data showed the following trend: LiBOB > LiBF₄ > LiF₂OB > LiPF₆. The negative electrode impedance showed a trend similar to that of the full cell; this electrode was the main contributor to impedance in the LiBOB and LiBF₄ cells. The positive electrode impedance values for the LiBF₄, LiF₂OB, and LiPF₆ cells were comparable; the values were somewhat higher for the LiBOB cell. Cycling and impedance data were also obtained for cells containing additions of LiBF₄, LiBOB, LiF₂OB, and vinylene carbonate (VC) to the EC:EMC (3:7 by wt.) + 1.2 M LiPF₆ electrolyte. Our data indicate that the composition and morphology of the graphite SEI formed during the first lithiation cycle is an important determinant of the negative electrode impedance, and hence full cell impedance.     

Comparison of the electrochemical properties of LiBOB and LiPF6 in electrolytes for LiMn2O4/Li cells

The electrochemical stability and conductivity of LiPF₆ and lithium bis(oxalato)borate (LiBOB) in a ternary mixture of ethylene carbonate (EC), ethyl methyl carbonate (EMC) and diethyl carbonate (DEC) were compared. The discharge capacities of LiMn₂O₄/Li cells with the two electrolytes were measured at various current densities. At room temperature, LiMn₂O₄/Li cells with the electrolyte containing LiBOB cycled equally well with those using the electrolyte containing LiPF₆ when the discharge current rate was under 1 C. At 60 °C, the LiBOB-based electrolyte cycled better than the LiPF₆-based electrolyte even when the discharge current rate was above 1 C. Compared with the electrolyte containing LiPF₆, in LiMn₂O₄/Li cells the electrolyte containing LiBOB exhibited better capacity utilization and capacity retention at both room temperature and 60 °C. The scanning electron microscopy (SEM) images and the a.c. impedance measurements demonstrated that the electrode in the electrolyte containing LiBOB was more stable. In summary, LiBOB offered obvious advantages in LiMn₂O₄/Li cells.     

A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Effect of ball milling on structural and electrochemical properties of (PEO)nLiX (LiX = LiCF3SO3 and LiBF4) polymer electrolytes

Polymer electrolytes consisting of poly(ethylene oxide) (PEO) and lithium salts, such as LiCF₃SO₃ and LiBF₄ are prepared by the ball-milling method. This is performed at various times (2, 4, 8, 12 h) with ball:sample ratio of 400:1. The electrochemical and thermal characteristics of the electrolytes are evaluated. The structure and morphology of PEO–LiX polymer electrolyte is changed to amorphous and smaller spherulite texture by ball milling. The ionic conductivity of the PEO–LiX polymer electrolytes increases by about one order of magnitude than that of electrolytes prepared without ball milling. Also, the ball milled electrolytes have remarkably higher ionic conductivity at low temperature. Maximum ionic conductivity is found for the PEO–LiX prepared by ball milling for 12 h, viz. 2.52×10⁻⁴ S cm⁻¹ for LiCF₃SO₃ and 4.99×10⁻⁴ S cm⁻¹ for LiBF₄ at 90 °C. The first discharge capacity of Li/S cells increases with increasing ball milling time. (PEO)₁₀LiCF₃SO₃ polymer electrolyte prepared by ball milling show the typical two plateau discharge curves in a Li/S battery. The upper voltage plateau for the polymer electrolyte containing LiBF₄ differs markedly from the typical shape.     

Electrochemical performance of nanostructured spinel LiMn2O4 in different aqueous electrolytes

A nanostructured spinel LiMn₂O₄ electrode material was prepared via a room-temperature solid-state grinding reaction route starting with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O) and citric acid (C₆H₈O₇·H₂O) raw materials, followed by calcination of the precursor at 500 °C. The material was characterized by X-ray diffraction (XRD) and transmission electron microscope techniques. The electrochemical performance of the LiMn₂O₄ electrodes in 2 M Li₂SO₄, 1 M LiNO₃, 5 M LiNO₃ and 9 M LiNO₃ aqueous electrolytes was studied using cyclic voltammetry, ac impedance and galvanostatic charge/discharge methods. The LiMn₂O₄ electrode in 5 M LiNO₃ electrolyte exhibited good electrochemical performance in terms of specific capacity, rate dischargeability and charge/discharge cyclability, as evidenced by the charge/discharge results.     

Discharge properties of all-solid sodium–sulfur battery using poly (ethylene oxide) electrolyte

An all-solid sodium/sulfur battery using poly (ethylene oxide) (PEO) polymer electrolyte are prepared and tested at 90 °C. Each battery is composed of a solid sulfur electrode, a sodium metal electrode, and a solid PEO polymer electrolyte. During the first discharge, the battery shows plateau potentials at 2.27 and at 1.76 V. The first discharge capacity is 505 mAh g⁻¹ sulfur at 90 °C. The capacity drastically decreases by repeated on charge–discharge cycling but remains at 166 mAh g⁻¹ sulfur after 10 cycles. The latter value is higher than that reported for a Na/poly (vinylidene difluoride)/S battery at room temperature.     

Novel electrospun poly(vinylidene fluoride-co-hexafluoropropylene)–in situ SiO2 composite membrane-based polymer electrolyte for lithium batteries

Composite membranes of poly(vinylidene fluoride-co-hexafluoropropylene) {P(VdF-HFP)} and different composition of silica have been prepared by electrospinning polymer solution containing in situ generated silica. These membranes are made up of fibers of 1–2 μm diameters. These fibers are stacked in layers to produce fully interconnected pores that results in high porosity. Polymer electrolytes were prepared by immobilizing 1 M LiPF₆ in ethylene carbonate (EC)/dimethyl carbonate (DMC) in the membranes. The composite membranes exhibit a high electrolyte uptake of 550–600%. The optimum electrochemical properties have been observed for the polymer electrolyte containing 6% in situ silica to show ionic conductivity of 8.06 mS cm⁻¹ at 20 °C, electrolyte retention ratio of 0.85, anodic stability up to 4.6 V versus Li/Li⁺, and a good compatibility with lithium metal resulting in low interfacial resistance. A first cycle specific capacity of 170 mAh g⁻¹ was obtained when the polymer electrolyte was evaluated in a Li/lithium iron phosphate (LiFePO₄) cell at 0.1 C-rate at 25 °C, corresponding to 100% utilization of the cathode material. The properties of composite membrane prepared with in situ silica were observed to be comparatively better than the one prepared by direct addition of silica.     

Effect of synthetic conditions on the electrochemical properties of LiMn0.4Fe0.6PO4/C synthesized by sol–gel technique

Carbon-coated LiMn_0.4Fe_0.6PO₄ (LMFP) was synthesized by sol–gel technique using citric acid as foaming agent and carbon precursor. To evaluate the effect of synthetic conditions on the electrochemical properties of LMFP for use as cathode active material, the carbon-coated olivines were synthesized by a two-step thermal treatment at different temperatures. The composites were characterized by elemental analysis, XRD, SEM, TEM, Raman microprobe spectroscopy and their electrochemical properties were also studied. The composite that shows the better electrochemical performance has more porous structure, lower D/G band ratio in Raman spectra, and charge and discharge capacities of same 155 mAh g⁻¹ with higher material utilization of 97% at 0.1 C-rate (0.05 mA cm⁻²). The material exhibiting the better performance was also incorporated in a polymer electrolyte hosted in an electrospun P(VdF-HFP) membrane. The lithium polymer battery composed of LiMn_0.4Fe_0.6PO₄ cathode and polymer electrolyte showed a good cycling performance with the initial discharge capacity of 146 mAh g⁻¹.     

Fabrication of all solid-state lithium-ion batteries with three-dimensionally ordered composite electrode consisting of Li0.35La0.55TiO3 and LiMn2O4

A composite electrode between three-dimensionally ordered macroporous (3DOM) Li_0.35La_0.55TiO₃ (LLT) and LiMn₂O₄ was fabricated by colloidal crystal templating method and sol–gel process. A close-packed PS beads with the opal structure was prepared by filtration of a suspension containing PS beads. Li–La–Ti–O sol was injected by vacuum impregnation process into the voids between PS beads, and then was heated to form 3DOM-LLT. Three-dimensionally ordered composite material consisting of LiMn₂O₄ and LLT was prepared by sol–gel process. The prepared composite was characterized with SEM and XRD. All solid-state Li-ion battery was fabricated with the LLT–LiMn₂O₄ composite electrode as a cathode, dry polymer electrolyte and Li metal anode. The prepared all solid-state cathode exhibited a volumetric discharge capacity of 220 mAh cm⁻³.     

Boron doped lithium trivanadate as a cathode material for an enhanced rechargeable lithium ion batteries

Boron was doped into lithium trivanadate through an aqueous reaction process followed by heating at 100 °C. The B-LiV₃O₈ materials as a cathode in lithium batteries exhibits a specific discharge capacity of 269.4 mAh g⁻¹ at first cycle and remains 232.5 mAh g⁻¹ at cycle 100, at a current density of 150 mAh g⁻¹ in the voltage range of 1.8–4.0 V. The B-LiV₃O₈ materials show excellent stability, with the retention of 86.30% after 100 cycles. These result values are higher than those previous reports indicating B-LiV₃O₈ prepared by our synthesis method is a promising candidate as cathode material for rechargeable lithium batteries. The enhanced discharge capacities and their stabilities indicate that boron atoms promote lithium transferring and intercalating/deintercalating during the electrochemical processes and improve the electrochemical performance of LiV₃O₈ cathode.     

Mechanochemical synthesis of α-Fe2O3 nanoparticles and their application to all-solid-state lithium batteries

α-Fe₂O₃ fine particles have been prepared by a mechanochemical process and a solution process. α-Fe₂O₃ nanoparticles with aggregates composed of the several tens nm primary particles were produced by the mechanochemical process. The nanoparticles were applied to the electrode as an active material for all-solid-state lithium batteries and the electrochemical properties of the cell were investigated. Typical charge–discharge curves, as seen in the liquid type cell using the α-Fe₂O₃ nanoparticles as an electrode were observed in the all-solid-state cell. The first discharge capacity of the cell of about 780 mAh g⁻¹ was, however, smaller than the capacity of a cell using α-Fe₂O₃ particles prepared by the solution process, which were monodispersed particles of 250 nm without aggregates. In order to develop electrochemical performance of all-solid-state batteries, it is important to use the electrode particles without aggregation which lead to the formation of good solid–solid interface between active material and solid electrolyte particles.C     

Preparation and electrochemical properties of lithium–sulfur polymer batteries

The lithium/sulfur (Li–S) batteries consist of a composite cathode, a polymer electrolyte, and a lithium anode. The composite cathode is made from elemental sulfur (or lithium sulfide), carbon black, PEO, LiClO₄, and acetonitrile. The polymer electrolyte is made of gel-type linear poly(ethylene oxide) (PEO) with tetra ethylene glycol dimethyl ether. Cells based on Li₂S or sulfur have open-circuit voltages of about 2.2 and 2.5 V, respectively. The former cell shows two reduction peaks and one oxidation peak. It is suggested that the first reduction peak is caused by the change from polysulfide to short lithium polysulfide, and the second reduction peak by the change from short lithium polysulfide to lithium sulfide (Li₂S, Li₂S₂). The cell based on sulfur has the same reduction mechanism as that of Li₂S, which is caused by the multi process (first and second reduction) of lithium polysulfide. On charge–discharge cycling, the first discharge has a higher capacity than subsequent discharges and the flat discharge voltage is about 2.0 V. As the current load is increased, the discharge capacity decreases. One reason for this fading capacity and low sulfur utilization is the aggregation of sulfur (or polysulfide) with cycling.     

A low temperature electrolyte for primary Li/CFx batteries

In this work, a 1:1 by weight blend of acetonitrile (AN) and γ-butyrolactone (BL) was studied as the solvent of low temperature electrolyte for high energy density Li/CF_x batteries. Both visual observation and impedance analysis show that metallic Li is kinetically stable in a 0.5 m LiBF₄ 1:1 AN/BL electrolyte. This property is attributed to the formation of a protective passivation film on the surface of metallic Li, and it has been successfully used to develop the low temperature electrolyte for Li/CF_x cells. It is shown that the cell with such an electrolyte outperforms the control cell with 0.5 m LiBF₄ 1:1 (wt.) propylene carbonate (PC)/1,2-dimethoxyethane (DME) electrolyte in both power capability and low temperature discharge performance. Impedance analyses reveal that the improved discharge performance is attributed to the reduction in both the bulk resistance and cell reaction resistance of the Li/CF_x cell, which is related to the high ionic conductivity of the AN/BL electrolyte. Due to the chemical incompatibility between metallic Li and AN at high temperatures, the storage and operation temperature for the Li/CF_x cells with 0.5 m LiBF₄ 1:1 AN/BL electrolyte is limited to or below ambient temperature (30 °C).     

Boosting the performance of poly(ethylene oxide)-based solid polymer electrolytes by blending with poly(vinylidene fluoride-co-hexafluoropropylene) for solid-state lithium-ion batteries

To seek a solid polymer electrolyte (SPE) with excellent performance, a novel poly(ethylene oxide) (PEO) based SPE is prepared by blending an appropriate amount of microcrystalline poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) with PEO using a universal solution casting method. Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD) and differential scanning calorimetry (DSC) are utilized to analyse the samples. The crystallinity of the blend solid polymer electrolyte is significantly lower than that of the neat PEO-based SPE. The addition of the PVDF-HFP disrupts the segment structure of the PEO crystal region and increases the proportion of the amorphous region, thus boosting the migration of lithium ions. The results show that the electrochemical stability window of the blend solid polymer electrolyte reaches as high as 4.8 V. The initial discharge specific capacity of the solid-state LiFePO₄/SPE/Li battery is 131 mAh g⁻¹ at 0.5 C and 60°C, and the discharge specific capacity is still 110.5 mAh g⁻¹ after 100 cycles. On the basis of the results, the novel SPE has a widespread application prospects in solid-state lithium-ion batteries.     

Lithium oxalyldifluoroborate/carbonate electrolytes for LiFePO4/artificial graphite lithium-ion cells

The electrolytes based on lithium oxalyldifluoroborate (LiODFB) and carbonates have been systematically investigated for LiFePO₄/artificial graphite (AG) cells, by ionic conductivity test and various electrochemical tests, such as cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge-discharge test. The conductivity of nine electrolytes as a function of solvent composition and LiODFB salt concentration has been studied. The coulombic efficiency of LiFePO₄/Li and AG/Li half cells with these electrolytes have also been compared. The results show that 1 M LiODFB EC/PC/DMC (1:1:3, v/v) electrolyte has a relatively higher conductivity (8.25 mS cm⁻¹) at 25 °C, with high coulombic efficiency, good kinetics characteristics and low interface resistance. With 1 M LiODFB EC/PC/DMC (1:1:3, v/v) electrolyte, LiFePO₄/AG cells exhibit excellent capacity retention ∼92% and ∼88% after 100 cycles at 25 °C and at elevated temperatures up to 65 °C, respectively; The LiFePO₄/AG cells also have good rate capability, the discharge capacity is 324.8 mAh at 4 C, which is about 89% of the discharge capacity at 0.5 C. However, at −10 °C, the capacity is relatively lower. Compared with 1 M LiPF₆ EC/PC/DMC (1:1:3, v/v), LiFePO₄/AG cells with 1 M LiODFB EC/PC/DMC (1:1:3, v/v) exhibited better capacity utilization at both room temperature and 65 °C. The capacity retention of the cells with LiODFB-based electrolyte was much higher than that of LiPF₆-based electrolyte at 65 °C, while the capacity retention and the rate capacity of the cells is closed to that of LiPF₆-based electrolyte at 25 °C. In summary, 1 M LiODFB EC/PC/DMC (1:1:3, v/v) is a promising electrolyte for LiFePO₄/AG cells.     

Effect of electrolyte on electrochemical characteristics of MmNi3.55Co0.72Al0.3Mn0.43 alloy electrode for hydrogen storage

A series of experiments have been performed to investigate the effects of three electrolytes of different compositions (EO, EA and EM) on the electrochemical characteristics of MmNi_3.55Co_0.72Al_0.3Mn_0.43 hydrogen storage alloy electrode. Electrolytes EA and EM were obtained by adding appropriate amounts of Al₂(SO₄)₃ and MnSO₄ to the original electrolyte EO (6 M KOH + 1 wt% LiOH), respectively. Electrode activation, maximum capacity, cycle life, self-discharge and high-rate discharge characteristics have been studied. It was found that a maximum capacity of about 260 mA h/g has been obtained for the alloy electrodes in all these electrolytes after 5–7 cycles of charging/discharging. The alloy electrodes have a good durability in electrolytes EA and EM, especially after 175 cycles. Using the capacity retention as an indication of self-discharge resistance, almost identical degree of capacity retention (82% after 4 days and 45% after 16 days) has been observed at 298 K, regardless of the electrolytes used. When tested at higher temperature, however, a higher capacity retention (46% after 3 days) at 333 K has been observed for electrodes in electrolyte EA, and about 32% for electrodes in both electrolytes EO and EM. As to high-rate discharge behavior of the results of high-rate discharge tests indicated that about 50% of discharge efficiencies were obtained in the three electrolytes at 333 K by continuous-model high-rate discharge method, at a discharge rate of 7C, and 22% in 298 K. The alloy electrode in electrolyte EM has the best durability, in which about 50% of discharge efficiency at DC = 9C was obtained by step-model high-rate discharge method at 333 K, which was even higher than that at 298 K.     

Effect of NaI/I2 mediators on properties of PEO/LiAlO2 based all-solid-state supercapacitors

NaI/I₂ mediators and activated carbon were added into poly(ethylene oxide) (PEO)/lithium aluminate (LiAlO₂) electrolyte to fabricate composite electrodes. All solid-state supercapacitors were fabricated using the as prepared composite electrodes and a Nafion 117 membrane as a separator. Cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge measurements were conducted to evaluate the electrochemical properties of the supercapacitors. With the addition of NaI/I₂ mediators, the specific capacitance increased by 27 folds up to 150 F g⁻¹. The specific capacitance increased with increases in the concentration of mediators in the electrodes. The addition of mediators also reduced the electrode resistance and rendered a higher electron transfer rate between mediator and mediator. The stability of the all-solid-state supercapacitor was tested over 2000 charge/discharge cycles.     

Basic molten salt process—A new route for synthesis of nanocrystalline Li4Ti5O12-TiO2 anode material for Li-ion batteries using eutectic mixture of LiNO3-LiOH-Li2O2

A nanocrystalline Li₄Ti₅O₁₂-TiO₂ duplex phase has been synthesized by a simple basic molten salt process (BMSP) using an eutectic mixture of LiNO₃-LiOH-Li₂O₂ at 400-500 °C. The microstructure and morphology of the Li₄Ti₅O₁₂-TiO₂ product are characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The sample prepared by heat-treating at 300 °C for 3 h (S-1) reveals dense agglomerates of ultra-fine nanocrystalline Li₄Ti₅O₁₂; with heat treatment at 400 °C for 3 h (S-2), there is a duplex crystallite size (fine < 10 nm, and coarse > 20 nm) of Li₄Ti₅O₁₂-TiO₂; at 500 °C for 3 h (S-3), a much coarser and less-dense distribution of lithium titanate (crystallite size ∼15-30 nm) is observed. According to the results of electrochemical testing, the S-2 sample shows initial discharge capacities of 193 mAh g⁻¹ at 0.2 C, 168 mAh g⁻¹ at 0.5 C, 146 mAh g⁻¹ at 1 C, 135 mAh g⁻¹ at 2 C, and 117 mAh g⁻¹ at 5 C. After 100 cycles, the discharge capacity is 138 mAh g⁻¹ at 1 C with a capacity retention of 95%. The S-2 sample yields the best electrochemical performance in terms of charge-discharge capacity and rate capability compared with other samples. Its superior electrochemical performance can be mainly attributed to the duplex crystallite structure, composed of fine (<10 nm) and coarse (>20) nm nanoparticles, where lithium ions can be stored within the grain boundary interfaces between the spinel Li₄Ti₅O₁₂ and the anatase TiO₂.     

Nonflammable electrolyte for 3-V lithium-ion battery with spinel materials LiNi0.5Mn1.5O4 and Li4Ti5O12

The compatibility between dimethyl methylphosphonate (DMMP)-based electrolyte of 1 M LiPF₆/EC + DMC + DMMP (1:1:2 wt.) and spinel materials Li₄Ti₅O₁₂ and LiNi_0.5Mn_1.5O₄ was reviewed, respectively. The cell performance and impedance of 3-V LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ lithium-ion cell with the DMMP-based nonflammable electrolyte was compared with the baseline electrolyte of 1 M LiPF₆/EC + DMC (1:1 wt.). The nonflammable DMMP-based electrolyte exhibited good compatibility with spinel Li₄Ti₅O₁₂ anode and high-voltage LiNi_0.5Mn_1.5O₄ cathode, and acceptable cycling performance in the LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ full-cell, except for the higher impedance than that in the baseline electrolyte. All of the results disclosed that the 3 V LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ lithium-ion battery was a promising choice for the nonflammable DMMP-based electrolyte.     

Preparation of manganese oxide with high density by decomposition of MnCO3 and its application to synthesis of LiMn2O4

Manganese oxide with high tap density was prepared by decomposition of spherical manganese carbonate, and then LiMn₂O₄ cathode materials were synthesized by solid-state reaction between the manganese oxide and lithium carbonate. Structure and properties of the samples were determined by X-ray diffraction, Brunauer–Emmer–Teller surface area analysis, scanning electron microscope and electrochemical measurements. With increase of the decomposition temperature from 350 °C to 900 °C, the tap density of the manganese oxide rises from 0.91 g cm⁻³ to 2.06 g cm⁻³. Compared with the LiMn₂O₄ cathode made from chemical manganese dioxide or electrolytic manganese dioxide, the LiMn₂O₄ made from manganese oxide of this work has a larger tap density (2.53 g cm⁻³), and better electrochemical performances with an initial discharge capacity of 117 mAh g⁻¹, a capacity retention of 93.5% at the 15th cycle and an irreversible capacity loss of 2.24% after storage at room temperature for 28 days.