High power and high capacity cathode material LiNi0.5Mn0.5O2 for advanced lithium-ion batteries

Single-phase lithium nickel manganese oxide, LiNi_0.5Mn_0.5O₂, was successfully synthesized from a solid solution of Ni_1.5Mn_1.5O₄ that was prepared by means of the solid reaction between Mn(CH₃COO)₂·4H₂O and Ni(CH₃COO)₂·4H₂O. XRD pattern shows that the product is well crystallized with a high degree of Li–M (Ni, Mn) order in their respective layers, and no diffraction peak of Li₂MnO₃ can be detected. Electrochemical performance of as-prepared LiNi_0.5Mn_0.5O₂ was examined in the test battery by charge–discharge cycling with different rate, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The cycling behavior between 2.5 and 4.4 V at a current rate of 21.7 mA g⁻¹ shows a reversible capacity of about 190 mAh g⁻¹ with little capacity loss after 100 cycles. High-rate capability test shows that even at a rate of 6C, stable capacity about 120 mAh g⁻¹ is retained. Cyclic voltammetry (CV) profile shows that the cathode material has better electrochemical reversibility. EIS analysis indicates that the resistance of charge transfer (R_ct) is small in fully charged state at 4.4 V and fully discharged state at 2.5 V versus Li⁺/Li. The favorable electrochemical performance was primarily attributed to regular and stable crystal structure with little intra-layer disordering.     

Solution combustion synthesis of layered LiNi0.5Mn0.5O2 and its characterization as cathode material for lithium-ion cells

LiNi_0.5Mn_0.5O₂, a promising cathode material for lithium-ion batteries, is synthesized by a novel solution-combustion procedure using acenaphthene as a fuel. The powder X-ray diffraction (XRD) pattern of the product shows a hexagonal cell with a = 2.8955 Å and c = 14.1484 Å. Electron microscopy investigations indicate that the particles are of sub-micrometer size. The product delivers an initial discharge capacity of 161 mAh g⁻¹ between 2.5 and 4.6 V at a 0.1 C rate and could be subjected to more than 50 cycles. The electrochemical activity is corroborated with cyclic voltammetric (CV) and electrochemical impedance data. The preparative procedure presents advantages such as a low cation mixing, sub-micron particles and phase purity.     

The influence of compositional change of 0.3Li2MnO3·0.7LiMn1−xNiyCo0.1O2 (0.2 ≤ x ≤ 0.5, y = x − 0.1) cathode materials prepared by co-precipitation

Cathode materials prepared by a co-precipitation are 0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (0.2 ≤ x ≤ 0.4) cathode materials with a layered-spinel structure. In the voltage range of 2.0-4.6 V, the cathodes show more than one redox reaction peak during its cyclic voltammogram. The Li/0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (x = 0.3, y = 0.2) cell shows the initial discharge capacity of about 200 mAh g⁻¹. However, when x = 0.2 and y = 0.1, the cell exhibits a rapid decrease in discharge capacity and poor cycle life.     

Surface modification of LiNi0.5Mn1.5O4 by ZrP2O7 and ZrO2 for lithium-ion batteries

The spinel LiNi_0.5Mn_1.5O₄ has been surface modified separately with 1.0 wt.% ZrO₂ and ZrP₂O₇ for the purpose of improving its cycle performance as a cathode in a 5-V lithium-ion cell. Although the modifications did not change the crystallographic structure of the surface-modified samples, they exhibited better cyclability at elevated temperature (55 °C) compared with pristine LiNi_0.5Mn_1.5O₄. The material that was surface modified with ZrO₂ gave the best cycling performance, only 4% loss of capacity after 150 cycles at 55 °C. Electrochemical impedance spectroscopy demonstrated that the improved performance of the ZrO₂-surface-modified LiNi_0.5Mn_1.5O₄ is due to a small decrease in the charge transfer resistance, indicating limited surface reactivity during cycling. Differential scanning calorimetry showed that the ZrO₂-modified LiNi_0.5Mn_1.5O₄ exhibits lower heat generation and higher onset reaction temperature compared to the pristine material. The excellent cycling and safety performance of the ZrO₂-modified LiNi_0.5Mn_1.5O₄ electrode was found to be due to the protective effect of homogeneous ZrO₂ nano-particles that form on the LiNi_0.5Mn_1.5O₄, as shown by transmission electron microscopy.     

Synthesis and electrochemical performance of the high voltage cathode material Li[Li0.2Mn0.56Ni0.16Co0.08]O2 with improved rate capability

The high voltage layered Li[Li_0.2Mn_0.56Ni_0.16Co_0.08]O₂ cathode material, which is a solid solution between Li₂MnO₃ and LiMn_0.4Ni_0.4Co_0.2O₂, has been synthesized by co-precipitation method followed by high temperature annealing at 900 °C. XRD and SEM characterizations proved that the as prepared powder is constituted of small and homogenous particles (100-300 nm), which are seen to enhance the material rate capability. After the initial decay, no obvious capacity fading was observed when cycling the material at different rates. Steady-state reversible capacities of 220 mAh g⁻¹ at 0.2C, 190 mAh g⁻¹ at 1C, 155 mAh g⁻¹ at 5C and 110 mAh g⁻¹ at 20C were achieved in long-term cycle tests within the voltage cutoff limits of 2.5 and 4.8 V at 20 °C.     

Effects of supersonic treatment on the electrochemical properties and crystal structure of LiMn1.5Ni0.5O4 as a cathode material for Li ion batteries

The electrochemical properties and crystal structure of LiMn_1.5Ni_0.5O₄ treated with supersonic waves in an aqueous Ni-containing solution were investigated by performing charge-discharge tests, inductively coupled plasma (ICP) analysis, scanning electron microscopy (SEM), iodometry, X-ray diffraction (XRD), powder neutron diffraction and synchrotron powder XRD. The charge-discharge curve of LiMn_1.5Ni_0.5O₄ versus Li/Li⁺ has plateaus at 4.1 and 4.7 V. The 4.1 V versus Li/Li⁺ plateau due to the oxidation of Mn^3+/4+ was reduced by the supersonic treatment. During the charge-discharge cycling test at 25 °C, the supersonic treatment increased the discharge capacity of the 50th cycle. Rietveld analysis of the neutron diffraction patterns revealed that the Ni occupancy of the 4b site in LiMn_1.5Mn_0.5O₄, which is mainly occupied by Ni, was increased by the supersonic treatment. This result suggests that Ni²⁺ is partially substituted for Mn^3+/4+ during the supersonic treatment.     

Synthesis and electrochemical properties of Li1−xFe0.8Ni0.2O2–LixMnO2 (Mn/(Fe + Ni + Mn) = 0.8) material

A new type of Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ (Mn/(Fe + Ni + Mn) = 0.8) material was synthesized at 350 °C in air atmosphere using a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−xFeO₂–Li_xMnO₂ (Mn/(Fe + Mn) = 0.8) with much reduced impurity peaks. The Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell showed a high initial discharge capacity above 192 mAh g⁻¹, which was higher than that of the parent Li/Li_1−xFeO₂–Li_xMnO₂ (186 mAh g⁻¹). We expected that the increase of initial discharge capacity and the change of shape of discharge curve for the Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell is the result from the redox reaction from Ni²⁺ to Ni³⁺ during charge/discharge process. This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles.     

Evaluation of nano-structured Ir0.5Mn0.5O2 as a potential cathode for intermediate temperature solid oxide fuel cell

A novel Ir_0.5Mn_0.5O₂ cathode has been synthesized by thermal decomposition of mixed H₂IrCl₆ and Mn(NO₃)₂ water solution. The Ir_0.5Mn_0.5O₂ cathode has been characterized by XRD, field emission SEM (FESEM) and AC impedance spectroscopy. XRD result shows that rutile-structured Ir_0.5Mn_0.5O₂ phase is formed by thermal decomposition of mixed H₂IrCl₆ and Mn(NO₃)₂ water solution. FESEM micrographs show that a porous structure with well-necked particles forms in the cathode after sintering at 1000 °C. The average grain size is between 20 and 30 nm. Two depressed arcs appear in the medium-frequency and low-frequency region, indicating that there are at least two different processes in the cathode reaction: charge transfer and molecular oxygen dissociation followed by surface diffusion. The minimum area specific resistance (ASR) is 0.67 Ω cm² at 800 °C. The activation energy for the total oxygen reduction reaction is 93.7 kJ mol⁻¹. The maximum power densities of the Ir_0.5Mn_0.5O₂/LSGM/Pt cell are 43.2 and 80.7 mW cm⁻² at 600 and 700 °C, respectively.     

In situ X-ray diffraction studies of mixed LiMn2O4-LiNi1/3Co1/3Mn1/3O2 composite cathode in Li-ion cells during charge-discharge cycling

The structural changes of the composite cathode made by mixing spinel LiMn₂O₄ and layered LiNi_1/3Co_1/3Mn_1/3O₂ in 1:1 wt% in both Li-half and Li-ion cells during charge/discharge are studied by in situ XRD. During the first charge up to ∼5.2 V vs. Li/Li⁺, the in situ XRD spectra for the composite cathode in the Li-half cell track the structural changes of each component. At the early stage of charge, the lithium extraction takes place in the LiNi_1/3Co_1/3Mn_1/3O₂ component only. When the cell voltage reaches at ∼4.0 V vs. Li/Li⁺, lithium extraction from the spinel LiMn₂O₄ component starts and becomes the major contributor for the cell capacity due to the higher rate capability of LiMn₂O₄. When the voltage passed 4.3 V, the major structural changes are from the LiNi_1/3Co_1/3Mn_1/3O₂ component, while the LiMn₂O₄ component is almost unchanged. In the Li-ion cell using a MCMB anode and a composite cathode cycled between 2.5 V and 4.2 V, the structural changes are dominated by the spinel LiMn₂O₄ component, with much less changes in the layered LiNi_1/3Co_1/3Mn_1/3O₂ component, comparing with the Li-half cell results. These results give us valuable information about the structural changes relating to the contributions of each individual component to the cell capacity at certain charge/discharge state, which are helpful in designing and optimizing the composite cathode using spinel- and layered-type materials for Li-ion battery research.     

Catalytic behavior of Ni/ZrxTi1−xO2 and the effect of SiO2 doping in oxidative steam reforming of n-butane

Catalytic behaviors of TiO₂-, Zr_0.5Ti_0.5O₂-, and ZrO₂-supported Ni catalysts were investigated for oxidative steam reforming of n-C₄H₁₀ at 723 K. The composite oxide support, Zr_0.5Ti_0.5O₂, shows high specific surface area (136 m²/g), leading to fine Ni particles. Thus, the Ni/Zr_0.5Ti_0.5O₂ catalyst exhibits higher and more stable activity than that exhibited by other catalysts. However, relatively large amounts of coke are deposited on the catalyst during reaction. Thus, to retard carbon deposition, the influence of SiO₂ additive was studied. Large amounts of SiO₂ additive (5 or 10 mol%) decrease initial activity; at 10 mol%, degradation is also induced by oxidation of Ni⁰. However, small amounts of SiO₂ additive (1.5 mol%) effectively retard coking without lowering initial activity. The resultant Ni/Zr_0.5Ti_0.5O₂–SiO₂ (1.5 mol%) catalyst exhibits high and stable activity without coking.     

Structure, morphology, and cathode performance of Li1−x[Ni0.5Mn1.5]O4 prepared by coprecipitation with oxalic acid

The cathode materials Li_1−x[Ni_0.5Mn_1.5]O₄ prepared by coprecipitation from acetate solution by oxalic acid and annealing at 900 °C in air had the preferred disordered Ni and Mn on the 16d octahedral sites of a spinel structure. The coprecipitation method provides better crystallinity than the phase previously obtained by quenching from the melt. Polycrystalline octahedral-shaped particles with smooth surfaces contained trace amounts of a Li_yNi_1−yO impurity that introduced some Mn(III) into the spinel phase. Half-cells cycled at 0.2 C rate between 3.5 and 4.8 V versus Li exhibited a flat voltage V ≈ 4.7 V with a small step at x ≈ 0.5 and a capacity at room temperature of 130 mAh g⁻¹ that showed no fade after 50 cycles. A small capacity fade was initiated with a cut-off voltage ≥4.9 V; a significant capacity loss between 2 and 5 C cycling rates was reversible to 134 mAh g⁻¹ on returning to 0.1 C after 50 cycles at 10 C between 3.5 and 5.0 V.     

Performance of LiNi0.5Mn1.5O4 prepared by solid-state reaction

LiNi_0.5Mn_1.5O₄ was prepared through a solid-state reaction using various Ni precursors. The effect of precursors on the electrochemical performance of LiNi_0.5Mn_1.5O₄ was investigated. LiNi_0.5Mn_1.5O₄ made from Ni(NO₃)₂·6H₂O shows the best charge–discharge performance. The reversible capacity of LiNi_0.5Mn_1.5O₄ is about 145 mAh g⁻¹ and remained 143 mAh g⁻¹ after 10 cycles at 3.0–5.0 V. The XRD results showed that the precursors and the dispersion methods had significant effect on their phase purity. Pure spinel phase can be obtained with high energy ball-milling method and Ni(NO₃)₂·6H₂O as precursor. Trace amount of NiO and Li₂MnO₃ phase were detected in LiNi_0.5Mn_1.5O₄ with manual-mixture method and using Ni(CH₃COO)₂·6H₂O, NiO and Ni₂O₃ as precursors.     

Effect of equivalent and non-equivalent Al substitutions on the structure and electrochemical properties of LiNi0.5Mn0.5O2

Pristine, equivalently and non-equivalently Al substituted LiNi_0.5Mn_0.5O₂ materials were prepared by a combination of co-precipitation and solid-state reaction. As shown by XRD and XPS, lattice volume shrinkage of LiNi_0.5(Mn_0.45Al_0.05)O₂ was attributed to the presence of Ni in both 2+ and 3+, while the lattice volume expansion of Li(Ni_0.45Al_0.05)Mn_0.5O₂ was caused by lowering the average oxidation state of Mn. Electrochemical performance of LiNi_0.5Mn_0.5O₂ materials can be greatly affected by the change of oxidation states of the transition metals by Al substitution. Non-equivalent substitution of Al for Ni leads to deteriorated discharge performance and cyclic stability due to the reduction of the electrochemical active Ni²⁺ and structure supported Mn⁴⁺, while an increase in the amount of Ni²⁺ in LiNi_0.5(Mn_0.45Al_0.05)O₂ brings obvious improvement of the electrochemical properties. EIS analyses of the electrode materials at pristine and charged states indicate that the poor electrochemical performance of Li(Ni_0.45Al_0.05)Mn_0.5O₂ material can be ascribed to the higher charge transfer resistance and surface film resistance, and the observed higher current rate capability of LiNi_0.5(Mn_0.45Al_0.05)O₂ can be understood due to the better charge transfer kinetics.     

Structural characteristics and electrochemical performance of layered Li[Mn0.5−xCr2xNi0.5−x]O2 cathode materials

Li[Mn_0.5−xCr_2xNi_0.5−x]O₂ (0 < 2x <0.2) (Mn/Ni = 1) cathode materials have been synthesized by a solution method. X-ray diffraction patterns of the as-prepared materials were fitted based on a hexagonal unit cell (α-NaFeO₂ layer structure). The extent of Li/Ni intermixing decreased, and layering of the structure increased, with increasing Cr content. Electrochemical cycling of the oxides, at 30 °C in the 3–4.3 V range vs. Li/Li⁺, showed that the first charge capacity increased with increasing Cr content. However, maximum discharge capacity (∼143 mAh g⁻¹) was observed for 2x = 0.05. X-ray absorption near edge spectroscopic (XANES) measurements on the K-edges of transition metals were carried out on pristine and delithiated oxides to elucidate the charge compensation mechanism during electrochemical charging. The XANES data revealed simultaneous oxidation of both Ni and Cr ions, whereas manganese remains as Mn⁴⁺ throughout, and does not participate in charge compensation during oxide delithiation.     

Electrochemical performance of spinel LiMn2O4 cathode materials made by flame-assisted spray technology

Spinel lithium manganese oxide LiMn₂O₄ powders were synthesized by a flame-assisted spray technology (FAST) with a precursor solution consisting of stoichiometric amounts of LiNO₃ and Mn(NO₃)₂·4H₂O dissolved in methanol. The as-synthesized LiMn₂O₄ particles were non-agglomerated, and nanocrystalline. A small amount of Mn₃O₄was detected in the as-synthesized powder due to the decomposition of spinel LiMn₂O₄ at the high flame temperature. The impurity phase was removed with a post-annealing heat-treatment wherein the grain size of the annealed powder was 33 nm. The charge/discharge curves of both powders matched the characteristic plateaus of spinel LiMn₂O₄ at 3 V and 4 V vs. Li. However, the annealed powder showed a higher initial discharge capacity of 115 mAh g⁻¹ at 4 V. The test cell with annealed powder showed good rate capability between a voltage of 3.0 and 4.3 V and a first cycle coulombic efficiency of 96%. The low coulombic efficiency from capacity fading may be due to oxygen defects in the annealed powder. The results suggest that FAST holds potential for rapid production of uniform cathode materials with low-cost nitrate precursors and minimal energy input.     

AlF3-coated LiCoO2 and Li[Ni1/3Co1/3Mn1/3]O2 blend composite cathode for lithium ion batteries

Surface modifications of electrode materials can improve the electrochemical and thermal properties of cathodes for use in lithium batteries. In this study, AlF₃-coated LiCoO₂ and AlF₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials are blended, as both have the same crystal structure and exhibit similar electrochemical properties. The composite electrodes exhibit high discharge capacities of 180-188 mAh g⁻¹ in a voltage range of 3.0-4.5 V at room temperature. The capacity retention of the composite electrode is greater than 95% of the initial capacity after 50 cycles. The thermal stability of these composite electrodes is greatly improved because of the superior thermal stability of AlF₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂. The blended AlF₃-coated LiCoO₂ and AlF₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ electrode shows two exothermic peaks, one at 227 °C from AlF₃-coated LiCoO₂ and another at 277 °C from AlF₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂, accompanied by significantly reduced exothermic heat generation.     

The electrochemical behaviour of the carbon-coated Ni0.5TiOPO4 electrode material

Ni_0.5TiOPO₄ oxyphosphate exhibits good electrochemical properties as an anode material in lithium ion batteries but suffers from its low conductivity. We present here the electrochemical performances of the synthesized Ni_0.5TiOPO₄/carbon composite by using sucrose as the carbon source. X-ray diffraction study confirms that this phosphate crystallizes in the monoclinic system (S.G. P2₁/c). The use of the Ni_0.5TiOPO₄/C composite in lithium batteries shows enhanced electrochemical performances compared with the uncoated material. Capacities up to 200 mAh g⁻¹ could be reached during cycling of this electrode. Furthermore, an acceptable rate capability was obtained with very low capacity fading even at 0.5C rate. Nevertheless, a considerable irreversible capacity was evidenced during the first discharge. In situ synchrotron X-ray radiation was utilized to study the structural change during the first discharge in order to evidence the origin of this irreversible capacity. Lithium insertion during the first discharge induces an amorphization of the crystal structure of the parent material accompanied by an irreversible formation of a new phase.     

Preparation and electrochemical properties of Li[Ni1/3Co1/3Mn1−x/3Zrx/3]O2 cathode materials for Li-ion batteries

Layer-structured Zr doped Li[Ni_1/3Co_1/3Mn_1−x/3Zr_x/3]O₂ (0 ≤ x ≤ 0.05) were synthesized via slurry spray drying method. The powders were characterized by XRD, SEM and galvanostatic charge/discharge tests. The products remained single-phase within the range of 0 ≤ x ≤ 0.03. The charge and discharge cycling of the cells showed that Zr doping enhanced cycle life compared to the bare one, while did not cause the reduction of the discharge capacity of Li[Ni_1/3Co_1/3Mn_1/3]O₂. The unchanged peak shape in the differential capacity versus voltage curve suggested that the Zr had the effect to stabilize the structure during cycling. More interestingly, the rate capability was greatly improved. The sample with x = 0.01 presented a capacity of 160.2 mAh g⁻¹ at current density of 640 mA g⁻¹(4 C), corresponding to 92.4% of its capacity at 32 mA g⁻¹(0.2 C). The favorable performance of the doped sample could be attributed to its increased lattice parameter.     

Structural and electrochemical characterization of xLi[Li1/3Mn2/3]O2·(1 − x)Li[Ni1/3Mn1/3Co1/3]O2 (0 ≤ x ≤ 0.9) as cathode materials for lithium ion batteries

A series of cathode materials with molecular notation of xLi[Li_1/3Mn_2/3]O₂·(1 − x)Li[Ni_1/3Mn_1/3Co_1/3]O₂ (0 ≤ x ≤ 0.9) were synthesized by combination of co-precipitation and solid state calcination method. The prepared materials were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques, and their electrochemical performances were investigated. The results showed that sample 0.6Li[Li_1/3Mn_2/3]O₂·0.4Li[Ni_1/3Mn_1/3Co_1/3]O₂ (x = 0.6) delivers the highest capacity and shows good capacity-retention, which delivers a capacity ∼250 mAh g⁻¹ between 2.0 and 4.8 V at 18 mA g⁻¹.     

An amorphous LiCo1/3Mn1/3Ni1/3O2 thin film deposited on NASICON-type electrolyte for all-solid-state Li-ion batteries

Amorphous LiCo_1/3Mn_1/3Ni_1/3O₂ thin films were deposited on the NASICON-type Li-ion conducting glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering below 130 °C. The amorphous films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The Li/PEO₁₈-Li(CF₃SO₂)₂N/LATSP/LiCo_1/3Mn_1/3Ni_1/3O₂/Au all-solid-state cells were fabricated to investigate the electrochemical performance of the amorphous films. It was found that the low-temperature deposited amorphous cathode film shows a high discharge voltage and a high discharge capacity of around 130 mAh g⁻¹.