Electrochemical profile of an asymmetric supercapacitor using carbon-coated LiTi2(PO4)3 and active carbon electrodes

In this work, we reported an asymmetric supercapacitor in which active carbon (AC) was used as a positive electrode and carbon-coated LiTi₂(PO₄)₃ as a negative electrode in 1 M Li₂SO₄ aqueous electrolyte. The LiTi₂(PO₄)₃/AC hybrid supercapacitor showed a sloping voltage profile from 0.3 to 1.5 V, at an average voltage near 0.9 V, and delivered a capacity of 30 mAh g⁻¹ and an energy density of 27 Wh kg⁻¹ based on the total weight of the active electrode materials. It exhibited a desirable profile and maintained over 85% of its initial energy density after 1000 cycles. The hybrid supercapacitor also exhibited an excellent rate capability, even at a power density of 1000 W kg⁻¹, it had a specific energy 15 Wh kg⁻¹ compared with 24 Wh kg⁻¹ at the power density about 200 W kg⁻¹.     

Hybrid supercapacitor based on MnO2 and columned FeOOH using Li2SO4 electrolyte solution

The nano-sized columned β-FeOOH was prepared by the hydrolysis process and its electrochemical capacitance performance was evaluated for the first time in Li₂SO₄ solution. A hybrid supercapacitor based on MnO₂ positive electrode and FeOOH negative electrode in Li₂SO₄ electrolyte solution was designed. The electrochemical tests demonstrated that the hybrid supercapacitor has a energy density of 12 Wh kg⁻¹ and a power density of 3700 W kg⁻¹ based on the total weight of the electrode active materials with a voltage range 0–1.85 V. This hybrid supercapacitor also exhibits a good cycling performance and keeps 85% of initial capacity over 2000 cycles.     

A cheap asymmetric supercapacitor with high energy at high power: Activated carbon//K0.27MnO2·0.6H2O

Studies of the electrochemical behavior of K_0.27MnO₂·0.6H₂O in K₂SO₄ show the reversible intercalation/deintercalation of K⁺-ions in the lattice. An asymmetric supercapacitor activated carbon (AC)/0.5 mol l⁻¹ K₂SO₄/K_0.27MnO₂·0.6H₂O was assembled and tested successfully. It shows an energy density of 25.3 Wh kg⁻¹ at a power density of 140 W kg⁻¹; at the same time it keeps a very good rate behavior with an energy density of 17.6 Wh kg⁻¹ at a power density of 2 kW kg⁻¹ based on the total mass of the active electrode materials, which is higher than that of AC/0.5 mol l⁻¹ Li₂SO₄/LiMn₂O₄. In addition, this asymmetric supercapacitor shows excellent cycling behavior without the need to remove oxygen from the electrolyte solution. This can be ascribed in part to the stability of the lamellar structure of K_0.27MnO₂·0.6H₂O. This asymmetric aqueous capacitor has great promise for practical applications due to high energy density at high power density.     

Graphene-MnO2 and graphene asymmetrical electrochemical capacitor with a high energy density in aqueous electrolyte

The graphene-manganese oxide hybrid material has been prepared by solution-phase assembly of aqueous dispersions of graphene nanosheets and manganese oxide nanosheets at room temperature. The morphology and structure of the obtained material are examined by scanning electron microscopy, transition electron microscopy, X-ray diffraction and N₂ adsorption-desorption. Electrochemical properties are characterized by cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy. An asymmetric electrochemical capacitor with high energy and power densities based on the graphene-manganese oxide hybrid material as positive electrode and graphene as negative electrode in a neutral aqueous Na₂SO₄ solution as electrolyte is assembled. The asymmetrical electrochemical capacitor could cycle reversibly in a voltage of 0-1.7 V and give an energy density of 10.03 Wh kg⁻¹ even at an average power density of 2.53 kW kg⁻¹. Moreover, the asymmetrical electrochemical capacitor exhibit excellent cycle stability, and the capacitance retention of the asymmetrical electrochemical capacitor is 69% after repeating the galvanostatic charge-discharge test at the constant current density of 2230 mA g⁻¹ for 10,000 cycles.     

Electrodeposition and pseudocapacitive properties of tungsten oxide/polyaniline composite

Composite films of tungsten oxide (WO₃) and polyaniline (PANI) have been electrodeposited by cyclic voltammetry in a mixed solution of aniline and precursor of tungsten oxide. Surface morphology and chemical composition of WO₃/PANI composite are characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The influence of H₂O₂ on the electrodeposition of WO₃/PANI composite film is also investigated. Cyclic voltammetry (CV), chronopotentiometry (CP) and electrochemical impedance spectroscopy (EIS) results show that WO₃/PANI composite film exhibit good pseudocapacitive performance over a wide potential range of −0.5 to 0.7 V vs. SCE with the specific capacitance of 168 F g⁻¹ at current density of 1.28 mA cm⁻² and energy density of 33.6 Wh kg⁻¹, which is 91% higher than that of similarly prepared PANI (17.6 Wh kg⁻¹). An asymmetric model capacitor using WO₃/PANI as negative and PANI as positive electrodes over voltage range of 1.2 V displays a specific capacitance of 48.6 F g⁻¹ and energy density of 9.72 Wh kg⁻¹ at the power density of 53 W kg⁻¹, which is two times higher than that of a symmetric capacitor modeled by using two PANI films as both positive and negative electrodes.     

High energy density PbO2/activated carbon asymmetric electrochemical capacitor based on lead dioxide electrode with three-dimensional porous titanium substrate

A PbO₂/AC asymmetric electrochemical capacitor (AEC) with energy density as high as 49.4 Wh kg⁻¹, power density of 433.2 W kg⁻¹ and specific capacitance of 135.2 F g⁻¹ was fabricated with PbO₂ electrodeposited on three-dimensional porous titanium (3D-Ti/PbO₂) and activated carbon. The high electrochemical active surface of 3D-Ti/PbO₂ resulted in high specific capacity making it suitable for use as positive electrode in PbO₂/AC AEC. The fabricated AEC demonstrated good power performance with an energy density conservation of 30 Wh kg⁻¹ at power density of 2078 W kg⁻¹. The fabricated AEC also showed excellent cycling stability with capacitance retention of 99.2% after 1000 cycles.     

High-energy density graphite/AC capacitor in organic electrolyte

A high-energy density hybrid capacitor has been designed in organic electrolyte (1 mol L⁻¹ LiPF₆ in 1:1 ethylene carbonate (EC)/dimethyl carbonate (DMC)) using commercial grades of graphite and activated carbon for negative and positive electrodes, respectively. Different approaches have been explored for assembling the hybrid capacitor in order to achieve an optimum ratio between the energy and power density, while keeping a long cycle-life capability. In the optimized hybrid capacitor, the potential of the positive electrode ranges from 1.5 up to 5 V vs. Li/Li⁺, being extended to the whole stability window of the activated carbon in the organic electrolyte, whereas the potential of the negative electrode remains almost constant at around 0.1 V vs. Li/Li⁺. After balancing carefully the respective masses of the electrodes and appropriately formatting the system, it was found that a voltage of 4.5 V is the optimal value for avoiding a capacitance fading of the hybrid capacitor during cycling. Gravimetric and volumetric energy densities as high as 103.8 Wh kg⁻¹ and 111.8 Wh L⁻¹, respectively, were obtained. The noticeable value of volumetric energy density is 10 times higher than for symmetric or asymmetric capacitors built with the same activated carbon.     

Hybrid supercapacitor with nano-TiP2O7 as intercalation electrode

Nano-size (≤100 nm) TiP₂O₇ is prepared by the urea assisted combustion synthesis, at 450 and 900 °C. The compound is characterized by powder X-ray diffraction, Rietveld refinement, high resolution transmission electron microscopy and surface area methods. Lithium cycling properties by way of galvanostatic cycling and cyclic voltammetry (CV) showed a reversible and stable capacity of 60 (±3) mAh g⁻¹ (0.5 mole of Li) up to 100 cycles, when cycled at 15 mA g⁻¹ between 2-3.4 V vs. Li. Non-aqueous hybrid supercapacitor, TiP₂O₇ (as anode) and activated carbon (AC) (as cathode) has been studied by galvanostatic cycling and CV in the range, 0-3 V at 31 mA g⁻¹ and exhibited a specific discharge capacitance of 29 (±1) F g⁻¹stable in the range, 100-500 cycles. The Ragone plot shows a deliverable maximum of 13 Wh kg⁻¹ and 371 W kg⁻¹ energy and power density, respectively.     

Intercalation of PF6 anion into graphitic carbon with nano pore for dual carbon cell with high capacity

Intercalation property of PF₆⁻ into graphitic carbon was studied for a hybrid capacitor with different ratio of cathode and anode amount. Graphene sheet distance increased with increasing PF₆⁻ intercalation amount and it saturated at 0.4 nm at high applied potential, which is corresponded to stage 2 structure. On the other hand, it was found that nano size pore into graphene sheet was introduced at higher applied potential with 20 times larger anode carbon and this nano porous carbon shows a large capacity for intercalation capacity of 147 mAh g⁻¹. The estimated energy density of the hybrid capacitor using carbon with nano bubble structure was ca. 400 Wh kg⁻¹.     

Enhancement of the energy storage properties of supercapacitors using graphene nanosheets dispersed with metal oxide-loaded carbon nanotubes

Graphene nanosheets (GNs) dispersed with SnO₂ nanoparticles loaded multiwalled carbon nanotubes (SnO₂-MWCNTs) were investigated as electrode materials for supercapacitors. SnO₂-MWCNTs were obtained by a chemical method followed by calcination. GNs/SnO₂-MWCNTs nanocomposites were prepared by ultrasonication of the GNs and SnO₂-MWCNTs. Electrochemical double layer capacitors were fabricated using the composite as the electrode material and aqueous KOH as the electrolyte. Electrochemical performance of the composite electrodes were compared to that of pure GNs electrodes and the results are discussed. Electrochemical measurements show that the maximum specific capacitance, power density and energy density obtained for supercapacitor using GNs/SnO₂-MWCNTs nanocomposite electrodes were respectively 224 F g⁻¹, 17.6 kW kg⁻¹ and 31 Wh kg⁻¹. The fabricated supercapacitor device exhibited excellent cycle life with ∼81% of the initial specific capacitance retained after 6000 cycles. The results suggest that the hybrid composite is a promising supercapacitor electrode material.     

Electrochemical supercapacitor behavior of Ni3(Fe(CN)6)2(H2O) nanoparticles

Nanosized Ni₃(Fe(CN)₆)₂(H₂O) was prepared by a simple co-precipitation method. The electrochemical properties of the sample as the electrode material for supercapacitor were studied by cyclic voltammetry (CV), constant charge/discharge tests and electrochemical impedance spectroscopy (EIS). A specific capacitance of 574.7 F g⁻¹ was obtained at the current density of 0.2 A g⁻¹ in the potential range from 0.3 V to 0.6 V in 1 M KNO₃ electrolyte. Approximately 87.46% of specific discharge capacitance was remained at the current density of 1.4 A g⁻¹ after 1000 cycles.     

Asymmetric capacitor based on superior porous Ni-Zn-Co oxide/hydroxide and carbon electrodes

Hierarchical porous multi-phase Ni-Zn-Co oxide/hydroxide is synthesized by using metal-organic framework-5 (MOF-5) as the template. Hierarchical porous carbon is obtained by the facile direct decomposition of the MOF-5 framework with phenolic resin. The structures and textures are characterized by X-ray diffraction, high-resolution transmission electron microscopy, scanning electron microscopy, and nitrogen sorption at 77 K. An asymmetric capacitor incorporating the Ni-Zn-Co oxide/hydroxide as the positive electrode and the porous carbon as the negative electrode is fabricated. A maximum energy density of 41.65 Wh kg⁻¹ is obtained, which outperforms many other available asymmetric capacitors. The asymmetric capacitor also shows a good high-rate performance, possessing an energy density of 16.62 Wh kg⁻¹ at the power density of about 2900 W kg⁻¹.     

Characterization of MnFe2O4/LiMn2O4 aqueous asymmetric supercapacitor

A new type of asymmetric supercapacitor containing a MnFe₂O₄ negative electrode and a LiMn₂O₄ positive electrode in aqueous LiNO₃ electrolyte has been synthesized and characterized. The nanocrystalline MnFe₂O₄ anode material has a specific capacitance of 99 F g⁻¹ and the LiMn₂O₄ cathode a specific capacity of 130-100 mAh g⁻¹ under 10-100 C rate. The cell has a maximum operating voltage window of ca. 1.3 V, limited by irreversible reaction of MnFe₂O₄ toward reducing potential. The specific power and specific energy of the full-cell increase with increasing anode-to-cathode mass ratio (A/C) and saturate at A/C ∼4.0, which gives specific cell energies, based on total mass of the two electrodes, of 10 and 5.5 Wh kg⁻¹ at 0.3 and 1.8 kW kg⁻¹, respectively. The cell shows good cycling stability and exhibits significantly slower self-discharge rate than either the MnFe₂O₄ symmetric cell or the other asymmetric cells having the same cathode but different anode materials, including activated carbon fiber and MnO₂.     

A new cheap asymmetric aqueous supercapacitor: Activated carbon//NaMnO2

A new cheap asymmetric supercapacitor based on activated carbon (AC) and NaMnO₂ as electrodes and aqueous Na₂SO₄ solution as electrolyte was assembled. It shows an energy density of 19.5 Wh kg⁻¹ at a power density of 130 W kg⁻¹ based on the total mass of the active electrode materials and an excellent cycling behavior. This asymmetric aqueous AC//NaMnO₂ capacitor is promising for practical applications due to its low price, easy preparation of NaMnO₂ and friendliness to environment.     

Electrochemically synthesized nanocrystalline spinel thin film for high performance supercapacitor

Spinels are not known for their supercapacitive nature. Here, we have explored electrochemically synthesized nanostructured NiCo₂O₄ spinel thin-film electrode for electrochemical supercapacitors. The nanostructured NiCo₂O₄ spinel thin film exhibited a high specific capacitance value of 580 F g⁻¹ and an energy density of 32 Wh kg⁻¹ at the power density of 4 kW kg⁻¹, accompanying with good cyclic stability.     

Supercapacitive properties of hybrid films of manganese dioxide and polyaniline based on active carbon in organic electrolyte

This is the first report about supercapacitive performance of hybrid film of manganese dioxide (MnO₂) and polyaniline (PANI) in an organic electrolyte (1.0 M LiClO₄ in acetonitrile). In this work, a high surface area and conductivity of active carbon (AC) electrode is used as a substrate for PANI/MnO₂ film electro-codeposition. The redox properties of the coated PANI/MnO₂ thin film exhibit ideal capacitive behaviour in 1 M LiClO₄/AN. The specific capacitance (SC) of PANI/MnO₂ hybrid film is as high as 1292 F g⁻¹ and maintains about 82% of the initial capacitance after 1500 cycles at a current density of 4.0 mA cm⁻², and the coulombic efficiency (η) is higher than 95%. An asymmetric capacitor has been developed with the PANI/MnO₂/AC positive and pure AC negative electrodes, which is able to deliver a specific energy as high as 61 Wh kg⁻¹ at a specific power of 172 W kg⁻¹ in the range of 0-2.0 V. These results indicate that the organic electrolyte is a promising candidate for PANI/MnO₂ material application in supercapacitors.     

A dye-sensitized photo-supercapacitor based on PProDOT-Et2 thick films

A photo-rechargeable supercapacitor (photo-supercapacitor, or PSC) is studied using a N3-dye adsorbed TiO₂ photoelectrode and PProDOT-Et₂ poly(3,3-diethyl-3,4-dihydro-2H-thieno-[3,4-b][1,4]dioxepine) polymer films as supercapacitor materials for electron storage. The PSC device, comprising a dye-sensitized solar cell (DSSC) and a supercapacitor (SC), can store the photo-to-electric energy. The PProDOT-Et₂ films are potentiostatically electropolymerized to form thick films (ca. 0.5 mm) with a specific capacitance of ca. 6.5 F cm⁻². A symmetrical (p/p) supercapacitor, with PProDOT-Et₂ coated on both electrodes, is also characterized before fabricating the three-electrode PSC. The PSC is tested under light illumination of 100 mW cm⁻², and attaining a photocharged voltage of 0.75 V and a discharged energy density of 21.3 μWh cm⁻².     

Dual functions of activated carbon in a positive electrode for MnO2-based hybrid supercapacitor

Utilizing the dual functions of activated carbon (AC) both as a conductive agent and an active substance of a positive electrode, a hybrid supercapacitor (AC-MnO₂&AC) with a composite of manganese dioxide (MnO₂) and activated carbon as the positive electrode (MnO₂&AC) and AC as the negative electrode is fabricated, which integrates approximate symmetric and asymmetric behaviors in the distinct parts of 2 V operating windows. MnO₂ in the positive electrode and AC in the negative electrode together form a pure asymmetric structure, which extends the operating voltage to 2 V due to the compensatory effect of opposite over-potentials. In the range of 0-1.1 V, both AC in the positive and negative electrode assemble as a symmetric structure via a parallel connection which offers more capacitance and less internal resistance. The optimal mass proportions of electrodes are calculated though a mathematical process. In a stable operating window of 2 V, the capacitance of AC-MnO₂&AC can reach 33.2 F g⁻¹. After 2500 cycles, maximum energy density is 18.2 Wh kg⁻¹ with a 4% loss compared to the initial cycle. The power density is 10.1 kW kg⁻¹ with an 8% loss.     

High energy density capacitor using coal tar pitch derived nanoporous carbon/MnO2 electrodes in aqueous electrolytes

Asymmetric aqueous electrochemical capacitors with energy densities as high as 22 Wh kg⁻¹, power densities of 11 kW kg⁻¹ and a cell voltage of 2 V were fabricated using cost effective, high surface carbon derived from coal tar pitch and manganese dioxide. The narrow pore size distribution of the activated carbon (mean pore size ∼0.8 nm) resulted in strong electroadsorption of protons making them suitable for use as negative electrodes. Amorphous manganese dioxide anodes were synthesized by chemical precipitation method with high specific capacitance (300 F g⁻¹) in aqueous electrolytes containing bivalent cations. The fabricated capacitors demonstrated excellent cyclability with no signs of capacitance fading even after 1000 cycles.     

Electrochemical micro-capacitors of patterned electrodes loaded with manganese oxide and carbon nanotubes

MnO₂ and carbon nanotubes (CNT) composite electrodes have been built on the interdigital stack layers of Fe-Al/SiO₂ and Fe-Al/Au/Ti/SiO₂ for the electrochemical micro-capacitors, using photolithography and thin-film technologies. The electrode properties and the performance of micro-cells are measured and analyzed with cyclic voltammetry (CV), impedance spectroscopy, and galvanostatic charge/discharge test in 0.1 M Na₂SO₄ electrolyte. The vertically aligned CNT, grown on Fe-Al/SiO₂, is more suitable for supporting the pseudocapacitive MnO₂ than the random CNT on Fe-Al/Au/Ti/SiO₂, but ohmic resistance of the former electrode is higher. We have prepared three cells on each stack layer with different electrode materials. The Ragone plot shows systematic variations in power and energy performance, reflecting their differences in electrode structure and polarization loss. The asymmetric cell of a pseudocapacitive positive electrode, loaded with MnO₂ and CNT, exhibits a small IR drop and a high specific energy during discharge. Built on Fe-Al/SiO₂, this asymmetric cell discharges at specific power 0.96 kW kg⁻¹ with specific energy 10.3 Wh kg⁻¹; while on Fe-Al/Au/Ti/SiO₂, the asymmetric cell discharges at power 1.16 kW kg⁻¹ with energy 5.71 Wh kg⁻¹.