Carbon coatings with olive oil,soybean oil and butter on nano-LiFePO4

Kitchen oils (olive, soybean and butter) are selected for carbon coatings on LiFePO₄. The surface properties of LiFePO₄ are unknown or vary depending on synthetic methods. The multi-functional groups of fatty acids in the oils can orient properly to cope with the variable surface properties of LiFePO₄, which can lead to dense carbon coatings. The low price and low toxicity of kitchen oils are other advantages of the coating process. LiFePO₄ (D₅₀ = 121 nm)combined with the carbon coating enhances the rate capability. Capacities at the 2C rate reach 150 mAh g⁻¹ or higher. The charge retention values of 2.0C/0.2C are between 94.4 and 98.9%.     

A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Cathode performance of olivine-type LiFePO4 synthesized by chemical lithiation

Chemical lithiation with LiI in acetonitrile was performed for amorphous FePO₄ synthesized from an equimolar aqueous suspension of iron powder and an aqueous solution of P₂O₅. An orthorhombic LiFePO₄ olivine structure was obtained by annealing a chemically lithiated sample at 550 °C for 5 h in Ar atmosphere. The average particle size remained at approximately 250 nm even after annealing. The lithium content in the sample was quantitatively confirmed by Li atomic absorption analysis and ⁵⁷Fe Mössbauer spectroscopy. While an amorphous FePO₄/carbon composite cathode has a monotonously decreasing charge–discharge profile with a reversible capacity of more than 140 mAh g⁻¹, the crystallized LiFePO₄/carbon composite shows a 3.4 V plateau corresponding to a two-phase reaction. This means that the lithium in the chemically lithiated sample is electrochemically active. Both amorphous FePO₄ and the chemically lithiated and annealed crystalline LiFePO₄ cathode materials showed good cyclability (more than 140 mAh g⁻¹ at the 40th cycle) and good discharge rate capability (more than 100 mAh g⁻¹ at 5.0 mA cm⁻²). In addition, the fast-charge performance was found to be comparable to that with LiCoO₂.     

Surfactant based sol–gel approach to nanostructured LiFePO4 for high rate Li-ion batteries

Porous nanostructured LiFePO₄ powder with a narrow particle size distribution (100–300 nm) for high rate lithium-ion battery cathode application was obtained using an ethanol based sol–gel route employing lauric acid as a surfactant. The synthesized LiFePO₄ powders comprised of agglomerates of crystallites <65 nm in diameter exhibiting a specific surface area ranging from 8 m² g⁻¹ to 36 m² g⁻¹ depending on the absence or presence of the surfactant. The LiFePO₄ obtained using lauric acid resulted in a specific capacity of 123 mAh g⁻¹ and 157 mAh g⁻¹ at discharge rates of 10C and 1C with less than 0.08% fade per cycle, respectively. Structural and microstructural characterization were performed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) with energy dispersive X-ray (EDX) analysis while electronic conductivity and specific surface area were determined using four-point probe and N₂ adsorption techniques.     

Morphological characterization of LiFePO4/C composite cathode materials synthesized via a carboxylic acid route

A new type of LiFePO₄/C composite surrounded by a web containing both amorphous and crystalline carbon phases was synthesized by incorporating malonic acid as a carbon source using a high temperature solid-state method. SEM, TEM/SAED/EDS and HRTEM were used to analyze surface morphology and confirmed for the first time that crystalline carbon was present in LiFePO₄/C composites. The composite was effective in enhancing the electrochemical properties such as capacity and rate capability, because its active component consists of nanometer-sized particles containing pores with a wide range of sizes. An EDS elemental map showed that carbon was uniformly distributed on the surface of the composite crystalline particles. TEM/EDS results clearly show a dark region that is LiFePO₄ with a trace of carbon and a gray region that is carbon only. To evaluate the materials’ electrochemical properties, galvanostatic cycling and conductivity measurements were performed. The best cell performance was delivered by the material coated with 60 wt.% malonic acid, which delivered first cycle discharge capacity of 149 mAh g⁻¹ at a C/5 rate and sustained 222 cycles at 80% of capacity retention. When carboxylic acid was used as a carbon source to produce LiFePO₄, overall conductivity increased from 10⁻⁵ to 10⁻⁴ S cm⁻¹, since particle growth was prevented during the final sintering process.     

A simple,cheap soft synthesis routine for LiFePO4 using iron(III) raw material

An order olivine structure LiFePO₄ was synthesized with a simple rheological phase reaction (RPR) of LiOH·H₂O and FePO₄·4H₂O in the presence of PEG as a reductive agent and carbon source. A required amount of water was added to the starting materials to form the rheological precursor and decomposed at 700 °C to form the crystalline phase LiFePO₄ directly, without ball-milling, preparation of intermediates, pre-sintering and post-deposition treatment. Fine particles with an average particle size about 216 nm are examined by scanning electron microscopy (SEM) and optical particle size analyzer. An initial discharge capacity of 157 mAh g⁻¹ was achieved for the as-prepared LiFePO₄ material with a rate of 0.1C (17 mA g⁻¹), what's more, this material shows excellent specific capacity, charge–discharge efficiency and cycle efficiency at high current rates, almost no capacity loss can be observed up to 40 cycles with the rate of 1, 2 and 3C at room temperature. The simple, cheap process as well as the excellent high-rate performance makes this RPR method feasible commercially.     

Synthesis and electrochemical performance of the high voltage cathode material Li[Li0.2Mn0.56Ni0.16Co0.08]O2 with improved rate capability

The high voltage layered Li[Li_0.2Mn_0.56Ni_0.16Co_0.08]O₂ cathode material, which is a solid solution between Li₂MnO₃ and LiMn_0.4Ni_0.4Co_0.2O₂, has been synthesized by co-precipitation method followed by high temperature annealing at 900 °C. XRD and SEM characterizations proved that the as prepared powder is constituted of small and homogenous particles (100-300 nm), which are seen to enhance the material rate capability. After the initial decay, no obvious capacity fading was observed when cycling the material at different rates. Steady-state reversible capacities of 220 mAh g⁻¹ at 0.2C, 190 mAh g⁻¹ at 1C, 155 mAh g⁻¹ at 5C and 110 mAh g⁻¹ at 20C were achieved in long-term cycle tests within the voltage cutoff limits of 2.5 and 4.8 V at 20 °C.     

High voltage spinel cathode materials for high energy density and high rate capability Li ion rechargeable batteries

We have synthesized LiMn_1.5Ni_0.4Cr_0.1O₄ cathode material for high energy density Li ion rechargeable batteries using sol-gel method. The synthesized materials were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy, cyclic voltammetry and charge-discharge characteristics. It was found that phase pure materials were obtained an annealing temperature of 875 °C for 15 h. The maximum discharge capacity at a constant charge-discharge current rate 1C, 0.5C, and 0.2C were found to be about 99 mAh g⁻¹, 110 mAh g⁻¹, and 131 mAh g⁻¹, respectively. The capacity retentions after 50 charge-discharge cycles were found to be about 99%, 97%, and 97.3% at discharge current rates of 0.2C, 0.5C, and 1C. The stable electrochemical behavior of the above cathode material even at high C rate, showed that it could be used for high energy density and high rate capability Li ion rechargeable batteries.     

The effect of carbon coating thickness on the capacity of LiFePO4/C composite cathodes

Two types of carbon source and precursor mixing pellets were employed simultaneously to prepare the LiFePO₄/C composite materials: Type I using the LiFePO₄ precursor with 20 wt.% polystyrene (PS) as a primary carbon source, and Type II using the LiFePO₄ precursor with 50 wt.% malonic acid as a secondary carbon vapor source. During final sintering, a Type I pellet was placed down-stream and Type II precursor pellet(s) was(were) placed upstream next to a Type I precursor pellet in a quartz-tube furnace. The carbon-coated product of the sintered Type I precursor pellet was obtained by using both PS and malonic acid as carbon sources. When two Type II pellets were used as a carbon vapor source (defined as Product-2), a more uniform film between 4 and 8 nm was formed, as shown in the TEM images. In the absence of a secondary carbon source (defined as Product-0), the discharge capacity of Product-0 was 137 mAh g⁻¹ with 100 cycles at a 0.2C-rate, but Product-2 demonstrated a high capacity of 151 mAh g⁻¹ with 400 cycles. Our results indicate that electrochemical properties of LiFePO₄ are correlated to the amount of carbon and its coating thickness and uniformity.     

Electrochemical properties of LiFe0.9Mn0.1PO4/Fe2P cathode material by mechanical alloying

LiFePO₄, olivine-type LiFe_0.9Mn_0.1PO₄/Fe₂P composite was synthesized by mechanical alloying of carbon (acetylene back), M₂O₃ (M = Fe, Mn) and LiOH·H₂O for 2 h followed by a short-time firing at 900 °C for only 30 min. By varying the carbon excess different amounts of Fe₂P second phase was achieved. The short firing time prevented grain growth, improving the high-rate charge/discharge capacity. The electrochemical performance was tested at various C/x-rate. The discharge capacity at 1C rate was increased up to 120 mAh g⁻¹ for the LiFe_0.9Mn_0.1PO₄/Fe₂P composite, while that of the unsubstituted LiFePO₄/Fe₂P and LiFePO₄ showed only 110 and 60 mAh g⁻¹, respectively. Electronic conductivity and ionic diffusion constant were measured. The LiFe_0.9Mn_0.1PO₄/Fe₂P composite showed higher conductivity and the highest diffusion coefficient (3.90 × 10⁻¹⁴ cm² s⁻¹). Thus the improvement of the electrochemical performance can be attributed to (1) higher electronic conductivity by the formation of conductive Fe₂P together with (2) an increase of Li⁺ ion mobility obtained by the substitution of Mn²⁺ for Fe²⁺.     

Electrochemical performance of mesoporous TiO2 anatase

Mesoporous TiO₂ was prepared via a sol–gel method from an ethylene glycol-based titanium-precursor in the presence of a non-ionic surfactant at pH 2. Only the anatase structure was detected after annealing, while the BET specific surface area was measured as being 90 m² g⁻¹ with a rather monomodal pore diameter close to 5 nm. Electrochemical performances were investigated by cyclic voltammetry and galvanostatic techniques. Mesoporous TiO₂ exhibits excellent rate capability (184 mAh g⁻¹ at C/5, 158 mAh g⁻¹ at 2C, 127 mAh g⁻¹ at 6C, and 95 mAh g⁻¹ at 30C) and good cycling stability.     

Hydrothermal preparation of LiFePO4 nanocrystals mediated by organic acid

Well-crystallized LiFePO₄ nanoparticles have been directly synthesized in a short time via hydrothermal process in the presence of organic acid, e.g. citric acid or ascorbic acid. These acid-mediated LiFePO₄ products exhibit a phase-pure and nanocrystal nature with size about 50-100 nm. Two critical roles that the organic acid mediator plays in hydrothermal process are recognized and a rational mechanism is explored. After a post carbon-coating treatment at 600 °C for 1 h, these mediated LiFePO₄ materials show a high electrochemical activity in terms of reversible capacity, cycling stability and rate capability. Particularly, LiFePO₄ mediated by ascorbic acid can deliver a capacity of 162 mAh g⁻¹ at 0.1 C, 154 mAh g⁻¹ at 1 C, and 122 mAh g⁻¹ at 5 C. The crystalline structure, particle morphology, and surface microstructure were characterized by high-energy synchrotron X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), and Raman spectroscopy, respectively. And the electrochemical properties were thoroughly investigated by galvanostatic test and electrochemical impedance spectroscopy (EIS).     

Preparation of LiFePO4/C composites by co-precipitation in molten stearic acid

The olivine type LiFePO₄ is synthesized via a simple and inexpensive route by aqueous co-precipitation of an Fe(II) precursor material in molten stearic acid and subsequent heat treatment at different temperatures. Stearic acid serves as both chelating agent and carbonaceous material. The obtained composites with carbon are characterized by X-ray powder diffraction, field emission scanning electron microscopy, and Mössbauer spectroscopy. Electrochemical characteristics of the composites are evaluated by using galvanostatic charge/discharge tests. The powder obtained at 700 °C delivers discharge capacity of 160 mAh g⁻¹, quite near the theoretical value.     

LiFePO4 and graphite electrodes with ionic liquids based on bis(fluorosulfonyl)imide (FSI) for Li-ion batteries

Ambient-temperature ionic liquids (IL) based on bis(fluorosulfonyl)imide (FSI) as anion and 1-ethyl-3-methyleimidazolium (EMI) or N-methyl-N-propylpyrrolidinium (Py13) as cations have been investigated with natural graphite anode and LiFePO₄ cathode in lithium cells. The electrochemical performance was compared to the conventional solvent EC/DEC with 1 M LiPF₆ or 1 M LiFSI. The ionic liquid showed lower first coulombic efficiency (CE) at 80% compared to EC–DEC at 93%. The impedance spectroscopy measurements showed higher resistance of the diffusion part and it increases in the following order: EC–DEC–LiFSI < EC–DEC–LiPF₆ < Py13(FSI)–LiFSIE = MI(FSI)–LiFSI. On the cathode side, the lower reversible capacity at 143 mAh g⁻¹ was obtained with Py13(FSI)–LiFSI; however, a comparable reversible capacity was found in EC–DEC and EMI(FSI)–LiFSI. The high viscosity of the ionic liquids suggests that different conditions such as vacuum and 60 °C are needed to improve impregnation of IL in the electrodes. With these conditions, the reversible capacity improved to 160 mAh g⁻¹ at C/24. The high-rate capability of LiFePO₄ was evaluated in polymer–IL and compared to the pure IL cells. The reversible capacity at C/10 decreased from 155 to only 126 mAh g⁻¹ when the polymer was present.     

Enhancement of electrochemical performance of lithium dry polymer battery with LiFePO4/carbon composite cathode

LiFePO₄/carbon composite electrode was prepared and applied to the dry polymer electrolyte. Enhanced low-temperature performance of LiFePO₄ was achieved by modifying the interface between LiFePO₄ and polymer electrolyte. The molecular weight of the polymer and the salt concentration as the Li/O ratio were optimized at 3 × 10⁵ and 1/10, respectively. Impedance analysis revealed that a small resistive component occurred in the frequency range of the charge transfer process. The reversible capacity of the laminate cell was 140 mAh g⁻¹ (C/20) and 110 mAh g⁻¹ (C/2) at 40 °C, which is comparable to the performance in the liquid electrolyte system.     

Synthesis and characterization of Carbon Nano Fiber/LiFePO4 composites for Li-ion batteries

Carbon Nano Fibers (CNFs) coated with LiFePO₄ particles have been prepared by a non-aqueous sol–gel technique. The functionalization of the CNFs by HNO₃ acid treatment has been confirmed by Raman and XPS analyses. The samples pure LiFePO₄ and LiFePO₄–CNF have been characterized by XRD, SEM, RAMAN, XPS and electrochemical analysis. The LiFePO₄–CNF sample shows better electrochemical performance compared to as-prepared LiFePO₄. LiFePO₄–CNF (10 wt.%) delivers a higher specific capacity (∼140 mAh g⁻¹) than LiFePO₄ with carbon black (25 wt.%) added after synthesis (∼120 mAh g⁻¹) at 0.1C.     

A novel sol-gel method based on FePO4·2H2O to synthesize submicrometer structured LiFePO4/C cathode material

Carbon coated LiFePO₄/C cathode material is synthesized with a novel sol-gel method, using cheap FePO₄·2H₂O as both iron and phosphorus sources and oxalic acid (H₂C₂O₄·2H₂O) as both complexant and reductant. In H₂C₂O₄ solution, FePO₄·2H₂O is very simple to form transparent sols without controlling the pH value. Pure submicrometer structured LiFePO₄ crystal is obtained with a particle size ranging from 100 to 500 nm, which is also uniformly coated with a carbon layer, about 2.6 nm in thickness. The as-synthesized LiFePO₄/C sample exhibits high initial discharge capacity 160.5 mAh g⁻¹ at 0.1 C rate, with a capacity retention of 98.7% after 50th cycle. The material also shows good high-rate discharge performances, about 106 mAh g⁻¹ at 10 C rate. The improved electrochemical properties of as-synthesized LiFePO₄/C are ascribed to its submicrometer scale particles and low electrochemical impedance. The sol-gel method may be of great interest in the practical application of LiFePO₄/C cathode material.     

Effects of magnesium doping on electronic conductivity and electrochemical properties of LiFePO4 prepared via hydrothermal route

Carbon free composites Li_1−xMg_xFePO₄ (x = 0.00, 0.02) were synthesized from LiOH, H₃PO₄, FeSO₄ and MgSO₄ through hydrothermal route at 180 °C for 6h followed by being fired at 750 °C for 6 h. The samples were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), flame atomic absorption spectroscopy and electronic conductivity measurement. To investigate their electrochemical properties, the samples were mixed with glucose as carbon precursors, and fired at 750 °C for 6 h. The charge–discharge curves and cycle life test were carried out at 23 ± 2 °C. The Rietveid refinement results of lattice parameters of the samples indicate that the magnesium ion has been successfully doped into the M1 (Li) site of the phospho-olivine structure. With the same order of magnitude, there is no material difference in terms of the electronic conductivities between the doped and undoped composites. Conductivities of the doped and undoped samples are 10⁻¹⁰ S cm⁻¹ before being fired, 10⁻⁹ S cm⁻¹ after being fired at 750 °C, and 10⁻¹ S cm⁻¹ after coated with carbon, respectively. Both the doped and undoped composites coated with carbon exhibit comparable specific capacities of 146 mAh g⁻¹ vs. 144 mAh g⁻¹ at 0.2 C, 140 mAh g⁻¹ vs. 138 mAh g⁻¹ at 1 C, and 124 mAh g⁻¹ vs. 123 mAh g⁻¹ at 5 C, respectively. The capacity retention rates of both doped and undoped samples over 50 cycles at 5 C are close to 100% (vs. the first-cycle corresponding C-rate capacity). Magnesium doping has little effects on electronic conductivity and electrochemical properties of LiFePO₄ composites prepared via hydrothermal route.     

Effects of carbon coating and iron phosphides on the electrochemical properties of LiFePO4/C

Carbon coated LiFePO₄ (LiFePO₄/C) with different contents of high electron conductive iron phosphide phase was synthesized by an aqueous sol–gel method in a reductive sintering atmosphere. Different synthesis parameters were used for adjusting the microstructure and phase compositions of the products. The effects of the carbon coating and iron phosphides on the electrochemical properties of the LiFePO₄/C electrodes were studied by means of testing the discharge capacities at rates of 0.1–5C (1C = 170 mAh g⁻¹) and analyzing the CV curves. The results show that carbon coating in a content of 1.5 wt.% derived from the carbon source of ethylene glycol greatly decreases the particle size of LiFePO₄ in one order in the specific surface area, and significantly improves the rate capability of LiFePO₄. The effect of the content of FeP on the capacity of the carbon coated LiFePO₄ was different at different discharge rates. Increasing the content of FeP from 1.2 to 3.7 wt.% slightly decreases the capacity of LiFePO₄/C at low discharge rate (0.1C and 1C), but obviously increases the capacity of LiFePO₄/C when the discharge rate is increased to 5C. For the carbon free sample, even it also has 1.8 wt.% FeP, it still possesses poor capacity due to the large particle size of LiFePO₄ and the lack of conductivity. And too much iron phosphides lowers the discharge capacity of the electrode since they are inert for the deinsertion/insertion of lithium ion.     

Structural and electrochemical properties of Cl-doped LiFePO4/C

Cl-doped LiFePO₄/C cathode materials were synthesized through a carbothermal reduction route, and the microstructure and electrochemical performances were systematically studied. Cl-doped LiFePO₄/C cathode materials presented a high discharge capacity of ∼90 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. Electrochemical impedance spectroscopy and cyclic voltamperometry indicated the optimized electrochemical reaction and Li⁺ diffusion in the bulk of LiFePO₄ due to Cl-doping. The improved Li⁺ diffusion capability is attributed to the microstructure modification of LiFePO₄ via Cl-doping.