Organic-inorganic crosslinked and hybrid membranes derived from sulfonated poly(arylene ether sulfone)/silica via sol-gel process

A series of covalently crosslinkable organic-inorganic hybrid membranes have been prepared from sulfonated poly(arylene ether sulfone) (SPAES) with pendant propenyl moiety and various amounts of vinyl substituted silica via sol-gel process which are then thermally crosslinked in the presence of benzoyl peroxide (BPO) initiator. The obtained membranes are characterized in terms of oxidative stability, thermal property, ion exchange capacity (IEC), water uptake, swelling ratio in methanol aqueous solution, proton conductivity, and methanol permeability coefficient. The results indicate that the oxidative stability and thermal stability of the hybrid membranes are improved. Moreover, introduction of silica reduces the water uptake and methanol swelling of membranes. The swelling ratio of membranes in 2 mol L⁻¹ methanol aqueous solution at 80 °C slowly decreases from 26 to 19% with the increase of SiO₂ content from 0 to 12 wt.%. Furthermore, with the increase in silica content, the methanol permeability coefficient of the hybrid membranes decreases at first and then increases. When the silica content reaches 8 wt.%, the methanol permeability coefficient is at the minimum of 6.02 × 10⁻⁷ cm² s⁻¹, a 2.64-fold decrease compared with that of the pristine SPAES membrane. Moreover, the proton conductivity is found to be at about 95% of that of pristine polymer at that silica content.     

Alkyl chain modified sulfonated poly(ether sulfone) for fuel cell applications

A new alkyl chain modified sulfonated poly(ether sulfone) (mPES) was synthesized and formed into membranes. The MEAs were tested in the PEMFC and evaluated systematically in the DMFC by varying the methanol concentration from 0.5 to 5.0 M at 60 °C and 70 °C. The synthesized mPES copolymer has been characterized by nuclear magnetic resonance spectroscopy, fourier transform infrared spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The proton conductivity of the resulting membrane is higher than the threshold value of 10⁻² S cm⁻¹ at room temperature for practical PEM fuel cells. The membrane is insoluble in boiling water, thermally stable until 250 °C and shows low methanol permeability. In the H₂/air PEMFC at 70 °C, a current density of 600 mA cm⁻² leads to a potential of 637 mV and 658 mV for 50 μm thick mPES 60 and Nafion NRE 212, respectively. In the DMFC, mPES 60's methanol crossover current density is 4 times lower than that for Nafion NRE 212, leading to higher OCV values and peak power densities. Among all investigated conditions and materials, the highest peak power density of 120 mW cm⁻² was obtained with an mPES 60 based MEA at 70 °C and a methanol feed of 2 M.     

Crosslinked sulfonated poly(arylene ether sulfone) membranes for fuel cell application

A series of sulfonated poly(arylene ether sulfone) with photocrosslinkable moieties is successfully synthesized by direct copolymerization of 3,3′-disulfonated 4,4′-difluorodiphenyl sulfone (SDFDPS) and 4,4′-difluorodiphenyl sulfone (DFDPS) with 4,4′-biphenol (BP) and 1,3-bis-(4-hydroxyphenyl) propenone (BHPP). The content of crosslinkable moieties in the polymer repeat unit is controlled from 0 to 10 mol% by changing the monomer feed ratio of BHPP to BP. The polymer membranes can be crosslinked by irradiating UV with a wavelength of 365 nm. From FT-IR analysis, it can be identified that UV crosslinking mainly occurs due to the combination reaction of radicals that occurs in conjunction with the breaking of the carbon–carbon double bonds (–CH = CH-) of the chalcone moieties in the backbone. Consequently, a new bond is created to form cyclobutane. The crosslinked membranes show less water uptake, a lower level of methanol permeability, and good thermal and mechanical properties compared to pristine (non-crosslinked) membranes while maintaining a reasonable level of proton conductivity. Finally, the fuel cell performance of the crosslinked membranes is comparable to that of the Nafion 115 membrane, demonstrating that these membranes are promising candidates for use as polymer electrolyte membranes in DMFCs.     

Sulfonated poly(arylene ether sulfone) membranes blended with hydrophobic polymers for direct methanol fuel cell applications

In this paper, proton exchange membranes for direct methanol fuel cells were prepared by blending sulfonated poly(arylene ether sulfone) with poly (vinylidene fluoride-co-hecafluoropropylene)(PVdF-HFP) and polyethersulfone (PES) to decrease methanol permeability while maintaining high proton conductivity. The content of the second polymer, such as PES and PVdF, in the blend membranes was controlled at 10–40 wt% based on SPAES. In order to investigate the effects of the second polymer content in the blended membranes, parameters of the prepared membranes related to fuel cell performance were characterized, including their morphology, mechanical properties, methanol permeability, and proton conductivity. Surface roughness of the blend membrane was increased by the introduction of a hydrophobic polymer. Mechanical properties of the PES/SPAES blend membrane were improved owing to interaction between the sulfonic acid groups in SPAES and PES. However, the tensile strength of the PVdF/SPAES blend membrane was decreased by due to the poor compatibility of SPAES and PVdF. The methanol permeability in the blended membranes decreased with increasing content of PES and PVdF. The SPAES/PES blend membranes exhibited good proton conductivity and lower methanol permeability than the SPAES membrane. The SVdF15 blend membrane showed the highest selectivity due to the absence of methanol crossover and a small decrease of proton conductivity. These blend membranes are suitable for DMFC applications.     

Improvement of electrochemical performances of sulfonated poly(arylene ether sulfone) via incorporation of sulfonated poly(arylene ether benzimidazole)

In the present study, modified acid–base blend membranes were fabricated via incorporation of sulfonated poly(arylene ether benzimidazole) (SPAEBI) into sulfonated poly(arylene ether sulfone) (SPAES). These membranes had excellent methanol-barrier properties in addition to an ability to compensate for the loss of proton conductivity that typically occurs in general acid–base blend system. To fabricate the membranes, SPAEBIs, which served as amphiphilic polymers with different degrees of sulfonation (0–50 mol%), were synthesized by polycondensation and added to SPAES. It resulted in the formation of acid–amphiphilic complexes such as [PAES-SO₃]⁻⁺[H-SPAEBI] through the ionic crosslinking, which prevented SO₃H groups in the complex from transporting free protons in an aqueous medium, contributing to a reduction of ion exchange capacity values and water uptake in the blend membranes, and leading to lower methanol permeability in a water–methanol mixture. Unfortunately, the ionic bonding formation was accompanied by a decrease of bound water content and proton conductivity, although the latter problem was solved to some extent by the incorporation of additional SO₃H groups in SPAEBI. In the SPAES–SPAEBI blend membranes, enhancement of proton conductivity and methanol-barrier property was prominent at temperatures over 90 °C. The direct methanol fuel cell (DMFC) performance, which was based on SPAES–SPAEBI-50–5, was 1.2 times higher than that of Nafion^® 117 under the same operating condition.     

Composite membranes based on a sulfonated poly(arylene ether sulfone) and proton-conducting hybrid silica particles for high temperature PEMFCs

The organic-inorganic composite membranes are prepared by inserting poly(styrene sulfonate)-grafted silica particles into a polymer matrix of sulfonated poly(arylene ether sulfone) copolymer. The first step consisted in using atom transfer radical polymerization method to prepare surface-modified silica particles grafted with sodium 4-styrenesulfonate, referred to as PSS-g-SiO₂. Ion exchange capacities up to 2.4 meq/g are obtained for these modified silica particles. In a second step, a sulfonated poly(arylene ether sulfone) copolymer is synthesized via nucleophilic step polymerization of sulfonated 4,4′-dichlorodiphenyl sulfone, 4,4′-dichlorodiphenyl sulfone and phenolphthalin monomers in the presence of potassium carbonate. The copolymer is blended with various amounts of silica particles to form organic-inorganic composite membranes. Esterification reaction is carried out between silica particles and the sulfonated polymer chains by thermal treatment in the presence of sodium hypophosphite, which catalyzed the esterification reaction. The water uptake, proton conductivity, and thermal decomposition temperature of the membranes are measured. All composite membranes show better water uptake and proton conductivity than the unmodified membrane. Moreover, the membranes are tested in a commercial single cell at 80 °C and 120 °C in humidified H₂/air under different relative humidity conditions. The composite membrane containing 10%(w/w) of PSS-g-SiO₂ particles, which have ester bonds between polymer chains and silica particles, showed the best performance of 690 mA cm⁻² at 0.6 V, 120 °C and 30 %RH, even higher than the commercial Nafion^® 112 membrane.     

Synthesis and characterization of crosslinked sulfonated poly(arylene ether sulfone) membranes for high temperature PEMFC applications

Sulfonated poly(arylene ether sulfone) copolymers containing carboxyl groups are prepared by an aromatic substitution polymerization reaction using phenolphthalin, 3,3′-disulfonated-4,4′-dichlorodiphenyl sulfone, 4,4′-dichlorodiphenyl sulfone and 4,4′-bisphenol A as polymer electrolyte membranes for the development of high temperature polymer electrolyte membrane fuel cells. Thin, ductile films are fabricated by the solution casting method, which resulted in membranes with a thickness of approximately 50 μm. Hydroquinone is used to crosslink the prepared copolymer in the presence of the catalyst, sodium hypophosphite. The synthesized copolymers and membranes are characterized by ¹H NMR, FT-IR, TGA, ion exchange capacity, water uptake and proton conductivity measurements. The water uptake and proton conductivity of the membranes are decreased with increasing the degree of crosslinking which is determined by phenolphthalin content in the copolymer (0-15 mol%). The prepared membranes are tested in a 9 cm² commercial single cell at 80 °C and 120 °C in humidified H₂/air under different relative humidity conditions. The uncrosslinked membrane is found to perform better than the crosslinked membranes at 80 °C; however, the crosslinked membranes perform better at 120 °C. The crosslinked membrane containing 10 mol% of phenolphthalin (CPS-PP10) shows the best performance of 600 mA cm⁻² at 0.6 V and better performance than the commercial Nafion^® 112 (540 mA cm⁻² at 0.6 V) at 120 °C and 30 % RH.     

Quinoxaline-based crosslinked membranes of sulfonated poly(arylene ether sulfone)s for fuel cell applications

A series of crosslinkable sulfonated poly(arylene ether sulfone)s (SPAESs) were synthesized by copolymerization of 4,4′-biphenol with 2,6-difluorobenzil and 3,3′-disulfonated-4,4′-difluorodiphenyl sulfone disodium salt. Quinoxaline-based crosslinked SPAESs were prepared via the cyclocondensation reaction of benzil moieties in polymer chain with 3,3′-diaminobenzidine to form quinoxaline groups acting as covalent and acid-base ionic crosslinking. The uncrosslinked and crosslinked SPAES membranes showed high mechanical properties and the isotropic membrane swelling, while the later became insoluble in tested polar aprotic solvents. The crosslinking significantly improved the membrane performance, i.e., the crosslinked membranes had the lower membrane dimensional change, lower methanol permeability and higher oxidative stability than the corresponding precursor membranes, with keeping the reasonably high proton conductivity. The crosslinked membrane (CS1-2) with measured ion exchange capacity of 1.53 mequiv. g⁻¹ showed a reasonably high proton conductivity of 107 mS/cm with water uptake of 48 wt.% at 80 °C, and exhibited a low methanol permeability of 2.3 × 10⁻⁷ cm² s⁻¹ for 32 wt.% methanol solution at 25 °C. The crosslinked SPAES membranes have potential for PEFC and DMFCs.     

Synthesis and properties of sulfonated poly(arylene ether phosphine oxide)s for proton exchange membranes

A series of sulfonated poly(arylene ether phosphine oxide)s (sPAEPO) were prepared by direct polycondensation of sulfonated bis(4-fluorophenyl)phenyl phosphine oxide and bis(4-fluorophenyl)phenyl phosphine oxide with various diphenol-type monomers. The resulting ionomers show high molecular weight and excellent thermal stability. The bisphenol moieties of sPAEPO greatly affect the properties. sPAEPO-NA, -Bis A, -BP, and -6F show excellent dimensional stability. However, sPAEPO-DB and -HQ indicate abrupt swelling even at 80 and 90 °C, respectively, unsuitable for proton exchange membranes. In contrast, sPAEPO-6F with the lowest swelling exhibits the highest conductivity of 7.68 × 10⁻² S cm⁻¹ among all the sPAEPO, close to that of Nafion 117. Besides, sPAEPO-NA and -Bis A show a worse oxidative stability than other sPAEPO (sPAEPO-Bis A, -BP, -HQ, and -6F) due to the naphthalene ring and the isopropylidene unit in the backbone, respectively. Contrary to sPAEPO-Bis A and -BP, sPAEPO-NA and -6F exhibit well connective ionic domains owing to the high hydrophobic nature of the naphthalene ring and hexafluoroisopropylidene moieties. The connected ionic domains provide sPAEPO-NA and -6F with higher proton conductivity in comparison with sPAEPO-Bis A and -BP. In conclusion, sPAEPO-6F has the best comprehensive properties among all the sPAEPO, indicating a promising prospect in proton exchange membrane applications.     

Synthesis and characterization of sulfonated poly(arylene ether ketone ketone sulfone) membranes for application in proton exchange membrane fuel cells

A series of sulfonated poly(arylene ether ketone ketone sulfone) (SPAEKKS) copolymers were synthesized by nucleophilic polycondensation. The copolymers exhibit good thermal and oxidative stabilities, all the SPAEKKS copolymers can be cast into tough membranes. Ionic exchange capacities (IEC), water uptake properties, thermal stabilities, methanol diffusion coefficients and proton conductivities were thoroughly studied. Also the microstructures of the membranes were investigated by TEM. The proton conductivity of the SPAEKKS-4 membrane is close to that of Nafion-117 at 80 °C. The methanol diffusion coefficient of the membrane is much lower than that of Nafion-117 under the same testing conditions. The SPAEKKS membranes are promising in proton exchange membranes fuel cell (PEMFC) application.     

Cross-linked miscible blend membranes of sulfonated poly(arylene ether sulfone) and sulfonated polyimide for polymer electrolyte fuel cell applications

Cross-linked miscible blend (CMB) membranes were prepared from sulfonated poly(arylene ether sulfone) (SPAES) and sulfonated polynaphthalimide (SPI). They were transparent and insoluble in solvents. They showed the intermediate properties between SPAES and SPI concerning mechanical strength, water uptake, membrane swelling and proton conductivity. As for membrane swelling and proton conductivity, SPAES was almost isotropic, whereas SPI was highly anisotropic. CMB membranes were moderately anisotropic and had the advantages of the smaller in-plane membrane swelling and the larger through-plane conductivity compared to SPAES and SPI, respectively. Polymer electrolyte fuel cell performance of CMB2 membrane with an equal weight ratio of SPAES/SPI and an ion exchange capacity (IEC) of 1.74 meq g⁻¹ was investigated, compared to SPI membrane (R1) with a slightly higher IEC of 1.86 meq g⁻¹. At 90 °C, 0.1 MPa and relatively high humidification of 82/68% RH or 0.2 MPa and low humidification of 50-30% RH, CMB2 showed the reasonably high cell performances. At 110 °C and 50-33% RH, the cell performance was fairly high only at a high pressure of 0.3 MPa, but low at 0.2-0.15 MPa. At these conditions, the cell performance was better for CMB2 than for R1 due to the more effective back-diffusion of water formed at cathode into membrane. CMB2 showed the fairly high PEFC durability at 110 °C.     

Sulfonated poly(arylene ether sulfone) as a methanol-barrier layer in multilayer membranes for direct methanol fuel cells

Novel poly(arylene ether sulfone) copolymers containing different amount of pendant sulfonic acid groups have been synthesized by an aromatic substitution polymerization reaction. The properties of the synthesized sulfonated poly(diphenylsulfone-diphenol) (SDPS-DP) copolymers depend on the sulfonic acid group content in the copolymers. Although all the copolymers show good thermal stability, low liquid uptake, and low methanol crossover, they exhibit lower proton conductivity than Nafion or sulfonated poly(ether ether ketone) (SPEEK). Taking advantage of the low methanol crossover, multilayer membranes consisting of the SDPS-DP copolymer as a methanol-barrier center layer and SPEEK as the proton-conducting outer layers have been fabricated and characterized. The SPEEK/SDPS-DP-60/SPEEK multilayer membranes with an optimized center layer thickness are found to exhibit better performance and higher power density in DMFC than plain SPEEK and Nafion 115 membranes.     

Novel cross-linked sulfonated poly (arylene ether ketone) membranes for direct methanol fuel cell

To prepare a cross-linked proton exchange membrane with low methanol permeability and high proton conductivity, poly (vinyl alcohol) is first blended with sulfonated poly (arylene ether ketone) bearing carboxylic acid groups (SPAEK-C) and then heated to induce a cross-linking reaction between the carboxyl groups in SPAEK-C and the hydroxyl groups in PVA. Fourier transform infrared spectroscopy is used to characterize and confirm the structure of SPAEK-C and the cross-linked membranes. The proton conductivity of the cross-linked membrane with 15% PVA in weight reaches up to 0.18 S cm⁻¹ at 80 °C (100% relative humidity), which is higher than that of Nafion membrane, while the methanol permeability is nearly five times lower than Nafion. The ion-exchange capacity, water uptake and thermal stability are investigated to confirm their applicability in fuel cells.     

Preparation and properties of crosslinked sulphonated poly(arylene ether sulphone) blend s for direct methanol fuel cell applications

HMS-based sulphonated poly(arylene ether sulphone) (HMSSH) is synthesised using 4,4′-dihydroxy-α-methylstilbene (HMS) monomer to introduce an interesting stilbene core as crosslinkable group. Crosslinked blend membranes are obtained by blending the BPA-based sulphonated poly(arylene ether sulphone) (BPASH) with crosslinkable HMS-based sulphonated poly(arylene ether sulphone) by UV irradiation of the blend membrane. Compared to the native BPASH with crosslinked BPASH/HMSSH blend membranes, the crosslinked blend membranes greatly reduce the water uptake and methanol permeability with only a slight reduction in proton conductivity. The crosslinked blend membrane, which has a 6% HMSSH content, has a water uptake of 59%, methanol permeability of 0.75 × 10⁻⁶ cm² s⁻¹, and proton conductivity of 0.08 S cm⁻¹. A membrane-electrode assembly is used to investigate single-cell performance and durability test for DMFC applications. Both the power density and open circuit voltage are higher than those of Nafion^® 117. A maximum power density of 32 mW cm⁻² at 0.2 V is obtained at 80 °C, which is higher than that of Nafion^® 117 (25 mW cm⁻²).     

4-Aminopyridine grafted sulfonated poly(arylene ether ketone sulfone) proton exchange membrane with high relative selectivity for fuel cells

A series of sulfonated poly(arylene ether ketone sulfone)s polymer having a degree of sulfonation of 80% and a carboxyl group in the side chain (C-SPAEKS) were prepared by polycondensation. The 4-aminopyridine grafted sulfonated poly(arylene ether ketone sulfone)s polymer membranes (SPPs) were prepared by amidation reaction with the carboxyl group to immobilize 4-aminopyridine on the side chain. The ¹H NMR results and Fourier transform infrared of SPP membranes demonstrated the successful grafting of the 4-aminopyridine. Proton conductivity, water absorption, swelling ratio, and thermal stability of different proportions of SPP membranes were investigated under the different conditions. With the increase of pyridine grafting content, the methanol permeability coefficient of the membrane decreased significantly from 8.17 × 10⁻⁷ cm²s⁻¹ to 8.92 × 10⁻⁸ cm²s⁻¹ at 25 °C. And, the proton conductivity and relative selectivity of the membrane were positively correlated with the grafted pyridine content. Among them, the SPP-4 membrane exhibited the highest proton conductivity of 0.088 Scm⁻¹ at 100 °C. The relative selectivity increased from 4.73 × 10⁴ S scm⁻³ to 9.84 × 10⁴ S scm⁻³.     

Preparation of main-chain-type and side-chain-type sulfonated poly(ether ether ketone) membranes for direct methanol fuel cell applications

Novel main-chain-type and side-chain-type sulphonated poly(ether ether ketone)s (MS-SPEEKs) are synthesised by reacting the sulphonic acid groups of pristine SPEEKs with 2-aminoethanesulphonic acid to improve the nano-phase separated morphology of the material. ¹H NMR and FT-IR spectroscopy are employed to determine the structure and composition of main-chain-type and side-chain-type sulphonated polymers. Flexible and tough membranes with reasonable thermal properties are obtained. The MS-SPEEKs show good hydrolytic stability, and water uptake values ranging from 15% to 30% are observed. Compared to Nafion 117^®, the methanol permeability of the MS-SPEEKs is dramatically reduced to 8.83 × 10⁻⁸ cm² s⁻¹ to 3.31 × 10⁻⁷ cm² s⁻¹. The proton conductivity increases with increasing temperature, reaching 0.013-0.182 S cm⁻¹. A maximum power density and open circuit voltage of 115 mW cm⁻² and 0.830 V are obtained at 80 °C, respectively, which is significantly greater than the values generated with Nafion 117^®. The introduction of pendent side-chain-type sulphonic acid groups increases the single-cell performance by more than approximately 20%; thus, the lower water diffusivity, methanol permeability, electro-osmotic drag coefficient and high cell performance indicated that MS-SPEEK is a promising candidate for DMFC applications.     

Synthesis and properties of sulfonated poly(arylene ether ketone sulfone) containing amino groups/functional titania inorganic particles hybrid membranes for fuel cells

In this work, the organic-inorganic hybrid membranes were prepared. The synthesis and properties of the hybrid membranes were investigated. The sulfonated poly(arylene ether ketone sulfone) containing amino groups (Am-SPAEKS) was synthesized by nucleophilic polycondensation. The sol-gel method was used to prepared functional titania inorganic particles (L-TiO₂). The ¹H NMR and FT-IR were performed to verified the structure of Am-SPAEKS and L-TiO₂. The organic-inorganic hybrid membranes showed both good thermal stabilities and mechanical properties than that of Am-SPAEKS. The L-Am-15% membrane exhibited the highest Young's modulus (2262.71 MPa) and Yield stress (62.09 MPa). The distribution of L-TiO₂ particles was revealed by SEM. Compared to Am-SPAEKS, the hybrid membranes showed higher proton conductivities. The L-Am-15% exhibited the highest proton conductivity of 0.0879 S cm⁻¹ at 90 °C. The results indicate that the organic-inorganic hybrid membranes have potential for application in proton exchange membrane fuel cells.     

Crosslinked sulfonated poly(ether ether ketone) proton exchange membranes for direct methanol fuel cell applications

In the present study, a series of the crosslinked sulfonated poly(ether ether ketone) (SPEEK) proton exchange membranes were prepared. The photochemical crosslinking of the SPEEK membranes was carried out by dissolving benzophenone and triethylamine photo-initiator system in the membrane casting solution and then exposing the resulting membranes after solvent evaporation to UV light. The physical and transport properties of crosslinked membranes were investigated. The membrane performance can be controlled by adjusting the photoirradiation time. The experimental results showed that the crosslinked SPEEK membranes with photoirradiation 10 min had the optimum performance for proton exchange membranes (PEMs). Compared with the non-crosslinked SPEEK membranes, the crosslinked SPEEK membranes with photoirradiation 10 min markedly improved thermal stabilities and mechanical properties as well as hydrolytic and oxidative stabilities, greatly reduced water uptake and methanol diffusion coefficients with only slight sacrifice in proton conductivities. Therefore, the crosslinked SPEEK membranes with photoirradiation 10 min were particularly promising as proton exchange membranes for direct methanol fuel cell (DMFC) applications.     

Sulfonated poly(arylene ether sulfone)s membranes with distinct microphase-separated morphology for PEMFCs

Copoly (arylene ether sulfone)s was employed for proton exchange membrane preparation via atom transfer radical polymerization followed by mild sulfonation, enhanced phase-separated morphology and favorable proton conductivity were achieved. The comprehensive ex-situ properties of a range of membranes with different ion exchange capacities were characterized alongside the fuel cell performances investigation. The membranes exhibit higher water uptake, which is beneficial to the proton conduction, compared to Nafion® 211 while maintaining similar swelling ratio. The prepared membranes exhibit reasonably high proton conductivity (0.16 S/cm at 85 °C) benefitting from the well-defined microstructure and high connectivity of the hydrophilic domains. Considering the comprehensive property, membrane with moderate ion exchange capacity (1.39 mmol/g) was employed to fabricate the membrane electrode assembly and peak power density of 0.65 W/cm² at 80 °C, 60% relative humidity was achieved for a H₂/O₂ fuel cell, these hydrocarbon membranes can therefore be implemented in PEMFCs.     

Fluorene-containing poly(arylene ether sulfone)s with imidazolium on flexible side chains for anion exchange membranes

Anion exchange membranes with high ionic conductivity and dimensional stability attract a lot of research interests. In present study, a series of fluorene-containing poly(arylene ether sulfone)s containing imidazolium on the flexible long side-chain are synthesized via copolycondensation, Friedel-Crafts reaction, ketone reduction, and Menshutkin reaction sequentially. The membranes used for characterization and membrane electrode assembly are obtained by solution casting and ion exchange thereafter. The morphology of the membranes is studied via transmission electron microscopy, and the microphase separation is observed. The long side-chain structure is responsible for the distinct hydrophilic-hydrophobic microphase separation, which facilitates the transport of hydroxide ions in the membranes. The incorporation of imidazolium on the flexible long side-chain is favorable for the ionic aggregation and transport in the membranes. The resulted membranes exhibit high hydroxide conductivities in the range of 48.5–83.1 mS cm⁻¹ at 80 °C. All these membranes show good dimensional stability and thermal stability. The single cell performance shows a power density of 102.3 mW cm⁻² at 60 °C using membrane electrode assembly based-on one of the synthesized polymers.