Enhanced performance of a single-chamber solid oxide fuel cell with an SDC-impregnated cathode

The electrochemical performance of anode-supported single-chamber solid oxide fuel cells (SC-SOFCs) with and without SDC-impregnated cathodes was compared in a diluted methane–oxygen mixture. These cells were made of conventional materials including yttrium-stabilized zirconia (YSZ) thin film, a Ni + YSZ anode and a La_0.7Sr_0.3MnO₃ (LSM) cathode. Our results showed that the cell performance was greatly enhanced with the SDC-impregnated LSM cathode. At a furnace temperature of 750 °C, the maximum power density was as high as 404 mW cm⁻² for a CH₄ to O₂ ratio of 2:1, which was 4.0 times higher than the cell with a pure LSM cathode (100 mW cm⁻²). The overall polarization resistance of the impregnated cell was 1.6 Ω cm², which was much smaller than that of the non-impregnated one (4.2 Ω cm²). The impregnation introduced SDC nanoparticles greatly extended the electrochemical active zone and hence greatly improved the cell performance.     

Performance and durability of nanostructured (La0.85Sr0.15)0.98MnO3/yttria-stabilized zirconia cathodes for intermediate-temperature solid oxide fuel cells

In this communication we report the fabrication of nanostructured (La_0.85Sr_0.15)_0.98MnO₃ (LSM)/yttria-stabilized zirconia (YSZ) composite cathodes consisting of homogeneously distributed and connected LSM and YSZ grains approximately 100 nm large. We also investigate for the first time the role of the cathode nanostructure on the performance and the durability of intermediate-temperature solid oxide fuel cells. The cathodes were fabricated using homogenous LSM/YSZ nanocomposite particles synthesized by co-precipitation, using YSZ nanoparticles of 3 nm as seed crystals. Detailed microstructural characterization by transmission electron microscopy with energy-dispersive X-ray spectroscopy revealed that many of the LSM/YSZ junctions in the cathode faced the homogeneously connected pore channels, indicating the formation of a considerable number of triple phase boundaries. The nanostructure served to reduce cathodic polarization. As a result, these anode-supported solid oxide fuel cells showed high power densities of 0.18, 0.40, 0.70 and 0.86 W cm⁻² at 650, 700, 750 and 800 °C, respectively, under the cell voltage of 0.7 V. Furthermore, no significant performance degradation of the cathode was observed during operation at 700 °C for 1000 h under a constant current density of 0.2 A cm⁻².     

Effect of SDC-impregnated LSM cathodes on the performance of anode-supported YSZ films for SOFCs

Sm_0.2Ce_0.8O_1.9 (SDC)-impregnated La_0.7Sr_0.3MnO₃ (LSM) composite cathodes were fabricated on anode-supported yttria-stabilized zirconia (YSZ) thin films. Electrochemical performances of the solid oxide fuel cells (SOFCs) were investigated in the present study. Four single cells, i.e., Cell-1, Cell-2, Cell-3 and Cell-4 were obtained after the fabrication of four different cathodes, i.e., pure LSM and SDC/LSM composites in the weight ratios of 25/75, 36/64 and 42/58, respectively. Impedance spectra under open-circuit conditions showed that the cathode performance was gradually improved with the increasing SDC loading. Similarly, the maximum power densities (MPD) of the four cells were increased with the SDC amount below 700 °C. Whereas, the cell performance of Cell-4 was lower than that of Cell-3 at 800 °C, arising from the increased concentration polarization at high current densities. This was caused by the lowered porosity with the impregnation cycle. This disadvantage could be suppressed by lowering the operating temperature or by increasing the oxygen concentration at the cathode side. The ratio of electrode polarization loss in the total voltage drop versus current density showed that the cell performance was primarily determined by the electrode polarization. The contribution of the ohmic resistance was increased when the operating temperature was lowered. When a 100 ml min⁻¹ oxygen flow was introduced to the cathode side, Cell-3 produced MPDs of 1905, 1587 and 1179 mW cm⁻² at 800, 750 and 700 °C, respectively. The high cell outputs demonstrated the merits of the novel and effective SDC-impregnated LSM cathodes.     

Thin film solid oxide fuel cells with copper cermet anodes

Thin film solid oxide fuel cells (SOFCs), composed of thin coatings of 8 mol% Y₂O₃-stabilized ZrO₂ (YSZ) and thick substrates of (La_0.8Sr_0.2)_0.98MnO₃ (LSM)-YSZ cathodes, are fabricated using the conventional tape casting and tape lamination techniques. Densification of YSZ electrolyte thin films is achieved at 1275 °C by adjusting the cathode tape formulation and sintering characteristics. Two types of copper cermets, CuO-YSZ-ceria and CuO-SDC (Ce_0.85Sm_0.15O_1.925)-ceria, are compared in terms of the anodic performance in hydrogen and propane. Maximum power densities for hydrogen and propane at 800 °C are 0.26 W cm⁻² and 0.17 W cm⁻² for CuO-YSZ-ceria anodes and 0.35 W cm⁻² and 0.22 W cm⁻² for CuO-SDC-ceria anodes, respectively. Electrochemical impedance analysis suggests that CuO-SDC-ceria exhibits a much lower anodic polarization resistance than CuO-YSZ-ceria, which could be explained by the intrinsic mixed oxygen ionic and electronic conductivities for SDC in the reducing atmosphere.     

Low-temperature solid oxide fuel cells with La1−xSrxMnO3 as the cathodes

La_1−xSr_xMnO₃ (LSM) has been widely developed as the cathode material for high-temperature solid oxide fuel cells (SOFCs) due to its chemical and mechanical compatibilities with the electrolyte materials. However, its application to low-temperature SOFCs is limited since its electrochemical activity decreases substantially when the temperature is reduced. In this work, low-temperature SOFCs based on LSM cathodes are developed by coating nanoscale samaria-doped ceria (SDC) onto the porous electrodes to significantly increase the electrode activity of both cathodes and anodes. A peak power density of 0.46 W cm⁻² and area specific interfacial polarization resistance of 0.36 Ω cm² are achieved at 600 °C for single cells consisting of Ni-SDC anodes, LSM cathodes, and SDC electrolytes. The cell performances are comparable with those obtained with cobalt-based cathodes such as Sm_0.5Sr_0.5CoO₃, and therefore encouraging in the development of low-temperature SOFCs with high reliability and durability.     

NiO/YSZ,anode-supported,thin-electrolyte,solid oxide fuel cells fabricated by gel casting

A simple and cost-effective gel-casting technique is developed and optimized to fabricate NiO/stabilized yttria–zirconia (YSZ) anode-supported solid oxide fuel cells (SOFCs). The effect of ammonium poly-(methacrylate) (PMAA) dispersant and pH on the zeta potential of YSZ and NiO particles and the viscosity of the NiO/YSZ slurries is studied in detail. The results show that the absolute zeta potential of YSZ and NiO particles reaches a maximum value at pH value ∼10 and the viscosity of the NiO/YSZ slurry is lowest when the PMAA dispersant content is 1.5 wt.%. A gel-cast NiO/YSZ anode-supported button cell with a spin-coated, thin, YSZ electrolyte film (∼9 μm) and a La_0.72Sr_0.18MnO_3−δ (LSM)/YSZ composite cathode gives a peak power output of 1.07 and 0.65 W cm⁻² at 900 and 800 °C under humidified hydrogen and air. The effect of a graphite pore-former in the gelation and microstructure of NiO/YSZ anode substrates is investigated.     

Fabrication and characterization of Sm0.2Ce0.8O2−δ-Sm0.5Sr0.5CoO3−δ composite cathode for anode supported solid oxide fuel cell

The Sm_0.5Sr_0.5CoO_3−δ (SSC) with perovskite structure is synthesized by the glycine nitrate process (GNP). The phase evolution of SSC powder with different calcination temperatures is investigated by X-ray diffraction and thermogravimetric analyses. The XRD results show that the single perovskite phase of the SSC is completely formed above 1100 °C. The anode-supported single cell is constructed with a porous Ni-yttria-stabilized zirconia (YSZ) anode substrate, an airtight YSZ electrolyte, a Sm_0.2Ce_0.8O_2−δ (SDC) barrier layer, and a screen-printed SSC-SDC composite cathode. The SEM results show that the dense YSZ electrolyte layer exhibits the good interfacial contact with both the Ni-YSZ and the SDC barrier layer. The porous SSC-SDC cathode shows an excellent adhesion with the SDC barrier layer. For the performance test, the maximum power densities are 464, 351 and 243 mW cm⁻² at 800, 750 and 700 °C, respectively. According to the results of the electrochemical impedance spectroscopy (EIS), the charge-transfer resistances of the electrodes are 0.49 and 1.24 Ω cm², and the non charge-transfer resistances are 0.48 and 0.51 Ω cm² at 800 and 700 °C, respectively. The cathode material of SSC is compatible with the YSZ electrolyte via a delicate scheme employed in the fabrication process of unit cell.     

Electrochemical characteristics of samaria-doped ceria infiltrated strontium-doped LaMnO3 cathodes with varied thickness for yttria-stabilized zirconia electrolytes

Samaria-doped ceria (SDC) infiltrated into strontium-doped LaMnO₃ (LSM) cathodes with varied cathode thickness on yttria-stabilized zirconia (YSZ) were investigated via symmetrical cell, half cell, and full cell configurations. The results of the symmetrical cells showed that the interfacial polarization resistance (R_P) decreased with increasing electrode thickness up to ∼30 μm, and further increases in the thickness of the cathode did not cause significant variation of electrode performance. At 800 °C, the minimum R_P was around 0.05 Ω cm². The impedance spectra indicated that three main electrochemical processes existed, possibly corresponding to the oxygen ion incorporation, surface diffusion of oxygen species and oxygen adsorption and dissociation. The DC polarization on the half cells and characterization of the full cells also demonstrated a similar correlation between the electrode performance and the electrode thickness. The peak power densities of the single cells with the 10, 30, and 50-μm thick electrodes were 0.63, 1.16 and 1.11 W cm⁻², respectively. The exchange current densities under moderate polarization are calculated and possible rate-determining steps are discussed.     

GdBaCo2O5+x layered perovskite as an intermediate temperature solid oxide fuel cell cathode

GdBaCo₂O_5+x (GBCO) was evaluated as a cathode for intermediate-temperature solid oxide fuel cells. A porous layer of GBCO was deposited on an anode-supported fuel cell consisting of a 15 μm thick electrolyte of yttria-stabilized zirconia (YSZ) prepared by dense screen-printing and a Ni–YSZ cermet as an anode (Ni–YSZ/YSZ/GBCO). Values of power density of 150 mW cm⁻² at 700 °C and ca. 250 mW cm⁻² at 800 °C are reported for this standard configuration using 5% of H₂ in nitrogen as fuel. An intermediate porous layer of YSZ was introduced between the electrolyte and the cathode improving the performance of the cell. Values for power density of 300 mW cm⁻² at 700 °C and ca. 500 mW cm⁻² at 800 °C in this configuration were achieved.     

Low-temperature ceria-electrolyte solid oxide fuel cells for efficient methanol oxidation

Low temperature anode-supported solid oxide fuel cells with thin films of samarium-doped ceria (SDC) as electrolytes, graded porous Ni-SDC anodes and composite La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF)-SDC cathodes are fabricated and tested with both hydrogen and methanol fuels. Power densities achieved with hydrogen are between 0.56 W cm⁻² at 500 °C and 1.09 W cm⁻² at 600 °C, and with methanol between 0.26 W cm⁻² at 500 °C and 0.82 W cm⁻² at 600 °C. The difference in the cell performance can be attributed to variation in the interfacial polarization resistance due to different fuel oxidation kinetics, e.g., 0.21 Ω cm² for methanol versus 0.10 Ω cm² for hydrogen at 600 °C. Further analysis suggests that the leakage current densities as high as 0.80 A cm⁻² at 600 °C and 0.11 A cm⁻² at 500 °C, resulting from the mixed electronic and ionic conductivity in the SDC electrolyte and thus reducing the fuel efficiency, can nonetheless help remove any carbon deposit and thereby ensure stable and coking-free operation of low temperature SOFCs in methanol fuels.     

High-performance cathode-supported solid oxide fuel cells with copper cermet anodes

Thin film solid oxide fuel cells, composed of thin coatings of 8 mol% Y₂O₃-stabilized ZrO₂ (YSZ), thick substrates of infiltrated La_0.8S_0.2FeO₃ (LSF)-YSZ cathodes and CuO-SDC (Ce_0.85Sm_0.15O_1.925)-ceria anodes, are fabricated using the conventional tape casting and infiltration methods. Infiltrated LSF-YSZ cathodes exhibit a much lower interfacial polarization resistance than (La_0.8Sr_0.2)_0.98MnO₃ (LSM)-YSZ cathodes due to the mixed ionic and electronic conducting behavior of LSF, especially at low operation temperatures. The single cell has shown good and stable performance in hydrogen and hydrocarbon fuels. Maximum power densities for hydrogen, propane, dodecane and low sulfur diesel at 800 °C are 0.62 W cm⁻², 0.40 W cm⁻², 0.37 W cm⁻² and 0.36 W cm⁻², respectively.     

Fabrication of bilayered YSZ/SDC electrolyte film by electrophoretic deposition for reduced-temperature operating anode-supported SOFC

Bilayered Y₂O₃-stabilized ZrO₂ (YSZ)/Sm₂O₃-doped CeO₂ (SDC) electrolyte films were successfully fabricated on porous NiO–YSZ composite substrates by electrophoretic deposition (EPD) based on electrophoretic filtration followed by co-firing with the substrates. In EPD, positively charged YSZ and SDC powders were deposited directly on the substrates, layer by layer from ethanol-based suspensions. Delamination between YSZ and SDC films was avoided by reducing the SDC films’ thickness to ca. 1 μm. A single cell was constructed on the bilayered electrolyte films composed of ca. 4 μm-thick YSZ and ca. 1 μm-thick SDC films. As a cathode in the cell, La_0.6Sr_0.4Co_0.2Fe_0.8O_3−x (LSCF) was used. Maximum output power densities greater than 0.6 W cm⁻² were obtained at 700 °C for the bilayered YSZ/SDC electrolyte cells thus constructed.     

Significant impact of the current collection material and method on the performance of Ba0.5Sr0.5Co0.8Fe0.2O3−δ electrodes in solid oxide fuel cells

The effects of the current collection material and method on the performance of SOFCs with Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCF) cathodes are investigated. Ag paste and LaCoO₃ (LC) oxide are studied as current collection materials, and five different current collecting techniques are attempted. Cell performances are evaluated using a current-voltage test and electrochemical impedance spectra (EIS) based on two types of anode-supported fuel cells, i.e., NiO + SDC|SDC|BSCF and NiO + YSZ|YSZ|SDC|BSCF. The cell with diluted Ag paste as the current collector exhibits the highest peak power density, nearly 16 times that of a similar cell without current collector. The electrochemical characteristics of the BSCF cathode with different current collectors are further determined by EIS at 600 °C using symmetrical cells. The cell with diluted Ag paste as the current collector displays the lowest ohmic resistance (1.4 Ω cm²) and polarization resistance (0.1 Ω cm²). Meanwhile, the surface conductivities of various current collectors are measured by a four-probe DC conductivity technique. The surface conductivity of diluted Ag paste is 2-3 orders of magnitude higher than that of LC or BSCF. The outstanding surface conductivity of silver may reduce the contact resistance at the current collector/electrode interface and, thus, contributes to better electrode performance.     

La0.4Ce0.6O1.8–La0.8Sr0.2MnO3–8 mol% yttria-stabilized zirconia composite cathode for anode-supported solid oxide fuel cells

The composite cathodes of La_0.4Ce_0.6O_1.8 (LDC)–La_0.8Sr_0.2MnO₃ (LSM)–8 mol% yttria-stabilized zirconia (YSZ) with different LDC contents were investigated for anode-supported solid oxide fuel cells with thin film YSZ electrolyte. The oxygen temperature-programmed desorption profiles of the LDC–LSM–YSZ composites indicate that the addition of LDC increases surface oxygen vacancies. The cell performance was improved largely after the addition of LDC, and the best cell performance was achieved on the cells with the composite cathodes containing 10 wt% or 15 wt% LDC. The electrode polarization resistance was reduced significantly after the addition of LDC. At 800 °C and 650 °C, the polarization resistances of the cell with a 10 wt% LDC composite cathode are 70% and 40% of those of the cell with a LSM–YSZ composite cathode, respectively. The impedance spectra show that the processes associated with the dissociative adsorption of oxygen and diffusion of oxygen intermediates and/or oxygen ions on LSM surface and transfer of oxygen species at triple phase boundaries are accelerated after the addition of LDC.     

Improved high temperature performance of La0.8Sr0.2MnO3 cathode by addition of CeO2

Ceria is proposed as an additive for La_0.8Sr_0.2MnO₃ (LSM) cathodes in order to increase both their thermal stability and electrochemical properties after co-sintering with an yttria-stabilized zirconia (YSZ) electrolyte at 1350 °C. Results show that LSM without CeO₂ addition is unstable at 1350 °C, whereas the thermal stability of LSM is drastically improved after addition of CeO₂. In addition, results show a correlation between CeO₂ addition and the maximum power density obtained in 300 μm thick electrolyte-supported single cells in which the anode and modified cathode have been co-sintered at 1350 °C. Single cells with cathodes not containing CeO₂ produce only 7 mW cm⁻² at 800 °C, whereas the power density increases to 117 mW cm⁻² for a CeO₂ addition of 12 mol%. Preliminary results suggest that CeO₂ could increase the power density by at least two mechanisms: (1) incorporation of cerium into the LSM crystal structure, and (2) by modification or reduction of La₂Zr₂O₇ formation at high temperature. This approach permits the highest LSM-YSZ co-sintering temperature so far reported, providing power densities of hundreds of mW cm⁻² without the need for a buffer layer between the LSM cathode and YSZ electrolyte. Therefore, this method simplifies the co-sintering of SOFC cells at high temperature and improves their electrochemical performance.     

Novel nano-network cathodes for solid oxide fuel cells

A novel nano-network of Sm_0.5Sr_0.5CoO_3−δ (SSC) is successfully fabricated as the cathodes for intermediate-temperature solid oxide fuel cells (SOFCs) operated at 500–600 °C. The cathode is composed of SSC nanowires formed from nanobeads of less than 50 nm thus exhibiting high surface area and porosity, forming straight path for oxygen ion and electron transportation, resulting in high three-phase boundaries, and consequently showing remarkably high electrode performance. An anode-supported cell with the nano-network cathode demonstrates a peak power density of 0.44 W cm⁻² at 500 °C and displays exceptional performance with cell operating time. The result suggests a new direction to significantly improve the SOFC performance.     

Effect of unsintered gadolinium-doped ceria buffer layer on performance of metal-supported solid oxide fuel cells using unsintered barium strontium cobalt ferrite cathode

In this study, a Gd_0.1Ce_0.9O_1.95 (GDC) buffer layer and a Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCF) cathode, fabricated without pre-sintering, are investigated (unsintered GDC and unsintered BSCF). The effect of the unsintered GDC buffer layer, including the thickness of the layer, on the performance of solid oxide fuel cells (SOFCs) using an unsintered BSCF cathode is studied. The maximum power density of the metal-supported SOFC using an unsintered BSCF cathode without a buffer layer is 0.81 W cm⁻², which is measured after 2 h of operation (97% H₂ and 3% H₂O at the anode and ambient air at the cathode), and it significantly decreases to 0.63 W cm⁻² after 50 h. At a relatively low temperature of 800 °C, SrZrO₃ and BaZrO₃, arising from interaction between BSCF and yttria-stabilized zirconia (YSZ), are detected after 50 h. Introducing a GDC interlayer between the cathode and electrolyte significantly increases the durability of the cell performance, supporting over 1000 h of cell usage with an unsintered GDC buffer layer. Comparable performance is obtained from the anode-supported cell when using an unsintered BSCF cathode with an unsintered GDC buffer layer (0.75 W cm⁻²) and sintered GDC buffer layer (0.82 W cm⁻²). When a sintered BSCF cathode is used, however, the performance increases to 1.23 W cm⁻². The adhesion between the BSCF cathode and the cell can be enhanced by an unsintered GDC buffer layer, but an increase in the layer thickness (1-6 μm) increases the area specific resistance (ASR) of the cell, and the overly thick buffer layer causes delamination of the BSCF cathode. Finally, the maximum power densities of the metal-supported SOFC using an unsintered BSCF cathode and unsintered GDC buffer layer are 0.78, 0.64, 0.45 and 0.31 W cm⁻² at 850, 800, 750 and 700 °C, respectively.     

Electrochemical characteristics of solid oxide fuel cell cathodes prepared by infiltrating (La,Sr)MnO3 nanoparticles into yttria-stabilized bismuth oxide backbones

The electrochemical characteristics of the solid oxide fuel cell (SOFC) cathodes prepared by infiltration of (La_0.85Sr_0.15)_0.9MnO_3−δ (LSM) nanoparticles into porous Y_0.5Bi_1.5O₃ (YSB) backbones are investigated in terms of overpotential, interfacial polarization resistance, and single cell performance obtained with three-electrode cell, symmetrical cell, and single cell, respectively. X-ray diffraction confirms the formation of perovskite LSM by heating the infiltrated nitrates at 800 °C. The electrical conductivity of the electrode measured using Van der Pauw method is 1.67 S cm⁻¹, which is acceptable at the typical SOFC operating temperatures. The single cell with the LSM infiltrated YSB cathode generates maximum power densities of 0.23, 0.45, 0.78, and 1.13 W cm⁻² at 600, 650, 700, and 750 °C, respectively. The oxygen reduction mechanism on the cathode is studied by analyzing the impedance spectra obtained under various temperatures and oxygen partial pressures. The impedance spectra under various cathodic current densities are also measured to study the effect of cathodic polarization on the performance of the cathode.     

Synthesis and evaluation of (La0.6Sr0.4)(Co0.2Fe0.8)O3 (LSCF)–Y0.08Zr0.92O1.96 (YSZ)–Gd0.1Ce0.9O2−δ (GDC) dual composite SOFC cathodes for high performance and durability

This paper investigates a (La_0.6Sr_0.4)(Co_0.2Fe_0.8)O₃ (LSCF)–Y_0.16Zr_0.92O_1.96 (YSZ)–Gd_0.1Ce_0.9O_2−δ (GDC) dual composite cathode to achieve better cathodic performance compared to an LSM/GDC–YSZ dual composite cathode developed in previous research. To synthesize the structures of the LSCF/GDC–YSZ and LSCF/YSZ–GDC dual composite cathodes, nano-porous composite cathodes containing LSCF, YSZ, and GDC were prepared by a two-step polymerizable complex (PC) method which prevents the formation of YSZ–GDC solid solution. At 800 °C, the electrode polarization resistance of the LSCF/YSZ–GDC dual composite cathode showed to be significantly lower (0.075 Ω cm²) compared to that of a commercial LSCF–GDC cathode (0.195 Ω cm²), a synthesized LSCF/GDC–YSZ dual composite cathode (0.138 Ω cm²), and an LSM/GDC–YSZ dual composite cathode (0.266 Ω cm²) respectively. Moreover, the Ni–YSZ anode-supported single cell containing the LSCF/YSZ–GDC dual composite cathode achieved a maximum power density of 1.24 W/cm² and showed excellent durability without degradation under a load of 1.0 A/cm² over 570 h of operation at 800 °C.     

High-performance PrBaCo2O5+δ-Ce0.8Sm0.2O1.9 composite cathodes for intermediate temperature solid oxide fuel cell

PrBaCo₂O_5+δ-Ce_0.8Sm_0.2O_1.9 (PBCO-SDC) composite material are prepared and characterized as cathode for intermediate temperature solid oxide fuel cells (IT-SOFCs). The powder X-ray diffraction result proves that there are no obvious reaction between the PBCO and SDC after calcination at 1100 °C for 3 h. AC impedance spectra based on SDC electrolyte measured at intermediate temperatures shows that the addition of SDC to PBCO improved remarkably the electrochemical performance of a PBCO cathode, and that a PBCO-30SDC cathode exhibits the best electrochemical performance in the PBCO-xSDC system. The total interfacial resistances R_p is the smallest when the content of SDC is 30 wt%, where the value is 0.035 Ω cm² at 750 °C, 0.072 Ω cm² at 700 °C, and 0.148 Ω cm² at 650 °C, much lower than the corresponding interfacial resistance for pure PBCO. The maximum power density of an anode-supported single cell with PBCO-30SDC cathode, Ni-SDC anode, and dense thin SDC/LSGM (La_0.9Sr_0.1Ga_0.8Mg_0.2O_3−δ)/SDC tri-layer electrolyte are 364, 521 and 741 mW cm⁻² at 700, 750 and 800 °C, respectively.