The enhancement of electrical and optical properties of PEDOT:PSS using one-step dynamic etching for flexible application

The conductivity enhancement of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) by dynamic etching process was investigated to introduce the outstanding and simplest method for soft electronics. Four different samples which were pristine PEDOT:PSS, PEDOT:PSS doped with 5 wt.% DMSO, PEDOT:PSS with dipping process, and PEDOT:PSS with dynamic etching process were prepared to compare the properties such as conductivity, morphology, relative atomic percentage, and topography. All samples were characterized by four point probe, current atomic force microscopy (C-AFM), X-ray photoelectron spectroscopy (XPS), and UV–visible spectroscopy. The conductivity of the sample with dynamic etching process showed the highest value as 1299 S/cm among four samples. We proved that the dynamic etching process is superior to remove PSS phase from PEDOT:PSS film, to flow strong current through entire surface of PEDOT:PSS, and to show the smoothest surface (RMS 2.28 nm). XPS analysis was conducted for accurate chemical and structural surface environments of four samples and the relative atomic percentage of PEDOT in the sample with dynamic etching was the highest as 29.5%. The device performance of the sample with the dynamic etching process was outstanding as 10.31 mA/cm² of J_sc, 0.75 eV of V_oc, 0.46 of FF, and 3.53% of PCE. All properties and the device performance for PEDOT:PSS film by dynamic etching process were the most excellent among the samples.     

Optical properties and conductivity of PEDOT:PSS films treated by polyethylenimine solution for organic solar cells

We report on conductivity and optical property of three different types of poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) films [pristine PH1000 film (PH1000-p), with 5 wt.% ethylene glycol additive (PH1000-EG) and with sulfuric acid post-treatment (PH1000-SA)] before and after polyethylenimine (PEI) treatment. The PEI is found to decrease the conductivity of all the PEDOT:PSS films. The processing solvent of 2-methoxyethanol is found to significantly enhance the conductivity of PH1000-p from 1.1 up to 744 S/cm while the processing solvent of isopropanol or water does not change the conductivity of PH1000-p much. As for the optical properties, the PEI treatment slightly changes the transmittance and reflectance of PH1000-p and PH1000-EG films, while the PEI leads to an substantial increase of the absorptance in the spectral region of 400–1100 nm of the PH1000-SA films. Though the optical property and conductivity of the three different types of PEDOT:PSS films vary with the PEI treatment, the treated PEDOT:PSS films exhibit similar low work function. We demonstrate solar cells with a simple device structure of glass/low-WF PEDOT:PSS/P3HT:ICBA/high-WF PEDOT:PSS cells that exhibit good performance with open-circuit voltage of 0.82 V and fill factor up to 0.62 under 100 mW/cm² white light illumination.     

Improvement of electrical conductivity of PEDOT:PSS films by 2-Methylimidazole post treatment

The electrical conductivity of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films was significantly improved without losing the optical transparency by treating the films with solution of 2-Methylimidazole in ethanol. The maximum electrical conductivity of such a thin film reached 930 S cm⁻¹, more than 1150 order of magnitude higher than that of pure PEDOT:PSS film. The mechanism of conductivity enhancement of treated thin PEDOT:PSS films was explored by atomic force microscopy (AFM) and UV/VIS spectrophotometer. The AFM scans show that the surface of the 2-Methylimidazole treated PEDOT:PSS layer is smoother than that of the pristine PEDOT:PSS thin film. Improvement in the morphology, electrical and optical properties of PEDOT:PSS films makes them highly suitable for numerous applications in optoelectronic devices.     

Stable organic photovoltaic with PEDOT:PSS and MoOX mixture anode interfacial layer without encapsulation

Herein, we report about an efficient and stable organic photovoltaic that uses a poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonate) (PEDOT:PSS) and molybdenum oxide (MoO_X) mixture for the anode interfacial layer, and that can reach 4.43% power conversion efficiency (PCE) under AM1.5 conditions. Utilizing PEDOT:PSS:MoO_X (1:1), the shelf lifetime of poly(3-hexylthiophene) (P3HT), and indene-C₆₀ bisadduct (ICBA)-based solar cells without encapsulation, can be realized with only a 25% deterioration after 672 h of storage in air. Furthermore, we compare the photovoltaic performance of the P3HT:ICBA-based organic photovoltaic with PEDOT:PSS, and PEDOT:PSS:MoO_X, in which PEDOT:PSS:MoO_X has outperformed the others. In addition, the water vapor transmission rate of PEDOT:PSS:MoO_X is 0.17 gm/(m² day), which is much less than that of PEDOT:PSS.     

A highly conductive PEDOT:PSS film with the dipping treatment by hydroiodic acid as anode for organic light emitting diode

A highly conductive, transparent and uniform poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) film has been developed by dipping treatment with hydriodic acid (HI) solution. The HI-treated PEDOT:PSS film can reach a sheet resistance of 68 Ω per square and a transmittance of 87% at 550 nm. The conductivity enhancement for the HI-treated film is ascribed to the permeation of proton and iodine anion of HI into PEDOT:PSS film, resulting in the separation of PSS and PEDOT chains. The phase separation of PSS and PEDOT can provide more conductive pathways for carriers to improve conductivity of the film. Using the optimized HI-treated PEDOT:PSS film as anode, we have fabricated indium tin oxide (ITO)-free organic light emitting diode (OLED), which shows better performance than the device with ITO as anode. This proves that such PEDOT:PSS film with the dipping treatment by HI solution is a promising alternative to ITO for low cost, transparent and flexible OLED application.     

Transparent and flexible amorphous InZnAlO films grown by roll-to-roll sputtering for acidic buffer-free flexible organic solar cells

We report on transparent and flexible amorphous In–Zn–Al–O (a-IZAO) films prepared by roll-to-roll (RTR) sputtering for use as anodes in acidic buffer free flexible organic solar cells (FOSCs). The presence of Zn and Al structural stabilizers in the In₂O₃ matrix produced a completely amorphous structure with the high optical transmittance of 89.25% and the low resistivity of 2.123 × 10⁻³ Ω-cm, as well as the high work function of 5.14 eV, making the a-IZAO films suitable for use as flexible anodes for FOSCs. In addition, the a-IZAO films showed no change in resistance (ΔR) during outer and inner bending fatigue tests due to their good mechanical flexibility. Relative to the power conversion efficiency (1.944%) of a PEDOT:PSS-based FOSCs, a FOSC fabricated by using an a-IZAO anode and without the use of acidic PEDOT:PSS buffer showed greater power conversion efficiency (2.509%), owing to the absence of interfacial reactions between the acidic PEDOT:PSS and the a-IZAO anode.     

Composite film of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) and MoO3 as an efficient hole injection layer for polymer light-emitting diodes

We demonstrate improved performances in polymer light-emitting diodes (PLEDs) using a composite film of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and MoO₃ powder as a hole injection layer. The PLED with the composite film exhibits the current efficiency of 13.5 cd/A, driving voltage of 3.4 V, and half lifetime of 108.1 h, while those values of the PLED with a pristine PEDOT:PSS was 11.3 cd/A, 3.8 V, and 41.5 h, respectively. We also analyze the morphological, optical and electrical properties of the composite films by atomic force microscopy (AFM), UV–Vis-IR absorption, and ultraviolet photoemission spectroscopy (UPS). This work suggests that mixing MoO₃ into PEDOT:PSS is a simple and promising technique for use solution-based devices as an hole injection layer.     

Pt–free counter electrodes based on modified screen–printed PEDOT:PSS catalytic layers for dye–sensitized solar cells

One of the most highlighted advantages of dye-sensitized solar cells (DSSCs) consists in the possibility to apply simple and low-cost printing techniques and solution processable materials for their assembling. Here, we report on screen-printed Pt–free counter electrodes (CEs) based on poly(3,4–ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) dispersions with different content of rheological agent – hydroxyethyl cellulose (HEC). These PEDOT:PSS dispersions, having measured pseudoplastic and thixotropic rheological behaviour, were screen–printed onto FTO glasses. The content of rheological agent in PEDOT:PSS catalytic layers showed an effect on measured thickness, electrochemical properties, specific conductivity and subsequently on the evaluated photovoltaic performance of DSSCs. The PEDOT:PSS CE with the 0.03 wt% of HEC achieved the best electrochemical performance and specific conductivity (80 S cm⁻¹), the lowest thickness of 200 nm and transparency in VIS light spectrum over 60%. DSSCs based on this PEDOT:PSS CE reached the highest conversion efficiency of 4.2% which is only approximately 40% lower value than η=6.9% evaluated for Pt CE.     

ITO-free organic solar cells using highly conductive phenol-treated PEDOT:PSS anodes

Phenol as one of the most polar solvent was used to enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. The conductivity of PEDOT:PSS films improved to 1193 S/cm after treatment with phenol vapor and 1054 S/cm after treatment with phenol drop. The treated films also showed high transmittance in the visible region which is one of the crucial factors for optoelectronic devices such as organic solar cells and light emitting diodes. The mechanism of conductivity enhancement of treated thin PEDOT:PSS films was investigated by atomic force microscopy (AFM) and UV/Vis spectrophotometer. The AFM images showed that the ratio of PEDOT to PSS at top most of the surface was increased for treated film. Rearrangement of PEDOT segment throughout the film and hence conformational changes are the reasons for enhancement of conductivity. The modified PEDOT:PSS films were used as electrode for ITO-free organic solar cells (OSCs). These ITO-free OSCs showed almost equal operation to those for ITO electrodes.     

Handheld and automated ultrasonic spray deposition of conductive PEDOT:PSS films and their application in AC EL devices

In this contribution we explore the spray deposition technique to achieve smooth films based on the conductive polymer PEDOT:PSS. Two different spray systems were used and compared namely: (a) handheld airbrush and (b) automated ultrasonic spray system. For each system a number of parameters were pre-adjusted during coating control experiments such as spray head distance, angle and cone for airbrush as well as flow rate, power and focus for ultrasonic nozzle. Water-based solutions of PEDOT:PSS having 20% of N-methylpyrrolidone (NMP) were sprayed on glass substrates at temperatures ranging from 75 to 150 °C. The resulting films were further chemically treated with ethylene glycol (EG) and evaluated with respect to their morphological, electrical and optical properties. Before EG-treatment the ultrasonic spraying resulted in smoother films with conductivity up to 2–3.9 times higher than their airbrushed counterparts. Deposition temperature proved to have minor effect on the morphological and electro-optical properties of PEDOT:PSS films. On the other hand, the film conductivity was enhanced, peaking at 610.1 S cm⁻¹ for ultrasonic spraying, when further chemically modified by EG. IR microspectroscopy mapping analysis, Raman spectroscopy and XRD data indicated a phase-separation between PEDOT and PSS chains and increasing crystallinity in the ultrasonically sprayed films. The application of such PEDOT:PSS films as transparent electrode in flexible AC EL devices is demonstrated.     

An inverted,organic WORM device based on PEDOT:PSS with very low turn-on voltage

An organic Write-Once-Read-Many (WORM) device based on poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) as the active layer was fabricated with an inverted architecture. Insertion of an ultrathin layer of poly(methylmethacrylate) (PMMA) between the bottom electrode and the PEDOT:PSS resulted in a systematic and substantial decrease in turn-on voltage, from 7.0 V to less than 1.0 V. An optimal thickness of the PMMA layer was found to yield the lowest consistent turn-on voltage of ∼0.8 V, with 0.5 V being the lowest value of all fabricated devices. The switching mechanism was attributed to filamentary doping of the PEDOT:PSS. Insertion of the PMMA acted to protect the underlying ZnO from being etched by the acidic PEDOT:PSS as well as to improve its wetting properties. Devices were demonstrated on both ITO and aluminum bottom electrodes, with aluminum yielding the highest ON/OFF ratios in the study. Owing to their inverted architecture, the devices demonstrated good stability, and the retention time of the ON-state was determined to be greater than twenty months while stored in air for devices with ITO bottom electrodes. In addition to deposition via spin-coating, blade-coating was demonstrated as a viable processing technique for applications requiring rapid or large-area manufacturing.     

Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

Metal salt modified PEDOT:PSS as anode buffer layer and its effect on power conversion efficiency of organic solar cells

The effects of metal chlorides such as LiCl, NaCl, CdCl₂ and CuCl₂ on optical transmittance, electrical conductivity as well as morphology of PEDOT:PSS films have been investigated. Transmittance spectra of spun PEDOT:PSS layers were improved by more than 6% to a maximum of 94% in LiCl doped PEDOT:PSS film. The surface of the PEDOT:PSS films has exhibited higher roughness associated with an increase in the electrical conductivity after doping with metal salts. The improvement in the physical properties of PEDOT:PSS as the hole transport layer proved to be key factors towards enhancing the P3HT:PCBM bulk heterojunction (BHJ) solar cells. These improvements include significantly improved power conversion efficiency with values as high as 6.82% associated with high fill factor (61%) and larger short circuit current density (∼18 mA cm⁻²).     

In-situ modification of PEDOT:PSS work function using alkyl alcohols as secondary processing solvents and their impact on merocyanine based bulk heterojunction solar cells

The influence of a series of alkyl alcohols on the work function of PEDOT:PSS thin films is systematically investigated by Kelvin probe measurements. We show that the PEDOT:PSS work function can be increased stepwise from 5.2 eV for pristine PEDOT:PSS to 5.61 eV using either alcohols with different alkyl chain length or varying the amount of alcohol in mixtures with chlorobenzene. Moreover, we demonstrate the effect of work function modification on merocyanine based bulk heterojunction solar cells, resulting in improved values for the open-circuit voltage comparable to those obtained with high work function MoO₃. Thus, the processing method presented herein can potentially serve as a simple, alternative route to adjustable and high work function electrodes while maintaining processability from solution.     

Electrical characterization of inorganic-on-organic diode based InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS)

The electronic properties of metal–organic semiconductor-inorganic semiconductor diode between InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS) polymeric organic semiconductor film have been investigated via current–voltage and capacitance–voltage methods. The Al/PEDOT:PSS/p-InP contact exhibits a rectification behavior with the barrier height value of 0.98 eV and with the ideality factor value of 2.6 obtained from their forward bias current voltage (I–V) characteristics at the room temperature greater than the conventional Al/p-InP (0.83 eV, n = 1.13). This increase in barrier height and ideality factor can be attributed to PEDOT:PSS film formed at Al/p-InP interface.     

Transverse charge transport in inkjet printed poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS)

Transverse (z) alignment of PEDOT grains was demonstrated in inkjet printed PEDOT:PSS. This explained the superior transverse charge conduction mode in inkjet printed PEDOT:PSS films, best fitted by the Efros-Shklovskii 1D-VRH (variable range hopping) model in this study compared with spin coated PEDOT:PSS films, which have demonstrated layers of generally in-plane aligned PEDOT:PSS grains. The findings of this study, regarding the microstructure of inkjet printed PEDOT:PSS films and their transverse charge transport model, justify measurements of the transverse conductivity of inkjet printed films in this study being 600 times higher than that of spin coated films. In addition, it was found that the addition of 5 wt% DMSO in the printing PEDOT:PSS ink lowers the workfunction by 3% approximately.     

MoO3/Au/MoO3–PEDOT:PSS multilayer electrodes for ITO-free organic solar cells

The effect of the MoO₃–PEDOT:PSS composite layer in the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode on the power conversion efficiency of ITO-free organic solar cells (OSCs) was evaluated. The MoO₃ (30 nm)/Au(12 nm)/MoO₃–PEDOT:PSS (30 nm)/PEDOT:PSS structure showed ~7% more optical transmittance than the MoO₃ (30 nm)/Au (12 nm)/MoO₃(30 nm)/PEDOT:PSS structure at 550 nm wavelength. The OSCs using MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrodes as anodes showed a considerable improvement in power conversion efficiency (PCE), from 1.84% to 2.81%, comparable to ITO based OSCs with PCE of 2.89%. This improvement is attributed to the suppression of MoO₃ dissolution by the acidic hole transport layer (HTL) PEDOT:PSS on the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode, resulting in high J_sc, V_oc and FF of the OSCs. This composite based multilayer electrode was shown to be a promising replacement in ITO-free flexible optoelectronic devices.     

Effect of PEDOT–PSS resistivity and work function on PLED performance

The effect of a commonly used hole injection layer, poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT–PSS), on polymer light-emitting diode (PLED) performance has been investigated. A series of four different types of commercial PEDOT–PSS, with varying resistivity and work function were examined in devices with the structure Indium Tin Oxide (ITO)/PEDOT–PSS/High Molecular Weight Poly(n-vinylcarbazole) (PVKH): 30% N,N′-bis(3-methylphenyl)-N,N′-diphenylbenzidine (TPD)/Low molecular Weight Poly(n-vinylcarbazole) (PVKL): 40% 2-(4-Biphenyl)-5-(4-tert-butylphenyl)-1,2,4-oxadiazole (PBD): 8% Ir(ppy)₃. It was found that the PEDOT–PSS with the highest work function and resistivity produced the devices with the highest efficiencies; this is due to the improved hole injection effect, the decrease in electron leakage current and the prevention of pixel crosstalk. A maximum device current efficiency of 33.4 cd A⁻¹ has been achieved for the most resistive PEDOT; this corresponded to an external quantum efficiency (E.Q.E.) of 11%. Increasing the work function of the PEDOT used resulted in a 60% increase in E.Q.E. and device efficiency for PEDOTs in the same resistivity range. Drift–diffusion simulations, carried out using SEmiconducting Thin Film Optics Simulation software (SETFOS) 3.2, produced J–V curves in good agreement with the experimentally observed results; this allowed us to extract qualitative values for the effective device mobility along with the PEDOT work function and resistivity.     

The application of oxidative chemical vapor deposited (oCVD) PEDOT to textured and non-planar photovoltaic device geometries for enhanced light trapping

In organic photovoltaics (OPVs), active layer thicknesses are limited by exciton diffusion length. Thus, non-planar surfaces and device architectures are desired for enhancing the light absorption in OPVs. The oxidative chemical vapor deposition (oCVD) process enables the formation of conformal films of conducting polymers on complex surface structures. oCVD poly(3,4 ethylenedioxythiophene) (PEDOT) is demonstrated to be compatible with a wide range of nano- to macro-scale textured and non-planar architectures that have been demonstrated to enhance light absorption in photovoltaics by various mechanisms of light trapping, such as lengthening optical pathways and taking advantage of reflective light bouncing. Here, conformal oCVD (PEDOT) layers are demonstrated over submicron features including submicron nanowedges and nanocones (with 70–100 nm groove depth and 100 nm pitch) and square gratings (50–350 nm groove depth and 139–833.3 nm pitch). In contrast, solution-applied PEDOT:PSS exhibits blanketing, thinning at the top of the features, and welling up of material in the bottom of the features, thus failing to conformally coat the complex surfaces. The application of oCVD PEDOT to macro-scale 3D OPV architectures was also explored. Enhanced active layer absorbance is shown using tetraphenyldibenzoperiflanthene (DBP) as the absorbing layer over the PEDOT.