利用多效膜蒸馏技术浓缩硫酸和磷酸水溶液

利用自制中空纤维气隙式多效膜蒸馏组件进行了多效膜蒸馏过程浓缩稀硫酸和磷酸溶液的研究, 考察了膜入口温度、料液进口浓度和料液流量对渗透通量和造水比的影响。结果表明,膜入口温度升高时渗透通量和造水比增加;料液流量增加,渗透通量增加,而造水比随之降低;料液酸浓度增加,渗透通量和造水比均随之下降,且硫酸的影响更为显著。实验过程中渗透通量和造水比最高可达5.3 L/(m²·h)和11.5。在适当的操作条件下,该过程可将质量分数(下同)为2%的稀硫酸或稀磷酸溶液浓缩至40%以上,且渗透液最大的电导率仍小于200 μS/cm。以10%的硫酸溶液为料液,利用2个不同的膜组件进行了持续30 d的多效膜蒸馏过程稳定性实验研究,实验期间所用膜组件操作性能没有明显下降,没有观察到膜渗漏现象。     

多效膜蒸馏过程用于海水和浓海水的深度浓缩

研究了离子交换法选择性脱钙与多效膜蒸馏相结合用于海水淡化和淡化厂浓水深度浓缩的可行性。海水或浓海水中钙离子能脱除90%以上,可防止高倍数浓缩时海水中硫酸钙沉淀对膜造成污染。本文以膜通量、造水比和馏出液电导率为多效膜蒸馏过程的性能指标,研究了操作条件对过程性能的影响。膜通量最高可达6.07 L/(m2?h),造水比最高可达13.2;当海水浓缩至250 g/L时,馏出液的电导率小于200 μm/cm,膜通量和造水比仍可达3.61 L/(m2?h)和4.96。以除钙后的浓海水为料液,利用两种多效膜蒸馏组件分别进行了持续45天的操作稳定性实验研究,在试验期间膜组件性能没有明显下降。该研究结果表明,多效膜蒸馏结合选择性脱钙是适合于海水深度浓缩及资源综合利用的高效节能技术。     

新型气隙式膜蒸馏组件盐水浓缩的试验研究

利用新型气隙式膜蒸馏组件对氯化钠溶液进行膜蒸馏试验研究。考察了进料温度、流速、浓度对膜通量、造水比和截留率的影响。结果表明,膜通量和造水比随着进料温度T3升高而增大,随着进料浓度的增加而减小;料液流量增加时膜通量增大,造水比降低;试验过程中截留率基本保持不变,稳定在99.8%以上。当料液浓度为3.0%,进料温度T1为30.0℃,T3为95.0℃、流量为7.0 L/h时,膜通量为4.1 L/(m2·h),造水比为7.0,截留率可达99.8%,经过60 d浓缩试验后,膜通量、造水比和截留率均保持稳定。     

高温多效膜蒸馏用于处理高盐溶液的实验研究

膜蒸馏通常在温度低于90℃的条件下操作,而对于高盐溶液,由于浓差极化和饱和蒸气压下降比较明显,在通常操作温度下膜通量和热利用率都很低。采用具有内部潜热回收功能的多效膜蒸馏组件在高温操作条件下对以氯化钠为代表的无机盐浓溶液的深度浓缩进行了研究,着重考察了冷进料温度T1,加热后料液温度T3、浓度、流量等操作参数对膜通量、造水比和截留率的影响。结果表明,当料液质量分数为5%,热料液温度T3为100℃时,膜通量和造水比的值分别为3.1 L/(m2·h)和15.2;虽然膜通量和造水比均随料液浓度增大而下降,但是当料液质量浓度为25%,T3为105℃时,膜通量和造水比值仍可达1.53 L/(m2·h)和5.8;且截留率达到99.95%以上。在60 d的连续运行中,膜组件保持了良好的性能稳定性。结果表明高温多效膜蒸馏技术能够有效用于高盐溶液的深度浓缩。     

多效膜蒸馏技术用于果汁浓缩

利用自制的具有高效内部热量回收功能的多效膜蒸馏组件对西瓜汁、梨汁、柚子汁和苹果汁4种果汁进行了浓缩试验,考察了进料温度、浓度和料液流量对膜通量和造水比的影响。浓缩试验中选用温度为75℃的热水作为低品位热源以保障果汁经历的最高温度不超过70℃。在浓缩过程中膜平均通量约为3 L/（m2.h）,造水比约为7.5,相当于九效蒸发器的节能效果。选取苹果汁为料液,利用上述单因素、浓缩试验后的膜组件进行了周期为2个月的多效膜蒸馏浓缩操作稳定性试验,试验期间所用膜组件的操作性能没有明显下降。     

正渗透浓缩浓盐水影响因素研究初探

采用反渗透海水淡化后的浓盐水为原料液,考察了驱动液种类、切向流速(泵转速)、原料液浓度、活性层朝向等变量对正渗透过程水通量的影响。结果表明,在相同浓度下的驱动溶液,氯化钙作为驱动溶液产生的水通量最高;氯化纳次之;葡萄糖最小,但膜对氯化钠的截留率最高,随着驱动液浓度的增大,对应的水通量增大,但水通量的增加量随驱动液浓度的增大而减小;当膜的活性层朝向原料液(正渗透模式)时,初始水通量远小于膜的活性层朝向驱动液(压力阻尼渗透模式)的水通量,但在驱动液浓度相同时正渗透模式下的平均水通量更高。在切向流速达到1 L/min后,水通量受切向流速的影响较小。最后采用HTI膜在正渗透模式下以5 mol/L NaCl溶液为驱动液、切向流速为1 L/min的条件下连续运行进行浓缩,约30 h后,在原料液的容器壁上发现了少许的沉淀物,原溶液的Na Cl回收率可达到52.6%。     

平板膜污泥浓缩工艺中污染膜的膜清洗方式

该文研究了平板膜污泥浓缩工艺中污染膜的清洗,分析了不同种类、不同浓度化学药剂的清洗效果,重点评估了膜通量恢复率、膜表面形态、临界通量等性能。结果表明Na Cl O为最有效清洗药剂,清洗后膜水通量恢复最显著,膜表面孔隙率恢复最高,Na OH药剂不适宜于该工艺中膜的清洗。此外,试验确定0.1%草酸和1%Na Cl O的组合清洗方式为污泥浓缩工艺中膜清洗的最佳清洗方式,经组合清洗后的膜表面形态基本完全恢复,临界通量可高达32~35 L/m2·h。     

基于序批式MBR-RO的焦化废水深度处理研究

以实际焦化废水为研究对象,考察了序批式MBR-RO复合系统对该类废水污染物的处理效果。结果表明,序批式MBR-RO系统可成功应用于焦化废水常规预处理后的直接处理,COD去除率稳定在93%以上,反渗透出水COD平均为28.7 mg/L;TN去除率稳定在96%以上,反渗透出水TN平均质量浓度为4.53 mg/L。对于废水中酚类和氰化物的有毒污染物,MBR-RO系统出水质量浓度分别为0.24 mg/L和0.02 mg/L,反渗透浓缩倍数分别达到3.85倍和4.53倍,实现了该类有害物质的浓缩回收。此外,实验以膜的临界通量作为连续运行的初始条件,在连续60 d的运行过程中,MBR比膜通量损失65.3%,RO比膜通量损失73.2%。     

荷电中空纤维复合膜及其正渗透性能研究

以聚丙烯中空纤维微滤膜为底膜、羧甲基纤维素钠为功能材料、氯化铁为交联剂,采用溶液涂覆-交联工艺制备了表面荷电的中空纤维复合膜,将该中空纤维复合膜用于正渗透(FO)过程,研究了汲取液盐含量、原料液流速等对FO通量的影响。结果表明,制备的荷电中空纤维复合膜可用于FO过程,以蒸馏水为原料液、Na2SO4水溶液为汲取液,采用PRO模式进行FO试验,当原料液与汲取液体积流量均为15 mL/min、汲取液浓度为0.5 mol/L时,FO水通量为12.3 L/(m2.h),盐通量与水通量的比为1.42 g/L。     

高性能NaA沸石膜的制备及其脱盐性能

以廉价大孔α-Al_2O_3管为载体,通过两步变温热浸渍涂晶法,修饰载体表面缺陷,得到连续而均匀的晶种层。在微波辅助作用下,短时间内有效诱导制备出超薄Na A分子筛膜。将其用于渗透汽化脱盐体系中,研究发现,微波加热法制备的超薄Na A沸石膜水通量明显高于常规加热法制备的较厚Na A沸石膜,水的渗透通量随着盐浓度的增大在小范围内有所降低,而操作温度的升高对水的渗透具有明显促进作用,当原料液浓度为0.6mol/L、操作温度85℃时,水通量达到11.03kg/(m2·h)。同时,离子截留率不受操作温度及原料液浓度的影响,始终保持99.9%。此外,Na A沸石膜在渗透蒸发脱盐中表现出较高的稳定性,75℃条件下,在0.6mol/L的Na Cl溶液中性能可稳定72h以上。该方法在降低制膜成本的同时有效提高了水的渗透通量及离子截留率,表明Na A沸石膜在膜法脱盐的工业化应用领域具有较好的应用前景。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。