NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Mechanistic study of partial oxidation of methane to synthesis gas over supported rhodium and ruthenium catalysts using in situ time-resolved FTIR spectroscopy

In situ time-resolved FTIR spectroscopy was used to study the reaction mechanism of partial oxidation of methane to synthesis gas and the interaction of CH₄/O₂/He (2/1/45) gas mixture with adsorbed CO species over SiO₂ and γ-Al₂O₃ supported Rh and Ru catalysts at 500–600°C. It was found that CO is the primary product for the reaction of CH₄/O₂/He (2/1/45) gas mixture over H₂ reduced and working state Rh/SiO₂ catalyst. Direct oxidation of methane is the main pathway of synthesis gas formation over Rh/SiO₂ catalyst. CO₂ is the primary product for the reaction of CH₄/O₂/He (2/1/45) gas mixture over Ru/γ-Al₂O₃ and Ru/SiO₂ catalysts. The dominant reaction pathway of CO formation over Ru/γ-Al₂O₃ and Ru/SiO₂ catalysts is via the reforming reactions of CH₄ with CO₂ and H₂O. The effect of space velocity on the partial oxidation of methane over SiO₂ and γ-Al₂O₃ supported Rh and Ru catalysts is consistent with the above mechanisms. It is also found that consecutive oxidation of surface CO species is an important pathway of CO₂ formation during the partial oxidation of methane to synthesis gas over Rh/SiO₂ and Ru/γ-Al₂O₃ catalysts.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Deactivation and regeneration of hybrid catalysts in the single-step synthesis of dimethyl ether from syngas and CO2

Synthesis of dimethyl ether (DME) has been studied in a single reaction step, from H₂ + CO and H₂ + CO₂, in a fixed bed reactor on CuO-ZnO-Al₂O₃/γ-Al₂O₃ and CuO-ZnO-Al₂O₃/NaHZSM-5 hybrid catalysts. It has been proven that water content in the reaction medium (which is higher when CO₂ is fed) contributes to efficiently decreasing deactivation by coke in both catalysts and, consequently, when water is in the feed deactivation is insignificant for 30 h reaction. Nevertheless, water also decreases the activity of γ-Al₂O₃ acid function, due to its high adsorption capacity on the acid sites. Due to its importance in the viability of the industrial process, a study has been carried on the regeneration of both catalysts by coke combustion under controlled conditions (in order to avoid CuO sintering). For this study, the catalysts have been used under severe deactivation conditions. It has been proven that γ-Al₂O₃ does not have a suitable hydrothermal stability and that CuO-ZnO-Al₂O₃/NaHZSM-5 catalyst has an excellent performance and is suitable for using it in uninterrupted reaction–regeneration cycles.     

制备条件对NiMo/γ-Al2O3催化剂上萘加氢生成四氢萘的影响

采用等体积浸渍法制备加氢催化剂NiMo/γ-Al₂O₃,在悬浮床上考察不同的制备条件下NiMo/γ-Al₂O₃对萘加氢生成四氢萘的影响。结果表明,催化剂的制备条件对加氢活性有显著的影响,NiMo/γ-Al₂O₃催化剂的最佳制备条件为共浸渍法负载金属组分Ni和Mo,在500 ℃的温度下焙烧4 h。此条件下制备的催化剂上四氢萘的选择性高达95.2%。     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.     

Study of Ag/La0.6Sr0.4MnO3 catalysts for complete oxidation of methanol and ethanol at low concentrations

Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure were prepared by using a citric acid sol–gel method, and their catalytic performance for complete oxidation of methanol and ethanol was evaluated and compared with that of the γ-Al₂O₃-supported catalysts, Ag/γ-Al₂O₃, Pt/γ-Al₂O₃, and Pd/γ-Al₂O₃. The results showed that the Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure displayed the activity significantly higher than that of the supported precious metal catalysts, 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ in the temperature range of 370–573 K. Over a 6%Ag/20%La_0.6Sr_0.4MnO₃/γ-Al₂O₃ catalyst, the T₉₅ temperature for methanol oxidation can be as low as 413 K. Even at such low reaction temperature, there were little HCHO and CO detected in the reaction exit-gas. However, for the 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ catalysts, the HCHO content in the reaction exit-gas reached 200 and 630 ppm at their T₉₅ temperatures. Over a 6%Ag/La_0.6Sr_0.4MnO₃ catalyst, the T₉₅ temperature for ethanol oxidation can be as low as 453 K, with a corresponding content of CH₃CHO in the exit-gas at 782 ppm; when ethanol oxidation is performed at 493 K, the content of acetaldehyde in the exit-gas can be below 1 ppm. Characterization of the catalysts by X-ray diffraction (XRD), TEM, XPS, laser Raman spectra (LRS), hydrogen temperature-programmed reduction (H₂-TPR) and oxygen temperature-programmed desorption (O₂-TPD) methods revealed that both the surface and the bulk phase of the perovskite La_0.6Sr_0.4MnO₃ played important roles in the catalytic oxidation of the alcohols, and that γ-Al₂O₃ as the bottom carrier could be beneficial in creating a large surface area of catalyst. Moreover, a small amount of Ag⁺ doped onto the surface of La_0.6Sr_0.4MnO₃ was able to partially occupy the positions of La³⁺ and Sr²⁺ due to their similar ionic radii, and thus, became stabilized by the perovskite lattice, which would be in favor of preventing the aggregation of the Ag species on the surface and enhancing the stability of the catalyst. On the other hand, modification of the Ag⁺ to the surface of La_0.6Sr_0.4MnO₃ resulted in an increase in relative content of the surface O₂²⁻/O⁻ species highly reactive toward the alcohols and aldehydes as well as CO. Besides, solution of low-valence metal oxides SrO and Ag₂O with proper amounts in the lattice of the trivalent metal perovskite-type oxide LaMnO₃ would also lead to an increase in the content of the reducible Mnⁿ⁺ and the formation of anionic vacancies, which would be favorable for the adsorption-activation of oxygen on the functioning catalyst and the transport of the lattice and surface oxygen species. All these factors would contribute to the pronounced improvement of the catalyst performance.     

Kinetic studies of CH4 oxidation over Pt–NiO/δ-Al2O3 in a fluidised bed reactor

The oxidation of CH₄ over Pt–NiO/δ-Al₂O₃ has been studied in a fluidised bed reactor as part of a major project on an autothermal (combined oxidation–steam reforming) system for CH₄ conversion. The kinetic data were collected between 773 and 893 K and 101 kPa total pressure using CH₄ and O₂ compositions of 10–35% and 8–30%, respectively. Rate–temperature data were also obtained over alumina-supported monometallic catalysts, Pt and NiO. The bimetallic Pt–NiO system has a lower activation energy (80.8 kJ mol⁻¹) than either Pt (86.45 kJ mol⁻¹) and NiO (103.73 kJ mol⁻¹). The superior performance of the bimetallic catalyst was attributed to chemical synergy. The reaction rate over the Pt–NiO catalyst increased monotonically with CH₄ partial pressure but was inhibited by O₂. At low partial pressures (<30 kPa), H₂O has a detrimental effect on CH₄ conversion, whilst above 30 kPa, the rate increased dramatically with water content.     

Bound-state Ni species — a superior form in Ni-based catalyst for CH4/CO2 reforming

The effects of nickel loading, calcination temperature, support, and basic additives on Ni-based catalyst structure and reactivity for CH₄ reforming with CO₂ were investigated. The results show that the structure of the nickel active phase strongly depends on the interactions of the metal and the support, which are related to the support properties, the additives and the preparation conditions. “Free” Ni species can be formed when the interaction is weak and their mobility makes them easily deactivated by coking and sintering. The effect of strong metal-support interaction (SMSI effect) is different for various supports. The formation of solid solution of Ni–Mg–O₂ and the blocking of TiO_x by the partially reduced TiO₂ can both decrease the availability of Ni active sites in Ni/MgO and Ni/TiO₂. The spinel NiAl₂O₄ formed in Ni/γ-Al₂O₃ might be responsible for its high activity and resistance to coking and sintering because it can produce a highly dispersed active phase and a large active surface area as bound-state Ni species when the catalyst is prepared at high calcined temperatures or with low nickel loading. The addition of La₂O₃ or MgO as alumina modifiers can also be beneficial for the performance of the Ni/γ-Al₂O₃ catalyst.     

High combustion activity of methane induced by reforming gas over Ni/Al2O3 catalysts

During the reactions related to oxidative steam reforming and combustion of methane over -alumina-supported Ni catalysts, the temperature profiles of the catalyst bed were studied using an infrared (IR) thermograph. IR thermographical images revealed an interesting result: that the temperature at the catalyst bed inlet is much higher under CH₄/H₂O/O₂/Ar = 20/10/20/50 than under CH₄/H₂O/O₂/Ar = 10/0/20/70; the former temperature is comparable to that over noble metal catalysts such as Pt and Pd. Based on the temperature-programmed reduction and oxidation measurements over fresh and used catalysts, the metallic Ni is recognized at the catalyst bed inlet under CH₄/H₂O/O₂/Ar = 20/10/20/50, although it is mainly oxidized to NiAl₂O₄ under CH₄/H₂O/O₂/Ar = 10/0/20/70. This result indicates that the addition of reforming gas (CH₄/H₂O = 10/10) to the combustion gas (CH₄/O₂ = 10/20) can stabilize Ni species in the metallic state even under the presence of oxygen in the gas phase. This would account for its extremely high combustion activity.     

Catalytic conversion of methane and CO2 to synthesis gas over a La2O3-modified SiO2 supported Ni catalyst in fluidized-bed reactor

In this contribution, a commercial spherical SiO₂ was modified with different amounts of La₂O₃, and used as the support of Ni catalysts for autothermal reforming of methane in a fluidized-bed reactor. Nitrogen adsorption, XRD and H₂-TPR analysis indicated that La₂O₃-modified SiO₂ had higher surface area, strengthened interaction between Ni and support, and improved dispersion of Ni. CO₂-TPD found that La₂O₃ increased the alkalescence of SiO₂ and improved the activation of CO₂. Coking reaction (via both temperature-programmed surface reaction of CH₄ (CH₄-TPSR) and pulse decomposition of CH₄) disclosed that La₂O₃ reduced the dehydrogenation ability of Ni. CO₂-TPO, O₂-TPO (followed after CH₄-TPSR) confirmed that only part amount of carbon species derived from methane decomposition could be removed by CO₂, and O₂ in feed played a crucial role for the gasification of the inactive surface carbons. Ni/xLa₂O₃-SiO₂ (x = 10, 15, 30) possessed high activity and excellent stability for autothermal reforming of methane in a fluidized-bed reactor.     

K-, CeO2-, and Mn-promoted Ni/Al2O3 catalysts for stable CO2 reforming of methane

Reforming of methane with carbon dioxide into syngas over Ni/γ-Al₂O₃ catalysts modified by potassium, MnO and CeO₂ was studied. The catalysts were prepared by impregnation technique and were characterized by N₂ adsorption/desorption isotherm, BET surface area, pore volume, and BJH pore size distribution measurements, and by X-ray diffraction and scanning electron microscopy. The performance of these catalysts was evaluated by conducting the reforming reaction in a fixed bed reactor. The coke content of the catalysts was determined by oxidation conducted in a thermo-gravimetric analyzer. Incorporation of potassium and CeO₂ (or MnO) onto the catalyst significantly reduced the coke formation without significantly affecting the methane conversion and hydrogen yield. The stability and the lower amount of coking on promoted catalysts were attributed to partial coverage of the surface of nickel by patches of promoters and to their increased CO₂ adsorption, forming a surface reactive carbonate species. Addition of CeO₂ or MnO reduced the particle size of nickel, thus increasing Ni dispersion. For Ni–K/CeO₂–Al₂O₃ catalysts, the improved stability was further attributed to the oxidative properties of CeO₂. Results of the investigation suggest that stable Ni/Al₂O₃ catalysts for the carbon dioxide reforming of methane can be prepared by addition of both potassium and CeO₂ (or MnO) as promoters.     

Transient modeling of combined catalytic combustion/CH4 steam reforming

This paper presents an investigation into the complex interactions between catalytic combustion and CH₄ steam reforming in a co-flow heat exchanger where the surface combustion drives the endothermic steam reforming on opposite sides of separating plates in alternating channel flows. To this end, a simplified transient model was established to assess the stability of a system combining H₂ or CH₄ combustion over a supported Pd catalyst and CH₄ steam reforming over a supported Rh catalyst. The model uses previously reported detailed surface chemistry mechanisms, and results compared favorably with experiments using a flat-plate reactor with simultaneous H₂ combustion over a γ-Al₂O₃-supported Pd catalyst and CH₄ steam reforming over a γ-Al₂O₃-supported Rh catalyst. Results indicate that stable reactor operation is achievable at relatively low inlet temperatures (400 °C) with H₂ combustion. Model results for a reactor with CH₄ combustion indicated that stable reactor operation with reforming fuel conversion to H₂ requires higher inlet temperatures. The results indicate that slow transient decay of conversion, on the order of minutes, can arise due to loss of combustion activity from high-temperature reduction of the Pd catalyst near the reactor entrance. However, model results also show that under preferred conditions, the endothermic reforming can be sustained with adequate conversion to maintain combustion catalyst temperatures within the range where activity is high. A parametric study of combustion inlet stoichiometry, temperature, and velocity reveals that higher combustion fuel/air ratios are preferred with lower inlet temperatures (≤500 °C) while lower fuel/air ratios are necessary at higher inlet temperatures (600 °C).     

Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

Development of new catalysts for N2O-decomposition from adipic acid plant

Direct decomposition of N₂O was investigated using simulated and real industrial gas stream coming from an adipic acid plant. Two different kinds of catalysts were studied: (i) LaB_1−xB′_xO₃ and CaB_1−xCu_xO₃ (B = Mn, Fe and B′ = Cu, Ni) perovskites (PVKs) and (ii) supported PVKs (10 or 20 wt.%) on γ-Al₂O₃ and CeO₂–ZrO₂. The structural modifications induced by the composition of PVK samples affect the catalytic performances: mixed oxide formation in CaMn_0.7Cu_0.3O₃ samples allows to reach the highest values of N₂O conversion while the effect of PVK phases is more controversial. The importance of copper on catalytic activities is confirmed by the investigation on CaMn_1−xCu_xO₃ samples. The best results were obtained with a CaMn_0.6Cu_0.4O₃ catalyst calcined at 700 °C for 5 h, in which the presence of copper maximises the Ca₃CuMnO₆ phase formation. The increase in Cu-content produces a large segregation of CuO despite PVK formation. The best catalyst was tested using industrial gas stream, showing good stability also in the presence of H₂O and O₂ (8% v/v ) after 1400 h on-stream. To increase surface area, Cu-containing PVKs were deposed on γ-Al₂O₃ and CeO₂–ZrO₂, and this latter has been recognised as the best support. Indeed, the activity of the PVKs supported on ceria–zirconia is comparable to and even better than that of the bulk catalysts. A possible explanation regards the support contribution in terms of activity and/or promotion of O₂ mobility which enhances the overall activity of the catalyst.     

Influence of the co-feeding of CO, H2, CO2 or H2O in the partial oxidation of methane over Ni and Rh supported catalysts

The influence of the addition of 5 vol.% of carbon monoxide, hydrogen, carbon dioxide or water to the feed of partial oxidation of methane was investigated over Ni/γ-Al₂O₃ and Rh/γ-Al₂O₃ catalysts. In addition to catalytic tests, thermodynamic calculations were performed to predict the effect of these gas co-feeds. Compared to the thermodynamic trends, differences in the influence of the co-feeding on catalytic performances were observed between both catalysts. Co-feeding of CO, H₂, CO₂ or H₂O can modify the oxidation state and dispersion of the metal component of the catalysts during reaction, and as a consequence, their performances. Changes in catalysts can be due to dynamic processes occurring during reaction. It is suggested to take these processes into account in a more complex kinetic equation for the reactions involved.     

Preparation and structural characterization of Co/Al2O3 catalysts for the ozonation of pyruvic acid

A series of Co/Al₂O₃ catalysts were prepared by the incipient wetness impregnation method using γ-Al₂O₃ support and (CH₃COO)₂Co·4H₂O solutions, followed by calcination at 500–800 °C. Characterization of catalysts was accomplished by several techniques such as thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), physisorption of nitrogen, mercury and helium-based pycnometries, Fourier transform-infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and pH of zero charge (PZC). Impregnation of support produced a moderate decrease of its surface area and pore volume and also led to minor changes of its PZC. Depending on preparation conditions (i.e., calcination atmosphere and temperature and metal loading), one or more of the following Co-containing compounds were identified: CoO, Co₃O₄ and CoAl₂O₄. The support and prepared Co/Al₂O₃ catalysts were tested to catalyze the ozonation of aqueous pyruvic acid at pH 2.5. Pyruvic acid was shown refractory towards single ozonation but the use of γ-Al₂O₃ and Co/Al₂O₃ catalysts resulted in 56–96% pyruvic acid conversion and 41–78% decrease in DOC after 2 h of ozonation of phosphate-buffered solutions. In the absence of the buffer, conversion rate was enhanced likely as a result of pH increase during the course of the process thus giving rise to the indirect way of ozonation through hydroxyl radicals. Acetic acid was found as the main by-product of pyruvic acid ozonation. Depending on the catalyst used, yield of acetic acid varied from 32 to 49%, values noticeably lower that that obtained from the control non-catalytic ozonation experiment (73%). Differences in catalytic activity amongst the various Co/Al₂O₃ catalysts investigated were attributed to the different Co active phases deposited on the γ-Al₂O₃ surface. The following sequence of increasing activity can be inferred from experimental results: CoO, CoAl₂O₄ and Co₃O₄. All the Co/Al₂O₃ catalysts prepared showed good stability as the percentage of cobalt leached out was rather low.     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

The effect of CeO2 structure on the activity of supported Pd catalysts used for methane steam reforming

Palladium (Pd) supported on CeO₂-promoted γ-Al₂O₃ with various CeO₂ (ceria) crystallinities, were used as catalysts in the methane steam reforming reaction. X-ray diffraction (XRD) analysis, FTIR spectroscopy of adsorbed CO, and X-ray photoelectron spectroscopy (XPS) were employed to characterize the samples in terms of Pd and CeO₂ structure and dispersion on the γ-Al₂O₃ support. These results were correlated with the observed catalytic activity and deactivation process. Arrhenius plots at steady-state conditions are presented as a function of CeO₂ structure. Pd is present on the oxidized CeO₂-promoted catalysts as Pd⁰, Pd⁺ and Pd²⁺, at ratios strongly dependent on CeO₂ structure. XRD measurements indicated that Pd is well dispersed (particles <2 nm) on crystalline CeO₂ and is agglomerated as large clusters (particles in 10–20 nm range) on amorphous CeO₂. FTIR spectra of adsorbed CO revealed that after pre-treatment under H₂ or in the presence of amorphous CeO₂, partial encapsulation of Pd particles occurs. CeO₂ structure influences the CH₄ steam reforming reaction rates. Crystalline CeO₂ and dispersed Pd favor high reaction rates (low activation energy). The presence of CeO₂ as a promoter conferred high catalytic activity to the alumina-supported Pd catalysts. The catalytic activity is significantly lower on Pd/γ-Al₂O₃ or on amorphous (reduced) CeO₂/Al₂O₃ catalysts. The reaction rates are two orders of magnitude higher on Pd/CeO₂/γ-Al₂O₃ than on Pd/γ-Al₂O₃, which is attributed to a catalytic synergism between Pd and CeO₂. The low rates on the reduced Pd/CeO₂/Al₂O₃ catalysts can be correlated with the loss of Pd sites through encapsulation or particle agglomeration, a process found mostly irreversible after catalyst regeneration.     

Coke study on MgO-promoted Ni/Al2O3 catalyst in combined H2O and CO2 reforming of methane for gas to liquid (GTL) process

MgO-promoted Ni/Al₂O₃ catalysts have been investigated with respect to catalytic activity and coke formation in combined steam and carbon dioxide reforming of methane (CSCRM) to develop a highly active and stable catalyst for gas to liquid (GTL) processes. Ni/Al₂O₃ catalysts were promoted through varying the MgO content by the incipient wetness method. X-ray diffraction (XRD), BET surface area, H₂-temperature programmed reduction (TPR), H₂-chemisorption and CO₂-temperature programmed desorption (TPD) were used to observe the characteristics of the prepared catalysts. The coke formation and amount in used catalysts were examined by SEM and TGA, respectively. H₂/CO ratio of 2 was achieved in CSCRM by controlling the feed H₂O/CO₂ ratio. The catalysts prepared with 20 wt.% MgO exhibit the highest catalytic performance and have high coke resistance in CSCRM. MgO promotion forms MgAl₂O₄ spinel phase, which is stable at high temperatures and effectively prevents coke formation by increasing the CO₂ adsorption due to the increase in base strength on the surface of catalyst.