Ultra-wideband bandpass filter using hybrid quasi-lumped elements and defected ground structure

A compact planar microstrip ultra-wideband (UWB) bandpass filter is presented. The proposed UWB filter is realised by cascading a highpass filter (HPF) and a lowpass filter (LPF). Additional U-slot defected ground structure is adopted to improve the attenuation performance in the stop band. The HPF consists of inter-digital capacitors and a short-circuited stub. The LPF achieved by a hybrid microstrip and four backside slots on the ground plane is equivalent to a typical 9-pole stepped-impedance LPF. Combining these two structures, a new UWB bandpass filter is fabricated and measured. Measured results show that the proposed bandpass filter has a wide bandwidth from 3.1 to 11 GHz, and insertion loss is less than 1.2 dB over the most central passband. It also achieves a wide stop band with 20 dB attenuation up to 20 GHz.     

Planar microstrip UWB bandpass filter using U-shaped slot coupling structure

A compact planar microstrip UWB bandpass filter is proposed. It is realised by cascading a lowpass filter and a highpass filter. A transmission line with U-shaped slots coupled with two DGS units on the back of the circuit board has the characteristic of highpass, while a periodic uniform DGS array has the characteristic of lowpass. Combining these two structures, a new UWB bandpass filter (BPF) is fabricated and measured. Measured results show that the proposed BPF has wide bandwidth from 3.0 to 10.9 GHz, all the measured return loss less than 13 dB in the passband. The BPF achieves a wide stopband with 18 dB attenuation up to 18.0 GHz     

基于新型谐振器的超宽带带通滤波器

采用两个新型四阶阶梯阻抗谐振器设计出一种新型超宽带带通滤波器,四个1/4波长的耦合线被平行放置于输入输出端,起到增加耦合强度的作用,三个谐振频率被调整在超宽带带宽(3.1 GHz～10.6 GHz)内。通过优化后,该滤波器在通带内具有五个传输极点,频带宽度在3.6 GHz～10.5 GHz,通带内回波损耗优于15 dB,最小插入损耗为0.6 dB,满足超宽带的传输要求。仿真结果显示,文中设计的滤波器具有小型化、低插入损耗和较好的带外特性等优点。     

Small Ultra-Wideband (UWB) Bandpass Filter With Notched Band

A compact ultra-wideband (UWB) bandpass filter (BPF) with notched band has been proposed and implemented in this letter. H-shaped slot is studied and adopted to tighten the coupling of inter-digital capacitor in order to improve the BPF's performance. Three pairs of tapered defected ground structures (DGS) are formed to assign their transmission zeros towards the out of band signal, thereby suppressing the spurious passband. Combining these two structures we obtain a small sized UWB BPF. Meander line slot is developed to reject the undesired wireless local-area network (WLAN) radio signals. An experimental UWB filter with notched band was fabricated with 35% less length as compared to an embedded open-circuited stub. The measured BPF insertion loss is less than 1.0 dB throughout the pass band of 2.8 to 10.8 GHz, the variation of group delay less than 0.20 ns in this band except for the notched band, and a wide stopband bandwidth with 20 dB attenuation up to at least 20.0 GHz.     

Dual-band UWB bandpass filter with triangular DB-DGS for WLAN applications in DSRC band

A dual-band Ultra-wideband (UWB) bandpass microstrip filter with triangular dumbbell shaped defected ground structure (DB-DGS) for wireless local area network applications in DSRC band is proposed in this article. The proposed dual-band filter has center frequencies at 2.67 GHz and 4.68 GHz, return loss obtained is −33.40 dB and −16.55 dB respectively, wide bandwidth of 1.21 GHz (26%), pass band between 2.14 GHz and 6.44 GHz and high gain of 10.30 dB which makes it suitable for modern applications in dedicated short range communication operating in 5.8 GHz band. To further validate the design concept, a microstrip UWB filter is designed, fabricated and tested. Comparison is made among circular, square and triangular dumbbell shaped DGS on the basis of scattering parameters and bandwidth, in which triangular shaped DB-DGS outperforms the other two. Further, parametric analysis of triangular DB-DGS has been performed and comparison is made with filters of similar nature. Experimental results are in good agreement with simulations. The fabricated filter is compact in size, has low insertion loss, exhibits high selectivity and demonstrates excellent out of-band performance.     

一种新型超宽带小型化U型微带滤波器

提出了一种新型超宽带(UWB)小型化微带滤波器。这种结构采用多个短路支节并联于主传输线上,短路支节长度为四分之一波长。采用一种新型等效电路对其进行分析、模拟,其中的主传输线、并联支节线以及T型结、拐角、接地孔等不连续处均等效为相应的电路元件,并结合适当的U型电路变形。通过精确建模、仿真,使这种新型结构的滤波器具有更小的体积和更宽的通带。采用0.762 mm厚RT Duriod 6002板材实际制作一个通带为3～21 GHz的超宽带微带滤波器,尺寸为12 mm×21 mm×0.762 mm。该滤波器不仅体积小,且性能优良,其带内损耗小于2.1 dB,回波损耗优于-8.2 dB。实做通带2.96～21.01 GHz,带宽达150.6%,与仿真结果较为吻合,可以满足工程应用的需要。     

基于CRLH TL结构的带通滤波器设计与研究

基于复合左右手传输线（CRLH TL）原理,利用微带与共面波导组合的双层介质结构,设计了一种新型带通滤波器。其等效左手电容由金属 绝缘体 金属（MIM）耦合结构提供,等效左手电感由蘑菇型零阶谐振器（MZOR）中的短路通孔实现。通过研究MZOR中U型槽长度变化对滤波器性能的影响得知,该带通滤波器具有结构紧凑,带宽较大,插入损耗较小等优点。HFSS仿真结果显示,滤波器的通带为3.4~7.2 GHz,通带内插入损耗低于-0.5 dB,回波损耗小于-11.5 dB。因此,该滤波器可应用于超宽带无线通信系统。     

Improved and compact 0.7 GHz tune-all bandpass filter

A compact tune-all bandpass filter is presented. This electronically tuned filter is based on series-coupled slow-wave resonators. It allows wide simultaneous and continuous tunings of centre frequency (+/-15% around 0.7 GHz) and bandwidth (from 50 to 100 MHz) with insertion loss IL<5.4 dB and return loss RL>11 dB. This two-pole bandpass filter exhibits also a very small surface of only 7.3times10^-3 lambda₀ ² and a -20 dB stop-band that extends up to 10 GHz     

Compact UWB Bandpass Filter Using Stub-Loaded Multiple-Mode Resonator

A compact microstrip-line ultra-wideband (UWB) bandpass filter (BPF) using the proposed stub-loaded multiple-mode resonator (MMR) is presented. This MMR is formed by loading three open-ended stubs in shunt to a simple stepped-impedance resonator in center and two symmetrical locations, respectively. By properly adjusting the lengths of these stubs, the first four resonant modes of this MMR can be evenly allocated within the 3.1-to-10.6 GHz UWB band while the fifth resonant frequency is raised above 15.0GHz. It results in the formulation of a novel UWB BPF with compact-size and widened upper-stopband by incorporating this MMR with two interdigital parallel-coupled feed lines. Simulated and measured results are found in good agreement with each other, showing improved UWB bandpass behaviors with the insertion loss lower than 0.8dB, return loss higher than 14.3dB, and maximum group delay variation less than 0.64ns in the realized UWB passband     

Compact ultra-wideband bandpass filter using broadside coupled hairpin structures on multilayer liquid crystal polymer substrate

A novel ultra-wideband (UWB) bandpass filter (BPF) using a broadside- coupled hairpin structure and multilayer organic liquid crystal polymer (LCP) technology is presented. To suppress stopband harmonic response, folded stepped impedance structures were adopted as hairpin resonators in the design. The proposed filter has been investigated numerically and experimentally. Multilayer LCP technology was used to implement designed UWB BPF. Good agreement between simulated and measured results of the proposed filter was observed. They show that the fabricated UWB BPF has a good performance, including a small insertion loss, a flat group delay with a variation within 0.1 ns in most of its passband, a wide stopband from 11.0 20.0 GHz with a high rejection level up to 20.0 dB, and a very compact size of 9.8 x 7.5 mm (0.36 lg x 0.27lg, where lg is the guided wavelength of 50 V microstrip line at 6.85 GHz).     

宽阻带小型化双频带通滤波器

文中提出了一种具有宽阻带的紧凑型双频带通滤波器,它采用了折叠短路枝节负载谐振器、紧凑型微 带单元谐振器(CMRC)和阶跃阻抗谐振器结构。由于多个谐振器产生了五个可控传输零点(TZ),该滤波器实现了两个 通带之间的良好隔离度以及宽阻带特性。制作并测试了尺寸紧凑的双频带通滤波器实验样品,测试结果显示,第一通 带和第二通带的中心频率/ 插入损耗分别为0. 66 GHz/0. 8 dB 和1. 73 GHz/0. 7 dB,阻带频率高达10. 5 GHz,抑制水平 超过15 dB。     

Compact UWB bandpass filter using ring open stub loaded multiple-mode resonator

A novel ultra-wideband (UWB) bandpass filter with a compact size, improved upper-stopband performance and reduced radiation loss has been studied and designed using a multiple-mode resonator (MMR). The MMR is formed by attaching three pairs of ring open stubs in shunt to a high impedance microstrip line. By simply adjusting the radius of the circles of the ring stubs, the resonant modes of the MMR can be roughly allocated within the 3.1?10.6 GHz UWB band while suppressing the spurious harmonics in the upper-stopband. Meanwhile, the insertion loss is higher than 20.0 dB in the upperstopband from 11.7 to 33.5 GHz in simulation. Finally, the filter is fabricated and measured. The EM-simulated and measured results are presented and excellent agreement between them is obtained.     

Design of compact low pass filter with wide stop band using tri-section stepped impedance resonator

This paper reports the design of a compact low pass filter (LPF) with wide stop band region using tri-section stepped impedance resonators in microstrip medium. Experimental results of a low pass filter designed at 1 GHz have been compared against the analytical and EM simulation results for the validation of the design. Results are satisfactorily matching each other. The maximum insertion of the measured filter is 0.2 dB and minimum return loss is 13.5 dB over the pass band. The stop band rejection is better than 20 dB from 1.5 GHz to 4.2 GHz and hence wide stop band performance is achieved. Overall size of the filter is 30 mm × 20 mm × 0.78 mm which is 0.1λ × 0.066λ × 0.0026λ at 1 GHz.     

A compact planar ultra-wideband bandpass filter with multiple resonant and defected ground structure

A compact bandpass filter with dumbbell shape Defected Ground Structure (DGS) operating on ultra wide pass band (UWB – 3.1 to 10.6 GHz) is proposed. It is based on hybrid microstrip coplanar waveguide (dual sided metal) structure. A Multiple Resonant Structure (MRS) is constructed using coplanar waveguide (CPW) planar transmission line. The MRS makes the resonance using quarter wavelength and half wavelength open-ended CPW. The equispaced three resonances at lower (3.1 GHz), center (6.85 GHz) and higher edge (10.6 GHz) of the whole Ultra Wide Band is achieved using CPW MRS. To make the band as flat as possible, two more resonances are introduced using quarter wavelength microstrip patches on top of the commonly shared substrate, so the proposed filter becomes a five pole bandpass filter. A dumbbell shaped defected ground structure on either side of CPW MRS improves the return loss almost less than 20 dB over the whole UWB passband. The simulated results of proposed filter show good transmission response within passband and good rejection in out of the band. The simulated and measured results are very close to each other which proves the efficacy of proposed design.     

Compact wide stopband lowpass filter using spiral loaded tapered compact microstrip resonator cell

A new spiral loaded tapered compact microstrip resonator cell (SPLT-CMRC) is presented. The addition of spiral stubs to the CMRC creates transmission zeroes in the stopband which extended the stopband of the ?lter. The proposed resonator is used to design a compact lowpass ?lter (LPF) with wide and high rejection in stopband. The fabricated ?lter has a 3 dB cutoff frequency at 8 GHz. The insertion loss in the passband is less than 0.2 dB from DC to 7.2 GHz. The proposed ?lter has wide stopband from 9.47 to 40 GHz with attenuation level of ?20 dB. The demonstrated filter is designed and fabricated. There is a good agreement between the measured and simulated S-parameters.     

一种具有陡峭边带的宽带带通滤波器设计

基于一种新型的多模谐振器设计了一款宽带带通滤波器,该多模谐振器由鱼骨形谐振器及中心加载倒T形谐振器构成。滤波器的中心频率位于2.47 GHz,相对带宽为100%。滤波器具有极高的频率选择性,其边带滚降速度分别为232 dB/GHz和168 dB/GHz。此外,滤波器还具有较低插入损耗0.4 dB,紧凑的电路尺寸以及宽阻带抑制能力。     

Microstrip Lowpass Filter with Very SharpTransition Band Using T‐Shaped,Patch, and Stepped Impedance Resonators

A compact microstrip lowpass filter (LPF) with an elliptic function response is proposed. A high equivalent capacitance and inductance between the structures of the resonator result in the sharp transition band of 0.04 GHz from 4 GHz to 4.04 GHz with an attenuation level of ?3 dB and ?20 dB, respectively. To improve the LPF rejection band, multiple open stubs are connected to the proposed resonator. A filter with a 3‐dB cut‐off frequency at 4 GHz is designed, fabricated, and measured, and agreement between the measured and simulated results is achieved. The results show that a stopband bandwidth of 131% with a suppression level better than ?20 dB is obtained while achieving a compact size with a wide stopband.     

Wide-stopband microstrip low-pass filter using modified semi-circle patch resonator

In this article, a compact microstrip low-pass filter with elliptic-function response is proposed. To achieve wide stopband, modified semi-circle patch resonator in series with semi-circle stepped impedance resonator is used. The proposed structure achieves a wide stopband and a high selectivity within a small circuit area. The proposed filter has 3-dB cutoff frequency at 1.71?GHz and 20?dB rejection at 2.1?GHz. The stopband with the attenuation level better than ?18.7?dB is from 2.08 up to 16?GHz, and consequently we have reached the high and wide rejection in stopband as well as compact size. The structure is simulated, fabricated and measured. The measured results are in good agreement with the simulated results.     

Compact UWB Bandpass Filter With Improved Upper-Stopband Performance

In this letter, a novel ultra-wideband (UWB) bandpass filter with compact size and improved upper-stopband performance has been studied and implemented using multiple-mode resonator (MMR). The MMR is formed by attaching three pairs of circular impedance-stepped stubs in shunt to a high impedance microstrip line. By simply adjusting the radius of the circles of the stubs, the resonant modes of the MMR can be roughly allocated within the 3.1-10.6 GHz UWB band while suppressing the spurious harmonics in the upper-stopband. In order to enhance the coupling degree, two interdigital coupled-lines are used in the input and output sides. Thus, a predicted UWB passband is realized. Meanwhile, the insertion loss is higher than 30.0 dB in the upper-stopband from 12.1 to 27.8 GHz. Finally, the filter is successfully designed and fabricated. The EM-simulated and the measured results are presented in this work where excellent agreement between them is obtained.     

Ultra Wideband Bandpass Filter Using Embedded Stepped Impedance Resonators on Multilayer Liquid Crystal Polymer Substrate

This letter proposes an ultra wideband (UWB) bandpass filter (BPF) based on embedded stepped impedance resonators (SIRs). In this study, broad side coupled patches and high impedance microstrip lines are adopted as quasi-lumped elements for realizing the coupling between adjacent SIRs, which are used to suppress stopband harmonic response. An eight-pole UWB BPF is developed from lump-element bandpass prototype and verified by full-wave simulation. The proposed filter is fabricated using multilayer liquid crystal polymer (LCP) process and measured using vector network analyzer. Good agreement between simulated and measured response is observed. The measurement results show that the fabricated filter has a low insertion loss of 0.18 dB at center frequency 6.05 GHz, an ultra wide fractional bandwidth of 127.3% and excellent stopband rejection level higher than 32.01 dB from 10.9 to 18.0 GHz.