非热等离子体协同Mn-Ce/La/γ-Al2O3催化剂去除甲苯

采用自制线管式介质阻挡放电反应器,针对非热等离子体协同Mn-Ce/La/γ-Al₂O₃催化剂对低浓度甲苯的去除开展研究。研究中制备了Mn/γ-Al₂O₃、Mn-Ce/γ-Al₂O₃、Mn-La/γ-Al₂O₃催化剂,从甲苯去除率、产物O₃生成、CO_x选择性及其他副产物生成情况考察比较了空管放电、协同催化剂放电时催化降解甲苯性能,并对催化剂进行了BET、SEM、H₂-TPR和ICP-OES表征研究。结果表明：稀土助剂的加入有助于提高甲苯去除率及降低程度,且La催化性能优于Ce_.,当外加电压22 kV、气量6 L·min^-1、甲苯初始浓度600 mg·m^-3时,Mn-La/γ-Al₂O₃催化剂对甲苯去除率达到72.74%。H₂-TPR结果表明,稀土助剂的加入提高了催化剂低温活性及储氧能力,添加La的效果优于Ce。催化剂有助于抑制副产物O₃生成,提高CO₂和CO_x选择性。     

Fe2O3/AC催化剂的低温选择性催化还原脱硝性能

以活性焦(AC)为载体、Fe2O3为活性组分,采用等体积浸渍法制备Fe2O3/AC催化剂,研究了Fe含量对Fe2O3/AC催化剂低温脱硝性能的影响. 结果表明,当Fe负载量为6wt%时能获得比其它负载量更佳的NOx转化率,尤其在240℃时NOx转化率达93.9%,当分别有120?10?6(vol) SO2和3.5vol H2O存在时,脱硝率分别稳定在约86%和74%;催化剂孔径≤4 nm,随Fe负载量增加,孔径呈增大趋势;催化剂较稳定;Fe主要以γ-Fe2O3分散在催化剂表面,负载适量Fe2O3使表面吸附氧Oβ和Fe3+增多,为催化剂提供更多活性位,提高了Fe2O3/AC催化剂的低温选择性催化还原脱硝活性.     

柠檬醛在La2O3/γ-Al2O3催化剂上的等温吸附

对柠檬醛-乙酸乙酯溶液中柠檬醛在La₂O₃/γ-Al₂O₃催化剂上等温吸附行为进行了研究。结果表明,30 ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的吸附动力学符合准二阶吸附动力学模型,吸附动力学方程为：1/q_t=2.350/t+0.063 3(R²=0.998 5)。（30~65） ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的等温吸附符合Langmuir方程,温度升高使柠檬醛的饱和吸附量增加,吸附热为32.19 kJ·mol^-1。     

Co/γ-Al2O3催化乙酰丙酸加氢合成γ-戊内酯的研究

采用等体积浸渍法制备一系列Co负载量不同的Co/Al₂O₃催化剂,用于乙酰丙酸液相催化加氢制γ-戊内酯反应。采用X射线衍射仪和透射电镜对Co/Al₂O₃催化剂进行表征,考察Co负载量、反应温度、反应压力和催化剂用量等对乙酰丙酸液相催化加氢反应的影响。结果表明,在Co负载质量分数15%、反应温度140 ℃、反应压力4.0 MPa和催化剂用量为反应物总质量的20%条件下,以甲醇为溶剂,反应6 h,乙酰丙酸转化率100%,γ-戊内酯选择性80.4%。催化剂重复使用6次仍具有较好的催化性能。     

镍对Pt/γ-Al2O3催化剂稠环芳烃选择性加氢性能的影响

分别以氯铂酸和硝酸镍为铂和镍前驱体,通过等体积浸渍法制备了系列镍修饰的Pt/γ-Al₂O₃催化剂,并采用电感耦合等离子体原子发射光谱（ICP-AES）、氨程序升温脱附（NH₃-TPD）、氢气程序升温还原（H₂-TPR）、氢气程序升温脱附（H₂-TPD）及氢氧滴定法（H₂-O₂）等手段进行表征。以重整C₁₀⁺重芳烃为原料,在30 mL固定床装置上考察镍引入对Pt/γ-Al₂O₃催化剂稠环芳烃（PAHs）选择性加氢性能的影响。固定床评价结果表明,随镍含量增加,稠环芳烃加氢活性和单环芳烃选择性呈现先增加后降低的趋势,当0.1Pt/γ-Al₂O₃催化剂中引入0.5%（质量分数）的镍时,催化剂稠环芳烃加氢活性和选择性最佳,此时稠环芳烃转化率为75%左右,单环芳烃选择性为98%以上。结合H₂-TPR、H₂-TPD及H₂-O₂滴定等表征结果,分析主要原因在于一定量镍的引入提高了铂的分散度,同时由于铂的加氢活化能较低,铂通过溢流活化的氢迁移至非贵金属镍上,提高了金属镍的加氢性能。此外,铂的存在还可避免镍形成尖晶石结构等非活性相,促进镍氧化物的还原,进而提高了催化剂的稠环芳烃加氢活性、选择性和稳定性。     

CeO2改性Ni/γ-Al2O3催化剂上顺酐加氢制备丁二酸酐

采用等体积浸渍法制备CeO₂改性Ni/γ-Al₂O₃催化剂,通过BET、XRD、H₂-TPR和SEM等对催化剂结构及物化性能进行表征,考察Ni-CeO₂/γ-Al₂O₃催化剂对顺酐催化加氢制备丁二酸酐催化性能的影响。结果表明,引入适量CeO₂可提高催化剂活性组分Ni的分散度,增加催化剂比表面积,提高催化剂热稳定性。采用负载CeO₂质量分数5%的Ni-CeO₂/γ-Al₂O₃催化剂,在反应温度120 ℃、反应压力2.0 MPa和空速0.6 h^-1条件下,顺酐转化率为99.5%,丁二酸酐选择性为99.4%。     

Au/α-Fe2O3催化剂选择性氧化富氢气中CO的性能研究

通过并流共沉淀法制备了Au/-Fe2O3催化剂,考察了金负载量及焙烧温度对Au/-Fe2O3催化剂的物化结构及其选择性氧化富氢气体中CO催化性能的影响。研究结果表明,金负载量和焙烧温度对催化剂的性能均有较大影响,金负载量为1.5%(wt),低温焙烧(200~400℃)时制得的Au/-Fe2O3催化剂对CO选择性氧化反应具有很好的催化活性和选择性,其中金负载量为1.5%(wt)、300℃焙烧的Au/-Fe2O3催化剂,在40℃时对富氢气体中CO的转化率达到100%,选择性为 66%,该催化剂连续反应120h催化活性没有明显下降。XRD、BET和TEM分析结果表明,催化剂的性能与单质Au的粒径有关,粒径越小,催化活性越高。     

Co-Cu-Ce-Fe/γ-Al_2O_3催化剂催化分解N_2O的性能

以等体积浸渍法制备γ-Al_2O_3负载的Co、Cu、Ce和Fe氧化物催化剂,利用正交试验设计实验条件,采用XRD、BET和H_2-TPR等对催化剂进行表征,并考察活性组分对催化剂催化分解N_2O活性的影响。结果表明,催化剂具有尖晶石结构,其BET比表面积随着金属氧化物负载量增加而降低。催化剂中铜的氧化物可以降低还原峰温度,进而明显提高催化活性,Co和Fe的加入对活性有一定的提高,Ce对催化活性没有明显影响。     

α-Fe2O3纳米材料的制备及性能研究

以氯化铁(FeCl3·6H2O)为铁源,以十六烷基三甲基溴化铵(CTAB)为表面活性剂,采用水热法制备了准立方体氧化铁纳米材料.所得样品用XRD、SEM及SQUID-VSM等手段进行了表征.结果表明,所得氧化铁纳米材料为边长约700 nm的准立方体,其剩余磁感应强度为0.07 emu/g,矫顽力为1800 Oe,表现出一定的铁磁性.     

Au-Pd/TiO2-Al2O3催化剂的加氢脱硫性能研究

采用溶胶凝胶(sol-ge1)、共沉淀(CP)和沉积沉淀(DP)法制备了介孔TiO2-Al2O3复合载体(简称复合载体);以噻吩加氢脱硫(HDS)为探针反应,考察了复合载体制备条件对负载型Au-Pd催化剂噻吩HDS反应性能的影响;并采用X射线衍射进行表征.结果表明,不同温度焙烧的TiO2一Al2O3复合载体都具有介孔结构,其中773 K焙烧制得的TiO2一Al2O3复合载体的比表面积和孔容较大,B酸中心较多;以乙醇还原的Au-Pd/TiO2-Al2O3催化剂的加氢脱硫活性较好.乙醇还原的Au-Pd/TiO2-Al2O3催化剂中Au-Pd之间及活性组分与载体之间的相互作用较强,形成AuxPdy合金的晶粒较小,活性组分的分散度和活性表面积较大,反应活化能较低,这些均有利于催化剂活性的提高.     

Cu-Cr2O3催化剂上二氟乙酸甲酯催化加氢合成二氟乙醇

采用共沉淀法制备了Cu-Cr₂O₃催化剂,考察了铜含量对Cu-Cr₂O₃催化剂的二氟乙酸甲酯加氢合成二氟乙醇性能的影响。运用X射线衍射(XRD)、程序升温还原(TPR)、BET和Raman光谱技术对该催化剂进行了表征。结果表明,还原态Cu-Cr₂O₃催化剂物相主要由Cu和Cr₂O₃组成,然而30Cu-Cr₂O₃和50Cu-Cr₂O₃催化剂存在少量CuCr₂O₄和CuCrO₂复合氧化物。随着铜含量的增加,Cu-Cr₂O₃催化剂的二氟乙酸甲酯单程转化率呈现先上升后下降的趋势,而二氟乙醇选择性保持在70%左右; 30Cu-Cr₂O₃催化剂的二氟乙酸甲酯单程转化率达到最大值97%。Cu-Cr₂O₃催化剂的二氟乙酸甲酯加氢反应比速率随着铜含量的增加呈现增大的趋势,反应比速率的提高可能与催化剂中CuCr₂O₄和CuCrO₂物种的存在有关。     

纳米Fe3O4稳定的Pickering型ASA乳液

利用纳米Fe₃O₄作为稳定剂和乳化剂来制备Pickering型ASA（alkenyl succinic anhydride） 施胶乳液,并研究了固体颗粒浓度、油水比、水分散相pH对乳液类型、稳定性、形态及施胶性能的影响。结果表明,纳米Fe₃O₄能够乳化制备均一稳定的Pickering型ASA乳液。乳液在室温下静置稳定,析出油相体积分数随固体颗粒用量的增加而增大,随油水比的增大而减小。油水比为2：1,水分散相浓度为0.1%（质量分数）时制备的ASA乳液稳定性最佳。固体颗粒部分吸附在油/水界面处,部分分散在分散相中,随分散相中固体颗粒浓度的增加,乳液稳定性变差。乳液静置分层之前,ASA发生部分水解。在放置1 h后用于纸页浆内施胶,随ASA乳液用量的增加,纸页表面接触角逐渐增大,且纸页表面粗糙度下降。在ASA的添加量为1.0%（质量分数）时,纸页表面接触角达到93.5°,纸页表面粗糙度为15.924 μm。     

Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Accommodation of impurities in α-Al2O3, α-Cr2O3 and α-Fe2O3

Atomic scale computer simulation was used to predict the mechanisms and energies associated with the accommodation of aliovalent and isovalent dopants in three host oxides with the corundum structure. Here we consider a much more extensive range of dopant ions than has previously been the case. This enables a rigorous comparison of calculated mechanism energetics. From this we predict that divalent ions are charge compensated by oxygen vacancies and tetravalent ions by cation vacancies over the full range of dopant radii. When defect associations are included in the model these conclusions remain valid. At equilibrium, defects resulting from extrinsic dopant solution dominate intrinsic processes, except for the largest dopant cations. Solution reaction energies increase markedly with increasing dopant radius. The behaviour of cluster binding energies is more complex.     

The effect of foreign ions on the reactivity of the CaO-SiO2-Al2O3-Fe2O3 system: Part II: Cations

The subject of this paper is the effect of foreign cations on the reactivity of the CaO-SiO₂-Al₂O₃-Fe₂O₃ system. One reference mixture and eighteen modified mixtures, prepared by mixing the reference sample with 1% w/w of chemical grade MnO₂, CuO, V₂O₅, PbO, CdO, ZrO₂, Li₂O, MoO₃, Co₂O₃, NiO, WO₃, ZnO, Nb₂O₅, CrO₃, Ta₂O₅, TiO₂, BaO₂ and H₃BO₃ were studied. The effect on the reactivity is evaluated on the basis of the free lime content in samples sintered at 1200 and 1450 °C. At 1200 °C, the reactivity of the mixture is greatly increased in the presence of Cu and Li oxides. Based on their effect at 1450 °C, the added elements can be divided into three groups. W, Ta, Cu, Ti and Mo show the most positive effect, decreasing the free CaO (fCaO) content by 30-60%, compared with the pure sample. Cr and B cause an increase of fCaO content, while the rest of the elements exhibit a marginal positive effect. According to their volatility at 1450 °C, the added compounds can be subdivided into three groups of low (Ti⁴⁺, Cu²⁺, Mo⁶⁺, W⁺⁶, V⁵⁺, Zn²⁺, Zr⁴⁺), moderate (Cr⁶⁺, Co³⁺, Ni²⁺, Mn⁴⁺) and high volatility (Cd²⁺, Pb²⁺). All burned samples, analyzed by means of X-ray diffraction, have a final mineralogical composition, which corresponds to the structure of a typical clinker.     

Hydrodesulphurization performance of NiW/TiO2-Al2O3 catalyst for ultra clean diesel

TiO₂-Al₂O₃ binary oxide supports were obtained by sol–gel methods from Tetra-n-butyl-titanate and pseudoboehmite/aluminium chloride resources. The typical physico-chemical properties of NiW/TiO₂-Al₂O₃ catalysts with different TiO₂ loadings and their supports were characterized by means of BET, XRD and UV–vis DRS, etc. The BET results indicated that the specific surface areas of NiW/TiO₂-Al₂O₃ catalysts were as higher as that over pure γ-Al₂O₃ support, and the pore diameters were also large. The XRD and UV–vis DRS analyzing results showed that the Ti-containing supported catalysts existed as anatase TiO₂ species and the incorporation of TiO₂ could adjust the interaction between support and active metal, and impelled the higher reducibility of tungsten. The hydrodesulphurization (HDS) performance of the series catalysts were evaluated with diesel feedstock in a micro-reactor unit, and the HDS results showed that NiW/TiO₂-Al₂O₃ catalysts exhibited higher activities of ultra deep hydrodesulphurization of diesel oil than that of NiW/Al₂O₃ catalyst. The optimal TiO₂ content of NiW/TiO₂-Al₂O₃ catalysts was about 15 m%, and the corresponding HDS efficiency could reach to 100%. The sulphur contents of diesel products over NiW/TiO₂-Al₂O₃ (from pseudoboehmite/AlCl₃) catalysts with suitable TiO₂ content could be less than 15 ppmw, which met the sulphur regulation of Euro IV specification of ultra clean diesel fuel.     

新型CO2低温捕集与N2/O2分离复合系统性能分析

提出了一种CO₂低温捕集液化与N₂/O₂分离的新型复合系统,并且对该系统的性能以及优势进行了分析。这一系统不仅将CO₂低温捕集液化与N₂/O₂的分离结合起来,而且能达到降低能耗与减少投资的目的。采用理论分析和软件模拟相结合的方法,对该系统进行可行性分析。结果显示,这一新型系统不仅能量消耗低于传统醇胺吸收捕集CO₂的系统,该新型复合系统捕集1 t CO₂耗能3.29 GJ·t^-1,而传统MDEA吸收法耗能4.11 GJ·t^-1。而且在该系统中,CO₂分离液化的同时,可以获得副产物N₂与O₂。本研究阐明了一种CO₂低温捕集液化与N₂/O₂分离复合系统的新思想。     

TiO2-V2O5纳米纤维光催化氧化烟气中的Hg0

对静电纺丝法制备的TiO₂和TiO₂-V₂O₅纳米纤维进行光催化脱除模拟烟气中Hg⁰的研究。对纳米纤维进行了SEM、TEM、XRD、BET和UV-Vis检测。结果表明TiO₂-V₂O₅纳米纤维为锐钛矿,V₂O₅高度分散在TiO₂中。纤维直径在200 nm左右,由粒径为10 nm左右的微粒组成。掺杂V₂O₅后,纤维的吸光范围扩大,在可见光范围内的吸光度比纯TiO₂时有了很大提高。实验研究了不同光照条件、V₂O₅的掺杂量和循环次数对脱汞的影响,分析了TiO₂-V₂O₅催化脱汞的机理。当V₂O₅的质量含量为3%时,TiO₂-V₂O₅在可见光下的脱汞率可达到66%,比纯TiO₂时的7%有了显著提高;纤维的脱汞性能稳定,多次循环后紫外光和可见光下的脱汞率仍分别保持在80%和65%左右。电子的跃迁和电子、空穴的快速分离是TiO₂-V₂O₅在可见光下脱汞率提高的主要原因。     

木质素磺酸钠在TiO2/水界面的吸附特性

木质素磺酸钠在固体表面的吸附特性决定了其应用性能,利用红外和紫外分光光度仪,采用剩余质量分数法研究了温度、pH值、无机盐和氢键破坏剂脲对木质素磺酸钠在TiO₂/水界面吸附动力学和等温吸附性能的影响,初步探讨了其在固液界面的吸附作用机理。结果表明,该吸附为单层多点式吸附,随着温度升高和pH值减小,木质素磺酸钠在TiO₂/水界面的吸附速率常数和饱和吸附量均增大,而离子强度的增大和脲的加入却使吸附速率常数减小;木质素磺酸钠在TiO₂/水界面的吸附驱动力为静电、疏水和氢键作用,疏水作用力可显著增加其吸附量。