Effect of alloying and aging on morphological changes from lamellar to equiaxed microstructure of <Emphasis Type="Italic">α</Emphasis><Subscript>2</Subscript>+<Emphasis Type="Italic">γ</Emphasis> titanium aluminides

The stability of a lamellar structure consisting of α ₂ and γ phases in alloys Ti-48Al, Ti-48Al-2Mo, Ti-48Al-4Nb, and Ti-48Al-1Mo-4Nb has been studied as a function of aging time and temperature. The alloys were solution treated (1400 °C, 30 min, and air-cooled (AC)) and aged at 1000 °C and 1100 °C for 1, 4, and 16 hours, respectively. The results indicate that the kinetics of lamellae to equiaxed transformation depends on alloy chemistry, aging time, and temperature. The Nb decreases and Mo increases the kinetics of transformation. The combined effect of Nb and Mo results in the highest volume fraction of equiaxed microstructure at a given aging time and temperature. The results have been discussed in relation to microstructural features and have been compared with those reported in other α ₂+γ alloys.     

Structural Analysis,Electrochemical Behavior,and Biocompatibility of Novel Quaternary Titanium Alloy with near β Structure

This article analyses the microstructure, electrochemical behavior, and biocompatibility of a novel Ti-20Nb-10Zr-5Ta alloy with low Young’s modulus (59 GPa) much closer to that of bone, between 10 and 30 GPa, than Ti and other Ti alloys used as implant biomaterial. XRD and SEM measurements revealed a near β crystalline microstructure containing β phase matrix and secondary α phase, with a typical grain size of around 200 μm. The corrosion behavior in neutral Ringer solution evidenced: self-passivation behavior characterizing a very resistant passive film; an easy passivation as a result of favorable influence of the alloying elements Nb, Zr, and Ta that participate with their passive oxides to the formation of the alloy passive film; low corrosion and ion release rates corresponding with very low toxicity. In MEM solution, the novel alloy demonstrated very high corrosion resistance and no susceptibility to localized corrosion. Biocompatibility was evaluated on in vitro human osteoblast-like and human immortalized pulmonary fibroblast cell (Wi-38) lines and the new Ti-20Nb-10Zr-5Ta alloy exhibited no cytotoxicity. The new Ti-20Nb-10Zr5Ta alloy is a promising material for implants due to combined properties of low elastic modulus, very low corrosion rate, and good biocompatibility.     

Water Network in Room-Temperature Ionic Liquid: <Emphasis Type="Italic">N,N</Emphasis>-Diethyl-<Emphasis Type="Italic">N</Emphasis>-Methyl-<Emphasis Type="Italic">N</Emphasis>-2-Methoxyethyl Ammonium Tetrafluoroborate

Crystal structures of room-temperature ionic liquid (RTIL)-H₂O mixtures are determined by the X-ray diffraction method. The RTIL is N,N-diethyl-N-methyl-N-2-methoxyethyl ammonium tetrafluoroborate, [DEME][BF₄]. At 0.9 mol pct H₂O, two kinds of superstructures occur simultaneously without a strain. Also, the volume of the unit cell is very small only at 0.9 mol pct additives. This relates to the composite domain structure, including a twin-related one, as an elastic anomaly. At other water concentrations, such an extraordinary behavior is not observable. By assuming a sublattice having an equivalent lattice constant, a water network at 1 mol pct H₂O is simulated using a Monte Carlo (MC) method. The network develops over the medium range in the simulation box.     

Studies on Synthesis and Characterization of Mo Based <Emphasis Type="Italic">In Situ</Emphasis> Composite by Silicothermy Co-reduction Process

The results of an in situ synthesis of refractory metal–intermetallic composite (RMIC), Mo-16Cr-4Si (wt pct) multiphase alloy and its characterization, are presented in this study. The alloy was prepared from the oxides of molybdenum and chromium by their co-reduction with Si metal powder as a reductant. The exothermic nature of these reactions resulted in the formation of consolidated composite as a product in a single step. The thermodynamic aspects of exothermic reactions were studied by thermogravimetry/differential thermal analyzer. As-reduced alloys were remelted by arc melting and heat treated to obtain a homogenous microstructure. The evolution of phases and microstructures qA studied by X-ray diffraction, scanning electron microscopy, and energy-dispersive spectrum analysis. The multiphase alloy consisted of Mo₃Si and discontinuous (Mo, Cr) (ss) phase with a volume percentage of 28 pct. The synthesized alloys were characterized with respect to composition, phases, microstructure, hardness, and oxidation behavior.     

高Ta钛合金在沸腾硝酸中的腐蚀行为

对高Ta含量钛合金Ti-32Ta在8 mol/L沸腾硝酸溶液中进行了全浸腐蚀实验,研究了Ti-32Ta合金在沸腾硝酸中的腐蚀行为。采用扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线衍射光电子能谱(XPS)等分析方法对钛合金腐蚀表面的钝化膜进行了成分、组织结构及合金价态分析。结果表明:Ti-32Ta合金在沸腾硝酸溶液中呈现均匀腐蚀行为,在介质中通入一定流量的新鲜空气对合金稳定腐蚀阶段的腐蚀速率影响不大。与Ti-6Ta合金相比,Ti-32Ta合金腐蚀后形成的钝化膜更薄更致密,耐蚀性能更好。两种合金腐蚀钝化膜中Ti和Ta的价态组成相同,Ti-32Ta合金腐蚀表面Ta及Ta2O5的含量高于Ti-6Ta合金腐蚀表面。     

Effect of Phase Contiguity and Morphology on the Evolution of Deformation Texture in Two-Phase Alloys

Deformation texture evolution in two-phase xFe-yNi-(100-x-y)Cr model alloys and Ti-13Nb-13Zr alloy was studied during rolling to develop an understanding of micro-mechanisms of deformation in industrially relevant two-phase FCC-BCC steels and HCP-BCC titanium alloys, respectively. It was found that volume fraction and contiguity of phases lead to systematic changes in texture, while morphology affects the strength of texture. There was a characteristic change in texture from typical Brass-type to a weaker Copper-type texture in the austenite phase accompanied with a change from alpha fiber to gamma fiber in ferrite phase for Fe-Ni-Cr alloys with increase in fraction of harder ferrite phase. However, similar characteristic texture evolution was noted in both α and β phase irrespective of the different initial morphologies in Ti-13Nb-13Zr alloy. Viscoplastic self-consistent simulations with two-phase scheme were able to qualitatively predict texture evolution in individual phases. It is proposed that the transition from iso-strain-type behavior for equiaxed microstructure at low strain to iso-stress-type behavior at higher strain is aided by the presence of higher volume fraction of the second phase and increasing aspect ratio of individual phases in two-phase alloys.

     

Precipitation in Nb-Stabilized Ferritic Stainless Steel Investigated with <Emphasis Type="Italic">in-situ</Emphasis> and <Emphasis Type="Italic">ex-situ</Emphasis> Transmission Electron Microscopy

A Nb-stabilized Fe-15Cr-0.45Nb-0.010C-0.015N ferritic stainless steel is studied with transmission electron microscopy (TEM) to investigate the morphology and kinetics of precipitation. Nb_x(C,N)_y\hbox{Nb}_{x}\hbox{(C,N)}_y and MnS precipitates are present in the steel in the initial condition. Ex-situ TEM analysis is performed on samples heat treated at 973 K, 1073 K, 1173 K, and 1273 K (700 °C, 800 °C, 900 °C, and 1000 °C). Within this temperature range, both Fe₂Nb\hbox{Fe}_2\hbox{Nb} and Fe₃Nb₃X_x\hbox{Fe}_{3}\hbox{Nb}_{3}\hbox{X}_{x} (with X = C or N) precipitates form. Fe₂\hbox{Fe}_2Nb is observed at 1073 K (800 °C).   Fe₃Nb₃X_x\;\hbox{Fe}_{3}\hbox{Nb}_{3}\hbox{X}_{x} precipitates form at the grain boundaries between 973 K and 1273 K (700 °C and 1000 °C). Up to at least 1173 K (900 °C) their fraction increases with time and temperature, but at 1273 K (1000 °C) they lose stability with respect to Nb_x(C,N)_y.\hbox{Nb}_{x}\hbox{(C,N)}_{y}. With in-situ TEM, no phase transition is observed between room temperature and 1243 K (970 °C). At 1243 K (970 °C) the precipitation of Fe₃Nb₃X_x\hbox{Fe}_{3}\hbox{Nb}_{3}\hbox{X}_{x} is observed in the neighborhood of a dissolving Nb₂\hbox{Nb}_2(C,N) precipitate. For sections of grain boundaries where no Nb_x(C,N)_y\hbox{Nb}_x\hbox{(C,N)}_y precipitates are present, Fe₃Nb₃X_x\hbox{Fe}_3\hbox{Nb}_3\hbox{X}_{x} does not form. It is concluded that the precipitation of Fe₃Nb₃X_x\hbox{Fe}_{3}\hbox{Nb}_{3}\hbox{X}_x is directly related to the dissolution of Nb₂\hbox{Nb}_2(C,N) through the redistribution of C or N.     

<Emphasis Type="Italic">In-Situ</Emphasis> Electrochemical Investigations of a Nickel-Based Alloy Subjected to Fatigue

The HASTELLOY C2000 superalloy is a commercially designed superalloy manufactured to function in reducing and oxidizing corrosive solutions. The industrial applications have tremendous potential in automotive, structural, aviation, and storage components. Although C2000 demonstrates good reducing and oxidizing traits in extremely aggressive media (which are attractive features of its chemistry), changes in the mechanical properties are believed to be insignificant due to its strong propensity to passivate under corrosive conditions. The ductility behavior and corrosion properties of C2000 are superior to those of stainless steels. The objective of the present study is to examine the corrosion-fatigue behavior of C2000 in a 3.5 wt pct sodium-chloride (NaCl) solution. C2000 submerged in 3.5 wt pct NaCl at room temperature is not susceptible to localized corrosion, such as pitting, during fatigue. At an accelerated potential of 350 mV, the current responses show an increase in the current due to slip steps emerging to the surface as a result of fatigue. The crack-initiation site and the examination of the fracture morphology are discussed. This article is based on a presentation given in the symposium entitled “Deformation and Fracture from Nano to Macro: A Symposium Honoring W.W. Gerberich’s 70th Birthday,” which occurred during the TMS Annual Meeting, March 12–16, 2006 in San Antonio, Texas and was sponsored by the Mechanical Behavior of Materials and Nanomechanical Behavior Committees of TMS.

---

Effect of V or Zr addition on the mechanical properties of the mechanically alloyed Al-8wt.% Ti alloys

The thermal stability of the MA Al-Ti alloy was improved by the addition V or Zr. Such improvement is attributed to the retarded coarsening of the dispersoid phases due to the improved coherency between dispersoid phases and the Al-matrix in the presence of alloying elements V and Zr.The compressive yield strength of ternary MA Al-8Ti-2.8V and Al-8Ti-5.1Zr alloys were superior to binary MA Al-STi alloy at the temperature of above 400 °C, but the MA Al-8Ti-5.1Zr alloy showed some brittleness at 450 °C.     

In vivo study of stainless steel and Ti-13Nb-13Zr bone plates in a sheep model

A sheep study was performed to compare the in vivo performance of bone plates of 316L stainless steel and a new titanium alloy, titanium + 13% niobium + 13% zirconium (Ti-13Nb-13Zr), which had been subjected to a diffusion hardening treatment to produce a blue, wear resistant surface. Bone plates and screws of stainless steel and diffusion hardened Ti-13Nb-13Zr were implanted in adult sheep, in one group (with unosteotomized femurs) for 16 weeks, and in the other (with osteotomized femurs) for 8 weeks. At harvest, the diffusion hardened Ti-13Nb-13Zr devices had superior fixation strength, with greater screw torque out strength and fewer loose screws. In the osteotomized animals, the femurs with diffusion hardened Ti-13Nb-13Zr plates had higher torsional strength after removal of the implants; however, the difference was not statistically significant. In the unosteotomized animals, the torsional strength of the femurs was identical for both materials. There was a slightly reduced incidence of infection (bacterial adhesion) for the sheep with diffusion hardened Ti-13Nb-13Zr implants. In a parallel in vitro study, the magnetic resonance imaging compatibility of Ti-13Nb-13Zr was significantly superior to that of stainless steel. This indicates that diffusion hardened Ti-13Nb-13Zr may be an attractive alternative material for osteosynthesis.     

Functionally Graded Al Alloy Matrix <Emphasis Type="Italic">In-Situ</Emphasis> Composites

In the present work, functionally graded (FG) aluminum alloy matrix in-situ composites (FG-AMCs) with TiB₂ and TiC reinforcements were synthesized using the horizontal centrifugal casting process. A commercial Al-Si alloy (A356) and an Al-Cu alloy were used as matrices in the present study. The material parameters (such as matrix and reinforcement type) and process parameters (such as mold temperature, mold speed, and melt stirring) were found to influence the gradient in the FG-AMCs. Detailed microstructural analysis of the composites in different processing conditions revealed that the gradients in the reinforcement modify the microstructure and hardness of the Al alloy. The segregated in-situ formed TiB₂ and TiC particles change the morphology of Si particles during the solidification of Al-Si alloy. A maximum of 20 vol pct of reinforcement at the surface was achieved by this process in the Al-4Cu-TiB₂ system. The stirring of the melt before pouring causes the reinforcement particles to segregate at the periphery of the casting, while in the absence of such stirring, the particles are segregated at the interior of the casting.     

The role of phase transformation in electron-beam welding of TiAl-based alloys

The weldability of two TiAl-based alloys, Ti-45Al-2Nb-2Mn and Ti-48Al-2Nb-2Mn, was investigated with the electron-beam welding process. It was found that the alloys were susceptible to solid-state cracking due to high thermally induced stresses and, more significantly, to the intrinsic brittleness of the microstructures. This work correlated the quality of the TiAl welds, made using different sets of welding parameters which gave rise to different cooling rates, to the microstructures that developed during welding. It was found that the welds were crack-free if the weld cooling rates were such that decomposition of the high-temperature α phase in the weld was not suppressed. It was shown that the Ti-48Al-based alloy was less susceptible to the solid-state cracking and, thus, was more weldable than the Ti-45Al-based alloy because the α phase in the alloy with a higher aluminum content could decompose more readily. A continuous cooling transformation (CCT) diagram is suggested to be used as an appropriate reference for the selection of welding parameters which induce suitable microstructures in the welds and result in crack-free welds.     

Rare-earth metals (REMs) in nickel aluminide-based alloys: I. Physicochemical laws of interaction in the Ni-Al-REM and Ni<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Al<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>-REM-AE (alloying element) systems

The data on the Ni-Al-R (R = REM Sc, Y, La, lanthanides) binary and ternary systems and the interactions of three rare-earth metals (yttrium, lanthanum, cerium) with the main alloying elements (Ti (Zr, Hf), Cr (Mo, W) that are introduced into Ni₃Al-based VKNA alloys are analyzed. The binary aluminides of REMs in the Ni-Al-R ternary systems are shown to be in equilibrium with neither NiAl nor Ni₃Al. The solid solution of aluminum in RNi₅, which penetrates deep into these ternary systems, is the most stable phase in equilibrium with Ni₃Al. In the NiAl (Ni₃Al)-AE-R systems, REM precipitation (segregation) on various defects and interfaces in nickel aluminides is likely to be the most probable, and REMs are thought to interact with the most active impurities in real alloys (C, O, N), since REMs have a large atomic radius and, thus, are virtually undissolved in nickel, aluminum, and nickel aluminides.     

<Emphasis Type="Italic">In Situ</Emphasis> Micromechanical Testing for Single Crystal Property Characterization

An in situ method to fully characterize the single crystal properties for polycrystalline alloys is developed using microscale experimental and analysis techniques. The developed method can be applied to metallic engineering alloys that do not exist in single crystal form. Thus using this technique, testing and analysis on polycrystalline samples can yield the single crystal elastic and plastic properties required as input to micro- and mesoscale computational models such as those which rely on crystal plasticity theory. Compression and shear experiments are conducted on single crystal specimens of various crystallographic orientations. Analytical and numerical analysis of the experimental results yields a set of equations that can be solved for the single crystal elastic parameters. This novel methodology is demonstrated to produce reasonable elastic property prediction results for an aerospace aluminum lithium alloy, AA2070. Details regarding the experiments and analysis are provided to facilitate application of the technique to a wide range of polycrystalline material systems and properties.     

Effects of oxygen and heat treatment on the mechanical properties of alpha and beta titanium alloys

Two alloys, Ti-6Al-2V and Ti-2Al-16V, simulating the alpha and beta phases of Ti-6A1-4V, respectively, were prepared with oxygen concentrations from 0.07 to 0.65 wt pct (0.20 to 1.83 at. pct). Their microstructure, deformation behavior, and strength were investigated with X-ray diffraction, microscopy, and mechanical tests to determine the effects of oxygen concentration and heat treatment. In both alloys the hardness increases in identical fashion with the square root of oxygen concentration. The alloys' strengths also depend on heat treatment, but in different ways. Whereas the alpha alloy is non-age-hardenable, the beta alloy's strength can be doubled by aging. The hardening effect of oxygen is generally unaffected by heat treatment, except for the alloys with the highest oxygen concentrations. During aging of the alpha a small amount of Ti₃Al can form, and slight age-hardening occurs. The ductility of the alpha alloy is little affected by aging. On the other hand, oxygen causes a change from good ductility at low oxygen concentration (0.07 wt pct) to total brittleness at 0.65 wt pct oxygen, independent of heat treatment. In the beta alloy there are complex phase transformations depending on heat treatment. Its deformation behavior varies from very ductile in solutiontreated and quenched (STQ) condition to totally brittle in aged conditions. The aging embrittlement appears to be caused by alpha and some omega precipitation. Decoration of the beta grain boundaries with precipitates accounts for the intergranular brittle fracture. Oxygen, on the other hand, is not an embrittler, although it reduces the ductility of the beta alloy.     

Corrosion Behavior of Friction Stir-Processed and Gas Tungsten Arc-Welded Ti-6Al-4V

The corrosion behavior of the investment-cast Ti-6Al-4V alloy in 5-pct HCl solution was investigated after gas tungsten arc welding and friction stir (FS) processing. The FS-processed samples exhibited superior corrosion behavior compared with the base metal and the arc-welded samples. The inferior corrosion resistance of the arc weldment was attributed to the acicular α and β microstructure and the alloying element partitioning between the phases. This was confirmed by scanning electron microscopy evaluations of the surface of specimens that had been immersed 50 hours in 20-pct HCl at 308 K (35 °C). In addition, the results indicated that vanadium as an alloying element has a detrimental effect on the corrosion performance of Ti-6Al-4V alloy in an HCl solution.     

Microstructure characterization of Al<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>CoCrCuFeNi high-entropy alloy system with multiprincipal elements

A new approach for the design of alloy systems with multiprincipal elements is presented in this research. The Al _x CoCrCuFeNi alloys with different aluminum contents (i.e., x values in molar ratio, x=0 to 3.0) were synthesized using a well-developed arc-melting and casting method. These alloys possessed simple fcc/bcc structures, and their phase diagram was predicted by microstructure characterization and differential thermal analyses. With little aluminum addition, the alloys were composed of a simple fcc solid-solution structure. As the aluminum content reached x=0.8, a bcc structure appeared and constructed with mixed fcc and bcc eutectic phases. Spinodal decomposition occurred further on when the aluminum contents were higher than x=1.0, leading to the formation of modulated plate structures. A single ordered bcc structure was obtained for aluminum contents larger than x=2.8. The effects of high mixing entropy and sluggish cooperative diffusion enhance the formation of simple solid-solution phases and submicronic structures with nanoprecipitates in the alloys with multiprincipal elements rather than intermetallic compounds.     

不同熔炼条件下B、C元素对Ti-47Al-2Cr-2Nb合金铸态组织的影响

研究了不同熔炼条件下B、C元素对Ti-47Al-2Cr-2Nb合金的铸态组织的影响。研究结果表明：B、C元素的添加显著地细化了Tim基合金的组织片层,C元素的细化效果优于B元素。在所研究的精炼时间内,无论添加微量元素B还是C元素,精炼时间为30min时获得的铸锭组织中片层最细。