宽频压电振动能量采集器的力-电输出特性分析

压电振动能量采集器是一种新型的力(加速度)-电耦合转换输出器件,为了提高单自由度悬臂梁压电振动能量采集器的输出功率和工作频带,通过在单自由度悬臂梁压电振动能量采集器模型基础上增加一个弹性放大器的方法,构造形成了具有两自由度的宽频压电振动能量采集器。利用ANSYS有限元软件建立了宽频压电能量采集器的有限元力-电耦合模型,数值分析了模型中各参数(如质量比、阻尼比以及负载电阻等)对系统力特性(速度、加速度等)和电输出特性(电压、电流、输出功率等)的影响。研究结果表明：大的质量比和小的阻尼比能够提高压电悬臂梁能量采集器的输出功率并拓展其工作频带;短路谐振状态下的匹配电阻能够使能量采集器产生较大的输出电流,而开路谐振状态的匹配电阻能够使能量采集器产生较大的输出电压,优化后的短路谐振和开路谐振最大输出功率分别达到4386.5 mW/g2和4263.4 mW/g2。频带宽度达到10 Hz,且是SDOF系统的5倍。     

基于双ZnO薄膜单元并联结构的微型压电振动能量采集器(英文)

报道了一种基于ZnO压电薄膜双单元结构的压电式微型振动能量采集器,其中的双压电元件是并联结构.采用射频磁控溅射技术制备ZnO压电薄膜,同时,该压电式振动能量采集器采用微加工技术制作.测试表明该器件的共振频率为1 300 Hz,基于ZnO薄膜双单元并联结构的压电式振动能量采集器比起具有同样尺寸的传统型压电振动能量采集器有更高的输出性能.在频率为1 300 Hz,加速度为10 m/s2的外界振动激励下,该压电式振动能量采集器在1 MΩ负载电阻上产生的电压为2.06 V;当负载电阻为0.6 MΩ时,输出功率最大为1.25μW.     

磁力非线性耦合的I-L组合压电梁俘能器发电性能试验研究EI北大核心CSCD

针对线性的压电振动俘能器俘能频带过窄,输出较低等问题,提出了一种磁力非线性耦合的I-L组合压电梁俘能器。俘能器由带永磁铁的I型压电梁和L型压电梁组成,可通过调节两永磁铁间的水平距离,得到不同的非线性磁力耦合效应。试验结果表明:存在最优电阻使压电俘能系统的输出功率最大;对比无磁力系统,磁力耦合的I-L组合压电梁俘能器共振频率发生了明显的偏移:I型压电梁向左偏移,L型压电梁向右偏移,拓宽了系统的俘能频带;当激励加速度为0.2 g水平距离为20 mm、激振频率为18.4 Hz时,俘能器最大可得到1.2 mW的输出功率。     

Bimorph piezoelectric vibration energy harvester with flexible 3D meshed-core structure for low frequency vibration

This paper proposes a bimorph piezoelectric vibration energy harvester (PVEH) with a flexible 3D meshed-core elastic layer for improving the output power while lowering the resonance frequency. Owing to the high void ratio of the 3D meshed-core structure, the bending stiffness of the cantilever can be lowered. Thus, the deflection of the harvester and the strain in the piezoelectric layer increase. According to vibration tests, the resonance frequency is 15.8% lower and the output power is 68% higher than in the conventional solid-core PVEH. Compared to the solid-core PVEH, the proposed meshed-core PVEH (10 mm × 20 mm × 280 μm) has 1.3 times larger tip deflection and the maximum output power is 24.6 μW under resonance condition at 18.7 Hz and 0.2G acceleration. Hence it can be used as a power supply for low-power-consumption sensor nodes in wireless sensor networks.     

Vibration energy harvester with sustainable power based on a single-crystal piezoelectric cantilever array

We designed and fabricated a bimorph cantilever array for sustainable power with an integrated Cu proof mass to obtain additional power and current. We fabricated a cantilever system using single-crystal piezoelectric material and compared the calculations for single and arrayed cantilevers to those obtained experimentally. The vibration energy harvester had resonant frequencies of 60.4 and 63.2 Hz for short and open circuits, respectively. The damping ratio and quality factor of the cantilever device were 0.012 and 41.66, respectively. The resonant frequency at maximum average power was 60.8 Hz. The current and highest average power of the harvester array were found to be 0.728 mA and 1.61 mW, respectively. The sustainable maximum power was obtained after slightly shifting the short-circuit frequency. In order to improve the current and power using an array of cantilevers, we also performed energy conversion experiments.     

Dielectric and piezoelectric properties of CeO2-added nonstoichiometric (Na0.5K0.5)0.97(Nb0.96Sb0.04)O3 ceramics for piezoelectric energy harvesting device applications

In this study, nonstoichiometric (Na(0.5)K(0.5))(0.97)(Nb(0.96)Sb(0.04))O(3) ceramics were fabricated and their dielectric and piezoelectric properties were investigated according to the CeO(2) addition. In this ceramic composition, CeO(2) addition improved sinterability, electromechanical coupling factor k(p), mechanical quality factor Q(m), piezoelectric constant d(33), and g(33). At the sintering temperature of 1100°C, for the 0.2wt% CeO(2) added specimen, the optimum values of density = 4.359 g/cm(3), k(p) = 0.443, Q(m) = 588, ε(r) = 444, d(33) = 159 pC/N, and g(33) = 35 × 10(-3) V·m/N, were obtained. A piezoelectric energy harvesting device using 0.2 wt% CeO(2)- added lead-free (K(0.5)Na(0.5))(0.97)(Nb(0.96)Sb(0.04))O(3) ceramics and a rectifying circuit for energy harvesting were fabricated and their electrical characteristics were investigated. Under an external vibration acceleration of 0.7 g, when the mass, the frequency of vibration generator, and matching load resistance were 2.4 g, 70 Hz, and 721 Ω, respectively, output voltage and power of piezoelectric harvesting device indicated the optimum values of 24.6 mV(rms) and 0.839 μW, respectively-suitable for application as the electric power source of a ubiquitous sensor network (USN) sensor node.     

新型聚四氟乙烯体材料双面驻极结构振动能量收集器

提出一种新型静电式振动能量收集器，该器件采用基于聚四氟乙烯体材料驻极体的双面电晕驻极结构，提高了薄膜驻极体静电式振动能量收集器的输出功率．在电晕驻极栅网电压为-700V的条件下，体材料驻极体的上下表面分别获得了-564．0V±83．1V、-636．4V±69．7V的表面电位均值．采用组装方式制成器件，并在正弦激振条件下测试器件的输出性能．实验结果表明，在振动频率10Hz、峰值加速度1．2g的条件下，器件输出峰值功率达到30μw，平均功率达到5．5μw，优于目前多数薄膜驻极体器件的性能，接近低功耗传感器的实际功率要求．     

A multisource energy harvesting utilizing highly efficient ferroelectric PMN-PT single crystal

This paper demonstrates a multi-source energy harvester that is able to utilize simultaneously both piezoelectric and pyroelectric effects in lead magnesium niobate-lead titanate (PMN-PT) single crystal. The paper presents a study of PMN-PT single crystal with a (67:33) composition grown in our laboratory via a vertical gradient freeze method without any flux. The performance of the piezoelectric and pyroelectric energy harvester using unimorph device structure was evaluated via modeling and experiment. The theoretical study was implemented based on a distributed parameter electromechanical model and the modelling procedure was approximated using finite element analysis to predict the electromechanical behavior of the harvester. The maximum power density at a resonance frequency of 50 Hz and optimum resistance of 2 MΩ was 16.7 nW/(g² cm³) under a 1 g acceleration of vibration. The measured values of electrical output parameters were in good agreement with theoretical and modelling results using MATLAB and COMSOL Multiphysics, respectively. By using the pyroelectric effect along with the piezoelectric effect, the output voltage of the energy harvester was found to be enhanced at the optimum resistance and specific frequency values. It was noticed that the output voltage was increased monotonically with temperature-difference (ΔT) and reaches up to 180 % of its original value under temperature difference of 1.7 °C at a frequency value of 49 Hz.     

Z型梁结构压电式能量采集性能分析

振动能量采集能够将外部环境中的振动能转化为电能,具有绿色可持续、节能环保、设计灵活等优势,在工业、生物、医学、军事等领域具有广阔的应用前景.为使振动型能量采集器适应更为复杂多变的工作环境,提高其采集功率和工作频带,提出一种多梁结构-Z型梁结构压电式能量采集器.理论分析了该采集器的固有振动特性,并通过有限元分析了结构尺寸...     

多方向压电振动能量收集装置及其优化设计

摘要：为实现对不同方向环境振动能量的收集,提出了一种新颖的多方向振动能量收集装置的设计结构,装置的换能部分采用了一种Rainbow型压电结构。为提高多方向振动能量收集装置收集能量的效果,以多方向振动能量收集装置输出的总电能为目标函数,综合考虑金属弹性基片的强度、装置振动的固有频率及装置的尺寸空间要求等多种因素,采用序列二次规划法对能量收集装置的结构参数进行了优化。该多方向振动能量收集装置经过优化后,在Y向激励时,其输出的总电能为37.146μJ,比优化前提高了30.82%,当沿装置体对角线方向激励时,结构装置输出的总电能为58.715μJ,比优化前提高了29.24%,装置的能量收集效果得到了明显提高。分析结果为多方向振动能量收集装置的设计、制造及应用提供了技术依据。     

基于MEMS技术的三明治型电磁式微振动能量采集器

本文中设计了一种结构新颖的三明治型电磁式微振动能量采集器,主要包括上线圈、下线圈和由永磁体与硅基平面镍弹簧构成的拾振系统.上、下线圈的对称性分布有利于充分利用永磁体周围的磁场从而提高整个器件的机械能-电能转换效率.实验样机主要采用MEMS微加工技术制作,其中的硅基平面镍弹簧采用体硅微加工和微电镀技术制作,双层铜线圈采用微电镀和聚酰亚胺绝缘层技术制作.实验样机的体积约为0.32 cm3.振动特性测试表明,在外界加速度小于8 m/s2时,永磁体振幅随着加速度的增加而增加,在加速度大于8 m/s2以后,振幅几乎不再增加,出现饱和现象.电学特性测试表明,在8 m/s2加速度作用下,单线圈和串联线圈产生的感应电压峰峰值分别为82.5 mV和125 mV,因此,三明治结构的新型设计使得输出电压增加了51.5%.另外,在加速度为8 m/s2、频率为280.9 Hz的外界振动激励下,实验样机产生的最大负载电压和最大负载功率分别为125 mV和13.2μW.     

Design and fabrication of a PZT cantilever for low frequency vibration energy harvesting

In this study, a PZT cantilever with a Si proof mass is designed and fabricated for a low frequency energy harvesting application. A mathematical model of a multi-layer composite beam was derived and applied in a parametric analysis of the piezoelectric cantilever. Finally, the dimensions of the cantilever were determined for the resonant frequency of the cantilever. Our cantilever design was based on MATLAB and ANSYS simulations. For this simulation, the proof mass volumes were varied from 0 to 0.5 mm3 and resonant frequencies were calculated from 833.5 Hz to 125.5 Hz, respectively. Based on simulation, we fabricated a device with beam dimensions of about 4.10 mm x 0.48 mm x 0.012 mm, and an integrated Si proof mass with dimensions of about 0.481 mm x 0.48 mm x 0.45 mm. The resonant frequency, maximum peak voltage, and highest average power of the cantilever device were 224.8 Hz, 4.8 mV, and 2.24 nW, respectively.     

基于宽频-多模态的复合俘能器的解析模型与实验研究

为提高单频压电振动俘能器的能量转换效率和工作频带,结合压电和电磁能量转换机制,提出了一种新的混合俘能器系统。该系统由PZT悬臂梁、弹性悬挂磁铁块、粘附于悬臂梁末端磁铁块及谐振器等组成,引入谐振器及磁铁可实现增加系统模态数量和非线性。基于此混合振动俘能器建立了改进型连续体机电耦合解析模型,并由龙格-库塔算法进行了求解。在此基础上,研制了振动俘能器原理样机,并搭建了实验系统,通过实验和解析评估方法完成了单一式和复合式俘能器性能比对和评估;研究表明,所研究的混合型振动俘能器相对常规振动能量俘集原理可实现较宽的频率范围及多模态振动能量俘集,且能量俘集效率明显提高,具有较好的应用前景。     

Design and fabrication of a piezoelectric transducer for wind-power generator

This study investigates the feasibility of a high-performance ZnO piezoelectric transducer for wind-power generation applications. The piezoelectric transducer is constructed of a Cu/ZnO/ITO/PET structure. Closely examining the ITO/PET substrate by a nano indenter reveals a low Young's modulus of 6.62 Gpa for specific deflections. The ZnO piezoelectric film of 965 nm is deposited on ITO/PET substrate using a RF magnetron sputtering system at room temperature. A copper layer is attached to the ZnO/ITO/PET structure to construct piezoelectric transducers. Both scanning electron microscopy and X-ray diffraction indicate that, among the favorable characteristic of the ZnO piezoelectric film include a rigid surface structure and a high c-axis preferred orientation. According to cantilever vibration theory, a transducer with a cantilever length of 9.9 mm and vibration area of 1.5 cm² is designed for natural wind. An appropriate mass loading of 0.57 g on the cantilever is critical for increasing the vibration amplitude and promoting the generated power of a piezoelectric transducer. Finally, an open circuit voltage of 1.87 V for the ZnO piezoelectric transducer at a vibration frequency of 100 Hz is obtained by an oscilloscope. After rectifying and filtering, the output power of the generator exhibits an available benefit of 0.07 μW/cm² with the load resistance of 5 MΩ.     

RF Energy Transmission for a Low-Power Wireless Impedance Sensor Node

The proper management of energy resources is essential for any wireless sensing system. With applications that span industrial, civil, and aerospace infrastructure, it is necessary for sensors and sensor nodes to be physically robust and power efficient. In many applications, a sensor network must operate in locations that are difficult to access, and often these systems have a desired operational lifespan which exceeds that of conventional battery technologies. In the present study, the use of microwave energy is examined as an alternate method for powering compact, deployable wireless sensor nodes. A prototype microstrip patch antenna has been designed to operate in the 2.4 GHz ISM band and is used to collect directed radio frequency (RF) energy to power a wireless impedance device that provides active sensing capabilities for structural health monitoring applications. The system has been demonstrated in the laboratory, and was deployed in field experiments on the Alamosa Canyon Bridge in New Mexico in August 2007. The transmitted power was limited to 1 W in field tests, and was able to charge the sensor node to 3.6 V in 27 s. This power level was sufficient to measure two piezoelectric sensors and transmit data back to a base station on the bridge.      

基于谐振器的多模态压电换能结构研究

传统压电悬臂梁俘能器一般通过其基频与环境中某一激振频率的匹配来收集这个频率上的振动能,为俘获环境中多个激振频率上的能量,提出一种在压电悬臂梁上附加谐振器的多模态换能结构,由该结构组成的俘能器的前两阶共振频率可以被设计在给定的激振频率上,从而有效地收集分布在这两个频率上的能量.实验表明附加谐振器有效地提高了俘能效率,其中一阶模态的俘能效率相对附加等量质量块时提高了71％,二阶模态的俘能效率与原压电悬臂梁的一阶模态相当.     

悬臂梁压电振动能采集器的集总参数模型和实验验证

压电振动能采集器是无线传感节点的一种理想电源,近年来受到广泛关注．考虑质量块和逆压电效应影响,建立了在基础激励作用下的悬臂梁压电振动能采集器的集总参数运动微分方程,得到了采集器固有频率的解析表达式．引入了2个反映压电层连接方式的常数,建立了对单压电层、双压电层并联和双压电层串联的悬臂梁压电振动能采集器均适用的耦合电路方程．求解以上方程,得到了简谐基础激励下的输出电压表达式．实验结果表明,固有频率和输出电压表达式的相对误差分别小于10％和20％．     

Nano piezoelectric/piezomagnetic energy harvester with surface effect based on thickness shear mode

BackgroundEnergy harvesters with piezoelectric materials are widely discussed for the new kinds of smart structures. However, reports on the energy harvesters at the nano scale which have large potential applications in the future are rather limited.MethodsIt’s well known that the surface or interface stress can affect the mechanical properties of nanostructures. This work proposes the nano energy harvester with piezoelectric/piezomagnetic structure, in which the thickness-shear mode is considered by the surface stress model.ResultsThe vibration motion and output power density are derived and calculated. The peak value of the power density can be enlarged by increasing the residual surface stress and the surface effect on the nano-plate energy harvester can be influenced by both the surface piezoelectric and piezomagnetic elastic constants. Moreover, the harvesting ability can be improved by increasing the thickness of the piezoelectric layer.ConclusionThe capability of the energy harvester depends on the residual surface stress and the surface material constants. The proposed model provides the possibility of applying nano composite structures to the energy harvester.     

碰撞式微型压电风能采集器实验研究(英文)

为提高基于风致振动机理的微型风能采集器在低风速下的输出功率,设计了一种新型的碰撞式微型压电风能采集器.采集器主要由圆柱形钝体、铰接分隔板、压电悬臂梁和支架组成.通过铰接分隔板和压电悬臂梁的碰撞有效降低了采集器的工作风速.加工制作了采集器的原理样机并在小型风洞内进行了实验测量.通过实验发现分隔板与压电片横向间距对采集器的工作风速和输出功率有很大的影响.压电悬臂梁自由端添加质量块可以提高输出功率.风速15 m/s、外接200 kΩ优化负载时,采集器最大输出功率为64μW.     

A Vibration-Based PMN-PT Energy Harvester

We report design, modeling, analysis, and experimental study of a vibration-based piezoelectric energy harvester. The energy harvester is made of a composite cantilever of a single crystal relaxor ferroelectric material, $(1-x)$Pb(Mg $_{1/3}$Nb $_{2/3}$)O $_{3-x}$PbTiO $_3$ (PMN-PT), and a polydimethylsiloxane (PDMS) base layer. A PDMS proof mass is constructed at the tip of the composite cantilever beam and is used as a means to tune the system natural frequency. The use of the PMN-PT piezoelectric material and an interdigited electrodes (IDEs) design improves the energy conversion efficiency. A dynamic systems modeling approach is employed to analyze the responses and the performance of the harvester design. We have demonstrated that a prototype of the harvester with a size of 7.4 mm $,times,$2 mm $,times,$110 $mu$m outputs a voltage of 10 V (0.3 mW power) under a vibration excitation with a peak-to-peak amplitude of 1 mm at a frequency around 1.3 kHz. Based on the experimental results, the power density prediction of the proposed harvester design shows a superior performance than that of the other reported piezoelectric harvesters.