棕榈油碱催化制备生物柴油实验研究

用氢氧化钾作催化剂,考察了反应温度、催化剂用量、醇油摩尔比、反应时间对棕榈油和甲醇制备生物柴油产率的影响。结果表明,最佳反应条件为:反应温度40℃,催化剂用量0.6%,醇油摩尔比6∶1,反应时间2.0 h。此时,生物柴油产率可达97.82%。     

棕榈油碱催化制备生物柴油实验研究

用氢氧化钾作催化剂,考察了反应温度、催化剂用量、醇油摩尔比、反应时间对棕榈油和甲醇制备生物柴油产率的影响。结果表明,最佳反应条件为:反应温度40℃,催化剂用量0.6%,醇油摩尔比6∶1,反应时间2.0 h。此时,生物柴油产率可达97.82%。     

废弃油脂超临界法制备生物柴油研究

以废弃油脂为原料,利用超临界法制备生物柴油.通过单因素实验及正交实验研究了醇油摩尔比、反应压力、催化剂用量、反应时间、反应温度等因素对生物柴油产率的影响.结果表明,在实验范围内各影响因素对生物柴油产率作用的大小依次为:反应温度>反应压力>催化剂用量>反应时间>醇油摩尔比.废弃油脂超临界法制备生物柴油的最佳工艺条件为:反应温度240℃,反应压力10MPa,反应时间6min,催化剂用量0.06%,醇油摩尔比40/1.在此条件下,生物柴油产率达到99.37%.     

盐地碱蓬油制备生物柴油工艺条件研究

以盐地碱蓬油为原料制备生物柴油.通过正交实验研究了反应温度、催化剂用量、醇油摩尔比、反应时间、搅拌强度等因素对生物柴油产率的影响.结果表明,在实验范围内各影响因素对生物柴油产率作用的大小依次为:搅拌强度>反应时间>催化剂用量>醇油摩尔比>反应温度.盐地碱蓬油制备生物柴油的最佳工艺参数为:搅拌强度为1 800 r/min,反应时间60min,催化剂KOH用量为盐地碱蓬油质量的1%,醇油摩尔比6/1,反应温度65℃.在该工艺条件下,生物柴油产率达到97.03%.     

碘催化合成生物柴油的研究

在单质碘的催化作用下,玉米油和甲醇反应合成生物柴油。考察了反应时间、反应温度、催化剂的用量和醇油摩尔比各单因素对生物柴油产率的影响,得到最佳工艺条件:反应时间为90min,反应温度为70℃,催化剂用量为玉米油质量的0.5%,醇油摩尔比为6:1,生物柴油产率为75.27%。     

白云石非均相催化合成生物柴油的工艺研究

以大豆油、甲醇为原料,研究了通过白云石催化酯交换反应制取生物柴油的工艺的条件。用气相色谱-质谱分析法,并对反应温度、醇油摩尔比、反应时间、催化剂的用量及催化剂粒径进行考察,得出最佳合成条件为:反应温度65℃、反应时间2h、醇油摩尔比7:1,催化剂用量2%,催化剂粒径为80～150目,在此条件下得到生物柴油转化率为77.36%。     

活性炭负载碳酸钠催化猪油制备生物柴油

以猪油为原料,优化了活性炭负载碳酸钠催化猪油制备生物柴油的工艺。分别采用单因素实验和正交实验对反应条件进行了优化,考察了醇油摩尔比、催化剂用量、反应时间、反应温度的影响,结果表明最佳反应条件为:醇油摩尔比9∶1、催化剂用量为9%、反应时间3.5 h、反应温度70℃。在此条件下,生物柴油产率为95.3%。     

利用地沟油制备生物柴油技术的研究

本文提出了由地沟油生产生物柴油的新工艺,即在酸性催化剂(H_2SO_4)的作用先通过水解反应对地沟油进行预处理,然后进行酯化,将地沟油转化成生物柴油。探讨了醇油摩尔比、催化剂用量、反应温度和反应时间等工艺条件对生物柴油得率的影响。实验表明,最佳反应条件为:醇油摩尔比为5.3:1.催化剂(H_2SO_4)量为油的1.3%,反应温度65℃,反应时间为2小时,生物柴油得率高达90%.     

酯交换法制备生物柴油条件的研究

对一种山茶油利用酯交换法制备生物柴油的工艺条件进行研究,考察反应条件如醇油摩尔比、催化剂用量、反应时间、反应温度对反应产率和产品性质的影响,并确定最佳反应条件：醇油摩尔比为8：1,催化剂用量为1％,反应时间为30min,反应温度为40℃。     

蓖麻油质生物柴油的制备工艺研究

研究了蓖麻油在KOH的催化下与甲醇发生酯交换反应来制备生物柴油的研究。通过醇油比、反应时间、温度和催化剂用量等进行了单因素实验及正交实验的研究;结果表明蓖麻油制备生物柴油的最佳工艺为:醇油摩尔比为7∶1,催化剂用量为蓖麻油重的0. 8%,温度为35℃,时间为2 h,在此实验条件下最佳的产率为93. 74%。通过极差分析,影响蓖麻油质生物柴油合成的主要因素为反应时间和反应温度,醇油摩尔比的影响最小。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。