共查询到20条相似文献,搜索用时 328 毫秒
1.
本文以M2Al高速钢丝锥为研究对象,在常规热处理中引入深冷处理工艺,设计了四种不同的工艺对丝锥进行了处理,并进行攻丝试验,探究深冷处理工艺对丝锥寿命的影响.研究表明:深冷处理工艺有效的提高了丝锥的使用寿命,最优深冷工艺组丝锥攻丝孔数达到了88个,相较于常规工艺组寿命提高了1.6倍;通过微观分析发现耐磨性提高的原因是二次... 相似文献
2.
3.
4.
5.
6.
7.
8.
高速钢对焊丝锥断裂原因分析 总被引:1,自引:1,他引:0
1 问题的提出1998年我厂生产的G112 和M52规格的高速钢对焊丝锥 (刃部材质W6Mo5Cr4V2 ,柄部材质 4 5钢 )经对焊、机加工、淬火、回火后再进行机加工时 ,发现部分丝锥距高速钢刃部一侧出现横断裂纹 (见图 1和图 2 )。图 1 G112 丝锥裂纹部位图 2 M5 2丝锥裂纹部位通过对断裂丝锥作常规分析可知 :两种规格丝锥的化学成分均符合国家标准 ;刃部表面硬度合格( 63~ 64HRC) ;焊缝高速钢处金相组织符合要求。检查丝锥断口后可知 :①G112 丝锥断口位于距焊缝不远的高速钢刃部一侧 (与焊缝接近重合 ) ,断口从铣刀柄部加工平面直角根… 相似文献
9.
10.
11.
12.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
13.
三爪自定心卡盘作为机床的主要附件,已有一百多年的发展历史,尽管目前随着数控技术的不断发展,越来越多地需求高速动力卡盘,但三爪自定心卡盘目前仍有一定的市场。 要保证卡盘可靠地夹紧工件,必须使其有可靠的夹持精度;要保持卡盘的精度,必须要严格控制各零部件公差及误差,如盘丝的极心偏。 极心偏是形成圆的渐开线的基圆圆心 (极心 )与盘丝内孔中心不同心所造成的偏差值。它对卡盘精度的影响分两种情况,一是卡爪夹持弧采用配磨,二是卡爪夹持弧采用单磨。本文主要探讨配磨时的影响。 卡爪夹持弧采用配磨,即每台卡盘整体… 相似文献
14.
详细分析了圆柱面素线的直线度公差带在新旧标准中定义和解释的区别,并从对圆柱面素线实际要素检测的角度,提出了推行新标准的实际意义。 相似文献
15.
16.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
17.
根据广州市珠江新城旅客自动运输系统(APM)列车的运行特点,介绍APM列车制动系统的制动方式及其特点,分析APM列车动态制动和摩擦制动的工作机理及其区别和联系,阐明APM列车制动系统的电控制过程和气控制过程,从而为APM列车制动系统的维护和管理提供一定的依据. 相似文献
18.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
19.
我公司于80年代末引进Aspera公司年产80万台冰箱(冷柜)压缩机生产线及软件技术,在压缩机加工中,活塞销孔(如图1所示)的加工是难点之一。用镗床加工,质量一直难以达到要求,废品率很高。后来我们将Aspera公司的加工工艺即精镗后滚光改为精镗后用金刚石铰刀粗、精铰孔,由此解决了这个技术难题。(1)原意大利Aspera公司工艺简述其工艺流程为:钻6.5通孔→扩孔至7+0.1→粗镗7.473+0.036、圆柱度0.01→精镗至7.935+0.006、圆柱度0.002→滚光7.938+0.006、圆柱度0… 相似文献