Bioimaging TOF-SIMS: High resolution 3D imaging of single cells

The distribution of phosphocholine ions (m/z 184, m/z 86), sodium ions, and potassium ions in thyroid tumor cells was analyzed by imaging TOF-SIMS. Repeated sputtering with a C(60) (+) source and subsequent analysis with a Bi(3) (+) gun produced a series of 138 images that were stacked to make a 3D display of the chemistry of cells. Phosphocholine was seen in the plasma membrane (m/z 184) and intracellular membranes (m/z 86). The different fragmentation of the phospholipid probably reflects the chemical composition of membranes at these sites. High intensity of secondary ion signals of potassium was seen in membrane-encompassed cellular compartments. The data indicate that potassium ions are compartmentalized in thyroid tumor cells.     

Direct imaging of paracrystalline phospholipid structure in the electron microscope

A long chain amphiphilic molecule—the phospholipid 1,2-dihexadecyl sn glycerophosphoethanolamine—has been crystallized epitaxially so that the interlamellar molecular periodicity is parallel to the substrate and hence normal to the electron beam in the electron microscope. This has permitted the direct resolution of the 55·6 Å lamellae in unstained crystals at room temperature. The lattice images have shown the presence of line dislocations and lenticular cracks in the crystals. Of significance to their biological properties is that the lattice is undulating with a periodicity of 0·1–0·5 μm. This would also account for the difficulties encountered by X-ray and electron diffraction techniques when examining these crystals.     

The structure of (100) defects in carbonated apatite crystallites: a high resolution electron microscope study

Planar defects parallel to (100) with an approximate [1/400] displacement vector have been identified by high resolution transmission electron microscopy and by micro-electron diffraction in the center of synthetic carbonated apatite crystallites. Similar intergrowths, 0.8-1.5 nm in width, have been observed in dental enamel, dentin and bone apatite crystallites. Four possible structural models of the defect core are proposed to explain these experimental features, and computer-simulated lattice images of the models are compared with the experimental images. Typical defects were consistent with a two-dimensional octacalcium phosphate inclusion, one unit cell thick, embedded in an apatite matrix.     

信息产品的人机界面研究

信息产品在满足人的生理需求的同时,更主要的是满足人在使用过程中信息传达的心理表现.这涉及到人的思维动机、目的及作用方式,因此人机界面设计是信息产品的核心问题.从信息产品界面设计的理论出发,以典型信息产品--手机为主要分析对象,重点对其硬界面设计因素进行了分析研究,并提出一套手机界面设计方案.     

一种提高太赫兹波成像分辨力的方法

成像分辨力低是影响太赫兹波成像系统在质检、安全和医疗领域应用的重要因素之一。用返波管（BWO）作为太赫兹波辐射源搭建了一个连续太赫兹波点扫描透射成像系统。采用扫描步长小于系统聚焦光斑尺寸的方式获得样品物体的太赫兹透射图像,并利用增量维纳滤波法对该图像进行复原获得了超过系统衍射极限分辨力的太赫兹图像。实验结果表明该方法可以有效提高太赫兹波成像的空间分辨力。     

High resolution electron microscopy of partial dislocations in the Laves phase structure

A Mg-base Laves phase was investigated by high resolution electron microscopy (HREM). Linear defects found at terminations of stacking faults were classified into three groups. The first is a partial dislocation at a termination of a stacking fault, the second is a superposed partial dislocation which is defined as a defect produced by a superposition of terminations of two or more stacking faults lying on neighbouring layers, and the third is a combined linear defect which consists of a characteristic combination of terminations of stacking faults. In the last case the total stacking fault vector becomes equal to the translation vector in the basal plane, so that the defect needs no relaxation of the lattice. The Burgers vectors of the partial dislocations were estimated with the aid of modified Burgers circuits.     

A method using an on-line digital computer for the improvement of resolution of backscattered electron images

In principle, the resolution of backscattered electron (BSE) images can be little improved, even though an infinitely small beam size is achieved by various improvements in the intrinsic instrument. In order to circumvent this problem, a method is proposed which utilizes an on-line digital computer for the image recording and processing. The major image-processing tools are reduction, expansion, super-imposition with matching of the images, and high-emphasis filtering in the Fourier domain. By using various combinations of these techniques, the resolution of BSE images has been significantly improved. The validity of these improved images has been confirmed. In the case of a BSE image with too wide a dynamic range, both the present method and digital homomorphic filtering provide successful results.     

Experimental verification of the interface wave method to detect interlaminar damage of a metal multilayer structure

The interface wave traveling along the boundary of two materials has been studied for nearly a century. However, experiments, engineering applications, and interface wave applications to the non-destructive inspection of interlaminar composite have developed slowly. In this research, an experiment that applies Stoneley waves (a type of interfacial wave between two solid half-spaces) is implemented to detect the damage in a multilayer structure. The feasibility of this method is also verified. First, the wave velocity and wave structure of Stoneley waves at a perfectly bonded aluminum-steel interface are obtained by solving the Stoneley wave dispersion equation of two elastic half-spaces. Thereafter, an experiment is conducted to measure the Stoneley wave velocity of an aluminum-steel laminated beam and to locate interlaminar cracks by referring to the Stoneley wave velocity and echo wave time. Results indicate that the location error is less than 2%. Therefore, Stoneley waves show great potential as a non-destructive inspection method of a multilayer structure.     

High resolution images of a reconstructed surface structure on (111) gold platelets: Interpretation and comparison with theoretical models

Reconstruction of the (111) gold surface has been previously observed, and it has been shown that the surface net is compressed in the <110> direction, as compared with the bulk lattice. We present here some high resolution studies made on this surface reconstruction: the problem was to obtain a structure image corresponding mainly to the uppermost plane which forms the surface. For this, we have formed high resolution images by interferences between the so-called forbidden diffracted beams $\text{1}\text{3}$ (4?22): bulk gold, when observed along the <111> direction, is better described as a stacking of hexagonal two-dimensional layers, and the $\text{1}\text{3}$ (4?22) beams occur as diffracted beams from 1 (or2) hexagonal layers; they nearly disappear every 3 slices. If the top layer is reconstructed, the diffracted beams from the first slice will be different and will not cancel with the diffracted beams from the bulk layers. Hence the image formed with these beams will give some information on the reconstructed top layer. Computed images have been obtained for different models of the reconstructed surface. They show that, indeed, images obtained under these conditions are linked with the topography of the surface. They also show the importance of different experimental parameters, in particular the beam divergence.     

CVT lubrication: The effect of lubricants on the frictional characteristics of the belt-pulley interface

Two tests for evaluating continuously variable transmission (CVT) lubricants have been developed using readily available test equipment and test parts. These tests have been designed to rank lubricants using a number of criteria relevant to the performance of the lubricant in a push-belt variator. These include overall level of friction, friction stability, temperature dependence of friction, and load dependence of friction. Testing lubricants of different types has shown the effect of lubricant chemistry on the parameters measured and indicates that some existing fluids, a CVT fluid and passenger car motor oil, as well as an experimental fluid, should give good performance in a continuously variable transmission using a push-belt variator.     

Electron crystallography at atomic resolution: The structure of the odd-chain paraffin n-tritriacontane

The crystal structure of the odd-chain paraffin, n-tritriacontane, nC₃₃H₆₈, is determined directly by using low-dose electron microscope images and electron diffraction intensity data from epitaxially grown microcrystals. Phases of the most intense “polyethylene” reflections are determined from triplet structure-invariant relationships often used in X-ray crystallography. Low-dose electron microscopic images provide phases of the low-angle “lamellar” reflections and these can be used with one-dimensional structure-invariant relationships to determine other phases on the 00? reciprocal row. The phase set is sufficient to calculate an electrostatic potential map which is directly interpretable as a structure image at atomic resolution.     

High resolution biological scanning electron microscopy: A comparative study of low temperature metal coating techniques

Structural information on the surface of biological specimens can be resolved within molecular dimensions by “in-lens” field emission scanning electron microscopes when cryo-methods are used to adequately preserve the native state of the specimen. The visual definition of molecular surface structures depends largely on the metal coating. The thickness of the coating, as well as the temperature at which it is deposited, are among the most important parameters affecting visual definition. These were evaluated on T4 polyheads and T4D phages using chromium double-axis rotary shadowing (DARS). Micrographs of optimally DARS coated T4 polyheads and T4D phages were compared with chromium planar-magnetron sputtering (PMS) and unidirectional shadowing with platinum/carbon. Metal deposition was carried out at low temperatures during all three procedures. Optimal visual definition of structural details on the surface of DARS coated T4 polyheads and T4D phages (capsomeres of T4 polyheads and their subunits with diameters of 8 and 3 nm; T4D phage tail fibres with a thickness of 3 nm) is achieved at a thickness of the chromium film greater than the minimum required for metal film coalescence. Chromium DARS coating at room temperature resulted in poor structural definition, whereas DARS at specimen temperatures of ?85°C and ?150°C, with the chromium thickness optimized for each temperature, yielded good visual detail of polyhead substructures. The visual definition was slightly reduced when DARS coating was carried out at a specimen temperature of ?250°C. Adequate structural visibility of T4D phage and T4 polyhead surface structures was achieved with the three coating techniques tested. Smaller filamentous structures, however (e.g., phage tail fibres), were more clearly identified after chromium DARS coating or unidirectional platinum/carbon shadowing than after optimized PMS with chromium. Each method has its own merits.     

Atomic resolution imaging of beryl: an investigation of the nano‐channel occupation

Beryl in different varieties (emerald, aquamarine, heliodor etc.) displays a wide range of colours that have fascinated humans throughout history. Beryl is a hexagonal cyclo‐silicate (ring‐silicate) with channels going through the crystal along the c‐axis. The channels are about 0.5 nm in diameter and can be occupied by water and alkali ions. Pure beryl (Be₃Al₂Si₆O₁₈) is colourless (variety goshenite). The characteristic colours are believed to be mainly generated through substitutions with metal atoms in the lattice. Which atoms that are substituted is still debated it has been proposed that metal ions may also be enclosed in the channels and that this can also contribute to the crystal colouring. So far spectroscopy studies have not been able to fully answer this. Here we present the first experiments using atomic resolution scanning transmission electron microscope imaging (STEM) to investigate the channel occupation in beryl. We present images of a natural beryl crystal (variety heliodor) from the Bin Thuan Province in Vietnam. The channel occupation can be visualized. Based on the image contrast in combination with ex situ element analysis we suggest that some or all of the atoms that are visible in the channels are Fe ions.     

MRT Letter: High resolution SEM imaging of nano‐architecture of cured urea‐formaldehyde resin using plasma coating of osmium

Nanoarchitecture of cured urea‐formaldehyde (UF) resins was examined with a field‐emission scanning electron microscope (FE‐SEM) after coating samples with osmium, which is considered to produce particles of considerably smaller size compared to other metal coatings used in SEM studies. This method enabled comparison of the nanoarchitecture of UF resins of low (1.0) and high (1.6) formaldehyde/urea (F/U) mole ratios to be made, based on imaging of extremely small size particles as part of UF resin architecture, not described before. Imaging revealed presence of relatively large globular particles (148.084–703.983 nm size range) as well as smaller substructures (28.004–39.604 nm size range) as part of the architecture of 1.0‐mole UF resin. Globular particles were also present in 1.6 mole UF resin, but of considerably smaller size (14.760–50.269 nm). The work presented demonstrates usefulness of osmium coating in unraveling the intricacies of the nanostructural organization of cured UF resins, prompting wider application of this immensely useful but grossly underutilized metal coating type in high resolution SEM examination of biological and materials samples. Microsc. Res. Tech. 76:1108–1111, 2013. © 2013 Wiley Periodicals, Inc.     

Quantitative high resolution transmission electron microscopy: the need for energy filtering and the advantages of energy-loss imaging

Evidence is presented that inelastically scattered electrons contribute significant detail at the atomic level to high resolution images, particularly in high voltage instruments. The implications for quantitative image interpretation are shown to be serious and a case is made for incorporating facilities for energy-filtered imaging in future high resolution electron microscopes.     

Oriented immobilization of Pseudomonas putida putidaredoxin at a gold (111)–buffer interface: a real time scanning tunnelling microscopy study

A scanning tunnelling microscopy study of adsorption of wild‐type Pseudomonas putida putidaredoxin at a gold (111)–buffer interface has been made in real time. Reversible adsorption has been observed reflecting weak interaction of the wild‐type protein with a gold (111) electrode. A genetically engineered mutant, C73S‐D58C, which contains a surface thiol, has been used for ‘immobilization’ and ‘orientated adsorption’ on the gold surface. The implication of such orientated immobilization in development of a bio‐electrode surface has been predicted.     

Studying the resistivity imaging of chicken tissue phantoms with different current patterns in Electrical Impedance Tomography (EIT)

A current injection pattern in Electrical Impedance Tomography (EIT) has its own current distribution profile within the domain under test. Hence, different current patterns have different sensitivity, spatial resolution and distinguishability. Image reconstruction studies with practical phantoms are essential to assess the performance of EIT systems for their validation, calibration and comparison purposes. Impedance imaging of real tissue phantoms with different current injection methods is also essential for better assessment of the biomedical EIT systems. Chicken tissue paste phantoms and chicken tissue block phantoms are developed and the resistivity image reconstruction is studied with different current injection methods. A 16-electrode array is placed inside the phantom tank and the tank is filled with chicken muscle tissue paste or chicken tissue blocks as the background mediums. Chicken fat tissue, chicken bone, air hole and nylon cylinders are used as the inhomogeneity to obtained different phantom configurations. A low magnitude low frequency constant sinusoidal current is injected at the phantom boundary with opposite and neighboring current patterns and the boundary potentials are measured. Resistivity images are reconstructed from the boundary data using EIDORS and the reconstructed images are analyzed with the contrast parameters calculated from their elemental resistivity profiles. Results show that the resistivity profiles of all the phantom domains are successfully reconstructed with a proper background resistivity and high inhomogeneity resistivity for both the current injection methods. Reconstructed images show that, for all the chicken tissue phantoms, the inhomogeneities are suitably reconstructed with both the current injection protocols though the chicken tissue block phantom and opposite method are found more suitable. It is observed that the boundary potentials of the chicken tissue block phantoms are higher than the chicken tissue paste phantom. SNR of the chicken tissue block phantoms are found comparatively more and hence the chicken tissue block phantom is found more suitable for its lower noise performance. The background noise is found less in opposite method for all the phantom configurations which yields the better resistivity images with high PCR and COC and proper IR_Mean and IR_Max neighboring method showed higher noise level for both the chicken tissue paste phantoms and chicken tissue block phantoms with all the inhomogeneities. Opposite method is found more suitable for both the chicken tissue phantoms, and also, chicken tissue block phantoms are found more suitable compared to the chicken tissue paste phantom.     

Observation of lattice fringes of the Si(111)–7×7 structure by reflection electron microscopy*

Lattice fringes of Si(111)–7×7 reconstructed surface structure in reflection electron microscopy (REM) are observed for the first time, and their characteristic features are presented. Due to a glancing reflection condition in REM, the fringes with a spacing of 2.3 nm of the 7×7 surface structure lattice are seen in a region of a certain defocus range (about 6–8 μm) in a foreshortened image. The glancing reflection geometry also results in a complicated dependence of fringe directions on imaging conditions (beam alignment, crystal orientation). A shift of the fringes across the surface atomic steps and out of phase boundaries is observed.     

Towards 1.0 Å resolution: taking advantage of dynamical scattering, and the benefits for structure retrieval

This paper is an exploration of the behaviour of high-resolution transmission electron microscope (HRTEM) images at up to 1 Å resolution. The ultimate limits to HRTEM (structure) resolution and the manner in which strong scattering may lead to weak diffraction in heavy fcc metals are discussed. A resolution of 1.0 Å is somewhat better than the ultimate resolution presently achievable in a 400-kV electron microscope. In heavy metals, such as platinum, it is found that the lattice fringe contrast is very low in the [011] projection, but that fringe contrast may be improved by imaging in the [111] projection. For atomic resolution imaging of the heavy metals in the [111] projection a resolution of 1.2 Å is required. For the study of oxygen position in high-temperature superconducting (HTS) oxides a resolution of between 1.2 and 1.4 Å is required. At better than 1.2 Å resolution the thick crystal images in HTS oxides remain simple and are easily interpreted. At such resolution all atomic columns are separated for the HTS [010] projection and the dynamical diffraction effects improve the contrast of oxygen atoms relative to the metal atoms.