Spherical-Impact Damage and Strength Degradation in Silicon Carbide Whisker/Silicon Nitride Composites

The silicon carbide (SiC) whisker reinforcement of silicon nitride (Si₃N₄) improves fracture strength and toughness, hardness, and Young's modulus, resulting in higher resistance of the composites to sphere penetration and crack initiation at spherical impact. Sintered Si₃N₄ shows an elastic/plastic response and initiates median/radial cracks at 100 m/s impact velocity. SiC-whisker/Si₃N₄ composites, on the other hand, demonstrate an elastic response, with Hertzian cone crack initiation, only when impact velocity exceeds 280 m/s. The SiC-whisker/Si₃N₄ composites thus exhibit improved strength degradation versus critical impact velocity characteristics because of improved mechanical properties provided by the SiC whiskers.     

R-Curve Behavior of Silicon Nitride Ceramic Reinforced with Silicon Carbide Platelets

Si₃N₄ ceramics reinforced with SiC platelets were fabricated by hot pressing at 1800°C. The microstructure of the Si₃N₄ matrix itself was the same with or without the addition of the SiC platelets. However, the mechanical properties of the Si₃N₄ were changed remarkably by the SiC addition. The fracture toughness and the crack resistance with crack propagation ( R -curve behavior) were improved while the fracture strength was decreased slightly by the platelets. Improvement in crack resistance was attributed to the extensive interaction of cracks with the platelets. The reduction in strength, on the other hand, is believed to be due to cracks associated with weak platelet-matrix interfaces.     

Control of Composition and Structure in Laminated Silicon Nitride/Boron Nitride Composites

Based on a biomimetic design, Si₃N₄/BN composites with laminated structures have been prepared and investigated through composition control and structure design. To further improve the mechanical properties of the composites, Si₃N₄ matrix layers were reinforced by SiC whiskers and BN separating layers were modified by adding Si₃N₄ or Al₂O₃. The results showed that the addition of SiC whiskers in the Si₃N₄ matrix layers could greatly improve the apparent fracture toughness (reaching 28.1 MPa·m^1/2), at the same time keeping the higher bending strength (reaching 651.5 MPa) of the composites. Additions of 50 wt% Al₂O₃ or 10 wt% Si₃N₄ to BN interfacial layers had a beneficial effect on the strength and toughness of the laminated Si₃N₄/BN composites. Through observation of microstructure by SEM, multilevel toughening mechanisms contributing to high toughness of the laminated Si₃N₄/BN composites were present as the first-level toughening mechanisms from BN interfacial layers as crack deflection, bifurcation, and pull-out of matrix sheets, and the secondary toughening mechanism from whiskers in matrix layers.     

Impact Damage and Strength Degradation in a Silicon Carbide Reinforced Silicon Nitride Composite

Adding SiC particles to Si₃N₄ and subjecting the mixture to a sinter-hot-isostatic-pressing process increases both the strength and elastic modulus. It also decreases the hardness but maintains the fracture toughness, which results in a higher resistance to crack initiation and propagation during spherical particle impact. Sinter-hot-isostatically-pressed composites exhibit elastic response as their dominant behavior. They also display a high resistance to Hertzian cone crack initiation and extension. This is due to the increased degree of inelastic deformation of sinter-hot-isostatically-pressed composites.     

Reaction-Bonded and Superplastically Sinter-Forged Silicon Nitride–Silicon Carbide Nanocomposites

Silicon nitride–silicon carbide (Si₃N₄–SiC) nanocomposites were fabricated by a process involving reaction bonding followed by superplastic sinter-forging. The nanocomposites exhibited an anisotropic microstructure, in which rod-shaped, micrometer-sized Si₃N₄ grains tended to align with their long axes along the material-flow direction. SiC particles, typically measuring several hundred nanometers, were located at the Si₃N₄ grain boundaries, and nanosized particles were dispersed inside the Si₃N₄ grains. A high bending strength of 1246 ± 119 MPa, as well as a high fracture toughness of 8.2 ± 0.9 MPa·m^1/2, was achieved when a stress was applied along the grain-alignment direction.     

Toughening of Silicon Nitride Matrix Composites by the Addition of Both Silicon Carbide Whiskers and Silicon Carbide Particles

Si₃N₄ matrix composites reinforced by SiC whiskers, SiC particles, or both were fabricated using the hot-pressing technique. The mechanical properties of the composites containing various amounts of these SiC reinforcing materials and different sizes of SiC particles were investigated. Fracture toughness of the composites was significantly improved by introducing SiC whiskers and particles together, compared with that obtained by adding SiC whiskers or SiC particles alone. On increasing the size of the added SiC particles, the fracture toughness of the composites reinforced by both whiskers and particles was increased. Their fracture toughness also showed a strong dependence on the amount of SiC particles (average size 40 μm) and was a maximum at the particle content of 10 vol%. The maximum fracture toughness of these composites was 10.5 MPa·m^1/2 and the flexural strength was 550 MPa after addition of 20 vol% of SiC whiskers and 10 vol% of SiC particles having an average particle size of 40 μm. These mechanical properties were almost constant from room temperature to temperatures around 1000°C. Fracture surface observations revealed that the reinforcing mechanisms acting in these composites were crack deflection and crack branching by SiC particles and pullout of SiC whiskers.     

Combustion Synthesis of Silicon Nitride-Silicon Carbide Composites

The feasibility of synthesizing silicon nitride-silicon carbide composites by self-propagating high-temperature reactions is demonstrated. Various mixtures of silicon, silicon nitride, and carbon powders were ignited under a nitrogen pressure of 30 atm (∼ 3 MPa), to produce a wide composition range of Si₃N₄-SiC powder products. Products containing up to 17 vol% of SiC, after being attrition milled, could be hot-pressed to full density under 1700°C, 3000 psi (∼ 21 MPa) with 4 wt% of Y₂O₃. The microhardness and fracture toughness of these composites were superior to those of the pure β-Si₃N₄ matrix material and compared very well with the properties of "traditionally" prepared composites.     

Effect of Silicon Carbide Whisker and Titanium Carbide Particulate Additions on the Friction and Wear Behavior of Silicon Nitride

A Si₃N₄/TiC composite was previously demonstrated to exhibit improved wear resistance compared to a monolithic Si₃N₄ because of the formation of a lubricious oxide film containing Ti and Si at 900°C. Further improvements of the composite have been made in this study through additions of SiC whiskers and improved processing. Four materials—Si₃N₄, Si₃N₄/TiC, Si₃N₄/SiC_wh, and Si₃N₄/TiC/SiC_wh— were processed to further optimize the wear resistance of Si₃N₄ through improvements in strength, hardness, fracture toughness, and the coefficient of friction. Oscillatory pin on flat wear tests showed a decrease in the coefficient of friction from ∼0.7 (Si₃N₄) to ∼0.4 with the addition of TiC at temperatures reaching 900°C. Wear track profiles illustrated the absence of appreciable wear on the TiC-containing composites at temperatures above 700°C. Microscopic (SEM) and chemical (AES) characterization of the wear tracks is also included to deduce respective wear and lubricating mechanisms.     

Chemical-Vapor-Infiltrated Silicon Nitride, Boron Nitride, and Silicon Carbide Matrix Composites

Composites of carbon/chemical-vapor-deposited (CVD) Si₃N₄, carbon/CVD BN, mullite/CVD SiC, and SiC yarn/CVD SiC were prepared to determine if there were inherent toughness in these systems. The matrices were deposited at high enough temperatures to ensure that they were crystalline, which should make them more stable at high temperatures. The fiber-matrix bonding in the C/Si₃N₄ composite appeared to be too strong; the layers of BN in the matrix of the C/BN were too weakly bonded; and the mullite/SiC composite was not as tough as the SiC/SiC composites. Only the SiC yarn/CVD SiC composite exhibited both strength and toughness.     

Microstructure and Mechanical Properties of Sinter–Post-HIPed Si3N4–SiC Composites

The microstructural evolution and mechanical properties of Si₃N₄–SiC composites obtained by the sinter–post-HIP process were investigated. SiC addition prohibited β-Si₃N₄ grain growth; however, the grain growth followed the empirical growth law, with exponents of 3 and 5 for the c - and the a -axis directions, respectively. Mechanical properties were strongly influenced by SiC addition and sintering conditions. Short-crack propagation behavior was measured and analyzed by the indentation-strength in-bending (ISB) method. The present composites had high short-crack toughness, compared with the values for monolithic Si₃N₄. The enhanced short-crack toughness was attributed to crack-tip bridging by the SiC particles.     

Si3N4/SiC-Whisker Composites without Sintering Aids: II, Fracture Behavior

The fracture behavior of an Si₃N₄/SiC-whisker composite fabricated without sintering aids is investigated using a double approach based on the examination of R -curve behavior and a statistical analysis of crack propagation. In the composite with 20 vol% whisker, a 30% increase in toughness over the matrix value can be attributed to crack-tip phenomena. Strong interfacial bonding prevents any contribution to toughening by mechanisms operating in the wake region of the crack. Based on experimental observations of microfracture in both SiC whiskers and Si₃N₄ grains, toughening caused by crack-tip phenomena is quantitatively discussed in terms of fracture energy and whisker-distribution parameters.     

Effect of a Silicon Carbide "Nano-Dispersion" on the Mechanical Properties of Silicon Nitride

The hypothesis that a synergistic effect by fine SiC dispersoids operating on the submicrometer scale is capable of enhancing the deformation and fracture properties of Si₃N₄ ceramics has been examined. In order to single out the effect of the SiC dispersion from other microstructural factors affecting the material properties, experiments were conducted on a highly pure and dense Si₃N₄ material, suitable for basic investigations. Fracture mechanics and creep characterizations were performed at room temperature and at 1400°C on composites containing 25 vol% submicrometer SiC particles, for which the intragranular fraction was varied by changing the sintering conditions. Despite the obtained difference in composite microstructure, almost no improvement in either the fracture toughness or strength, as compared with the monolithic material, was found. Similarly, the slow crack growth and creep resistance at 1400°C were still dictated by the inherent properties of the matrix. This study emphasizes the need for scientific rather than empirical approaches on simple systems, before deducing general rules for the microstructural design of structural ceramics.     

R-Curve Behavior of Si3N4–BN Composites

R -curve behavior of Si₃N₄–BN composites and monolithic Si₃N₄ for comparison was investigated. Si₃N₄–BN composites showed a slowly rising R -curve behavior in contrast with a steep R -curve of monolithic Si₃N₄. BN platelets in the composites seem to decrease the crack bridging effects of rod-shaped Si₃N₄ grains for small cracks, but enhanced the toughness for long cracks as they increased the crack bridging scale. Therefore, fracture toughness of the composites was relatively low for the small cracks, but it increased significantly to ∼8 MPa·m^1/2 when the crack grew longer than 700 μm, becoming even higher than that of the monolithic Si₃N₄.     

Mechanical Properties of β-Si3N4-Whisker/Si3N4-Matrix Composites

Composites containing 30 vol%β-Si₃N₄ whiskers in a Si₃N₄ matrix were fabricated by hot-pressing. The composites exhibited fracture toughness values between 7.6 and 8.6 MPa · m^1/2, compared to 4.0 MPa · m^1/2 for unreinforced polycrystalline Si₃N₄. The improvements in fracture toughness were attributed to crack wake effects, i.e., whisker bridging and pullout mechanisms.     

Fracture Toughness of a Silicon Nitride/Silicon Carbide Nanocomposite at 1350°C

The fracture toughness of a hot-pressed silicon nitride/silicon carbide (Si₃N₄/SiC) nanocomposite and reference monolithic Si₃N₄ has been investigated in four-point bending at 1350°C in air, using different loading rates (0.01-1 mm/min). Single-edge V-notched bend specimens that were prepared by polishing the notch tip to a radius of <10 µm, using 1 µm diamond paste, were used for the fracture toughness measurement. Slow crack growth (SCG) prior to catastrophic failure was detected at all applied loading rates at 1350°C. The fracture toughness at 1350°C, as calculated using the actual crack size measured on the fracture surface after the bend test, increased in both ceramics with decreasing loading rate and increasing area of the SCG region.     

Improved Resistance to Damage of Silicon Carbide-Whisker-Reinforced Silicon Nitride-Matrix Composites by Whisker-Oriented Alignment

The effects of whisker-oriented alignment on resistance to damage of SiC( w )/Si₃N₄ composites have been investigated by the Vickers indentation method and R -curve behavior. It is shown that increasing the degree of whisker-oriented alignment decreases the lengths of Vickers impressions and indentation cracks. The results exhibit rising R -curve behaviors for the SiC( w )/Si₃N₄ composites with different degree of whisker-oriented alignment. Moreover, the initial crack length c _i, the threshold of crack growth resistance K _i, and the upper bound of crack growth resistance K _∞ change regularly with increasing degree of whisker-oriented alignment. All results suggest that the whisker-oriented alignment improves the resistance to damage of the composites, resulting in a more reliable and usable composite.     

Burner Rig Hot Corrosion of Silicon Carbide and Silicon Nitride

A number of commercially available SiC and Si₃N₄ materials were exposed to 1000°C for 40 h in a high-velocity, pressurized burner rig as a simulation of an aircraft turbine environment. Na impurities (2 ppm) added to the burner flame resulted in molten Na₂SO₄ deposition, attack of the SiC and Si₃N₄, and formation of substantial Na₂O. x (SiO₂) corrosion product. Room-temperature strength of the materials decreased as a result of the formation of corrosion pits in SiC and grain-boundary dissolution and pitting in Si₃N₄.     

Mechanical Properties of Si2N2O/SiC-Whisker Composites

The mechanical and thermal properties of Si₂N₂O/SiC-whisker composites were studied with emphasis on the effect of matrix composition and of whisker content. The fracture toughness of Si₂N₂O was remarkably improved by 90% with a concomitant 70% strength improvement by addition of SiC whiskers of only 10 vol%. Optimum mechanical and thermal properties of Si₂N₂O/SiC-whisker composites were obtained at an equimolar ratio of Si₃N₄/SiO₂, which is the stoichiometric composition for Si₂N₂O. Additional investigation concerning the Si₂N₂O-matrix/SiC-whisker interface by controlling sintering additives is necessary for further improvement of mechanical and thermal properties of Si₂N₂O/SiC-whisker composites.     

In Situ Polysilane-Derived Silicon Carbide Particulates Dispersed in Silicon Nitride Composite

A dense (97% of theoretical density) Si₃N₄—SiC composite containing 10 wt%β-SiC was prepared by introducing a SiC phase by the pyrolysis of a polymeric SiC precursor. The composite material was produced by mixing an alkyl/aryl-substituted polysilane with Si₃N₄ powder and, by subsequently forming green compacts, pyrolyzing the polymeric species, and finally sintering the sample. Synthesis and characterization of the polymeric compound was described. Its transformation reactions to SiC and the characterization of the ceramic residue were also studied. High ceramic yields were obtained by curing the as-synthesized polysilane at 500°C in an Ar atmosphere. The heat treatment had no effect on the good solubility of the polymeric precursor in organic solvents. This was important for processes such as infiltration, sealing, and coating and for the mixing of the polymer with powders for the preparation of homogeneous composite ceramics. The dense microstructure of the pyrolyzed and sintered Si₃N₄ powder–polysilane mixture exhibited reduced grain growth of the Si₃N₄ particles and a very homogeneous distribution of the in situ-formed β-SiC phase.     

Fractography, Mechanical Properties, and Microstructure of Commercial Silicon Nitride–Titanium Nitride Composites

Commercial-grade Si₃N₄–TiN composites with 0, 10, 20, and 30 wt% TiN content have been characterized. Submicrometer grain-size Si₃N₄ was reinforced with fine TiN grains. Density, Young's modulus, coefficient of thermal expansion, and fracture toughness increased linearly with TiN content. Increased strength was observed in the Si₃N₄+20 wt% TiN, and Si₃N₄+30 wt% TiN composites. Fractography was used to characterize the different types of fracture origins. Improvements in toughness and strength are due to residual stresses in the Si₃N₄ matrix and the TiN particles. A threefold improvement in dry wear resistance of the Si₃N₄+30 wt% TiN composite over the Si₃N₄ matrix was observed.