60GHz全双工OFDM-ROF系统的实验研究

研究了基于光外部调制的方式产生60GHz光毫米波的全双工光纤无线(ROF)通信系统。实验利用29GHzRF源产生58GHz的光载毫米波,2.5Gbit/s OFDM信号作为下行数据信号调制到光载毫米波上并传输光纤20km,在基站与用户单元实现3.3m的无线传输。同时实现了下行信号中心载波重利用作为上行信号的光载波,2.5Gbit/s的OOK信号作为上行数据信号调制到光载波上经20km上行链路光纤传输至中心站。     

全双工光载无线通信链路模型研究

提出了一个新的全双工光载无线通信链路模型。方案的下行链路采用两个马赫曾德尔调制器级联以产生六倍频毫米波;采用单边带调制,有效防止了码元走离现象,提高了传输距离;上行链路复用了下行链路中的一阶光边带以作为上行基带信号的载波,从而无需在基站中额外配置激光源;采用延时零拍法解调,减少了对毫米波本地振荡器的需求,降低了系统的成本。仿真结果表明,所提出的全双工模型中,仅用10 GHz频率的调制信号就能产生60 GHz的毫米波,大大降低了调制信号频率,且下行链路传输距离可达250 km,而上行链路传输距离大于300 km。     

应用于光纤无线电系统的一种改进的光外差技术

在光纤无线电技术中,通过光外差产生毫米波具有结构简单、成本低的特点,但中心站一般需要使用相干光源.文章提出了一种改进的光外差法,系统分析和仿真试验表明,该方法不仅可以避免使用相干光源,而且中心站和无线终端都无需配备毫米波本振.同时中心站采用单边带的信号调制,还可以有效降低光纤色散引起的毫米波信号的衰落.     

基于受激布里渊散射的30GHz毫米波单边带调制生成技术

本文提出了一种基于受激布里渊散射原理的单边带调制产生30GHz毫米波的新方法,可应用于光载射频系统。该方法利用一个双布里渊散射移频结构生成泵浦光,并将其反向注入到传输信号光的25 km单模光纤;通过受激布里渊散射,直接放大受调制信号光的正三阶边带,实现光载波的单边带调制,有效改善由色散效应引入的功率涨落问题,保证了毫米波功率稳定。此外,信号光和泵浦光由同一个激光器产生,有效消除两者间的相对频率漂移,从而大大提升了毫米波生成系统的频率稳定性。通过我们的方法,实验系统所生成的毫米波功率增益了21dB,其3dB线宽为10kHz。     

基于直流光注入直调DFB-LD的可调光毫米波信号产生技术

提出了一种基于直流光注入直接调制分布反馈式半导体激光器(DFB-LD)的载波可调的光毫米波生成方案,利用直接调制DFB-LD的输出瞬态波长随驱动电流增大而蓝移的特点,将直流光注入至直调DFB-LD的0码波长附近注入锁定。锁定的直调激光器在1码时输出的蓝移波长与原注入波长相位相干,再通过光电探测器将拍频信号转换为调制的光毫米波信号。实验重点讨论了40GHz光毫米波的产生,同时完成了30、40、50和60GHz光毫米波的可调谐性实验。本文的方案结构简单,无需外调制器和微波本振,载波可调并可产生高至60GHz光毫米波信号,可作为光/无线混合接入中成本节省的光上变频方案。     

注入连续光实现锁模光纤激光器的波长稳定

提出了一种实现锁模光纤激光器波长稳定的方法,即向锁模激光器腔内注入连续光,使某一组纵模在注入连续光的基础上起振。这组纵模在对增益介质的竞争中可以稳定地占据优势,从而实现激光器输出光谱的稳定。理论分析发现注入连续光会使锁模激光器纵模线宽变大,而线宽的增大将会增加进入纵模的连续光功率。在实验中对基于掺铒光纤放大器(EDFA)的主动锁模光纤激光器进行波长稳定,激光器的调制频率为10.06 GHz,观察到了良好的稳定效果。为进一步检验波长稳定的效果,对锁模光纤激光器进行波长稳定后,将其输出的光信号经过一个法布里-珀罗(F-P)滤波器,稳定地滤出了功率较高的纵模。法布里-珀罗滤波器的自由光谱区(FSR)为40.24 GHz,透射峰3 dB带宽为40 MHz。实验结果证明纵模被稳定在法布里-珀罗滤波器的透射峰范围内,纵模波长的波动小于40 MHz。     

采用半导体光放大器进行直接调制的全双工光纤无线通信系统实验研究

提出并实验研究了一种将光源和光调制器集中于中心站,而基站中使用直接调制半导体光放大器的新型光纤无线通信系统,在中心站采用相位调制器和光交错复用器产生光毫米波,并同时将未调制信号的光载波与光毫米波一起发送到基站;在基站中将下行链路的光载波分离出来作为上行链路的光载波,并利用半导体光放大器将上行链路的信号调制到光载波上,同时对上行链路的信号进行放大.实验结果显示可以将下行链路中2.5Gbit/s的数据和上行链路中250Mbit/s的数据在单模光纤中传输40km.     

基于低速光调相信号注入DFB-LD产生4～16倍频的40GHz和60GHz毫米波信号

提出一种基于低速光调相信号注入半导体分布反馈激光器(DFB-LD)产生最低4倍频,最高16倍频的40GHz和60GHz的毫米波调相信号。该方案利用注入光的N阶调相边带锁定DFB-LD的波长,同时DFB-LD放大此调相边带并与原注入光信号通过相干差拍作用在LD腔内形成毫米波调相信号。通过理论建模分析了工作原理,经系统实验验证了此方案的可行性。应用2.5,5和10GHz的光调相信号均得到40GHz或60GHz的毫米波信号,实现了最低4倍频,最高16倍频的毫米波信号产生,并通过单边带相位噪声的测量验证了毫米波的频率稳定度。     

基于两个平行马赫-增德尔调制器的光载无线传输系统

为提高光载无线(radio over fiber,RoF) 传输系统中的光波信号的利用率,本文提出了一种基于两个平行马赫-增德尔调制器 (Mach-Zehnder modulator,MZM) 的RoF传输系统。两个平行MZM经射频(radio frequency,RF) 信号调制后,产生5个光边带信号,分别是正负一阶光边带、正负二阶光边带和光载波。其中正负二阶光边带使用基带数据进行调制,经光电检测器(photodiode,PD) 拍频后产生已调数据的毫米波信号,再由天线发射出去。正二阶边带和光载波经PD拍频后产生未调制数据的毫米波,该毫米波用于接收端解调的本振信号(local oscillator,LO) 。负二阶边带信号用于上行链路的光载波。在本系统中,5个光边带信号都被充分利用,提高了光信号的利用效率。此外,还分析了该系统通过色散介质的传输特性,为RoF通信系统提供了一种实用化的解决方案。     

改进的基于多倍频的单边带调制ROF全双工系统

利用单边带调制技术,设计了一种改进的毫米波光纤传输系统,进行了系统色散分析及仿真实验.该系统在中心站通过设置相位调制器的偏置电压,使调制器产生的奇数边带被抑制,采用滤波器滤出其中的一个二阶边带.基带信号经过中频调制形成副载波,再将此副载波通过单边带调制到二阶边带上;在基站,通过带通滤波器滤出上行链路所需的光载波.用该单...     

一种12倍频全双工RoF系统

为提高光载无线(RoF)通信系统倍频系数,提出了一种基于集成双平行马赫曾德尔调制器(MZM)和抑制载波光双边带调制的12倍频光生毫米波方案.理论分析了光生毫米波信号产生机理,讨论了相关参数对光生毫米波信号的影响,理论分析与仿真结果基本吻合.在此基础上设计了一种基于该方案的全双工RoF系统,通过调整基站(BS)线偏振器(...     

Microwave frequency up/downconversion based on dual-wavelength fibre laser

A novel method of microwave frequency up/downconversion is proposed for microwave/millimetre-wave-based radio-over-fibre (RoF) systems. The uplink and downlink are both based on dual-wavelength single-longitudinal-mode fibre laser modulation and heterodyning, which provides the possibility to realise bidirectional RoF transmissions.     

Full-Duplex 60-GHz RoF System With Optical Local Oscillating Carrier Distribution Scheme Based on FWM Effect in SOA

A full-duplex 60-GHz radio-over-fiber (RoF) system using novel optical local oscillating (LO) carrier distribution scheme to reduce the system cost and realize centralized management is proposed and experimentally demonstrated. In the proposed scheme, the optical LO carriers for producing remote electrical LO signals at the base stations (BSs) are generated together with the downlink RoF carriers at the central station (CS) via four-wave-mixing effect in semiconductor optical amplifier, and are then distributed to the BSs along with the downlink RoF signals. By down-converting the 60-GHz-band uplink signal with the remotely produced 60-GHz LO signal and reusing the optical LO carriers as the uplink optical source, only a cost-effective intermediate frequency modulator is required at each BS to transmit the uplink signal, which will dramatically reduce the whole system budget due to a large amount of BSs. Moreover, the operating frequency of each BS can be controlled remotely at the CS end to realize centralized management and convenient reconfiguration. Using the proposed scheme, 622-Mb/s signals for both directions are successfully transmitted over a 20-km single-mode fiber link and a 50-cm wireless channel with less than 0.1- and 0.2-dB power penalty for downlink and uplink, respectively.      

A novel scheme to implement duplex 60-GHz radio-over-fiber link with 20-GHz double-sideband optical millimeter-wave transmitted along the fiber

A duplex radio-over-fiber (RoF) link with a novel scheme to generate 60-GHz millimeter (mm)-wave using 20 GHz double sideband (DSB) optical mm-wave with signal carried only by its optical carrier is investigated. In the RoF downlink, the modulation frequency to generate the DSB optical mm-wave is reduced greatly. The theoretical analysis and numerical simulation show that this scheme cannot only eliminate the code form distortion caused by the time shifting of the sidebands, but also reduce the influence of the fading effect as the DSB optical mm-wave signal is transmitted along the fiber. Based on the scheme, the duplex RoF link with the frequency up- (down-) conversion of the down- (up-) link mm-wave signal is built and the uplink transmission performance is analyzed theoretically.     

应用光PSK调制的新型60 GHz ROF下行链路系统

文章提出一种将光相移键控(PSK)调制用于基于谐波生成原理的毫米波光纤无线电(ROF)下行链路系统,在生成毫米波的同时,实现了二进制相移键控(BPSK)调制,并且通过加入并行光载波抑制双边带调制(DSB-SC)支路实现了导频的产生,供毫米波下变频之用.仿真结果验证了毫米波的产生和信号的调制解调过程,证明了该下行链路系统的可行性.     

New progress of mm-wave radio-over-fiber system based on OFM

This paper presents an overview on new progresses-of millimeter wave (mm-wave) radio-over-fiber (RoF) system based on mm-wave generation by optical frequency multiplication (OFM), including gen-eration of high-order optical side modes by optical modulation using dual-drive Mach-Zehnder modulator (DD-MZM) and enhancement of high-order optical side mode induced by selective amplification due to stimulated Brillouin scattering (SBS). The paper describes OFM by using DD-MZM in principle and verifies it in an experimental bidirectional 40GHz RoF system. SBS amplification enhances the generated information-bearing mm-wave in downlink and also helps in producing a pure reference mm-wave for radio frequency-intermediate frequency (RF-IF) down-conversion in uplink. These efforts pushed the OFM technology of mm-RoF systems to achieve more and more feasibility and cost-effectiveness.     

基于FBG和偏振复用的8倍频全双工RoF系统

为简化光载无线通信系统(RoF)中心站(CS)和基站(BS)结构,提出了一种基于光纤布拉格光栅(FBG)和偏振复用技术的8倍频全双工RoF系统方案。通过设置马赫-曾德尔调制器(MZM)偏置电压和射频驱动信号幅度保留部分主载波与偶数阶边带,再利用FBG将主载波与偶数阶边带分离。结合偏振复用技术将主载波和偶数阶边带复用到X和Y两个偏振方向上,其中抑制载波偶数阶边带用于下行链路数据传输,而主载波在BS站作为上行链路载波使用。理论推导了实现机理并进行了实验验证,结果表明当使用10 GHz射频驱动时可实现稳定的80 GHz光载毫米波信号,传输20 km后下行链路和上行链路功率代价仅为0.1和0.07 dB,表现出了较好的系统性能。     

光载无线信号的OCS-DPSK调制格式

文章提出一种新型的光载波抑制一差分相移键控（OCS-DPSK）调制格式,可以实现光载无线（RoF）系统的3个关键功能：分发下行RoF信号、产生远端本振信号和上行数据的重调制,从而实现成本最优的RoF接入网络。文章作者实验演示了基于单个单臂马赫-曾德调制器产生OCS-DPSK控调制格式的全双工RoF传输系统。     

Full-Duplex 1.0 Gbit/s Data Transmission Over 60 GHz Radio-on-Fiber Access System Based on the Loop-Back Optical Heterodyne Technique

Full-duplex transmission over a 60 GHz radio-on-fiber access system based on the optical heterodyne technique is verified in this paper. With this technique, an optical carrier generator on the transmitting side consolidates the functions of wavelength and polarization control for optical heterodyne detection in uplinks and optical millimeter-wave generation in downlinks, on behalf of each optical transmitter/receiver. Therefore, the whole system configuration can be significantly simplified. A full-duplex 1.0 Gbit/s transmission experiment over 10 km of single-mode fiber, which represents an access network transmission, is demonstrated using the simultaneous modulation/photodetection operation of an electroabsorption modulator (EAM). Bit error rates of less than 10$^{-9}$ were obtained in both the uplink and downlink without noticeable mutual interference, even though the laser source and the EAM is shared by both links, and no significant dispersion-induced degradation was observed. Moreover, the experimental results showed that an optical link budget of 9.2 dB can be achieved with the experimental configuration.      

基于光学倍频技术的WDM-ROF-PON系统设计

设计了一种将光载无线技术融合于波分复用无源光网络结构的系统。在发射端,系统采用光学倍频技术生成40GHz光毫米波载波,加载2.5Gbit/s的基带数据信号,下行链路传输性能良好且受色散影响小;在接收端,利用光波重用技术从下行信号中提取上行光载波,加载2.5Gbit/s上行基带数据信号。采用光学倍频技术降低了毫米波生成成本,提高了系统的实用性。