Differences in enthalpy recovery of gradient and random copolymers of similar overall composition: styrene/4-methylstyrene copolymers made by nitroxide-mediated controlled radical polymerization

Styrene/4-methylstyrene (S/MS) random and gradient copolymers were synthesized by nitroxide-mediated controlled radical polymerization (NM-CRP) and compared to random copolymers made by conventional free radical polymerization (ConvFRP). The gradient copolymers have molecular weight (MW) values approaching 85,000 g/mol, making these some of the higher MW gradient copolymers reported to date. Due to the proximity of the glass transition temperatures (T_g) of polystyrene (PS) and poly(4-methylstyrene) (PMS), there is no significant difference in T_g between the gradient and random copolymers, with both copolymer types yielding single T_gs that typically increase slightly with increasing MS content. While enthalpy relaxation studies demonstrate similarity in random copolymers made by NM-CRP and ConvFRP, they reveal significant differences between random and gradient copolymers. Gradient copolymers exhibit broad enthalpy recovery peaks, whereas random copolymers exhibit narrower enthalpy recovery peaks. The maxima in the enthalpy recovery peaks are at substantially lower temperature, as much as 17 °C, in the gradient copolymers as compared to random copolymers of equal overall composition. While random and gradient copolymers of a given overall composition exhibit similar enthalpy recovery values at a common physical aging time and quench depth relative to T_g, the major differences in the enthalpy recovery peaks indicate that differences in sequence distribution along the chain length can lead to unusual behavior in gradient copolymers relative to random copolymers.     

Thermal properties and biodegradability of the copolymers of l-lactide, ?-caprolactone, and ethylene glycol oligomer with maleate units and their crosslinked products

Copolymers of l-lactide (LLA), ?-caprolactone (CL), and ethylene glycol oligomer (EGO) were synthesized by ring-opening copolymerization of CL and LLA initiated by EGO at the LLA/CL molar ratios of 7/3, 5/5, and 3/7. The resulting viscous ternary copolymers (PLCE) with weight average molecular weight (M_w) ca. 3000 were reacted with maleic anhydride to give unsaturated group-containing copolymer (PLCEM) with M_w 6000-8000. The degree of unsaturation of PLCEM was 0.3-0.6 per one EGO block. The PLCEM was cured with benzoyl peroxide (BPO) to give a viscoelastic soft material insoluble in any solvent. The DSC analysis of the copolymers revealed that all the copolymers are amorphous materials having a glass transition temperature (T_g), which increased with increasing LLA/CL ratio. The crosslinked PLCEM showed a higher T_g than the corresponding PLCE and PLCEM. The crosslinked PLCEM showed good biodegradability, when measured by a BOD method using activated sludge.     

PSA performances and viscoelastic properties of SIS‐based PSA blends with H‐DCPD tackifiers

Hotmelt pressure sensitive adhesives (PSAs) usually contain styrenic block copolymers like styrene–isoprene–styrene (SIS), SBS, SEBS, tackifier, oil, and additives. These block copolymers individually reveal no tack. Therefore, a tackifier is a low molecular weight material with high glass transition temperature (T_g), and imparts the tacky property to PSA. The SIS block copolymer with different diblocks was blended with hydrogenated dicyclopentadiene (H‐DCPD tackifier), which has three kinds of T_g. PSA performance was evaluated by probe tack, peel strength, and shear adhesion failure temperature. PSA is a viscoelastic material, so that its performance is significantly related to the viscoelastic properties of PSAs. We tested the viscoelastic properties by dynamic mechanical analysis and the thermal properties by differential scanning calorimeter to investigate the relation between viscoelastic properties and PSA performance. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 2839–2846, 2006     

Synthesis and application of styrene/4-hydroxystyrene gradient copolymers made by controlled radical polymerization: Compatibilization of immiscible polymer blends via hydrogen-bonding effects

Styrene (S)/4-hydroxystyrene (HS) copolymers are synthesized by hydrolysis of S/4-acetoxystyrene copolymer precursors; two gradient copolymer precursors are made by semi-batch, nitroxide-mediated controlled radical polymerization, and a random copolymer precursor is prepared by conventional free radical polymerization. Conventional heat curves from differential scanning calorimetry indicate two glass transition temperatures (T_gs) and a broad T_g in well-annealed 59/41 mol% and 25/75 mol% S/HS gradient copolymers, respectively, both of which contain short S end-blocks. In contrast, a narrow T_g is observed in a 57/43 mol% random copolymer. Each S/HS copolymer is added at 5 wt% by solution mixing to an 80/20 wt% polystyrene (PS)/polycaprolactone (PCL) blend and tested for its ability to compatibilize the blend during melt processing; the hydroxyl groups on the HS units can form hydrogen bonds with the PCL ester groups. The S/HS random copolymer fails as a compatibilizer while both gradient copolymers are good compatibilizers. Relative to the blend without copolymer, the blend with 59/41 mol% S/HS gradient copolymer also exhibits a major reduction in initial dispersed-phase domain size and irregularly shaped domains, which are indicators of a sharply reduced interfacial tension. In contrast, the blend with 25/75 mol% S/HS gradient copolymer has an average PCL domain size comparable to the blend without copolymer and a broad domain size distribution. The presence of S/HS copolymers in the blend leads to reduced PCL crystallization and melting temperatures as well as reduced enthalpies of crystallization and melting, consistent with some solubilization of copolymer in the PCL domain interiors.     

Thickness and composition dependence of the glass transition temperature in thin random copolymer films

Glass transition temperatures (T_g) of thin poly(styrene-co-methyl methacrylate) and poly(2-vinyl pyridine-co-styrene) films coated on a native oxide surface of Si wafer (100) were measured by ellipsometry. The thickness dependence of T_g can be properly fitted by previously suggested equation developed for homopolymers, based upon a continuous multi-layer model, although one component in thin random copolymer films demonstrates a slightly favorable interaction between a substrate and thin film, and another demonstrates a strongly favorable interaction. Surface and interface have a strong influence on T_g of thin film coated on substrate: the surface has the effect of reducing T_g, whereas the interface increases the T_g according to the degree of interaction between a substrate and thin film. This degree of interaction can be quantified as an interaction parameter (k), and is dependent on the composition of random copolymers. For the estimation of k values of thin random copolymer films, we proposed a parallel type additive function (1/k_ran=w₁/k₁+w₂/k₂) where w is a weight fraction of component.     

Comparison of thermomechanical properties of statistical, gradient and block copolymers of isobornyl acrylate and n-butyl acrylate with various acrylate homopolymers

Well-defined statistical, gradient and block copolymers consisting of isobornyl acrylate (IBA) and n-butyl acrylate (nBA) were synthesized via atom transfer radical polymerization (ATRP). To investigate structure-property correlation, copolymers were prepared with systematically varied molecular weights and compositions. Thermomechanical properties of synthesized materials were analyzed via differential scanning calorimetry (DSC), dynamic mechanical analyses (DMA) and small-angle X-ray scattering (SAXS). Glass transition temperature (T_g) of the resulting statistical poly(isobornyl acrylate-co-n-butyl acrylate) (P(IBA-co-nBA)) copolymers was tuned by changing the monomer feed. This way, it was possible to generate materials which can mimic thermal behavior of several homopolymers, such as poly(t-butyl acrylate) (PtBA), poly(methyl acrylate) (PMA), poly(ethyl acrylate) (PEA) and poly(n-propyl acrylate) (PPA). Although statistical copolymers had the same thermal properties as their homopolymer equivalents, DMA measurements revealed that they are much softer materials. While statistical copolymers showed a single T_g, block copolymers showed two T_gs and DSC thermogram for the gradient copolymer indicated a single, but very broad, glass transition. The mechanical properties of block and gradient copolymers were compared to the statistical copolymers with the same IBA/nBA composition.     

Comb-like ionomers from sustainable resources: Copolymers of itaconic anhydride-co-stearyl methacrylate

Comb-like random copolymers of itaconic anhydride (ITA) and stearyl methacrylate (SM) copolymers were synthesized by free-radical polymerization. Both monomers are derived from natural and renewable resources. Ionomers (Na, Ca or Zn carboxylates) were prepared by partial neutralization of the copolymers. The incorporation of the ionic groups decreased the melting point, which was lower than the glass transition temperature (T_g) and crystallinity of the SM side-chains and increased the T_g of the backbone by 20-25 °C. Above T_g, the parent copolymer was a viscoelastic liquid, but the introduction of the ionic groups changed the properties to that of an elastic solid due to the physical crosslinks formed by intermolecular interactions of the ionic dipoles.     

Thermal analysis,glass transition temperature and rheological behaviour of emulsion copolymers of methyl methacrylate with styrene

Poly(MMA‐ran‐St) samples were synthesized under monomer‐starved conditions (drop feeding method) by emulsion copolymerization. Their thermostability was determined by thermogravimetric analysis. The glass transition temperature (T_g) of the copolymers was determined by differential scanning calorimetry (DSC) and torsional braid analysis (TBA). The results showed that the MMA–St copolymers exhibit an asymmetric T_g versus composition curve, which could not be interpreted by Johnston's equation, taking the different contributions of the diads to the T_g of the copolymer into consideration. A new sequence distribution equation taking into account the different contributions of the triads was proposed to predict the copolymer T_g. The new equation fitted the experimental data exactly. The T_g determined by torsional braid analysis (TBA) is higher than the one determined by DSC, but the difference is not constant. The rheological behaviour of the copolymers was also studied and T_gTBA‐T_gDSC increased with the increasing flow index of the copolymer. © 2003 Society of Chemical Industry     

Synthesis, thermal properties, and specific interactions of high Tg increase in poly(2,6-dimethyl-1,4-phenylene oxide)-block-polystyrene copolymers

We have synthesized a series of block copolymers of poly(2,6-dimethyl-1,4-phenylene oxide) and polystyrene (PPO-b-PS copolymer) by atom transfer radical polymerization. The PS content in these copolymer systems was determined by using infrared spectroscopy, thermal gravimetric analysis, and solution and solid-state NMR spectroscopy; good correlations exist between these characterization methods. DSC analyses indicated that the PPO-b-PS copolymers have higher glass transition temperatures than do their corresponding PPO/PS blends. Our FTIR and solid-state NMR spectroscopic analyses suggest that the PPO-b-PS copolymers possess stronger specific interactions that are responsible for the observed relatively higher values of T_g. We found one single dynamic relaxation from the dynamic mechanical analysis, which implies dynamic homogeneity exists in the PPO-b-PS copolymer; this result is consistent with the one single proton spin-lattice relaxation time observed in the rotating frame [T_1ρ(H)] during solid state NMR spectroscopic analysis. In addition, the 2D FTIR spectroscopy reveals evidence for the stronger interactions between segments of PPO and PS through the formation of π-cation complexes.     

Phase behavior for blends of styrene containing triblock copolymers with poly(2,6-dimethyl-1,4-phenylene oxide)

The extent to which the styrene end-blocks of three commercially available triblock copolymers can mix with a particular poly(2,6-dimethyl-1,4-phenylene oxide) (M_n = 22,600 and M_w = 34,000) or PPO has been examined by investigation of the glass transition behavior of the PPO and polystyrene (PS) portions of the blends using differential scanning calorimetry. Each block copolymer has a butadiene-based mid-block which was hydrogenated for two of these materials, but not the third. The three copolymers differ substantially in overall molecular weight and in molecula weight of the blocks. However, in analogy with the literature on blends of homopolymer polystyrene with styrene-based block copolymers, the molecular weight of the PS block should be the principal factor affecting the phase behavior in the present blends. Mixtures of the PPO with the block copolymers having PS blocks with M = 14,500 (nonhydrogenated midblock) and with M = 29,000 (hydrogenated mid-block) exhibited single composition-dependent T_gs for the hard phase, indicating complete mixing of PS segments with the PPO, for all proportions. On the other hand, the block copolymer having a PS block with M = 7,500 and a hydrogenated mid-block exhibited two separate hard phase T_gs corresponding to an essentially pure PPO phase and a PS-rich phase. For blends of homopolymer PS with styrene-based block copolymers, the similar two-phase behavior of the glassy portion can be readily explained by entropic considerations. For the present case, the favorable enthalpic contribution for mixing PPO and PS is an additional factor which seems to influence the restrictions on molecular weight for complete mixing; however, additional work is needed to develop a more quantitative assessment of this new issue.     

Absorption of CO2 and subsequent viscosity reduction of an acrylonitrile copolymer

Acrylonitrile (AN) copolymers (AN content greater than about 85 mol%) are traditionally solution processed to avoid a cyclization and crosslinking reaction that takes place at temperatures where melt processing would be feasible. It is well known that carbon dioxide (CO₂) reduces the glass transition temperature (T_g) and consequently the viscosity of many glassy and some semi-crystalline thermoplastics. However, the ability of CO₂ to act as a processing aid and permit processing of thermally unstable polymers at temperatures below the onset of thermal degradation has not been explored. This study concentrates on the ability to plasticize an AN copolymer with CO₂, which may ultimately permit melt processing at reduced temperatures. To facilitate viscosity measurements and maximize the CO₂ absorption, a relatively thermally stable, commercially produced AN copolymer containing 65 mol% AN was investigated in this research. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) indicated that CO₂ significantly absorbs into and reduces the T_g of the AN copolymer. Pressurized capillary rheometry indicated that the magnitude of the viscosity reduction is dependent on the amount of absorbed CO₂, which correlates directly to the T_g reduction of the plasticized material. Up to a 60% viscosity reduction was obtained over the range of shear rates tested for the plasticized copolymer containing up to 6.7 wt% CO₂ (31 °C T_g reduction), corresponding to as much as a 30 °C equivalent reduction in processing temperature. A Williams-Landel-Ferry (WLF) analysis was used to estimate the viscosity reduction based on the T_g reduction (and corresponding amount of absorbed CO₂) in the plasticized AN copolymer, and the predicted viscosity reduction based on using the universal constants was 34-85% higher than measured, depending on the amount of absorbed CO₂. Van Krevelen's empirical solubility relationships were used to calculate the expected absorbance levels of CO₂, and found to be highly dependent on the choice of constants within the statistical ranges of error of the Van Krevelen relationships.     

Synthesis and Characterization of PVAc-b-PDMS-b-PVAc Triblock Copolymers by Atom Transfer Radical Polymerization Initiated by PDMS Macroinitiator

Poly(dimethylsiloxane) based triblock copolymer was synthesized from bis(bromoalkyl)-terminated PDMS macroinitiator (Br-PDMS-Br) and vinyl acetat telomers. Vinyl acetate telomers prepared from radical and controlled radical telomerization with Co(acac)₂/DMF catalyst and ligand, were used in atom transfer radical polymerization to synthesize Poly(vinylacetate-b-dimethylsiloxane-b-vinylcetate) triblock copolymer. The PDMS based triblock copolymers revealed a significant effect of Co(acac)₂/DMF on PVAc telomere which was used in the synthesis of highly ordered triblock copolymer on a well-defined microstructure. The results were confirmed by ¹H NMR and DSC indicating that a low T_g of PDMS in the microstructure of triblock copolymer has made the block copolymer flexible for new applications.     

Synthesis and characterization of trifluoromethyl substituted styrene polymers and copolymers with methacrylates: Effects of trifluoromethyl substituent on styrene

2-Trifluoromethyl styrene (2TFMS), 2,5-bis(trifluoromethyl) styrene (25BTFMS), and 3,5-bis(trifluoromethyl) styrene (35BTFMS) were synthesized. These styrenes were readily polymerized in bulk and also in solution using AIBN as a free radical initiator. The polymerization rate of these trifluoromethyl substituted styrenes and other monomers such as styrene (St), pentafluorostyrene (PFS) and 4-trifluoromethyl-tetrafluorostyrene (TFMTFS) were measured in benzene and dioxane by monitoring the ¹H NMR spectra of the double bond hydrogen. The order of polymerization rates was TFMTFS > 35BTFMS > 25BTFMS > PFS > 2TFMS > St. T_gs of styrene polymers with CF₃ substituted on the ortho position of the phenyl ring were much higher than those of the meta and para substituted styrenes due to the steric hindrance of the bulky CF₃ group close to the polymer main chain, which resulted in a decrease in the segment mobility of the polymer chains and an increasing T_g of the polymers. The copolymers of 2TFMS with methyl methacrylate (MMA) and also 25BTFMS with trifluoroethyl methacrylate (TFEMA) were prepared. T_gs of the copolymers were in the range of 120-145 °C and the copolymers were transparent and thermally stable. The copolymer films were flexible and exhibited high transmittance as the homopolymers of MMA and TFEMA. Thus, these copolymers may be utilized as novel optical materials.     

Fast physical drying,high water and salt resistant coatings from non-drying vegetable oil

This paper reports fast physical drying, high water and salt resistances of coating materials from non-drying palm oleic acid. Short oil-length alkyd was synthesized and copolymerized with methyl methacrylate. Three copolymers of the alkyd and methyl methacrylate with different alkyd/MMA ratios were prepared via free radical polymerization. The copolymers were characterized by FTIR and H NMR spectroscopy, and glass transition temperatures (T_g) were measured by DSC. The decreasing amount of alkyd was noticed to increasing conversion and T_g. The overall thermal stability has increased with higher amount of alkyd in the copolymer. Moreover, incorporation of alkyd has improved the adhesion and film hardness of the coatings.     

Comparison of hydrogen bonding interaction between PMMA/PMAA blends and PMMA-co-PMAA copolymers

A series of miscible PMMA/PMAA blends and PMMA-co-PMAA copolymers with different compositions were prepared in this study. T_gs of PMMA-co-PMAA copolymers are significantly higher than average values or from the Fox equation. The proton spin-lattice relaxation time in the rotating frame (T_1ρ^H) determined by high resolution solid state ¹³C nuclear magnetic resonance indicates single composition-dependent from all blends and copolymers, implying a good miscibility with chain dynamics on a scale of 1-2 nm. However, T_1ρ^Hs of copolymers are still smaller than those of blends, implying that degrees of homogeneity of copolymers are higher than those of blends. On the basis of Kovacs' free volume theory, the free volume of the copolymer obtained is decreased which is another indication of greater homogeneity of the copolymer than that of the corresponding blend. According to Fourier transform infrared spectroscopy analyses, the above results can be rationalized that the hydrogen bonding interaction of the copolymer is stronger than the blend.     

Design and synthesis of zero–zero-birefringence polymers in a quaternary copolymerization system

We designed and synthesized quaternary copolymers of methyl methacrylate (MMA), 2,2,2-trifluoroethyl methacrylate (TFEMA), benzyl methacrylate (BzMA), and 3,3,5-trimethylcyclohexyl methacrylate (TMCHMA) and we investigated their birefringence, thermal properties, and other optical properties. When the copolymer composition was MMA/TFEMA/BzMA/TMCHMA = 50:38:8:4, 40:30:7:23, or 30:21:7:42 (wt%), a zero–zero-birefringence polymer that exhibited neither orientational nor photoelastic birefringence was obtained. We demonstrated that such zero–zero-birefringence polymers with a variety of compositions could be successfully prepared in the quaternary system by using the same compensation method as applied in ternary random copolymerization. We also demonstrated that the glass-transition temperature (T_g) and refractive index (n_D) of these copolymers could be controlled with high accuracy while retaining their zero–zero-birefringence property. We can therefore predict the type of birefringence, the T_g, and the n_D of a particular copolymer before polymerization. Zero–zero-birefringence polymers with the most appropriate characteristics can then be synthesized selectively by quaternary copolymerization.     

Influence of cross-link density on the properties of ROMP thermosets

A norbornene-based cross-linker was synthesized and mixed at different loadings with two separate monomers for self-healing polymer applications: 5-ethylidene-2-norbornene (ENB) and endo-dicyclopentadiene (endo-DCPD). The monomer/cross-linker systems were polymerized by ring-opening metathesis polymerization (ROMP) with Grubbs' catalyst. The thermal-mechanical properties of the polymerized networks were evaluated by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) and the curing process was monitored by parallel plate oscillatory rheometry. The viscosities of the pre-polymer blends are shown to be adequately low for self-healing, and exhibit a high ROMP reactivity to form cross-linked networks with enhanced thermal-mechanical properties. The addition of cross-linker increases the glass transition temperature (T_g) and the storage modulus both above and below T_g. The storage modulus increase above T_g is used to estimate the molecular weight (M_c) between entanglements or cross-link sites for both ENB and endo-DCPD-based networks. The cross-linker also greatly accelerates network formation as defined by the gelation time.     

Metal ion interaction of water‐soluble copolymers containing carboxylic acid groups in aqueous phase by membrane filtration technique

This article reports the synthesis of poly(N‐maleoylglycine‐co‐itaconic acid) by radical copolymerization under different feed mole ratios and its properties to remove various metal ions, such as Cu(II), Cr(III), Co(II), Zn(II), Ni(II), Pb(II), Cd(II), and Fe(III), in aqueous phase with the liquid‐phase polymer‐based retention(LPR) technique. The interactions of inorganic ions with the hydrophilic water‐soluble polymer were determined as a function of pH and filtration factor. Metal ion retention was found to strongly depend on the pH. Metal ion retention increased as pH and MG content units in the macromolecular backbone increased. The copolymers were characterized by elemental analysis, FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopy. Additionally, intrinsic viscosity, molecular weight, and polydispersity have been determined for the copolymers. Copolymer and polymer–metal complex thermal behavior was studied using differential scanning calorimetry (DSC) and thermogravimetry (TG) techniques under nitrogen atmosphere. The thermal decomposition temperatures (TDT) were influenced by the copolymer composition. The copolymers present lower TDT than the polymer–metal complex with the same copolymer composition. All copolymers present a single T_g, indicating the formation of random copolymers. A slight deviation of the T_g for the copolymers and its complexes can be observed. The copolymer T_g is higher than the T_g value for the polymer–metal complexes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Glass‐transition temperatures and rheological behavior of methyl methacrylate–styrene random copolymers

Poly(methyl methacrylate‐ran‐styrene) copolymers were synthesized under monomer‐starved conditions by emulsion copolymerization. The glass‐transition temperatures (T_g's) of the copolymers were measured by differential scanning calorimetry (DSC) and torsional braid analysis (TBA). The results showed that the methyl methacrylate–styrene random copolymers produced an asymmetric T_g versus composition curve, which could not even be interpreted by the Johnston equation with different contributions of dyads to the T_g of the copolymer considered. A new sequence distribution equation concerning different contributions of triads was introduced to predict the copolymer's T_g. The new equation fit the experimental data exactly. Also, the T_g determined by TBA (T_gTBA) was higher than the one determined by DSC (T_gDSC) and the difference was not constant. The rheological behavior of the copolymers was also studied. T_gTBA ? T_gDSC increased with increasing flow index of the melt of the copolymer, and the reason was interpreted. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2891–2896, 2003     

Synthesis and properties of ethylene‐substituted styrene copolymers

The copolymerization of ethylene and substituted styrenes [RSt's; p‐methylstyrene (MSt), p‐tert‐butylstyrene (BSt), 2‐vinylnaphthalene (VN), and p‐(tert‐butyldimethylsilyloxy)styrene (BMSiOSt)] were investigated with dimethylsilylene(tetramethylcyclopentadienyl)(N‐tert‐butyl)titanium dichloride to yield the corresponding ethylene–RSt copolymers. The substituent on the styrene (St) monomers did not affect the monomer reactivity ratio. The effect of the substituent structure of RSt on the thermal and mechanical properties was studied with differential scanning calorimetry, dynamic mechanical thermal spectroscopy, and elongation testing. The glass‐transition temperature (T_g) of the copolymers increased with increasing RSt content, and the order of T_g was as follows: BSt > VN > MSt = St. A copolymer with p‐hydroxystyrene (HOSt) was successively synthesized by means of deprotection of the copolymer with BMSiOSt. The copolymer showed a much higher T_g than the other copolymers because of the hydrogen connection of its OH groups. The mechanical properties of the copolymer in the glass state, at a lower temperature than T_g, were almost independent of the nature of the RSt. The substituent of the St monomers affected the pattern of the stress–strain curve in the elongation testing in the amorphous state. An improvement in the shape memory effect was observed in poly(ethylene‐co‐BSt). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008