Synergistic effects of carbon fillers on tensile and flexural properties in liquid‐crystal polymer based resins

One emerging market for thermally and electrically conductive resins is bipolar plates for use in fuel cells. Adding carbon fillers to thermoplastic resins increases the composite thermal and electrical conductivity. These fillers have an effect on the composite tensile and flexural properties, which are also important for bipolar plates. In this study, various amounts of three different types of carbon (carbon black, synthetic graphite particles, and carbon fibers) were added to Vectra A950RX liquid‐crystal polymer. In addition, composites containing combinations of fillers were also investigated via a factorial design. The tensile and flexural properties of the resulting composites were then measured. The objective of this study was to determine the effects and interactions of each filler with respect to the tensile and flexural properties. The addition of carbon black caused the tensile and flexural properties to decrease. Adding synthetic graphite particles caused the tensile and flexural modulus to increase. The addition of carbon fiber caused the tensile and flexural modulus and ultimate flexural strength to increase. In many cases, combining two different fillers caused a statistically significant effect on composite tensile and flexural properties at the 95% confidence level. For example, when 40 wt % synthetic graphite particles and 4 wt % carbon black were combined, the composite ultimate tensile and flexural strength increased more than what would be expected from the individual additive effect of each single filler. It is possible that linkages were formed between the carbon black and synthetic graphite particles that resulted in improved ultimate tensile and flexural strength. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Aramid nanofiber reinforced nitrile rubber assisted by cellulose nanocrystals

A fiber-reinforced rubber composite was prepared by mixing aramid nanofibers (ANF) suspension and nitrile rubber (NBR) latex. The effects of ANF content and corresponding surface modification on the microstructure, vulcanization performance, processing and mechanical properties of composite materials, were systematically investigated. We found that, compared with commonly used short-cut aramid fibers, ANF fillers tend to form a stronger filling network within NBR matrix, resulting in a pronounced Payne effect. By improving the interfacial adhesion via dopamine (DA) coating onto ANF surface, the tensile strength can be further enhanced as expected. Besides, to eliminate the detriment of mechanical performance due to residual sodium polyacrylate in the course of flocculation, cellulose nanocrystal (CNC) was adopted to serve as a thickener during solution mixing. The incorporation of CNC can significantly improve the mechanical properties, which identifies a synergistic reinforcement effect arising from the cooperation of two types of fillers.     

Tensile properties of carbon filled liquid crystal polymer composites

Electrically and thermally conductive resins can be produced by adding carbon fillers. Mechanical properties such as tensile modulus, ultimate tensile strength, and strain at ultimate tensile strength are vital to the composite performance in fuel cell bipolar plate applications. This research focused on performing compounding runs followed by injection molding and tensile testing of carbon filled Vectra A950RX liquid crystal polymer composites. The four carbon fillers investigated included an electrically conductive carbon black, thermocarb synthetic graphite particles, and two carbon fibers (Fortafil 243 and Panex 30). For each different filler type, resins were produced and tested that contained varying amounts of these single carbon fillers. The carbon fiber samples exhibited superior tensile properties, with a large increase in tensile modulus over the base polymer, and very low drop in the ultimate tensile strength as the filler volume fraction was increased. The strain at the ultimate tensile strength was least affected by the addition of the Panex carbon fiber but was significantly affected by the Fortafil carbon fiber. In general, composites containing synthetic graphite did not perform as well as carbon fiber composites. Carbon black composites exhibited poor tensile properties. POLYM. COMPOS., 29:15–21, 2008. © 2007 Society of Plastics Engineers     

Aramid pulp reinforced hydrogenated nitrile butadiene rubber composites with ionic liquid compatibilizers

Although carbon black is an effective reinforcement for most rubbers, its replacement by other fillers would be beneficial. Aramid fibers are used in a range of applications in the rubber industry, providing dimensional stability prior to vulcanization and improving the mechanical properties of the elastomeric product. Nevertheless, their relatively inert surface is an obstacle in the exploitation of their full potential. In this work, two ionic liquids were investigated as compatibilizers in the preparation of hydrogenated nitrile butadiene rubber composites with aramid pulp and carbon black fillers. The materials were characterized using swelling, hardness and tensile tests, differential scanning calorimetry, thermal gravimetric analysis, and infrared spectroscopy. The carbon black-free composite prepared from aramid pulp treated with 1.0 wt% of 1-carboxymethyl-3-methylimidazolium chloride outperformed all other studied materials, presenting a higher modulus at 100% strain (7.31 MPa), while maintaining high strain at break. Thus, ionic liquids were found to potentialize the aramid reinforcement effect in these rubber composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48702.     

Investigation of 3D printing strategy on the mechanical performance of coextruded continuous carbon fiber reinforced PETG

Fused filament fabrication (FFF) has been used to create prototypes and functional parts for various applications using plastic filaments. It has also been extended to the use of continuous fibers for reinforcing thermoplastic polymers. This study aims to optimize the deposition design of a coextruded continuous carbon fiber (CCF) composite filament with a polyethylene terephthalate glycol-modified (PETG) filament. The characterizations on the raw materials revealed that the matrix polymer in CCF composite filament had similar physicochemical properties as PETG, and carbon fibers were homogeneously distributed in CCF filament. The effect of raster orientation and shells number on the mechanical properties of non-reinforced and coextruded CCF-reinforced PETG was investigated. The highest mechanical properties were obtained at a raster orientation of 0° for both reinforced and non-reinforced materials. With the increase of raster orientation, Young's modulus and ultimate tensile strength decreased. The presence of shells improved the tensile strength of non-reinforced PETG. For composite samples printed with unreinforced shells, Young's modulus decreased due to decrease in fibers content, and elongation at break and ultimate tensile strength increased. Tomographic observations showed that the mechanical behavior of printed specimens depended on the anisotropy of porosity in printed specimens.     

Effect of strain on the properties of an ethylene–octene elastomer with conductive carbon fillers

Composites that incorporate a conductive filler into an ethylene–octene (EO) elastomer matrix were evaluated for DC electrical and mechanical properties. Comparing three types of fillers (carbon fiber, low structure carbon black, and high structure carbon black), it was found that the composite with high structure carbon black exhibited a combination of properties not generally achievable with this type of filler in an elastomeric matrix. A decrease in resistivity at low strains is unusual and has only been reported previously in a few instances. Reversibility in the resistivity upon cyclic deformation is a particularly unusual feature of EO with high structure carbon black. The mechanical and electrical performance of the high structure carbon black composites at high strains was also impressive. Mechanical reinforcement in accordance with the Guth model attested to good particle–matrix adhesion. The EO matrix also produced composites that retained the inherent high elongation of the unfilled elastomer even with the maximum amount of filler (30% by volume). The EO matrix with other conducting fillers did not exhibit the exceptional properties of EO with high structure carbon black. Composites with carbon fiber and low structure carbon black did not maintain good mechanical properties, generally exhibited an increase in resistivity with strain, and exhibited irreversible changes in both mechanical and electrical properties after extension to even low strains. An explanation of the unusual properties of EO with high structure carbon black required unique features of both filler and the matrix. The proposed model incorporates the multifunctional physical crosslinks of the EO matrix and dynamic filler–matrix bonds. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 894–905, 2000     

Epoxy Resin Composite Reinforced with Carbon Fiber and Inorganic Filler: Overview on Preparation and Properties

Among carbon fillers, carbon fiber is considered to be an ideal reinforcement for epoxy because of its outstanding electrical, mechanical, and thermal features. Several inorganic fillers such as zinc oxide, titania, and silica are also used in epoxy matrix for property enhancement. The review initially focuses the preparation methods and physical characteristics of epoxy/carbon fiber composite. Afterward, fabrication and properties of epoxy/zinc oxide/titania/silica composites are also conversed. Moreover, the effect of filler dispersion on polymer properties’ improvement is also highlighted. Epoxy/carbon fiber composites are employed more frequently and effectively in defense-related applications compared with epoxy/inorganic nanofiller composite.     

New nanocomposite materials made of an insulating matrix and conducting fillers: Processing and properties

The work described in this paper deals with the preparation and the characterization of an homogeneous composite material composed of electrically conductive fillers dispersed in a thermoplastic insulating matrix. These fillers were chosen to have either a spherical shape or a high aspect ratio. Processing of these conductive polypyrrole particles, which were obtained either through a classical polymerization of pyrrole in the presence of stabilizer, or polymerization onto the surface of cellulose monocrystals is detailed. The relationship of filler content in the composite to electrical and mechanical properties was investigated. In order to characterize the connectivity of the fillers in the matrix, electrical measurements were performed and these results have been compared with the predictions of the statistical percolation theory. Further analysis was undertaken by considering the influence of the network of rigid particles on the viscoelastic properties of the composites. These results were compared with two models; first, with a mechanical percolation approach which was based on strong interactions between fillers, and second, with a mean field model, which in no way accounted for interactions bewteen fillers. In recent developments, it has been shown that these materials used as coating on various substrate could be good sensors, allowing to determine some specific features of the substrate deformation.     

Effects of silanization of C/C composites and grafting of h-BN fillers on the microstructure and interfacial properties of CVI-based C/C-BN composites

A low-density carbon/carbon (C/C) composite/silane coupling agent/hexagonal boron nitride (h-BN) hybrid reinforcement was prepared by grafting polyethyleneimine (PEI)-encapsulated modified h-BN fillers onto a carbon fiber surface using 3-aminopropyltriethoxysilane (APS) as the connection to improve the distribution uniformity of h-BN fillers in quasi-three-dimensional reinforcements and the interfacial properties between the fibers/pyrocarbon (PyC) in the C/C-BN composites obtained after densification by chemical vapor infiltration (CVI). The microstructure and chemical components of the hybrid reinforcement were investigated. The transmission electron microscopy (TEM) sample was prepared using a focused-ion beam (FIB) for the h-BN/PyC interfacial zone. The interlaminar shear strength (ILSS) and impact toughness were analyzed to inspect the composites’ interfacial properties. The results show that APS and h-BN are uniformly grafted on the fiber surface in the chopped fiber web inside the C/C composite without a density gradient, and agglomeration occurred and significantly increasing the fiber surface roughness. The highly ordered h-BN basal plane may affect the order degree of PyC near the h-BN/PyC interface. The addition of h-BN reduces the PyC texture near it, causing the annular cracks to disappear gradually. The lower PyC texture and the rougher fiber surface strengthen the interfacial bond of the fiber/matrix. Consequently, the ILSS strength of the C/C-BN composites first increases and then decreases as the h-BN filler content increases and is always higher than that of the C/C composite, while the addition of h-BN fillers weakens its impact toughness. When the h-BN content in the C/C-BN composite is 10 vol%, the ILSS of the C/C-BN composites was 15.6% higher than that of the C/C composites. However, when the h-BN content is excessive (15 vol%), the densely grafted h-BN will bridge each other, reducing the subsequent CVI densification efficiency to form a loose interface, causing a decrease in the shear strength.     

Torrefied agro-industrial residue as filler in natural rubber compounds

This study explored the feasibility of using torrefied biomass as a reinforcing filler in natural rubber compounds. Carbon black was then replaced with the torrefied biomass in elastomer formulations for concentrations varying from 0% to 100% (60 parts per hundred rubber or phr total). Their influence on the curing process, dynamic properties, and mechanical properties was investigated. Results were compared with the properties of vulcanizates containing solely carbon black fillers. Time to cure (t₉₀) for compounds with torrefied biomass fillers increased, while filler-filler interactions (ΔG') decreased, compared to carbon black controls. At low strains, the tan δ values of the torrefied fillers vulcanizates were similar to the controls. Incorporation of torrefied biomass into natural rubber decreased compound tensile strength and modulus but increased elongation. Replacement with torrefied fillers resulted in a weaker filler network in the matrix. Still, results showed that moderate substitution concentrations (~20 phr) could be feasible for some natural rubber applications.     

Excavating the unique synergism of nanofibers and carbon black in Natural rubber based tire tread composition

The article portrays the synergistic reinforcement of new generation nanofillers such as silicon carbide nanofibers (SiCs), carbon nanotubes (CNTs), and graphite nanofibers (GNFs) when used along with carbon black (CB) in a typical tire tread composition. The unique synergism in these composites, which were fabricated by a liquid phase mixing method, was reflected in their enhanced failure resistance and dynamic mechanical properties. At 4 phr loading of the nanofiber, the tensile strength, tear strength, modulus at 300% elongation, storage modulus, rolling resistance, and abrasion resistance were improved by 29, 45, 36, 110, 15, and 14%, respectively. The role of nanofibers in the development of a hybrid microstructure was investigated by scanning and transmission electron microscopy. Tribological characteristics were studied using a Laboratory Abrasion Tester (LAT 100), and the abrasion loss of the samples was correlated with energy dissipation occurring during the process. The fatigue properties indicated the ability of the CB-nanofiber dual filler system to arrest crack growth. The study also serves to establish a correlation between the wear loss and fatigue properties of the hybrid nanocomposites containing different fibrous nanofillers. A mechanism of reinforcement by hybrid fillers is proposed.     

Thermoplastic polyurethane composites reinforced with renewable and sustainable fillers – a review

ABSTRACT

Thermoplastic polyurethane (TPU) reinforced with natural or renewable fillers gained significant attention in the scientific community and industries. The properties of TPU can be tailored using different reinforcements or blends to enhance its performance and elevate the potential applications of the composite. Besides, composites offer eco-friendliness, recyclability, and biocompatibility thus overcoming the environmental concerns. However, the manufacturing in mass quantity and upholding the quality of these composites has remained one of the principal challenges. Herein, we critically highlighted an overview of the current comprehension of the various eco-friendly and renewable fillers/fibers reinforced in TPU composites for tuning the mechanical and thermal properties of TPU. Some of the important research articles that discuss the influence of interactions, morphology, and modification/treatment of fillers are contained within to understand the behavior and consequence of reinforcements on the physical properties of TPU composites.     

Effect of different types of filler and filler loadings on the properties of carboxylated acrylonitrile–butadiene rubber latex films

The effects of different types of fillers and filler loadings on the properties of carboxylated nitrile rubber (XNBR) latex were identified. Silica, mica, carbon black (CB; N330), and calcium carbonate (CaCO₃) were used as fillers with filler loadings of 10, 15, and 20 parts per hundred rubber. Furnace ashing and Fourier transform infrared analysis proved that interaction existed between the fillers and XNBR latex films. The morphology of the filled XNBR films was significantly different for different types of fillers. Mica and CaCO₃ fillers showed uneven distribution within the XNBR film, whereas other fillers, such as silica and CB, showed homogeneous distribution within the films. In the observation, silica and mica fillers also illustrated some degree of agglomeration. The mechanical properties (e.g., tensile and tear strengths) showed different trends with different types of fillers used. For silica and mica fillers, the mechanical properties increased with filler loadings up to a certain loading, and decreased with higher filler loadings. For CB filler, the mechanical properties increased gradually with increasing filler loadings. CaCO₃ fillers did not increase the mechanical properties. The crosslinking density of the XNBR films increased when they were incorporated with fillers because of the presence of elastomer–filler and filler–filler interactions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of filler geometry on viscoelastic damping of graphite/aramid and carbon short fiber‐filled SBR composites: A new insight

An investigation on the effect of filler geometry/shape on the dynamic mechanical properties of polymers was conducted. The viscoelastic damping matrix chosen was SBR and the fillers chosen were graphite, aramid, and carbon short fibers. The study was conducted by taking a control base compound of 20 parts N330 carbon black‐filled styrene butadiene rubber (SBR). Dynamic mechanical thermal analyzer was used to investigate the viscoelastic damping of the rubber composites at low dynamic strain levels. Compressive hysterisis at moderate degree of strain were evaluated for all the composite samples to probe into their high strain static damping properties. SEM was used to investigate the matrix‐fiber interaction and distribution of the fillers. Investigations demonstrated that the matrix‐filler interface plays a major role in energy dissipation. The amount of interface was analyzed by considering the half height width of tan δ peak. Fiber matrix interaction parameter was calculated from the tan δ_max values for matrix and composite. It was observed the interaction parameter and the low strain tensile stress values register similar trend. Aramid short fibers were most effective in more energy dissipation than other fillers under consideration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of carbon‐based nanoparticles on the cure characteristics and network structure of styrene–butadiene rubber vulcanizate

The network structure of styrene–butadiene rubber (SBR) in the presence of carbon black (CB) with two different structures and multi‐walled carbon nanotubes (MWCNTs) was investigated. Swelling behaviour, tensile properties at various strain rates and cure kinetics were characterized. Experimental data were analysed using the Flory–Rehner model as well as the tube model theory. It is found that the network structure of CB‐filled SBR follows a three‐phase composite model including rigid particles, semi‐rigid bound rubber and matrix rubber. This bound rubber is postulated to be critical for the mechanical and deformational properties, development of crosslinking density in matrix rubber and polymer–filler interaction. For MWCNT‐filled SBR, the bound rubber does not show a substantial contribution to the network structure and mechanical performance, and these properties are greatly dominated by the higher aspect ratio and polymer–filler interaction. Additionally it is deduced that the crosslinking density of matrix rubber increases on incorporation of the fillers compared to unfilled matrix rubber. Copyright © 2012 Society of Chemical Industry     

Hybridization effect of cellulose paper and postcuring conditions on the mechanical properties of flax fiber reinforced epoxy biocomposite

An ever-increasing rise in demand for sustainable materials has received significant attention in developing biocomposites for structural applications. In this regard, natural fibers replacing synthetic fibers as reinforcement in epoxy composite could be a significant gain toward sustainability, especially in automobile and structural applications. Herein, flax fiber/cellulose paper–reinforced epoxy biocomposite (FREC-X) was fabricated via a vacuum infusion process. The influence of postcuring conditions (time and temperature) and cellulose paper density on the mechanical properties of FREC-X was studied. The tensile strength and modulus of FREC-X increased by 37% and 64%, respectively, upon the integration of paper. Postcuring FREC-X further augmented the tensile and flexural properties of the composite, which could be attributed to the increase in cross-linking of the epoxy and yields a strong polymer network. Fractography analysis confirmed that the composites integrated with paper showed fewer defects with improved interfacial adhesion. In addition, the water absorption and thickness swelling results revealed that the presence of cellulose paper marginally increased the water uptake and thickness swelling of FREC-X. Furthermore, there was no significant change in the tensile and flexural properties of FREC-X observed even after immersing in water for >200 h. Such properties of FREC-X seen as a fascinating alternative to synthetic fibers and petroleum-based epoxy and are promising material for sustainable development.     

Synergistic effects of carbon fillers on tensile and impact properties in nylon 6,6 and polycarbonate based resins

Electrically and thermally conductive resins can be produced by adding conductive fillers to insulating polymers. Mechanical properties such as tensile modulus, ultimate tensile strength, strain at ultimate tensile strength, and notched Izod impact strength are also important and cannot be ignored. This research focused on performing compounding runs followed by injection molding and tensile and impact property testing of carbon filled nylon 6,6 and polycarbonate based resins. The three carbon fillers investigated included an electrically conductive carbon black, synthetic graphite particles, and a milled pitch based carbon fiber. For each polymer, resins were produced and tested that contained varying amounts of these single carbon fillers. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate in each polymer. The objective of this paper was to determine the effects and interactions of each filler on the tensile and impact properties. The results showed that, in many cases, combining two and three different fillers caused a statistically significant effect at the 95% confidence level. Polym. Compos. 25:172–185, 2004. © 2004 Society of Plastics Engineers.     

Effects of carbon fillers on tensile and flexural properties in polypropylene‐based resins

A potential application for conductive resins is in bipolar plates for use in fuel cells. The addition of carbon filler can increase the electrical and thermal conductivities of the polymer matrix but will also have an effect on the tensile and flexural properties, important for bipolar plates. In this research, three different types of carbon (carbon black, synthetic graphite, and carbon nanotubes) were added to polypropylene and the effects of these single fillers on the flexural and tensile properties were measured. All three carbon fillers caused an increase in the tensile and flexural modulus of the composite. The ultimate tensile and flexural strengths decreased with the addition of carbon black and synthetic graphite, but increased for carbon nanotubes/polypropylene composites due to the difference in the aspect ratio of this filler compared to carbon black and synthetic graphite. Finally, it was found that the Nielsen model gave the best prediction of the tensile modulus for the polypropylene based composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Tensile and impact properties of carbon filled nylon‐6,6 based resins

Electrically and thermally conductive resins can be produced by adding conductive fillers to insulating polymers. Mechanical properties such as tensile modulus, ultimate tensile stress, strain at ultimate tensile stress, and notched Izod impact strength are also important and cannot be ignored. This study focused on performing compounding runs, followed by injection molding and evaluation of tensile and impact properties of carbon filled nylon‐6,6 based resins. The three carbon fillers investigated include an electrically conductive carbon black, synthetic graphite particles, and a surface treated polyacrylonitrile (PAN) based carbon fiber. Resins containing varying amounts of these single carbon fillers were produced and tested. In addition, combinations of fillers were investigated by conducting a full 2³ factorial design and a complete replicate. The addition of carbon fiber increased the composite tensile modulus, ultimate tensile stress, and impact strength. Also, in many cases, combining two or three different fillers caused a statistically significant effect at a 95% confidence level. When comparing the results of this study with prior work, it appears that increased heteroatoms present on the carbon fiber surface likely improve composite ultimate tensile stress and impact strength. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2881–2893, 2004     

Mechanical properties of 3D parts fabricated by fused deposition modeling: Effect of various fillers in polylactide

Weak mechanical strength and serious mechanical anisotropy are two key limiting factors for three-dimensional (3D) parts prepared by fused deposition modeling (FDM) in industrial applications. In this work, we investigated the relationships between mechanical properties and surface quality of FDM parts with the properties of materials used. Three kinds of polylactide (PLA) filaments, composed of the same PLA matrix but different fillers (carbon fibers and talc), were used to prepare FDM specimens. Due to the nature of FDM process, FDM parts exhibited tensile properties weaker and more anisotropic than their injection-molding counterparts. The presence of fillers affected the tensile properties of FDM parts, especially the degree of mechanical anisotropy. It is found that the interlayer bond governing the mechanical performance of FDM parts was improved since the fillers added in the polymer materials facilitates the molecular diffusion across the bond interface. Also, the surface quality of FDM parts varied with fillers. Neat PLA parts exhibited surface quality superior to the 3D parts printed with composites filaments. This work is believed to provide highlights on the development of polymer composites filament and improvement of mechanical properties of FDM parts. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47824.