Synthesis of a pyridine substituted polycarbodiimide and its use as a solid support for chemical reagents

Optically active, polycarbodiimides 3(a, b & c) with pyridine pendant groups were synthesized using [(R) - 2,2′- binaphthoxy] (di-isopropoxy) titanium(IV) catalyst. The polymers were characterized by ¹H and ¹³C NMR, and IR. Thermal stability of these polymers (up to 162 °C by TGA), allows thermally demanding chemical transformations on their side chains without decomposition. Advantages include fine-tunability of the other pendant group of the carbodiimide monomer. This allows one to optimize the properties of the polymer without undergoing copolymerization or further post-polymerization modifications. Borane (BH₃) was coordinated to poly 3 (a & b) to prepare the functional polymers 4 (a & b) respectively. A strong IR signature peak at 2368 cm⁻¹ supports BH₃ coordination. Gravimetric analysis indicates 97-99% borane complexation of the pyridine units. In addition, the thermal stability increased to 194 °C in poly 4a is consistent with the incorporation of BH₃ to the pendant pyridine of the helical polycarbodiimide 3a. Poly 4 (a & b) can be used as supported reagents and successfully reduced the carbonyl compounds (5 a-e) in moderate to excellent yields (60-100%) and are shown to be efficient, non-volatile, stable, and mild supported-reducing reagents. Upon completion of the reduction reaction, the polymer support was quantitatively recycled as required for a green solid catalyst support.     

Synthesis and properties of polynorbornenes bearing oligomeric siloxane pendant groups

The ring-opening metathesis polymerization (ROMP) of norbornene derivatives 1-5 bearing oligomeric siloxane pendant groups was carried out with Grubbs 1st and 2nd generation, and Grubbs-Hoveyda ruthenium (Ru) catalysts. Monomer 1 gave high-molecular-weight polymers (M_n ca. 27?000-180?000) in high yields (80-100%). Monomers 2-5 also polymerized with Ru carbene catalysts to give high-molecular-weight polymers (M_n ca. 34?000-240?000) in high yields (66-100%). The onset temperatures of weight loss (T₀) of the polymers were 180-250 °C. The glass transition temperatures (T_gs) of poly(1) and poly(2) bearing branched siloxane linkages were near or higher than room temperature (27 and 101 °C). Meanwhile, the T_gs of poly(3)-poly(5) bearing linear siloxane linkages were much lower (−115 to −23 °C), and decreased with increasing length of the siloxane linkages. Poly(1) and poly(2) were hydrogenated completely, which was confirmed by ¹H NMR spectroscopy. The free-standing membranes of poly(1) and poly(2) showed high gas permeability; especially poly(2) is the most permeable to various gases among ROMP-polynorbornene derivatives reported so far.     

Synthesis and properties of helical polyacetylenes containing carbazole

Novel acetylene monomers containing carbazole with chiral menthyl and bornyl groups, 9-(1R,2S,5R)-menthyloxycarbonyl-2-ethynylcarbazole (1), 9-(1S,2R,5S)-menthyloxycarbonyl-2-ethynylcarbazole (2), 9-(1R,2S,5R)-menthyloxycarbonyl-3-ethynylcarbazole (3) and 9-(1S)-bornyloxycarbonyl-2-ethynylcarbazole (4) were synthesized and polymerized with a Rh catalyst to give the corresponding polymers [poly(1)-poly(4)] with moderate M_n value of (11.5-92.2) × 10³ in good yields (77-89%). CD spectroscopic studies revealed that poly(1), poly(2) and poly(4) took predominantly one-handed helical structure in CHCl₃, THF, toluene, and CH₂Cl₂, while poly(3) did not. Addition of methanol to CHCl₃ solutions of poly(1) and poly(2) resulted in the formation of aggregates showing smaller CD signals at 275 and 320 nm. The helical structure of poly(1) and poly(2) was very stable against heating. The polymers emitted fluorescence in 0.40-2.90% quantum yields. Poly(4) exhibited an obvious oxidation peak at 1.10 V. The polymers were thermally stable below 300 °C.     

Polybinaphthyls incorporating chiral 2,2′-binaphthyl and isoquinoline moieties by Sonogashira reaction

Polymers P-1, P-2, P-3, P-4 and P-5 were synthesized by the polymerization of 5,8-bis(ethynyl)isoquinoline (M-1) with (R)-3,3′-diiodo-2,2′-bisbutoxy-1,1′-binaphthyl ((R)-M-2), (S)-3,3′-diiodo-2,2′-bisbutoxy-1,1′-binaphthyl ((S)-M-2), (R)-6,6′-dibromo-2,2′-bisbutoxy-1,1′-binaphthyl ((R)-M-3), (S)-6,6′-dibromo-2,2′-bisbutoxy-1,1′-binaphthyl ((S)-M-3), and rac-6,6′-dibromo-2,2′-bisbutoxy-1,1′-binaphthyl (M-4) under Sonogashira reaction, respectively. Both monomers and polymers were analyzed by NMR, MS, FT-IR, UV-vis spectroscopy, DSC-TGA, fluorescence spectroscopy, GPC and circular dichroism (CD) spectroscopy. CD spectra of polymers P-1 and P-2, P-3 and P-4 are almost identical except that they gave opposite signals at each wavelength. The long wavelength CD effect of P-1 and P-2 can be regarded as the more extended conjugated structure in the repeating unit and the helical backbone in the polymer chain. All five polymers have strong blue-green fluorescence due to the efficient energy migration from the extended π-electronic structure of the repeating unit of the polymers to the chiral binaphthyl core and are expected to provide understanding of structure-property relationships of the chiral conjugated polymers.     

Anionic polymerization of 2-haloethyl methacrylates

The anionic polymerizations of 2-chloroethyl methacrylate (1), 2-bromoethyl methacrylate (2), and 2-iodoethyl methacrylate (3) were carried out in THF at −78 °C with 1,1-diphenyl-3-methylpentyllithium in the presence of LiCl. The polymerizations proceeded in a controlled manner to quantitatively afford polymers with predictable molecular weights and narrow molecular weight distributions. Under similar conditions, the anionic block copolymerizations by the sequential addition of methyl methacrylate (MMA) followed by 1, 2, and 3 generated the corresponding diblock copolymers with well-defined structures. On the other hand, in the block copolymerization by the reverse addition of monomer, a well-defined diblock copolymer, poly(1)-block-PMMA, could be synthesized only by the sequential addition of 1 followed by MMA, whereas the block copolymerizations using 2 and 3 were not successful because of instabilities of the propagating chain-end anions derived from 2 and 3. The side reactions which occurred during the polymerization were discussed.     

Synthesis, characterization, and properties of novel phenylene-silazane-acetylene polymers

New phenylene-silazane-acetylene polymers, P1 and P2, have been synthesized using Sonogashira cross-coupling reactions with a new designed ethynyl-ended silylenediamine, N,N′-bis(4-ethynylphenyl)-1,1-diphenylsilylenediamine (1), as the key monomer. This also represents the first example that construction of polymers containing silazane unit with Sonogashira coupling reaction. The structures of monomer and polymers were well characterized. Their thermal properties were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Both polymers had good thermal stability with their temperatures at 5% weight loss (T_d5) being higher than 394 °C under nitrogen and higher than 385 °C in air, respectively. Their char yields at 1000 °C under N₂ were above 70%. The fundamental photophysical properties in solution were also investigated. Both polymers showed fluorescence in ultraviolet region with moderate quantum yields. These polymers had potential to be used as high-temperature resistant resins and light-emitting materials with good thermal stability.     

Synthesis and electro-optical properties of helical polyacetylenes carrying carbazole and triphenylamine moieties

Novel chiral acetylene monomers bearing carbazole and triphenylamine groups, namely, (S)-3-butyn-2-yl 2-(9-carbazolyl)ethyl carbonate (1) and (S)-3-butyn-2-yl 4-(diphenylamino)benzoate (2) were synthesized, and polymerized with Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃] catalyst to give the corresponding polymers with moderate molecular weights (M_n 13.0 × 10³ and 15.5 × 10³) in good yields (86% and 88%). CD spectroscopic studies revealed that poly(1) and poly(2) took predominantly one-handed helical structure in CHCl₃. The helical structures of poly(1) and poly(2) were very stable against heating and addition of MeOH. The solution of poly(1) and poly(2) emitted fluorescence in 0.52% and 7.2% quantum yields, which were lower than those of the corresponding monomers 1 and 2 (22.5% and 76.5%). The cyclic voltammograms of the polymers indicated that the oxidation potentials of the polymers were lower than those of the monomers. The polymers showed electrochromism and changed the color from pale yellow to pale blue by application of voltage, presumably caused by the formation of polaron at the carbazole and triphenylamine moieties. The onset temperatures of weight loss of poly(1) and poly(2) were 225 and 270 °C under air.     

Cyclopolymerization. Part XXXII radical polymerization of α-(2-phenylallyloxy)methylstyrene: synthesis of highly cyclized polymers with high glass transition temperatures and thermal stability

A new 1,6-diene, α-(2-phenylallyloxy)methylstyrene (1), was synthesized and its radical cyclopolymerizations were studied, since 1 is expected to yield highly cyclized polymers with thermal stability and high glass transition temperatures. A low homopolymerization tendency of the monofunctional counterpart of 1 can be assumed reasonably, because it is a derivative of α-methylstyrene with a low ceiling temperature. This means that intermolecular propagation leading to pendant unsaturations is hard to occur during the polymerization of 1, which results in the formation of highly cyclized polymers. In fact, the degree of cyclization of poly(1) obtained at 180 °C attained the value 99%. Structural studies using a monomeric cyclic compound obtained by the telomerization of 1 permitted to assign main repeating cyclic units of poly(1) to a six-membered ring. The poly(1)s with a higher degree of cyclization were found to be stable up to 300 °C on thermogravimetric analyses and their glass transition temperatures were detected at temperatures over 250 °C.     

Syndiotactically enriched 1,2-selective polymerization of 1,3-butadiene initiated by iron catalysts based on a new class of donors

A series of phosphoryl (PO) contained compounds: triethylphosphate (a), diethylphenylphosphate (b), ethyldiphenylphosphate (c) triarylphosphates (d and h-m), triphenylphosphine oxide (e), phenyl diphenylphosphinate (f) and diphenyl phenylphosphonate (g) have been prepared. Iron catalysts, which are generated in situ by mixing the compounds with Fe(2-EHA)₃ and AlⁱBu₃ in hexane, are tested for butadiene polymerization at 50 °C. Phosphates donated catalysts have been, unprecedently, found to conduct extremely high syndiotactically (pentad, rrrr = 46.1-94.5%) enriched 1,2-selective (1,2-structure content = 56.2-94.3%) polymerization of butadiene. Introduction of electron withdrawing substituents on phenyl rings oftriphenylphosphate (k-m) remarkably promotes catalytic activity, while bulky substituent isopropyl at 2-position (h) has beneficial influence on regioselectivity. Employment of e, f or g as donor, results in a suppressed monomer conversion, accompanied by deteriorated 1,2-regioselectivity. The effects of polymerization conditions such as reaction temperature, types of cocatalysts and polymerization medium are also investigated by using catalyst system with tri(2,4-difluorophenyl)phosphate (m) as donor. Highly tolerance to polymerization temperature up to 80 °C is observed for the first time in the iron-based catalyst.     

Synthesis, characterization, and high gas permeability of poly(diarylacetylene)s having fluorenyl groups

Diarylacetylenes having fluorenyl groups and other substituents (trimethylsilyl, t-butyl, bromine, fluorine) (1a-1) were polymerized with TaCl₅-n-Bu₄Sn. Monomers 1a-l produced high molecular weight polymers 2a-l (M_w 5.1 × 10⁵-1.3 × 10⁶) in 12-59% yields. All of the polymers were soluble in common organic solvents, and gave tough free-standing membranes by the solution casting method. The onset temperatures of weight loss of polymers 2a-l in air were over 400 °C, indicating considerably high thermal stability. All the polymer membranes showed high gas permeability; e.g., the oxygen permeability coefficient (PO₂) of 2a was as large as 4800 barrers. Membrane 2d possessing two fluorine atoms at meta and para positions of the phenyl ring showed the highest oxygen permeability (PO₂ = 6600 barrers) among the present polymers.     

Synthesis and properties of various poly(diphenylacetylenes) containing tert-amine moieties

The polymerization of diphenylacetylene derivatives possessing tert-amine moieties, such as triphenylamine, N-substituted carbazole and indole, was examined in the presence of TaCl₅-n-Bu₄Sn (1:2) catalyst. A polymer with high molecular weight (M_w = 570 × 10³) was obtained in good yield by the polymerization of diphenylamine-containing monomer 1b, whereas the isopropylphenylamine derivative (1c) gave a polymer with relatively low molecular weight (M_w = 2.4 × 10³). The polymerization of monomer 1d containing cyclohexylphenylamine group did not proceed; however, carbazolyl- and indolyl-containing monomers also produced polymers. Poly(1b), poly(2f) and poly(4b) could be fabricated into free-standing membranes by casting toluene solutions of these polymers. The gas permeability of poly(1b) was too low to be evaluated accurately whereas poly(4b) possessing two chlorine atoms in the repeating unit showed higher gas permeability than that of poly(1b); furthermore, poly(2f) having trimethylsilyl and 3-methylindolyl groups exhibited relatively high gas permeability (). In the cyclic voltammograms of diphenylamino group-containing polymers, poly(1b) and poly(2b), the intensities of oxidation and reduction peaks decreased more than those of carbazolyl-containing poly(2a). The molar absorptivity (?) of poly(1b) at ∼700 nm increased with increasing applied voltage in the UV-vis spectrum.     

Polybinaphthyls incorporating chiral (R) or (S)-2,2′-binaphthyland oxadiazole moieties by Stille reaction

Chiral polymers P-1 and P-2 were prepared by the polymerization of (R)-3,3′-diiodo-2,2′-bisbutoxy-1,1′-binaphthyl ((R)-M-1) and (S)-3,3′-diiodo-2,2′-bisbutoxy-1,1′-binaphthyl ((S)-M-1) with 2,5-bis[(4-tributylstannyl)phenyl]-1,3,4-oxadiazole (M-2) via Pd(PPh₃)₄ catalyzed Stille coupling reaction. 1,3,4-Oxadiazole unit not only has high electron affinity, high thermal and oxidative stability, but also serves as a good chromophore. Polymers have strong blue fluorescence due to the efficient energy migration from the extended π-electronic structure of the polymers to the chiral binaphthyl core and can be expected to have potential application in the materials of fluorescent sensors. Circular dichroism (CD) spectra of polymers P-1 and P-2 are almost identical except that they gave opposite signals at each wavelength. The long wavelengths CD effect of P-1 and P-2 can be regarded as the more extended conjugated structure in the repeating unit and a high rigidity of the polymer backbone.     

Fluorescent chemosensor for metal ions based on optically active polybinaphthyls and 1,3,4-oxadiazole

Linear chiral polymers P-1 and P-2 were synthesized by the polymerization of (R)-5,5′-dibromo-6,6′-di(4-methylphenyl)-2,2′-bisoctoxy-1,1′-binaphthyl (R-M-1) with 2,5-di(4-vinylphenyl)-1,3,4-oxadiazole (M-2) and 2,5-di(4-tributylstannylphenyl)-1,3,4-oxadiazole (M-3) via Heck and Stille cross-coupling reaction, respectively. The chiral conjugated polymer P-1 can show strong green-blue fluorescence, and the chiral polymer P-2 shows strong blue fluorescence. While the conjugated polymers P-1 and P-2 were used as fluorescent chemosensor for metal ions, their fluorescence can be efficiently quenched on the addition of different metal ions. The obvious quenching effect of the polymers P-1 and P-2 indicates that the intramolecular photoinduced electron transfer (PET) or photoinduced charge transfer (PCT) between the polymer backbone and receptor-ions in the main chain of fluorescent chemosensor can lead to the pronounced fluorescence quenching. The results also show that the chiral polymers P-1 and P-2 incorporating 1,3,4-oxadiazole moiety as the recognition site can act as a special fluorescent chemosensor for the appropriate detection of the sensitive and selective sense of metal ions.     

Poly(7-oxanorbornenes) carrying 2,2,6,6-tetramethylpiperidine-1-oxy (TEMPO) radicals: Synthesis and charge/discharge properties

TEMPO-containing 7-oxanorbornene monomers 1-4 (TEMPO = 2,2,6,6-tetramethylpiperidine-1-oxy) were synthesized and polymerized via ring-opening metathesis using a ruthenium carbene catalyst. Monomers 1 and 3 gave polymers with number-average weights of 80?100 and 112?200 in 85 and 96% yields, respectively, whereas monomers 2 and 4 did not provide high molecular weight polymers. Poly(1) and poly(3) were soluble in common solvents including CHCl₃, CH₂Cl₂ and THF, while insoluble in hexane, diethyl ether and MeOH. They were thermally stable up to ca. 240 °C according to the TGA measurements in air. The secondary batteries utilizing the present polymers as cathode-active material demonstrated reversible charge/discharge processes, whose discharge capacities were 107 and 92.8 A h/kg, and displayed excellent high-rate charge and discharge properties. These cells demonstrated excellent cycle life, e.g., the discharge capacities of poly(1) and poly(3) showed less than 10% decrements even after 100 cycles.     

Synthesis and properties of polyacetylenes carrying N-phenylcarbazole and triphenylamine moieties

Novel acetylene monomers containing N-phenyl-substituted carbazole (Cz) and triphenylamine (TPA) groups, namely, 3-ethynyl-9-phenylcarbazole (1) and p-(N,N-diphenylamino)phenylacetylene (2) were synthesized, and polymerized with several Rh-, W-, and Mo-based catalysts. Poly(1) and poly(2) with high number-average molecular weights (15?500-974?000) were obtained in good yields (77-97%), when [(nbd)RhCl]₂-Et₃N (nbd = norbornadiene) was used as a catalyst. The polymers exhibited UV-vis absorption peaks derived from the Cz and TPA moieties at 250-350 nm and polyacetylene backbone above 350 nm. The UV-vis absorption band edge wavelengths of the polymers were longer than those of the corresponding monomers. Poly(2) exhibited a UV-vis absorption peak at a longer wavelength than poly(1) did, which indicates that poly(2) has main chain conjugation longer than that of poly(1). The molecular weights and photoluminescence quantum yields of the polymers obtained by the polymerization using [(nbd)RhCl]₂-Et₃N were larger than those of the Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃]-based counterparts. The cyclic voltammograms of the polymers indicated that they had clear electrochemical properties; the onset oxidation voltage of poly(1) was higher than those of N-alkyl-substituted Cz derivatives. The polymers showed electrochromism and changed the color from pale yellow to blue by application of voltage, presumably caused by the formation of charged polaron at the Cz and TPA moieties. The temperatures for 5% weight loss of the polymers were around 350-420 °C under air, indicating the high thermal stability.     

Synthesis of poly(1-β-naphthyl-2-phenylacetylene) membranes through desilylation and their properties

The polymerization of 1-β-naphthyl-2-[(p-trimethylsilyl)phenyl]acetylene (8a) with TaCl₅-n-Bu₄Sn in cyclohexane provided a high molecular weight polymer (9a) (M_w=3.4×10⁶). The corresponding monomers having p-dimethyl-t-butylsilyl and p-dimethyl(10-pinanyl)silyl groups in place of p-trimethylsilyl group in 8a also polymerized in a similar way to give high molecular weight polymers (9b, 9c, respectively; M_w>1×10⁶). All these polymers were soluble in many common solvents such as toluene and chloroform, and provided free-standing membranes by casting from toluene solution. The oxygen permeability coefficients (P_O2) of 9a at 25 °C was as high as 3500 barrers. The membrane of poly(1-β-naphthyl-2-phenylacetylene) (10a) was prepared by desilylation of the membrane of 9a with trifluoroacetic acid. Polymer 10a was insoluble in any solvents, and showed high thermal stability (the onset temperature of weight loss in air ∼470 °C). The P_O2 value of 10a reached 4300 barrers. Not only the membrane of 9c but also its desilylation product 10c exhibited large optical rotations ([α]_D=+2924 and +9800°, respectively) and strong CD signals. This indicates that the membrane of 10c maintains the helical main chain conformation of 9c with a large excess one-handed helix sense.     

Synthesis and characterization of side-chain liquid crystalline homopolymers and block copolymers containing biphenyl-4-ylthiophene and biphenyl-4-ylfluorene pendants

A series of new liquid crystalline homopolymers (P1 and P2) and block copolymers (P3 and P4) composed of methacrylates containing pendant biphenyl-4-ylthiophene (M1) and biphenyl-4-ylfluorene (M2) units were synthesized by atom transfer radical polymerization (ATRP). The number-average molecular weights (M_n) of the homopolymer (P2) and diblock copolymers (P3 and P4) were in the range of 5153-8713 g mol⁻¹ with polydispersity indices (PDIs) between 1.17 and 1.25. The thermal, mesogenic, and photoluminescence (PL) properties of all polymers were investigated. Except for the absence of mesogenic properties in block copolymer P4, polymers P1 and P3 possessed the smectic A phase and polymer P2 exhibited the nematic phase. Moreover, the mesomorphism and the layer d-spacing values of the smectic A phase in polymers P1 and P3 were confirmed and characterized by X-ray diffraction (XRD) patterns.     

Properties of organosoluble aromatic polyimides from 3′-trifluoromethyl-3,4′-oxydianiline

A colorless fluorinated diamine, 3′-trifluoromethyl-3,4′-oxydianiline (3′-CF₃-3,4′-ODA) (II) was prepared through the nucleophilic substitution reaction of 3-nitrophenol and 2-chloro-5-nitrobenzotrifluoride by catalytic reduction with hydrazine and Pd/C. A series of Polyimides V were synthesized from the diamine II with various aromatic dianhydrides III_a-f via thermal and chemical imidization. These polyimides had inherent viscosities ranging from 0.88 to 1.12 dl/g. A comparison of V, VI to analogous polyimides VII, VIII. VI, VII and VIII was based on 3′4-ODA, 3-CF₃-4,4′-ODA, 4,4′-ODA, respectively. In terms of the color of PI revealed that the color intensity of phenoxy-containing amine of the meta-structure and the para-structure with the CF₃ group would fell off color intensity. The color intensity of the four polyimide series was lessened in the following order: V>VII>VI>VIII. The solubility of V is better than VI, VII and VII. The polyimide V films had a tensile strength ranging from 124 to 147 MPa, elongation at break from 9 to 65%, and initial modulus from 2.3 to 2.8 GPa. The glass transition temperature of polymers was recorded at 234-313 °C. They had 10% weight loss at a temperature above 515 °C and left more than 50% residue even at 800 °C in nitrogen. Compared with polyimides VI, V showed the lower dielectric constants of 2.80-3.50 (40 MHz), and moisture absorptions in the range of 0.44-1.02 wt%.     

Synthesis and characterization of alternating fluorene-based copolymers containing diaryl- and non-substituted bithiophene units

A series of soluble alternating fluorene-based copolymers containing diaryl- and non-substituted bithiophene units are synthesized by palladium-catalyzed Suzuki coupling reaction. All polymers demonstrate green colors of photoluminescence (PL) in chloroform, good thermal stability (with decomposition temperatures above 436 °C), and high glass transition temperatures (in the range of 120-144 °C). Owing to the large steric hindrance of diaryl substituents on bithiophenes in the polymers (P2-P4), the aggregation of solids is reduced as well as the solubility is improved, so the performance of their PLED devices are superior to that of the non-substituted polymer (P1). Compared with P1, the introduction of substitutents at 3,3′-position of bithiophene in P2-P4 has significant effects on the photophysical properties of resulting polymers in solution and solid states. Though the PL quantum yield of P1 is much higher than those of diaryl-substituted polymers (P2-P4), the PLED device of P1 has the worst electroluminescence (EL) properties due to the poor solubility of P1. Consequently, among these polymers, the device made of P3 as an emitter has the highest luminance of 2590 cd/m² at 9.5 V. For optimum device performance, a device of P3 blended with PVK can be further enhanced to a brighter luminance of 4284 cd/m² at 18 V.     

Pd-catalyzed hydrosilylation polymerization of a dihydrosilane with diyne/triyne mixed systems affording crosslinked silylene-divinylene polymers and their properties

Treatment of a dihydrosilane (methylphenylsilane, 1) with mixtures of a diyne (p- or m-diethynylbenzene, 2a or 2b) and a triyne (1,3,5-triethynylbenzene, 3a or B,B′,B″-triethynyl-N,N′,N″-trimethylborazine, 3b; 1:2:3=100:95:5, 100:90:10, 100:80:20) in the presence of Pd-PCy₃ (Cy=cyclohexyl) catalyst gave new crosslinked silylenedivinylene polycarbosilanes. In TGA the resulting crosslinked polymers tended to show higher Td₅ values and higher char yields than the corresponding linear polymers. On the other hand, UV/vis absorption spectra of the crosslinked polymers obtained in the reactions of 2a or 2b with 3a exhibited increased broad peaks around 390 nm for 2a or 360 nm for 2b. Coincidently, their fluorescence spectra showed significant increase of the emission peaks in 400-550 nm. The crosslinked polymer derived from 2a and 3b, however, showed decrease of the absorption peak around 390 nm and profound depression of fluorescence peaks in 400-550 nm.