Effects of microstructural functional polyaniline layers on SPEEK/HPW proton exchange membranes

In this study, a method is developed to fabricate sulfonated poly (ether ether ketone)/phosphotungstic acid‐polyaniline (SPEEK/HPW‐PANI) membranes by in situ polymerization of aniline for the purpose of decreasing the weight loss of HPW in the membranes. The synthesis involves the production of a SPEEK/HPW hybrid membrane followed by different layer of PANI coatings on the membrane surface, and subsequent treatment using drying in vacuum procedures. The scanning electronic microscopy images showed that HPW had good compatibility with SPEEK polymers and energy dispersive X‐ray spectroscopy revealed the successfully doping with HPW and polymerization of PANI. The surface of SPEEK/HPW‐PANI becomes more compact than that of SPEEK/HPW and pure SPEEK, which may lead to reduce the water uptake and swelling property. The proton conductivity was found for the SPEEK/HPW‐PANI‐5 composite membrane (91.53 mS/cm at 80°C) higher than that of pure SPEEK membrane (68.72 mS/cm at 80°C). Better thermal stability was determined in both SPEEK/HPW and SPEEK/HPW‐PANI membranes than pristine SPEEK membrane. Therefore, PANI is a good potential coating for organic–inorganic hybrid e.g. SPEEK/HPW membrane materials to improve their hydrothermal stable properties and SPEEK/HPW PANI is a material that shows promise as a proton exchange membranes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41033.     

Montmorillonite‐reinforced sulfonated poly(phthalazinone ether sulfone ketone) nanocomposite proton exchange membranes for direct methanol fuel cells

To produce a composite membrane with high conductivity and low permeability, SPPESK with a degree of sulfonation of 101% was carefully selected for the preparation of montmorillonite (MMT)‐reinforced SPPESK using solution intercalation. The fundamental characteristics such as water uptake, swelling ratio, proton conductivity, methanol permeability, and mechanical properties of the composite membranes were studied. Water uptake is improved when organic MMT (OMMT) loading increase. The composite membranes with CTAB‐MMT loading of 4–0.5% show 0.143–0.150 S cm^?1 proton conductivity at 80°C, which approaches the value of Nafion112. In addition, methanol permeability was decreased to 6.29 × 10^?8 cm² s^?1 by the addition of 6 wt % OMMT. As a result, the SPPESK‐MMT composite membrane is a good candidate for use in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39852.     

Vinyl‐addition type norbornene copolymers containing flexible spacers and sulfonated pendant groups for proton exchange membranes

Novel sulfonated poly(2‐butoxymethylenenorbornene‐co‐2‐(6‐phenoxy‐hexyloxymethylene)‐5‐norbornene [sP(BN/PhHN)] were prepared successfully through vinyl‐addition type polymerization and then sulfonated with concentrated sulfuric acid (98%) as sulfonating agent in a component solvent. The sP(BN/PhHN)‐40 with the maximal degree of sulfonation of 40% can be obtained by controlling the sulfonating reaction time from 8 to 20 h, and a proton conductivity of 3.35 × 10^?3 S/cm was achieved at 70°C. The methanol permeabilities of these membranes were in the range from 0.26 to 6.58 × 10^?7 cm²/s, which were remarkably lower than Nafion (2.36 × 10^?6 cm²/s). TEM analysis revealed that these side‐chain type membranes have a microphase separated structure composed of hydrophilic side‐chain domains and hydrophobic polynorbornene main chain domains. Sulfonated polynorbornene containing soft spacers displayed better properties, such as lower water uptake, high thermal properties, mechanical properties, and low methanol permeability. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Polybenzimidazole‐graft‐polyvinylphosphonic acid—proton conducting fuel cell membranes

A new method for the preparation of polybenzimidazole (PBI)‐based membranes, containing high concentrations of immobilized phosphonic acid groups, has been developed. The procedure used is carried out in two steps: (1) Synthesis of modified PBIs, containing 1,2‐dihydroxypropyl groups and preparation of films there from; (2) Introduction of vinylphosphonic acid (VPA) and initiator (cerium ammonium nitrate) in the film, subsequent grafting of VPA from the active sites of the PBI backbone. Membranes with different length of the grafted polyvinylphosphonic acid chains were prepared. The molar ratio grafted VPA units per PBI repeating unit reaches 7.8. Proton conductivity was measured at 120°C and relative humidity (RH) 20–100%. For the membrane with highest concentration of phosphonic acid groups the proton conductivity was 35 mS cm^?1 at 100% RH and 8 mS cm^?1 at 20% RH. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Enhanced proton conductivity from phosphoric acid‐incorporated 3D polyacrylamide‐graft‐starch hydrogel materials for high‐temperature proton exchange membranes

To enhance anhydrous proton conductivity of high‐temperature proton exchange membranes (PEMs), we report here the realization of H₃PO₄‐imbibed three‐dimensional (3D) polyacrylamide‐graft‐starch (PAAm‐g‐starch) hydrogel materials as high‐temperature PEMs using the unique absorption and retention of crosslinked PAAm‐g‐starch to concentrated H₃PO₄ aqueous solution. The 3D framework of PAAm‐g‐starch matrix provides enormous space to keep H₃PO₄ into the porous structure, which can be controlled by adjusting crosslinking agent and initiator dosages. Results show that the H₃PO₄ loading and therefore the proton conductivities of the membranes are significantly enhanced by increasing the amount of crosslinking agent and initiator dosages. Proton conductivities as high as 0.109 S cm^?1 at 180°C under fully anhydrous state are recorded. The high conductivities at high temperatures in combination with the simple preparation, low cost, and scalable matrices demonstrate the potential use of PAAm‐g‐starch hydrogel materials in high‐temperature proton exchange membrane fuel cells. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40622.     

Modification of SPPESK proton exchange membranes through layer‐by‐layer self‐assembly

Sulfonated poly(phthalazinone ether sulfone ketone) (SPPESK) composite membranes are fabricated through electrostatic layer‐by‐layer (LbL) self‐assembly method with chitosan (CS) and phosphotungstic acid (PWA) to enhance the proton conductivity and stability. The results demonstrate that LbL self‐assembly has different effects on the SPPESK membrane substrates with different sulfonation degrees (DSs). It elevates proton conductivity of the SPPESK membrane of lower DS and enhances swelling stability of the SPPESK membrane of higher DS. For instance, at 80°C, proton conductivity of the SPPESK0.74/(CS/PWA)₁ membrane (lower DS) increases by 16%–96.49 mS cm^?1, and swelling ratio of the SPPESK1.01/(CS/PWA)₃ membrane (higher DS) decreases from 58 to 29%. Attribute to the electrostatic interaction and ion cross‐linking networks, permeability of the SPPESK0.74/(CS/PWA)₃ membrane and the SPPESK1.01/(CS/PWA)₅ membrane are reduced by 45 and 30%, respectively. The results indicate that the LbL self‐assembly has broadened the available DS range for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42867.     

Preparation and characterization of proton exchange membrane based on polyphosphoric acid modified by PVDF‐HFP

A polyphosphoric acid functionalized proton exchange membrane (PEM) was prepared by a ring opening reaction using the epoxycyclohexylethyltrimethoxysilane (EHTMS) and amino trimethylene phosphonic acid (ATMP) as raw materials and was modified by poly(vinylidene fluoride)–hexafluoro propylene (PVDF‐HFP). The structure of the membranes was characterized by Fourier transform infrared and scanning electron microscopy. The X‐ray photoelectron spectroscopy explores the content of the elements in the membrane related to the ion exchange capacity value. The membranes’ properties including water uptake, swelling ratio, proton conductivity, and hydrolysis stability were studied. Performance tests show that when ATMP/EHTMS = 1/5, conductivity of the PVDF‐HFP modified PEMs increased from 0.83 × 10^?4 S cm^?1 at 20 °C to 9.53 × 10^?3 S cm^?1 at 160 °C, the swelling ratio of membranes decreased from 2.71% to 2.13%. The results indicate that the introduction of F atoms is beneficial to increase the proton conductivity and the dimensional stability. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46737.     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Solution‐blown SPEEK/POSS nanofiber–nafion hybrid composite membranes for direct methanol fuel cells

This study aims to develop novel hybrid composite membranes (NHMs) by impregnating Nafion solution into the porous sulfonated poly(ether ether ketone)/polyhedral oligomeric silsesquioxanes (SPEEK/POSS) nanofibers (NFs). The composite membrane was prepared by solution blowing of a mixture of SPEEK/POSS solution. The characteristics of the SPEEK/POSS NFs and the NHMs, including morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of NHMs was compared with that of Nafion117 and SPEEK/Nafion composite membranes. Results showed that the introduction of POSS improved the proton conductivity, water swelling, and methanol permeability of membranes. A maximum proton conductivity of 0.163 S cm^?1 was obtained when the POSS content was 6 wt % at 80°C, which was higher than that of Nafion117 and SPEEK/Nafion. NHMs could be used as proton exchange membranes (PEMs) for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42843.     

Novel imidazole‐grafted hybrid anion exchange membranes based on poly(2,6‐dimethyl‐1,4‐phenylene oxide) for fuel cell applications

Novel organic–inorganic hybrid membranes, based on poly(2,6‐dimethyl‐1,4‐phenylene oxide), have been prepared through 1,2‐dimethylimidazole functional groups and double crosslinking agents including 3‐glycidyloxypropyltrimethoxysilane and tetraethyl orthosilicate by sol–gel process for the purpose of improving the conductivity and alkaline resistance. The structure of membranes was characterized using Fourier‐transform infrared spectra, ¹H NMR, and X‐ray diffraction. The physico‐chemical properties of all membranes were shown in ion exchange capacity, water uptake, stability, and conductivity. Membranes with OH^– conductivity up to 0.022 at 25 °C and 0.036 S cm^?1 at 80 °C. Promisingly, the chemical stability of the resulting membranes remains unchanged after storage in 2 mol dm^?3 KOH at 25 °C over at least 10 days. The tensile strength can be higher than 30 MPa, and the elongation at break (Eb) is in the range 6.68–10.84%. Hence, this hybrid membrane can be potentially applied in alkaline fuel cells. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46034.     

Development of antifouling polyamide thin‐film composite membranes modified with amino‐cyclodextrins and diethylamino‐cyclodextrins for water treatment

The fouling behavior of polyamide thin‐film composite (TFC) membranes modified with amino‐ and diethylamino‐cyclodextrins (CDs) through an in situ interfacial polymerization process is reported. Modified polyamide TFC membranes exhibited improved hydrophilicity, water permeability, and fouling resistance as compared to the unmodified TFC membranes, while restricting the passage of NaCl salt (98.46 ± 0.5%). The increase in hydrophilicity was attributed to the secondary and tertiary hydroxyl groups of the CDs, which were not aminated. The membranes modified with amino‐CDs had increased surface roughness while the membranes modified with diethylamino‐CDs had smoother surfaces. However, despite the surface roughness of the membranes modified with amino‐CDs, low fouling was observed due to the highly hydrophilic surfaces, which superseded the roughness. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40109.     

Novel membranes based on poly(5‐(methacrylamido)tetrazole) and sulfonated polysulfone for proton exchange membrane fuel cells

Proton‐exchange membrane fuel cells (PEMFC)s are increasingly regarded as promising environmentally benign power sources. Heterocyclic molecules are commonly used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. In this study, 5‐(methacrylamido)tetrazole monomer, prepared by the reaction of methacryloyl chloride with 5‐aminotetrazole, was polymerized via conventional free radical mechanism to achieve poly(5‐(methacrylamido)tetrazole) homopolymer. Novel composite membranes, SPSU‐PMTetX, were successfully produced by incorporating sulfonated polysulfone (SPSU) into poly(5‐(methacrylamido)tetrazole) (PMTet). The sulfonation of polysulfone was performed with trimethylsilyl chlorosulfonate and high degree of sulfonation (140%) was obtained. The homopolymers and composite membranes have been characterized by NMR, FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). ¹H‐NMR and FTIR confirmed the sulfonation of PSU and the ionic interaction between sulfonic acid and poly(5‐(methacrylamido)tetrazole) units. TGA showed that the polymer electrolyte membranes are thermally stable up to ～190°C. Scanning electron microscopy analysis indicated the homogeneity of the membranes. This result was also supported by the appearance of a single T_g in the DSC curves of the blends. Water uptake and proton conductivity measurements were, as well, carried out. Methanol permeability measurements showed that the composite membranes have similar methanol permeability values with Nafion 112. The maximum proton conductivity of anhydrous SPSU‐PMTet0.5 at 150°C was determined as 2.2 × 10^?6 S cm^?1 while in humidified conditions at 20°C a value of 6 × 10^?3 S cm^?1 was found for SPSU‐PMTet2. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40107.     

Proton‐conductive membranes based on vanadium substituted heteropoly acids with Keggin structure and polymers

In this article, novel proton‐conducting composite membranes SPEEK/PW₁₁V and PVA/SiW₁₁V were synthesized from vanadium substituted heteropoly acids (H₄PW₁₁VO₄₀·8H₂O and H₅SiW₁₁VO₄₀·15H₂O, abbreviated as PW₁₁V and SiW₁₁V) and polymers (SPEEK or PVA) at the weight ratio 70 : 30. The membranes were characterized by the infrared spectroscopy, X‐ray powder diffraction, and scanning electron microscopy, which confirmed the maintenance of the Keggin framework and dispersion homogeneously in the polymer matrix without long‐range ordering. Their proton‐conducting properties were investigated with electrochemical impedance spectroscopy. The results show that the respective proton conductivities of SPEEK/PW₁₁V and PVA/SiW₁₁V membranes were in the order of 10^?2 and 10^?4 S cm^?1 at ambient temperature. The temperature dependence of the two composite membrane electrolytes exhibit Arrhenius behavior, and the observed activation energies to be 15.82 kJ mol^?1 for SPEEK/PW₁₁V and 14.40 kJ mol^?1 for PVA/SiW₁₁V, which indicates that the proton conduction complies with the Grotthuss mechanism. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42204.     

Polyacrylonitrile‐based proton conducting membranes containing sulfonic acid and tetrazole moieties

Proton conducting membranes based on polymers containing sulfonic acid and tetrazole moieties were developed. Successful syntheses of poly(acrylonitrile‐co ‐styrene sulfonic acid) (PAN‐co ‐PSSA), poly(acrylonitrile‐co ‐5‐vinyl tetrazole) (PAN‐co ‐PVTz), and poly(acrylonitrile‐co ‐5‐vinyl tetrazole‐co ‐styrene sulfonic acid) (PAN‐co ‐PVTz‐co ‐PSSA) were confirmed by ¹H‐nuclear magnetic resonance spectroscopy, elemental analysis, and Fourier transform infrared spectroscopy. Two approaches were performed to study the effects of molar ratio of sulfonic acid to tetrazole and tetrazole content on membrane properties. In the first approach, PAN‐co ‐PSSA was blended with PAN‐co ‐PVTz at three molar ratios. The second approach focused on PAN‐co ‐PVTz‐co ‐PSSA membranes with various tetrazole contents. PAN‐co ‐PSSA membrane was also prepared. All solution‐cast membranes were hydrolytically stable, except for PAN‐co ‐PVTz‐co ‐PSSA with 71% tetrazole. Surface morphologies of blend membranes were studied using scanning electron microscopy, and no phase separation was observed. Water uptake was shown to increase with increasing tetrazole. All membranes exhibited high thermal stability (up to 250 °C) and high storage moduli. Proton conductivity was found to depend significantly on relative humidity. The influences of sulfonic acid to tetrazole ratio and tetrazole content on proton conduction were observed and discussed. A maximum proton conductivity of 7.1 × 10^?3 S/cm at 26 °C was obtained from PAN‐co ‐PSSA membrane. In addition, all tested membranes showed relatively good oxidative stability after treatment in Fenton's reagent. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45411.     

Comparative study of composite membranes from nano‐metal‐oxide‐incorporated polymer electrolytes for direct methanol alkaline membrane fuel cells

A series of six composite membranes was prepared with two polymer electrolytes and three inorganic fillers, namely, silica, titania, and zirconia by a solution casting method. Two polymer electrolytes, that is, anion‐exchange membranes, were prepared from polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene (PSEBS) and polysulfone by chloromethylation and quaternization. A preliminary characterization of the ionic conductivity, methanol permeability, and selectivity ratio was done for all of the prepared composite membranes to check their suitability to work in direct methanol alkaline membrane fuel cells (DMAMFCs). The DMAMFC performance was analyzed with an in‐house fabricated single cell unit with a 25‐cm² area. Maximum performance was achieved for the composite membrane quaternized PSEBS/7.5% TiO₂ and was 74.5 mW/cm² at 60°C. For the comparison purposes, a commercially available anion‐exchange membrane (Anion Membrane International‐7001) was also investigated throughout the study. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Durability and performance of polystyrene‐b‐poly(vinylbenzyl trimethylammonium) diblock copolymer and equivalent blend anion exchange membranes

Anion exchange membranes (AEM) are solid polymer electrolytes that facilitate ion transport in fuel cells. In this study, a polystyrene‐b‐poly(vinylbenzyl trimethylammonium) diblock copolymer was evaluated as potential AEM and compared with the equivalent homopolymer blend. The diblock had a 92% conversion of reactive sites with an IEC of 1.72 ± 0.05 mmol g^?1, while the blend had a 43% conversion for an IEC of 0.80 ± 0.03 mmol g^?1. At 50°C and 95% relative humidity, the chloride conductivity of the diblock was higher, 24–33 mS cm^?1, compared with the blend, 1–6 mS cm^?1. The diblock displayed phase separation on the length scale of 100 nm, while the blend displayed microphase separation (～10 μm). Mechanical characterization of films from 40 to 90 microns thick found that elasticity and elongation decreased with the addition of cations to the films. At humidified conditions, water acted as a plasticizer to increase film elasticity and elongation. While the polystyrene‐based diblock displayed sufficient ionic conductivity, the films' mechanical properties require improvement, i.e., greater elasticity and strength, before use in fuel cells. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41596.     

Branched poly(biphenylene-co-sulfone)ether ion exchange membranes containing perfluorocyclobutane groups for fuel cell applications

A series of branched poly(biphenylene-co-sulfone) ion exchange membranes containing perfluorocyclobutane groups were prepared for fuel cells. Two bifunctional trifluorovinyloxy-terminated monomers (sulfonable 4,4′-bis(trifluorovinyloxy)biphenyl and insulfonable 4,4′-sulfonyl-bis(trifluorovinyloxy)biphenyl) and a trifunctional trifluorovinyloxy-terminated branching agent (1,1,1-tris(4′-trifluorovinyloxyphenyl)ethane) were synthesized and terpolymerized via thermal [2π + 2π] cyclodimerization to obtain partially fluorinated and branched polymers containing 0–5 mol% of the branching agent. They were then postsulfonated by chlorosulfonic acid at room temperature, cast as membranes, and characterized to evaluate their electrochemical properties for fuel cell applications. As the branching agent content was increased, their polydispersity values highly increased, indicating they became highly branched. It was confirmed that higher branching agent content also increased the ion exchange capacity, water uptake, and proton conductivity of the branched ion exchange membranes containing perfluorocyclobutane groups. This indicates that their electrochemical properties can be easily controlled by the degree of branching. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48373.     

Quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone blend composite membrane doped with ZnO‐nanoparticles for alkaline fuel cells

A series of quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone (QPPO/PSF) blend anion exchange membrane (AEM) were successfully fabricated and characterized for alkaline fuel cell application. Zinc oxide (ZnO) nanoparticles were introduced in the polymer matrix to enhance the intrinsic properties of the AEM. To confirm successful fabrication, Fourier‐transform infrared spectroscopy and nuclear magnetic resonance (¹H‐NMR) were used. The membrane properties were enhanced by the addition of ZnO nanoparticles. The addition of ZnO nanoparticles resulted to a higher ion exchange capacity (IEC) of 3.72 mmol g^?1, increase of ion conductivity (IC) up to 52.34 mS cm^?1 at 80 °C, enhancement of water uptake, and reduced methanol permeability. The QPPO/PSF/2% ZnO composite retained over 80% of its initial IC at room temperature and also retained over 50% of its initial IC at 80 °C when evaluated for alkaline stability. The maximum power output reached for the membrane electrode assembly constructed with QPPO/PSF/2%ZnO was 69 mW cm^?2 at room temperature, which is about three times more than the parent QPPO membrane. The above results indicate that QPPO/PSF/ZnO is a good candidate as an AEM for fuel cell application. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45959.     

Synthesis and properties of fluorine‐ and siloxane‐containing polybenzimidazoles for high temperature proton exchange membrane fuel cells

In this study, new fluorine–siloxane‐containing polybenzimidazole (PBI) copolymers were synthesized by copolymerization of 3,3′‐diaminobenzidine, 2,2‐bis(4‐carboxyphenyl)‐hexafluoropropane (HFA), and 1,3 bis(carboxypropyl)tetramethyldisiloxane (BTMDS) with different molar ratios. PBI copolymer membranes were prepared by solution‐casting and then doped with phosphoric acid. The structures of PBI copolymers were characterized by FTIR and X‐ray diffraction. The solubility of the PBI copolymers was significantly increased by the introduction of the bulky HFA group and the flexible BTMDS group into the polymer backbone. The PBI copolymers still maintained good thermal stability and mechanical properties. Because of the introduction of the flexible and hydrophobic siloxane group in the polymer backbone, the methanol permeability was reduced and the proton conductivity under anhydrous condition at high temperatures was increased compared to the PBI without the siloxane group. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4107–4112, 2013     

Preparation and characterization of novel chitosan‐based mixed matrix membranes resistant in alkaline media

In this work, mixed matrix membranes (MMMs) based on chitosan (CS) and different fillers (room temperature ionic liquid [emim][OAc] (IL), metallic Sn powder, layered titanosilicate AM‐4 and layered stannosilicate UZAR‐S3) were prepared by solution casting. The room temperature electrical conductivity and electrochemical response in strong alkaline medium were measured by electrochemical impedance spectroscopy and cyclic voltammetry (CV). The ionic conductivity of pure CS membranes was enhanced, from 0.070 to 0.126 mS cm^?1, for the pristine CS and Sn/CS membranes, respectively, as a function of the hydrophilic nature of the membrane and the coordination state of Sn. This hydrophilic and charge nature was corroborated by water uptake measurements, where only the introduction of IL in the CS membrane led to a water uptake of 3.96 wt %, 20 or 30 times lower than the other membranes. Good thermal and chemical stability in alkaline media were observed by thermogravimetric analyses and X‐ray photoelectron spectroscopy analyses, respectively, and good interaction between CS and the fillers observed by X‐ray diffraction, scanning electron microscopy and CV. Thus, thin CS‐based MMMs (40–139 µm), resistant in high alkaline media, show higher conductivity than pure CS membranes, especially those fillers containing tin, and although the electrochemical performance is lower than commercially available anion‐exchange membranes they have potential in pervaporation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42240.