Study of plastic compounds containing polypropylene and wood derived fillers from waste of different origin

The scope of the article was to study the perspectives of the using of wood derived fillers (WDF) from waste of different origin as fillers of polypropylene. The WDF used in this study was hard wood flour (HW), birch veneer polishing dust (VD) and tetra‐pack carton cellulose fiber (TC). Some mechanical strength parameters, water uptake in the static and cyclic test and resistance to fungal decay of polypropylene (PP) composites containing these three types of WDF were studied and compared with similar loading (40 wt %) talc‐filled PP. Composites containing TC and VD fibers as filler showed the highest flexural strength at three test temperatures (?40, +20, and +40°C) and flexural modulus and tensile strength at plus temperatures. On the other hand talc‐filled PP exhibited greatest flexural modulus at minus temperature, greatest impact strength at room temperature and best flow ability. Significant difference was observed between PP composites with HW and VD fillers regarding water uptake in cyclic tests, however flexural strength and modulus change of composites were reversible after drying. No weight loss of WDF/PP composites was observed after 6 week exposure to brown‐ and white‐rot fungi, however, degradation of the surface of samples was detected by SEM. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Valorization of waste thermoset material as a filler in thermoplastic: Mechanical properties of phenolic molding compound waste‐filled PP composites

As most thermoset material, phenolic molding compound (PMC) wastes are an environmental problem. Very few recycling solutions have been proposed so far for this type of material. A mechanical recycling method to valorize these materials is proposed in this work. It relies on the use of phenolic waste as filler in thermoplastic. Such phenolic filler can increase mechanical properties (tensile, flexural) of the matrix, and be used in substitution of traditional particulate fillers such as calcium carbonate or talc. In this study, several morphological parameters influencing the final mechanical properties of a PMC‐filled polypropylene (PP) micro‐composite are studied, such as filler loading rate, particles size distribution of the filler, and interfacial adhesion between the filler and the matrix. Some structural parameters are also studied and linked with mechanical properties, such as dispersion of the filler and crystallinity of the matrix. Finally, the properties of PMC‐filled PP are compared with CaCO₃‐ and talc‐filled PP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45849.     

Surface‐modified talc particles by acetoxy groups grafting: Effects on mechanical properties of polypropylene/talc composites

This article deals with the effects of surface‐modified talc particles on mechanical properties of polypropylene (PP)/talc composites. These materials were prepared by injection molding of PP blended with different concentrations of nontreated and treated talc, under the same processing conditions. Differential thermal calorimetry and scanning electron microscopy were used to assess thermal properties and morphology of the final composites. The reinforcing effect of talc, either treated or nontreated surface, on PP is analyzed through the tensile properties as a function of the mineral content (0–10 wt%). Morphological structure of composites revealed that the talc treatment improved the particle dispersion and distribution within the PP matrix and enhanced the interfacial PP‐talc adhesion. The mechanical properties of these composites, especially the Young modulus, tensile strength and elongation at break, were found to be improved respect to PP‐untreated talc ones. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Effect of chemical treatments on the mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

This study was performed with commercially available phenyl trimethoxysilane (PTMS) and neoalkoxytitanate [i.e., neopentyl(diallyl)oxytri(dioctyl)phosphato titanate (LICA 12)] as coupling agents. PTMS and LICA 12 were used to treat talc and kaolin to compare their effects with untreated fillers upon incorporation into polypropylene (PP). Single‐filler PP composites (containing either talc or kaolin) and hybrid‐filler composites (containing a mix of both talc and kaolin) were compounded in a twin‐screw extruder and subsequently injection‐molded into dumbbells. The incorporation of PTMS and LICA 12 slightly decreased the tensile and flexural properties in terms of modulus and strength but increased the elongation at break for both single‐filler and hybrid‐filler composites. There was also a significant improvement in the impact strength of the composites, particularly those treated with LICA 12. The hybrid composites, through the synergistic coalescence of positive characteristics from talc and kaolin with the aid from chemical treatment provided an economically advantageous material with mechanical properties comparable to those of the single‐filler‐filled PP composites. Further investigations on flow and morphological properties were also done to correlate the mechanical properties of the single‐ and hybrid‐filler‐filled PP composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical characterization and application of Weibull statistics to the strength of softwood lignin‐based carbon fibers

Mechanical characterization of the first generation of softwood kraft lignin‐based carbon fibers (CF) was carried out. The single‐fiber tensile tests of filaments with different diameters and length were performed to evaluate stiffness and strength of carbon fibers. The average mechanical properties were measured as follows: tensile strength of approximately 300 MPa, the elastic modulus of 30 GPa and a strain at failure within interval of 0.7–1.2%. The fiber strength data was evaluated by the two‐parameter Weibull statistics and parameters of this distribution were obtained. Although strength of the produced fibers is still significantly lower than that of commercially available, the experimental results and predictions based on Weibull statistics show a fairly good fit. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3689–3697, 2013     

An investigation on the mechanical and dynamic rheological properties of single and hybrid filler/polypropylene composites based on talc and calcium carbonate

Some results of experiments on the mechanical and rheological properties of mineral filled polypropylene were presented. Single filler and hybrid filler composites of talc and calcium carbonate (CaCO₃) were prepared in a co‐rotating twin‐screw extruder. The effect of filler type, filler content, and coupling agent on the mechanical and rheological properties of the polypropylene were studied. The coupling agent was maleic anhydride‐grafted polypropylene (PP‐g‐MA). It was found that the mechanical properties are affected by filler type, filler concentration, and the interaction between filler and matrix. The tensile strength of the composite is more affected by the talc while the impact strength is influenced mostly by CaCO₃ content. The elongation at break of PP/CaCO₃ composites was higher than that of PP/talc composites. The incorporation of coupling agent into PP/mineral filler composites increased the mechanical properties. Rheological properties indicated that the complex viscosity and storage modulus of talc filled samples were higher than those of calcium carbonate filled samples while the tan δ was lower. The rheological properties of hybrid‐filler filled sample were more affected by the talc than calcium carbonate. The PP‐g‐MA increased the complex viscosity and storage modulus of both single and hybrid composites. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

多元复合高流动性聚丙烯的制备与性能

研究了滑石粉(Talc)及偶联剂用量、均聚聚丙烯(PP-H)与马来酸酐接枝物(PP-g-MAH)及PP-H对高流动性共聚聚丙烯(PP)性能的影响;比较了在填充20%Talc的共聚PP中分别添加PP-g-MAH和PP-H的复合体系力学性能及流变性能的变化规律。结果表明:钛酸酯偶联剂用量为1%(相对于Talc)时,所得Talc填充共聚PP综合性能最佳;当Talc用量大于10%时,共聚PP/Talc复合材料的拉伸强度、冲击强度、弯曲强度、熔体流动速率随Talc含量的增加而逐渐下降,弯曲模量则逐渐提高;PP-g-MAH对高流动性共聚PP的拉伸强度增强效果明显优于PP-H,PP-H则使共聚PP的熔体流动性明显下降。     

Shrinkage behavior and mechanical performances of injection molded polypropylene/talc composites

In this research, the influences of adding talc mineral particles of 10 μm particle size on the shrinkage and the mechanical properties of injection molded polypropylene (PP)/talc composites were investigated. PP has a crystalline molecular structure and hence it possesses nonisotropic shrinkage along and across the flow directions. Addition of the talc mineral filler to PP induced an isotropic shrinkage in the molded part because of the nonisotropic shape of talc particles. The results of experiments indicated that the maximum flexural strength, maximum impact strength, and isotropic shrinkage were achieved by adding 10, 20, and 30 by weight percent of talc respectively. By incorporating of 10 wt% of talc particles into the PP matrix, the tensile strength was hardly affected but the occurrence of cold drawing phenomena in the tensile test was hindered considerably. The flake‐shape structure of talc filler played an important role in determining the molded part shrinkage and mechanical properties. POLYM. ENG. SCI., 47:2124–2128, 2007. © 2007 Society of Plastics Engineers     

Statistics on the fracture strength of bamboo fibers

Tensile strength is a key mechanical property of fibers used as sustainable reinforcements for advanced fiber‐reinforced composites. This study aims to conduct experimental investigation on the fracture strength of bamboo fibers of different dimensions subjected to longitudinal tensile loading. The statistical distributions of the fracture strength in bamboo fibers are correlated with the effects of fiber length and diameter variation. These are described according to Weibull statistics, which exhibit the random nature of fiber strength. The Weibull function parameters used for strength prediction are obtained from the test specimens. A comparison of predicted results and experimental data is presented to assess the accuracy of using weak‐link scaling. Furthermore, the findings of this study also indicate that fiber strength statistics dominate size dependence of tensile strength. POLYM. COMPOS., 221–228, 2016. © 2014 Society of Plastics Engineers     

Thermal and mechanical properties of a polypropylene nanocomposite

An experimental polypropylene (PP) nanocomposite, containing approximately 4 wt % of an organophilic montmorillonite clay, was prepared and characterized, and its properties were compared with those of talc‐filled (20–40 wt %) compositions. Weight reduction, with maintained or even improved flexural and tensile moduli, especially at temperatures up to 70°C, was a major driving force behind this work. By a comparison with the analytical data from a nylon 6 (PA‐6) nanocomposite, it was found that the PP nanocomposite contained well‐dispersed, intercalated clay particles; however, X‐ray diffraction, transmission electron microscopy, dynamic mechanical analysis, and permeability measurements confirmed that exfoliation of the clay in PP was largely absent. The increased glass‐transition temperature (T_g) of a PA‐6 nanocomposite, which possessed fully exfoliated particles, indicated the molecular character of the matrix–particle interaction, whereas the PP nanocomposite exhibited simple matrix–filler interactions with no increase in T_g. The PP nanocomposite exhibited a weight reduction of approximately 12% in comparison with the 20% talc‐filled PP, while maintaining comparable stiffness. Undoubtedly, considerable advantages may be available if a fully exfoliated PP nanocomposite is fabricated; however, with the materials available, a combination of talc, or alternative reinforcements, and nanocomposite filler particles may provide optimum performance. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1639–1647, 2003     

PP/滑石粉导热绝缘复合材料的制备与性能研究

采用聚丙烯(PP)为基体,不同粒径滑石粉为填料,通过双螺杆挤出机挤出制备导热绝缘的PP滑石粉复合材料。在滑石粉用量为3O%的条件下,探讨了粒径分别为3.6,6,12,30,50 μm的滑石粉对PP猾石粉复合材料的热导率、体积电阻率、力学性能和结晶性能的影响。结果表明,随着滑石粉粒径的减小,复合材料的拉伸强度和弯曲强度呈先增大后减小的变化趋势,而其热导率则呈先减小后增大的变化趋势。填充粒径为12μm的滑石粉时,复合材料的拉伸强度和弯曲强度达到最大值,分别为29.92MPa和52.58MPa,比纯PP分别提高了5.5%和12.8%。填充粒径为50μm的滑石粉时,复合材料的热导率最大,达到0.3237W/(m*K),比纯PP提高了32.7%。填充1:l的粒径为12μm和30μm滑石粉混合物时,PP复合材料的热导率为0.3184W/(m*K),高于相应的填充单一粒径滑石粉的PP复合材料。此外,所制备的PP滑石粉复合材料的体积电阻率均大于10^8Ω*cm     

彩色填充PP油箱护罩料的研制

选用滑石粉、碳酸钙、硫酸钡、高岭土、硅灰石五种矿物填料,对比本色填充聚丙烯(PP)预混料经高速混合机混合前后的颜色变化,再经挤出造粒制得黄色填充PP材料,对比测试熔体流动速率(MFR)、力学性能、颜色、表面光泽度及热稳定性。结果表明,经高速混合机混合10 min后,填料为滑石粉、碳酸钙、硫酸钡时预混料颜色基本与混合前保持一致,填料为高岭土、硅灰石时预混料颜色明显变深、变黑;填料为硫酸钡时材料的熔体流动性能及综合力学性能更符合通用机械油箱护罩用填充PP材料的技术指标要求,MFR为37 g/10 min,拉伸强度为23.6 MPa,悬臂梁无缺口和缺口冲击强度分别为81.4 k J/m~2和9.7 k J/m~2,热变形温度为109℃;填料为碳酸钙、硫酸钡时材料颜色鲜艳,与标准色板颜色最为接近;填料为硫酸钡时具有最好的表面光泽度;滑石粉、碳酸钙、硫酸钡三者比较,当填料为硫酸钡时填充PP材料的热稳定性略好。研制的黄色填充PP材料已应用于通用机械油箱护罩。     

AC／MMA接枝天然橡胶包覆滑石粉填充PP的研究

用丙烯基氯／甲基丙烯酸甲酯（AC／MMA）二元接枝天然橡胶包覆处理滑石粉。研究了处理方法,接枝天然橡胶用量以及滑石粉填充量对低韧性PP拉伸强度和制品冲击强度的影响,并与硅烷偶联剂HK－550处理滑石粉进行了比较,结果表明,AC／MMA二元接枝天然橡胶湿法包覆滑石粉效果最好,包覆滑石粉填充PP在拉伸强度保持较高的情况下,冲击强度得到有效的提高,包覆滑石粉有效地降低了由于滑石粉填充量的增加而导致的复3合材料力学性能降低的幅度,SEM的分析表明,AC／MMA二元接枝天然橡胶包覆滑石粉增加了PP基体层的应力屈服,实现了复合材料的脆韧转变。     

Comparison of the mechanical properties and interfacial interactions between talc,kaolin, and calcium carbonate filled polypropylene composites

Three types of mineral fillers—talc, calcium carbonate (CaCO₃), and kaolin (10–40 wt % filler loadings)—were compounded with polypropylene (PP) with a twin‐screw extruder. The composites were injection‐molded, and the effects of the filler loading on the mechanical, flow, and thermal properties for the three different types of filled composites were investigated. The aim was to compare their properties and to deduce prospective filler combinations that would yield hybrid PP composites in following studies. The results showed that in most cases, the strength and stiffness of the talc‐filled PP composites was significantly higher than those of the CaCO₃‐ and kaolin‐filled PP composites. However, CaCO₃, being a nonreactive filler, increased the toughness of PP. The kaolin‐filled PP composites also showed some improvement in terms of strength and stiffness, although the increases in these properties were not as significant as those of the talc‐filled PP composites. The effects of interfacial interactions between the fillers and PP on the mechanical properties were also evaluated with semiempirical equations. The nucleating ability of all three fillers was studied with differential scanning calorimetry, and the strongest nucleating agent of the three was talc, followed by CaCO₃ and kaolin. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3315–3326, 2004     

Effect of talc on the properties of polypropylene/ethylene/propylene/diene terpolymer blends

In the present study, the effect of talc content on the mechanical, thermal, and microstructural properties of the isotactic polypropylene (i‐PP) and elastomeric ethylene/propylene/diene terpolymer (EPDM) blends were investigated. In the experimental study, five different talc concentrations, 3, 6, 9, 12, and 15 wt %, were added to i‐PP/EPDM (88/12) blends to produce ternary composites. The mechanical properties such as yield and tensile strengths, elongation at break, elasticity modulus, izod impact strength for notch tip radius of 1 mm, and hardness with and without heat treatments and thermal properties, such as melt flow index (MFI), of the ternary composites have been investigated. The annealing heat treatment was carried out at 100°C for holding time of 75 h. From the tensile test results, an increased trend for the yield and tensile strengths and elasticity modulus was seen for lower talc contents, while elongation at break showed a sharp decrease with the addition of talc. In the case of MFI, talc addition decreased the MFI of i‐PP/EPDM blends. It was concluded that, taking into consideration, mechanical properties and annealing heat treatment, heat treatment has much more effect on higher yield and tensile strengths, elongation at break, elasticity modulus, impact strength, and hardness. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3033–3039, 2006     

Tensile and compressive behavior of poly(p-phenylene benzobisthiazole) fibers

Heat treated poly(p-phenylene benzobisthiazole) (PBZT) fibers tested in tension result in two types of failure modes. In failure mode I, the fiber exhibits a relatively sharp break; mode II is characterized by significant axial fiber splitting. Approximately 20% of the fibers failed in mode II when tested at 2.54, 7.62, and 12.7 cm gage lengths. At 1.25 cm gage length all the fibers failed in mode I. Tensile strength decreased from the 1.25 to 7.62 cm gage length, but tensile strength of the fibers tested at 7.62 and 12.7 cm gage lengths were similar. The two failure mode observation is supported by the Weibull statistical distribution. Fiber tensile properties were also measured at 150°C. Axial compressive strength of the PBZT fibers as determined from the recoil test is also reported and is found to be independent of fiber tensile modulus and fiber diameter. As-received heat-treated fibers were post heat treated between 700 and 775°C. Structural changes in the fiber were studied using infrared spectroscopy, small and wide angle x-ray scattering, and swelling studies. © 1995 John Wiley & Sons, Inc.     

Influence of hybridization of glass fiber and talc on the mechanical performance of polypropylene composites

The effect of the hybridization of short glass fibers (GFs) and talc mineral filler on the tensile mechanical performance of injection‐molded propylene‐ethylene copolymer composites (PP_cop) with and without weld lines (WLs) was studied in this work. The fibrous reinforcement imparts high‐tensile stiffness and strength to the molding but originates a highly anisotropic composite. The negative effect of this anisotropy is even worse when WLs occur in the molding, as the high aspect ratio GFs tend to be oriented on the weak plane of the WL. Through hybridization of GF and talc, combined in different proportions, it is possible to obtain improved mechanical properties in comparison to the standard GF reinforced PP_cop composites. The combination of GF with talc was shown to be beneficial for the WL strength of PP_cop composites, once a synergism effect was achieved with the expected optimization of the fibers/particles packing efficiency of the hybrid reinforcement. At a given constant total reinforcement concentration, the experimental data of both tensile modulus and strength properties of the hybrid composites without WL were above the predictions derived from the estimated rule of mixtures. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization,mechanical, and fracture behavior of mullite fiber‐reinforced polypropylene nanocomposites

This study describes the reinforcement effect of surface modified mullite fibers on the crystallization, thermal stability, and mechanical properties of polypropylene (PP). The nanocomposites were developed using polypropylene‐grafted‐maleic anhydride (PP‐g‐MA) as compatibilizer with different weight ratios (0.5, 1.0, 1.5, 2.5, 5.0, and 10.0 wt %) of amine functionalized mullite fibers (AMUF) via solution blending method. Chemical grafting of AMUF with PP‐g‐MA resulted in enhanced filler dispersion in the polymer as well as effective filler‐polymer interactions. The dispersion of nanofiller in the polymer matrix was identified using scanning electron microscopy (SEM) elemental mapping and transmission electron microscopy (TEM) analysis. AMUF increased the Young's modulus of PP in the nanocomposites up to a 5 wt % filler content, however, at 10 wt % loading, a decrease in the modulus resulted due to agglomeration of AMUF. The impact strength of PP increased simultaneously with the modulus as a function of AMUF content (up to 5 wt %). The mechanical properties of PP‐AMUF nanocomposites exhibited improved thermal performance as compared to pure PP matrix, thus, confirming the overall potential of the generated composites for a variety of structural applications. The mechanical properties of 5 wt % of AMUF filled PP nanocomposite were also compared with PP nanocomposites generated with unmodified MUF and the results confirmed superior mechanical properties on incorporation of modified filler. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43725.     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Mechanical properties of talc-filled polypropylene. Influence of filler content,filler particle size and quality of dispersion

Mechanical properties of polypropylene-talc composites are measured as a function of talc concentration up to 40 wt.-%, Young's modulus of filled polypropylene shows linear increase with talc concentration up to double the value of unfilled polymer. Yield stress and Charpy notch toughness decrease with increasing talc content below matrix level at the highest filler content. Composite ultimate tensile elongation and tensile impact strength decrease sharply beginning at the lowest filler concentration. The influence of the talc particle size on the mechanical properties, especially composite toughness, mentioned above, is investigated. Four type of talc were used. Notch toughness decreases according to a linear dependence with mean size of talc particles. Evaluating impact strength possible content of agglomerates of filler and other additions is necessary to be included: tensile impact strength gives slow linear dependence with increasing content of filler particles and/or agglomerates above about 10 μm. The influence of talc particle size on the toughness of filled polypropylene becomes strong if the rubber particles are present.