End‐functional polymers,thiocarbonylthio group removal/transformation and reversible addition–fragmentation–chain transfer (RAFT) polymerization

This review focuses on processes for thiocarbonylthio group removal/transformation of polymers synthesized by radical polymerization with reversible addition‐fragmentation‐chain transfer (RAFT). A variety of processes have now been reported in this context. These include reactions with nucleophiles, radical‐induced reactions, thermolysis, electrocyclic reactions and ‘click’ processes. We also consider the use of RAFT‐synthesized polymers in the construction of block or graft copolymers, functional nanoparticles and biopolymer conjugates where transformation of the thiocarbonylthio group is an integral part of the process. This includes the use of RAFT‐synthesized polymers in other forms of radical polymerization such as atom transfer radical polymerization or nitroxide‐mediated polymerization, and the ‘switching’ of thiocarbonylthio groups to enable control over polymerization of a wider range of monomers in the RAFT process. With each process we provide information on the scope and, where known, indicate the mechanism, advantages and limitations. Copyright © 2011 Society of Chemical Industry     

Sequential flow process for the controlled polymerisation and thermolysis of RAFT-synthesised polymers

The RAFT (Reversible Addition-Fragmentation Chain Transfer) process greatly enhances the control over radical polymerisations, while leaving behind a thiocarbonylthio end-group. Thermolysis presents a convenient and efficient way of removing the thiocarbonylthio end-group from RAFT polymers, without the use of additional reagents. This paper describes a simple two-step flow process for the synthesis of RAFT polymers followed by the subsequent removal of the RAFT end-group via thermolysis, without the need for isolating intermediates. A range of different polymers based on styrene, acrylates, methacrylates and acrylamides were synthesised with different RAFT agents and successfully tested for thermolysis at temperatures between 220 and 250 °C in a stainless steel tube flow reactor, resulting in complete removal of thiocarbonylthio end-groups.     

Advances in RAFT polymerization: the synthesis of polymers with defined end-groups

This paper provides an overview and discusses some recent developments in radical polymerization with reversible addition-fragmentation chain transfer (RAFT polymerization). Guidelines for the selection of RAFT agents are presented. The utility of the RAFT process is then illustrated with several examples of the synthesis of polymers with reactive end-groups. Thus, RAFT polymerization with appropriately designed trithiocarbonate RAFT agents is successfully applied to the synthesis of narrow polydispersity carboxy-functional poly(methyl methacrylate) and primary amino-functional polystyrene. Methods for removing the thiocarbonylthio end-group by aminolysis, reduction and thermal elimination are discussed. It is shown that the thiocarbonylthio end-group can be cleanly cleaved by radical induced reduction with tri-n-butylstannane, to leave a saturated chain end, or by thermolysis, to leave an unsaturated chain end.     

A 20th anniversary perspective on the life of RAFT (RAFT coming of age)

RAFT (reversible addition–fragmentation chain transfer) polymerization, making use of thiocarbonylthio transfer agents, was announced to the world just over 21 years ago. RAFT arose out of a desire to achieve perfection in polymers (or at least to define and limit the imperfections) and to invent living radical polymerization. However, living radical polymerization cannot be and never was. This perspective looks at RAFT after 21 years of development. Is RAFT a mature technology? We briefly summarize areas of current interest focusing on what is happening at CSIRO and point to where RAFT is going in areas such as RAFT free from exogenous initiators (photoRAFT, PET‐RAFT, eRAFT), new RAFT agents, RAFT for sequence‐defined polymers and RAFT single unit monomer insertion, RAFT emulsion polymerization and RAFT polymerization‐induced self‐assembly (PISA), RAFT‐crosslinking polymerization and the industrial applications of RAFT. © 2019 Society of Chemical Industry     

RAFT (Reversible addition–fragmentation chain transfer) crosslinking (co)polymerization of multi‐olefinic monomers to form polymer networks

The use of reversible addition–fragmentation chain transfer (RAFT) crosslinking (co)polymerization of multi‐olefinic monomers to produce three‐dimensional polymer networks is reviewed. We give specific attention to differences between RAFT and conventional processes, differences between RAFT and other forms of reversible deactivation radical polymerization (such as atom transfer radical and nitroxide‐mediated polymerizations) and the dependence of the polymerization process and network properties on RAFT agent structure. This knowledge is important in network optimization for applications as dynamic covalent polymers (in self‐healing polymers), as porous polymer monoliths or gels (used as chromatographic media, flow reactors, controlled release media, drug delivery vehicles and in molecular imprinting) and as coatings. © 2014 Society of Chemical Industry     

Synthesis and characterization of main‐chain,second‐order,nonlinear optical polyurethanes with isolation moieties and zigzag structures

In this study, two main‐chain second‐order nonlinear optical (NLO) polyurethanes were successfully prepared with indole‐based chromophores. The introduced phenyl isolation group and the continuous zigzag polymer backbone were found to be helpful for effectively decreasing the intermolecular dipole–dipole interactions and enhancing the NLO properties of the resulting polymers. The studied polymers exhibited good optical transparency, high thermal stability, and excellent NLO effects; this indicated that the nonlinearity–stability trade‐off and nonlinearity–transparency trade‐off could be alleviated by this newly designed polymer system. Poly{4‐anilinocarbonyl[N‐ethoxyl‐5‐phenyl‐3‐azo(2′‐oxyethylene‐4′‐nitrobenzene)indole]carbonylimino} with a zigzag backbone showed a large second harmonic generation coefficient (d₃₃) value of 88.4 pm/V. However, poly{5‐naphthyliminocarbonyl[N‐ethoxyl‐5‐phenyl‐3‐azo(2′‐oxyethylene‐4′‐nitrobenzene)indole]carbonylimino} (PUAZN) with a continuous zigzag structure exhibited a higher d₃₃ value of 116.2 pm/V, which was attributed to the unique rigid and zigzag linkage of 1,5‐naphthalene as the isolation spacer. The enhanced NLO efficiency and relatively longer term temporal stability made PUAZN as a promising candidate for practical applications in photonic devices. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42974.     

Star graft copolymer via grafting‐onto strategy using a comb!ination of reversible addition–fragmentation chain transfer arm‐first technique and aldehyde–aminooxy click reaction

A facile synthetic pathway to a multi‐arm star graft polymer has been developed via a grafting‐onto strategy using a combination of a reversible addition–fragmentation chain transfer (RAFT) arm‐first technique and aldehyde–aminooxy click reaction. A star backbone bearing aldehyde groups was prepared by the RAFT copolymerization of acrolein (Ac), an existing commercial aldehyde‐bearing monomer, with styrene (St), followed by crosslinking of the resultant poly(St‐co‐Ac) macro‐RAFT agent using divinylbenzene. The aldehyde groups on the star backbone were then used as clickable sites to attach poly(ethylene glycol) (PEG) side chains via the click reaction between the aldehyde groups and aminooxy‐terminated PEG, leading to a structurally well‐defined star graft copolymer with arms consisting of poly(St‐co‐Ac) as backbone and PEG as side chains. Crystalline morphology and self‐assembly in water of the obtained star graft copolymer were also investigated. Opportunities are open for the star graft copolymer to form either multimolecular micelles or unimolecular micelles via control of the number of grafted PEG side chains. © 2013 Society of Chemical Industry     

Investigation of liquid crystalline and photocrosslinkable poly[4‐x‐phenyl‐4′‐(m‐methacryloyloxyalkyloxy)cinnamate]s

Three series of liquid‐crystalline‐cum‐photocrosslinkable polymers were synthesized from 4‐x‐phenyl‐4′‐(m‐methacryloyloxyalkyloxy)cinnamates (x = ? H, ? OCH₃ and ? CN; m = 6, 8 and 10) by free radical solution polymerization using azobisisobutyronitrile as an initiator in tetrahydrofuran at 60 °C. All the monomers and polymers were characterized using intrinsic viscosity, and FTIR, ¹H NMR and ¹³C NMR spectroscopy. The liquid crystalline behavior of these polymers was examined using a hot stage optical polarizing microscope. All the polymers exhibited liquid crystalline behavior. The hexamethylene spacer‐containing polymers exhibited grainy textures; in contrast, the octamethylene and decamethylene spacer‐containing polymers showed nematic textures. Differential scanning calorimetry data confirmed the liquid crystalline property of the polymers. Thermogravimetric analysis revealed that all the polymers were stable between 236 and 344 °C in nitrogen atmosphere and underwent degradation thereafter. As the methylene chain length increases in the polymer side‐chain, the thermal stability and char yield of the polymers decrease. The photocrosslinking property of the polymers was investigated using the technique of exposing the polymer solution to UV light and using UV spectroscopy. The crosslinking reaction proceeds via 2π–2π cycloaddition reactions of the ? CH?CH? of the pendant cinnamate ester. The polymers containing electron‐releasing substituents (? OCH₃) showed faster crosslinking than the unsubstituted polymers and those containing electron‐withdrawing substituents (? CN). Copyright © 2007 Society of Chemical Industry     

Versatile method via reversible addition‐fragmentation transfer polymerization for synthesis of poly styrene/ZnO–nanocomposite

Reversible addition‐fragmentation chain transfer (RAFT) polymerization enables the synthesis of controlled architectures for a wide‐variety of polymers with defined end and pendant functionalities using mild conditions. A simple synthetic route for the preparation of polystyrene (PS)/ZnO nanocomposite with well‐defined structure is demonstrated. ZnO nanoparticles were synthesized by homogeneous precipitation. To reduce the aggregation among ZnO nanoparticles, an effective surface modification method was proposed by grafting polystyrene onto the ZnO particles. The surface of ZnO nanoparticles was firstly treated with a 4‐cyano‐4‐[(4‐methoxyphenyl carbon thiol) solfanylvaleric acid] coupling RAFT agent in the presence of THF as a solvent at 65°C. A carboxylic group in raft agent attached to ZnO nanoparticles by the esterification reaction with the hydroxyl groups on the ZnO particle surface. Then, RAFT polymerization of styrene was subsequently conducted to graft PS onto the exterior surface of ZnO nanoparticles by new RAFT agent 4‐cyano‐4‐[(4‐methoxyphenyl carbon thiol) solfanylvaleric acid]. The obtained nanocomposite was characterized by Fourier transform infrared spectroscopy (FT‐IR), thermo gravimetric (TGA), transmission electron microscopy (TEM), and X‐ray powder diffraction (XRD). POLYM. ENG. SCI., 56:187–195, 2016. © 2015 Society of Plastics Engineers     

Crosslinkable poly(lactic acid)‐based materials: Biomass‐derived solution for barrier coatings

The demand for biobased barrier packaging alternatives is constantly growing. Poly(lactic acid) (PLA)‐based polymers are one of the most extensively studied biomass‐derived synthetic polymers; however, they typically lack water‐barrier properties. We synthesized a copolymer of d ,l ‐lactic acid, 1,4‐butanediol, and itaconic acid [poly(d ,l ‐lactic acid–1,4‐butanediol–itaconic acid) (PLABDIA)] via bulk polycondensation. The radical crosslinking reactions of the synthesized polymer were investigated with bulk crosslinking trials to find a formulation that was suitable for a rapidly crosslinkable barrier coating. The crosslinking efficiency was tested with methacrylate and acrylate crosslinkers together with peroxide radical initiators. Poly(ethylene glycol) diacrylate (number‐average molecular weight = 250 g/mol) together with dilauroyl peroxide proved to be the best crosslinker–initiator combination. An aqueous dispersion of PLABDIA was prepared with a thermomechanical method and applied to commercial boxboard on a pilot‐scale line coater. With a coating weight of 10 g/m², a water vapor transmission rate of 22.8 g/m²d was achieved, and this coating outperformed commercial extruded PLA coatings. The samples also showed very good grease resistance and would, therefore, be a good solution for the packaging of dry and fatty goods. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44326.     

Bioerodible hydrogels based on 2‐hydroxyethyl methacrylate: Synthesis and characterization

Biocompatible polymers with specific shape and tailored hydrogel properties were obtained by polymerization of mixtures of 2‐hydroxyethyl methacrylate (HEMA) with 1–8 wt % ethylene glycol dimethacrylate (EGDMA) or tetra(ethylene glycol) diacrylate (TEGDA) as crosslinking agents, by using a redox initiator. Introduction of charged positive and negative groups was easily achieved by direct polymerization of appropriate monomer mixtures and by chemical transformation of preformed hydrogels. Investigation of the swelling behavior of the prepared hydrogels evidenced an appreciable dependence on both solvent type and polymer chemical structure. Additionally, the solvation process resulted in being controlled by solvent diffusion, according to a Fickian II mechanism. The presence of several types of water with different melting behavior was observed in fully swollen hydrogels. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2729–2741, 2002     

Synthesis and characterization of cross‐linkable poly(phthalazinone ether ketone)s

A novel class of crosslinkable poly(phthalazinone ether ketone)s with relative high molecular‐weight and good solubility were successfully synthesized by the copolymerization of bisphthalazinone containing monomer, 3,3′‐diallyl‐4,4′‐dihydroxybiphenyl and 4,4′‐di‐ fluorobenzophenone. The synthesized polymers with inherent viscosities in the range of 0.42 to 0.75 dL/g can form flexible and transparent membranes by casting from their solution. The crosslinking reaction of these polymers can be carried out by thermally curing of the virgin polymers in or without the presence of crosslinking agent. The experimental results demonstrated that the crosslinking reaction also occurred to some extent during the polymerization. The crosslinked polymers exhibited equivalent glass transition temperature (T_g) at lower crosslinking density, and showed higher T_g than virgin polymers at higher crosslinking density. The crosslinked high‐temperature polymer can be used as the base material for high temperature adhesive, coating, enamel material, and composite matrices. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Kinetics of UV‐initiated RAFT crosslinking polymerization of dimethacrylates

The UV‐initiated RAFT polymerizations of a series of poly(ethylene glycol) dimethacrylates (PEGDMA) were investigated using differential scanning photocalorimetry (DPC) at room temperature. The rate of the RAFT system was much lower than that of a conventional free radical polymerization. A mild autoacceleration occurred as the addition reaction became diffusion controlled. The influence of the spacer length (CH₂CH₂O)_x between the vinyl moieties of the dimethacrylates on the polymerization kinetics was examined. The polymerization rate of PEGDMA decreased with an increased x value from 4 to 9, but it increased with a further increased x value from 9 to 14. Mechanical properties of the resulting polymers were also examined by dynamic mechanical analysis (DMA). It was concluded that the presence of the RAFT agent during polymerization of multifunctional monomers did not have an effect on the heterogeneity of the polymer network. In comparison with three different PEGDMAs, the PEGDMA with the longest spacer formed the most homogeneous networks with a lower crosslinking density. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Emulsion of polyurethane having thermosetting properties. II. Relation between the mechanical properties of film and the polyurethane structure

A self-emulsifiable polyurethane emulsion having thermosetting property was prepared by the following procedure: the polyurethane–urea–amine was first prepared by the reaction of diethylene–triamine with a prepolymer containing terminal isocyanate groups in a ketone solvent, and then the primary amino group in the polyurethane–urea–amine was reacted with epichlorohydrin. The mixture was neutralized with an aqueous acid, and finally the ketone solvent was removed by distillation in vacuo. In the polyurethane, polytetramethylene glycol (PTMG) was the base polymer functioning as the soft segment. The present paper reports the effects of the following variables on the mechanical properties of the film prepared from the polyurethane emulsion, i.e., the M _n of PTMG, the molar ratio of diethylene–triamine (DTA) to prepolymer containing terminal isocyanate groups, the structure of the isocyanate end group and the molar ratio of tolylene diisocyanate (TDI) with PTMG. The best elastomer property was realized when M_n of PTMG was 2000, TDI/PTMG molar ratio was 2.0, and prepolymer/DTA molar ratio was 0.85.     

Mechanical properties and morphology of poly(ethylene glycol)‐side‐chain‐modified bismaleimide polymer

Two maleimido‐end‐capped poly(ethylene glycol) (m‐PEG)‐modified bismaleimide (BMI) resins [4,4′‐bismaleimido diphenylmethane (BDM)] were synthesized from poly(ethylene glycol) (PEG) of two different molecular weights. A series of m‐PEGs and unmodified BDM were blended and thermally cured. The effect of incorporating m‐PEG side chains on the morphology and mechanical behaviors of BMI polymer were evaluated. The mechanical properties of these m‐PEG‐modified BMIs that were evaluated included flexural modulus, flexural strength, strain at break, fracture toughness, and fracture energy. The morphology of these blends was studied with scanning electron microscopy. All the m‐PEG‐modified BMI polymers showed various degrees of phase separation depending on the molecular weights and concentrations of the m‐PEG used. The effects of these morphological changes in the m‐PEG‐modified BMI polymers were reflected by the improved fracture toughness and strain at break. However, there was a reduction in the flexural moduli in all m‐PEG‐modified BMI polymers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 715–724, 2002     

Synthesis of PEG‐functionalized poly(diphenylacetylene)s and their gas permeation properties

The polymerizations of 1‐(3‐methylphenyl)‐2‐(4‐trimethylsilyl)phenylacetylene ( 1a ) and 1‐(4‐methylphenyl)‐2‐(4‐trimethylsilyl)phenylacetylene ( 1b ) were carried out with TaCl₅‐n‐Bu₄Sn to give relatively high‐molecular‐weight polymers ( 2a and 2b ) (M_n > 5 × 10⁵). The obtained polymers were brominated by using benzoyl peroxide and N‐bromosuccinimide first, followed by substitution reaction of three types of polyethylene glycol. When diethylene glycol was used as a reagent on substitution reaction of meta‐substituted polymer, PEG‐functionalized poly(diphenylacetylene) with the highest content of oxyethylene unit [ 4a(2) ] was obtained, and the degree of substitution was 0.60. The degrees of substitution decreased to 0.15 and 0.08 when the polyethylene glycols with higher molecular weights were used. PEG‐substitution reaction to the para‐substituted polymers was difficult to proceed, and hence the degree of substitution was 0.18 even when diethylene glycol was used. The CO₂/N₂ separation factor of PEG‐functionalized polymer [ 4a(2) ] was as large as 28.8, although that of 2a was 7.41. The other PEG‐functionalized polymers also exhibited high CO₂ permselectivity, and their CO₂/N₂ separation factors were over 20. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Microwave‐assisted polymerization: Inert addition and surface coating of superabsorbent polymer for improved physical properties

Two different polymerization techniques, microwave‐assisted polymerization and free radical solution polymerization, were utilized in the syntheses of superabsorbent polymers with varying amounts of acrylic acid (31–50%). Degrees of neutralization were in the range of 68–80 mol %, and clay level was varied between 0 and 5%. The base polymer produced with microwave‐assisted polymerization had higher absorbency under low load (0.3 psi) than those with the free radical solution polymerization. To improve its absorbency under higher loads (0.6 and 0.9 psi), the surface coating step was implemented by using ethylene glycol diglycidyl ether as a surface crosslinking agent. Properties such as capacity, permeability, and absorbency under different loads were tested in 0.9% sodium chloride solution for the base and the surface‐coated polymers. In addition, extractables and residual acrylic acid were measured to determine the reaction's efficiency. In conclusion, surface coating improved polymer properties, and the incorporation of clay imparted permeability to the polymer. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43990.     

Rheology of polyacrylonitrile‐based precursor polymers produced from controlled (RAFT) and conventional polymerization: Its role in solution spinning

Polymer solutions in dimethyl sulfoxide (DMSO) as a solvent, made from reversible addition fragmentation chain transfer (RAFT)‐mediated polyacrylonitrile (RAFT^¥ PAN) terpolymer with molecular weight (MW) of 260,000 g/mol and dispersity (Ð) of 1.29, behave differently under applied shear stress than polymer solutions made from conventional PAN (Control PAN) with similar MW (258,000 g/mol) but Ð of 2.05 in the same solvent. The unique rheology of RAFT PAN is because of the reduced amount of high MW polymer fractions. Specifically, a 25% (w/v) polymer solution of RAFT PAN had a viscosity of 198 Pas while the equivalent control PAN polymer solution had a viscosity of 968 Pas at a shear rate of 1 s^?1. Also, RAFT PAN polymer solutions had a longer Newtonian plateau than control PAN polymer solutions. This exhibits more liquid character in RAFT PAN polymer solutions than control PAN polymer solutions at same temperature and concentration. In dynamic tests, RAFT PAN polymer solutions gelled slower than their equivalent control PAN polymer solutions because of their longer polymer chain relaxation times. Slow gelling and higher liquid character in RAFT PAN polymer solutions can result in obtaining stronger and finer precursor fibers during wet spinning. Since RAFT PAN polymer solutions exhibit low viscosity and higher liquid character when compared to its equivalent control PAN at same concentration and temperature, these can allow a wider working window for wet spinning and can also allow higher solid content in the polymer solutions that remain easy to wet spin. This is expected to lead to compact and finer fibers with less voids and higher strength. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44273.     

Preparation of monodisperse hydrophilic polymer microspheres with N,N′‐methylenediacrylamide as crosslinker by distillation precipitation polymerization

Highly crosslinked cauliflower‐like poly(N,N′‐methylenebisacrylamide) particles were prepared by distillation precipitation polymerization in neat acetonitrile with 2,2′‐azobisisobutyronitrile as initiator. Monodisperse hydrophilic polymer microspheres with various functional groups, such as amide, pyrrolidone and carboxylic acid, with a spherical shape and smooth surface in the size range 120–600 nm were prepared by distillation precipitation copolymerizations of functional comonomers including N‐isopropylacrylamide, N‐vinylpyrrolidone, methacrylic acid with N,N′‐methylenebisacrylamide as crosslinker. The polymer particles were formed and precipitated out from the reaction medium during the distillation of the solvent from the reaction system through an entropic precipitation manner. The effects of the solvent and the degree of crosslinking on the morphology and the loading capacity of the functional groups of the resultant polymer particles were investigated. The resulting polymer particles were characterized with scanning electron microscopy, transmission electron microscopy, dynamic light scattering and Fourier transform infrared spectroscopy. Copyright © 2007 Society of Chemical Industry     

Substituent effects on trithiocarbonates‐mediated polymerization of styrene

In the present work, the effectiveness of five trithiocarbonates (TTCs) as mediating agents in the reversible addition fragmentation chain transfer (RAFT) polymerization and photopolymerization of styrene (St) were investigated. The five TTCs including S,S′‐bis(α, α′‐dimethyl‐α″‐acetic acid) trithiocarbonate (TTC1), bis(2‐oxo‐2‐phenyl‐ethyl) trithiocarbonate (TTC2), 3‐(2‐carboxyethylsulfanylthiocarbonylsulfanyl)‐propionic acid (TTC3), 2‐(2‐carboxyethylsulfanylthiocarbonylsulfanyl)propionic acid (TTC4), and 2‐(2‐carboxyethylsulfanylthiocarbonylsulfanyl)‐2‐methylpropionic acid (TTC5) were synthesized, in which the substitution patterns (groups Z and R) of the TTCs were varied. The dynamic behavior of TTC1, TTC2, TTC4, and TTC5‐mediated polymerization of St was well described by pseudo first‐order kinetics. In the presence of TTC1, TTC2, TTC4, and TTC5, the polydispersity indices changed with increasing conversion in the range of 1.10–1.25 typical for RAFT‐prepared (co)polymers, and were well below the theoretical lower limit of 1.50 for a normal free radical polymerization. Transfer coefficients of TTCs in St polymerization at 70°C were estimated by using the Mayo method. Density functional theory calculations successfully predicted the effect of the structure of TTCs on the activity of RAFT agents in a qualitative manner. The calculated results for RAFT agents agreed well with the experimental results. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009