Swelling properties of chemically modified oil palm empty fruit bunch based polyurethane composites

In this study, the diffusion of various types of solvent in oil palm empty fruit bunch/polyurethane composites, produced from chemically modified empty fruit bunches, was investigated. The solubility parameters and polymer–solvent interaction parameters of the produced composites were determined. The void contents of the composites were also determined before swelling tests to eliminate the free solvent present in the system. From the results obtained, we found that the diffusion of the solvents was dependent on the compatible group available and the voids present in the system. The solubility parameters of the empty fruit bunch/polyurethane composites with different degrees of chemical modification were 11.6 and 11.7 (cal/cm^?3)^1/2. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Bamboo fiber reinforced polypropylene composites and their mechanical,thermal, and morphological properties

Short bamboo fiber reinforced polypropylene composites were prepared by incorporation of various loadings of chemically modified bamboo fibers. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as compatibilizer to improve fiber–matrix adhesion. The effects of bamboo fiber loading and modification of the resin on the physical, mechanical, thermal, and morphological properties of the bamboo reinforced modified PP composites were studied. Scanning electron microscopy studies of the composites were carried out on the interface and fractured surfaces. Thermogravimetric analysis and IR spectroscopy were also carried out. At 50% volume fraction of the extracted bamboo fiber in the composites, considerable increase in mechanical properties like impact, flexural, tensile, and thermal behavior like heat deflection temperature were observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of fiber‐surface treatment on the properties of hybrid composites prepared from oil palm empty fruit bunch fibers,glass fibers,and recycled polypropylene

In this article, we report the effects of hybridization and fiber‐surface modification on the properties of hybrid composites prepared from recycled polypropylene (RPP), coupling agents, oil palm empty fruit bunch (EFB), and glass fibers through a twin‐screw extruder and an injection‐molding machine. The surface of the EFB fibers was modified with different concentrations (10–15 wt %) and temperatures (60–90°C) of alkali solutions. The structure and morphology of the fibers were observed with the help of Fourier transform infrared spectroscopy and scanning electron microscopy. Different types of composites were fabricated with untreated, alkali‐treated, and heat‐alkali‐treated fibers. Comparative analysis of the mechanical, structural, morphological, and thermal properties of the composites was carried out to reveal the effects of treatment and hybridization. The analysis results reveal that composites prepared from the alkali‐treated (in the presence of heat) fibers show improved mechanical, thermal, and morphological properties with a remarkably reduced water absorption. Additionally, the crystallinity of RPP also increased with the development of biaxial crystals. The improvement of various properties in relation to the structures and morphologies of the composites is discussed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43049.     

Thermal and mechanical properties of injection moulded heat-treated oil palm empty fruit bunch fibre-reinforced high-density polyethylene composites

ABSTRACT

Oil palm empty fruit bunch (OPEFB) was heat treated at 180°C using a vacuum oven for one hour, extruded and compounded with high-density polyethylene at 10%, 20% and 30% weight fraction. The composites then were injection moulded into dumb-bell shaped specimens. The effect of composition and heat treatment on the thermal properties of composites were investigated using Thermogravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC). The tensile and flexural properties were also tested using an Instron Universal Testing Machine. TGA shows an increase in the degradation peak temperature of the heat-treated composites. DSC revealed an increasing trend in the degree of crystallinity (X_c) of the matrix as the heat-treated empty fruit bunch was used as a filler. An increment in the tensile modulus and tensile strain were observed for the treated fibre composites. In addition, the tensile strength value was increased for treated fibre composites with lower fibre loading.     

Effects of poly(dimethyl siloxane) on the water absorption and natural degradation of poly(lactic acid)/oil‐palm empty‐fruit‐bunch fiber biocomposites

Composites were fabricated with poly(lactic acid) and oil‐palm empty‐fruit‐bunch (EFB) fibers with extrusion; this was followed by an injection‐molding technique. Before compounding, the surface of the fiber was modified through ultrasound and poly(dimethyl siloxane) (PDMS). The influences of the ultrasound and PDMS on the water absorption and biodegradability of the composites were investigated. Additionally, the composites were buried under soil for 6 months, and their biodegradability was assessed through different characterization techniques, such as tensile testing and weight loss and diffussability measurement. The changes on the surface of the fibers due to treatment were examined by scanning electron microscopy analysis, and the influences on the biodegradability of the composites were observed. Functional group analysis and possible changes before and after degradation were also examined by a Fourier transform infrared spectrophotometric technique. The results analyses revealed that the treatment of fibers improved the density of the fibers and reduced the water uptake of the composites. The overall weight loss due to soil burial testing was found to be maximum for the untreated‐fiber‐based composites (6.8%), whereas the ultrasound‐ and silane‐treated composites showed the minimum value of weight loss (3.7%). The deterioration of the tensile strength due to degradation was found to be at a maximum for the untreated‐fiber‐based composite (27%), whereas the ultrasound‐ and silane‐treated‐fiber‐based composites showed a minimum value of 8%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42784.     

Mechanical properties of polypropylene composite reinforced with oil palm empty fruit bunch pulp

In this study, oil palm empty fruit bunch (EFB) pulp was used as reinforcing agent in polypropylene composite. EFB pulp was prepared using soda pulping with different concentrations of sodium hydroxide (NaOH) solution. Overall, the tensile and flexural properties specifically the strength and the toughness showed improvement as the NaOH content in the treatment was increased. This was attributed to lower probability for EFB pulp to agglomerate and the production of higher aspect ratio pulp fibers. Scanning electron microscopy analysis showed evidence of the reduction in EFB bundles diameter after NaOH treatment. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of varying fiber lengths on mechanical,thermal, and morphological properties of MA‐g‐PP compatibilized and chemically modified short pineapple leaf fiber reinforced polypropylene composites

Environmentally benign, low cost and abundantly available short pineapple leaf fibers (PALF), found mostly in the Tropical rain forest climates are ideal materials for manufacture of thermoplastic polymer‐matrix composites. Here, mechanical and thermal properties of composites of maleic anhydride grafted polypropylene (MA‐g‐PP) and chemically modified short PALF are studied as a function of different fiber lengths at 10 vol % fibers loading with fiber orientation in the longitudinal direction. The effects of fiber lengths and fiber loading on the morphological properties are assessed via observations by scanning electron microscopy. Fiber length of 6 mm oriented longitudinally at 10 vol % fibers loading in PP is the optimum and recommended composition, where 73% increase in impact properties, 37% increase in the flexural modulus, 33% increase in flexural strength, and 14% increase in vicat softening temperature are observed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradable composites: Morphological,chemical, thermal,and mechanical properties of composites of poly(hydroxybutyrate‐co‐hydroxyvalerate) with curaua fibers after exposure to simulated soil

Composites produced from biodegradable polymeric matrixes reinforced with vegetable fibers have attractive mechanical properties and are environmentally friendly. This work is directed to the biodegradation of a composite made of a poly(hydroxybutyrate‐co‐hydroxyvalerate) matrix reinforced with curaua fibers (with and without alkaline treatment) in simulated soil. The composites were developed by extrusion and injection and were later buried in simulated soil according to the ASTM G160‐03 method. Scanning electron microscopy showed evidence of microbial attack on the samples surfaces. Infrared spectra showed that the composites biodegradation was mainly caused by erosion of the surface layer resulting from microorganisms activity. Thermogravimetric analysis pointed out reduced thermal stability of the samples, and results of differential scanning calorimetry showed that the degree of crystallinity increases and then decreases progressively throughout the degradation period, indicating that enzymatic degradation primarily occurs in the amorphous phase material and thereafter in the crystalline phase. For curaua composite fibers, reductions in tensile strength and elastic modulus are more significant, indicating that the presence of fibers promotes biodegradation of the curaua fiber. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40712.     

A review on oil palm empty fruit bunch fiber‐reinforced polymer composite materials

Natural fiber‐reinforced polymer composite materials have emerged in a wide spectrum of area of the polymer science. The composite produced from these types of materials are low density, low cost, comparable specific properties, and most importantly they are environmental friendly. The composite materials produced from oil palm fibers and commercially available polymers have offered some specific properties that can be comparable to conventional synthetic fiber composite materials. However, these properties are greatly dependent on the compatibility of oil palm fibers and matrix phase with moisture absorption as one of the critical issues that becomes the drawbacks of the oil palm fiber polymer composite materials. Apparently, it greatly affects the physical as well as mechanical properties of the composite materials. The present review reports the work on oil palm empty fruit bunch (OPEFB) fiber‐reinforced polymer composites with some interest on the OPEFB physical structure, and chemical compositions. Finally, the incorporation of OPEFB into polymeric materials leads to several interesting consequences on the water absorption characteristics and the mechanical properties, which have been reviewed. POLYM. COMPOS., 31:2079–2101, 2010. © 2010 Society of Plastics Engineers     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

An investigation of sound absorption coefficient on sisal fiber poly lactic acid bio‐composites

In this research, the mechanical, acoustical, thermal, morphological, and infrared spectral properties of untreated, heat and alkaline‐treated sisal fiber‐reinforced poly‐lactic‐acid bio‐composites were analyzed. The bio‐composite samples were fabricated using a hot press molding machine. The properties mentioned above were evaluated and compared with heat‐treated and alkaline‐treated sisal fibers. Composites with heat‐treated sisal fibers were found to exhibit the best mechanical properties. Thermo‐gravimetric analysis (TGA) was conducted to study the thermal degradation of the bio‐composite samples. It was discovered that the PLA‐sisal composites with optimal heat‐treated at 160°C and alkaline‐treated fibers possess good thermal stability as compared with untreated fiber. The results indicated that the composites prepared with 30wt % of sisal had the highest sound absorption as compared with other composites. Evidence of the successful reaction of sodium hydroxide and heat treatment of the sisal fibers was provided by the infrared spectrum and implied by decreased bands at certain wavenumbers. Observations based on scanning electron microscopy of the fracture surface of the composites showed the effect of alkaline and heat treatment on the fiber surface and improved fiber‐matrix adhesion. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42470.     

Bleached extruder chemi‐mechanical pulp fiber‐PLA composites: Comparison of mechanical,thermal, and rheological properties with those of wood flour‐PLA bio‐composites

An environmentally friendly bleached extruder chemi‐mechanical pulp fiber or wood flour was melt compounded with poly(lactic acid) (PLA) into a biocomposite and hot compression molded. The mechanical, thermal, and rheological properties were determined. The chemical composition, scanning electron microscopy, and Fourier transform infrared spectroscopy results showed that the hemicellulose in the pulp fiber raw material was almost completely removed after the pulp treatment. The mechanical tests indicated that the pulp fiber increased the tensile and flexural moduli and decreased the tensile, flexural, and impact strengths of the biocomposites. However, pulp fiber strongly reinforced the PLA matrix because the mechanical properties of pulp fiber‐PLA composites (especially the tensile and flexural strengths) were better than those of wood flour‐PLA composites. Differential scanning calorimetry analysis confirmed that both pulp fiber and wood flour accelerated the cold crystallization rate and increased the degree of crystallinity of PLA, and that this effect was greater with 40% pulp fiber. The addition of pulp fiber and wood flour modified the rheological behavior because the composite viscosity increased in the presence of fibers and decreased as the test frequency increased. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44241.     

The effect of various anhydride modifications on mechanical properties and water absorption of oil palm empty fruit bunches reinforced polyester composites

The chemical modification of oil palm empty fruit bunches (EFB) using non‐catalysed reaction with acetic, propionic and succinic anhydrides were investigated. Proof of modification was indicated by the increase of weight and was confirmed by Fourier‐transform infrared analysis (FT‐IR). The mechanical and water‐absorption properties of all anhydride‐modified EFB composites were evaluated at different volume fractions (V_f). The properties were improved for these modified fibres, whereas unmodified EFB fibres exhibited poor mechanical properties and higher water absorption. Acetic anhydride modification showed the greatest benefit on composite properties, followed by propionic and succinic anhydride modification. © 2001 Society of Chemical Industry     

Fabrication of the self‐reinforced composites using co‐extrusion technique

The results of this work relate to the use of co‐extrusion technology in the preparation of monocomposite pellets. The low‐melting polypropylene copolymer was used as a matrix material. The high strength polypropylene fibers were used as a fibrous reinforcement. Research confirms the possibility to produce the pellets with fibrous structure. The prepared composite material in the form of pellets was processed and shaped using the injection molding technology. Obtained samples were subjected to mechanical testing in the static tensile test and dynamic mechanical analysis. Research complements microscopic observation of scanning electron microscopy. The measurement results confirm the reinforcing effect of the fibers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41180.     

Effect of fiber treatments on mechanical properties of coir or oil palm fiber reinforced polyester composites

The use of plant fibers as a reinforcement in polyester matrices requires the issue of compatibility between the two phases to be addressed. Because plant fibers present hydrophilic surfaces and polyesters are generally hydrophobic, poor fiber–matrix dispersion and wetting of the fibers by the matrix may result. As a consequence, the mechanical properties of the composite are severely reduced. This study considers the effect of fiber treatment by chemical modification of the fibers (acetylation) or the use of silane or titanate coupling agents on the mechanical properties of coir or oil palm reinforced polyester composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1685–1697, 2000     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

Characteristics of murta bast fiber reinforced epoxy composites

The growing global concern over environment protection has led to the application of natural fiber reinforced polymer composites as alternative materials in manufacturing sectors. Various natural fibers are therefore being explored for reinforcement of polymer matrices. In the present work, murta bast fibers of varying length and weight percent are mixed randomly with the epoxy matrix and the composites are prepared from these mixtures by using the hand lay‐up method. The composites are characterized on the basis of density, thermal gravimetric analysis, infrared spectroscopy, scanning electron microscopy, tensile strength, flexural strength, compressive strength, impact strength, and Rockwell hardness studies. Tensile, flexural, and compressive moduli of the composites are also determined. The tensile strength of the composite was analyzed in the light of the different analytical models. Composites containing 30 weight % fibers of length 25 or 35 mm have the optimum mechanical properties. Murta bast fiber has the characteristics to become a good natural material for reinforcement. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44142.     

Mechanical,morphological, and thermal properties of nanotalc reinforced PA6/SEBS‐g‐MA composites

Ternary butylene‐styrene‐g‐maleic anhydride (SEBS‐g‐MA) (100/20 w/w) blend with varying content of nanotalc (1, 3, and 5 wt %) were prepared by melt compounding followed by injection molding. Thermal properties were investigated by thermogravimetric analysis (TGA) and the results show that the thermal properties of nanocomposites are slightly improved by the addition of nanotalc content. The morphology of nanocomposites using wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) revealed the delamination of talc layers in the ternary nanocomposites. The dynamic mechanical properties of the samples were analyzed by using dynamic mechanical thermal analyzer (DMTA). The results show that the storage modulus of the blend monotonically increased while tan δ curve show the diffuse pattern with the nanotalc content. The mechanical properties of PA6/SEBS‐g‐MA nanocomposites were studied by tensile, flexural, and impact tests. The tensile and flexural properties continuously increased while izod impact and elongation‐at‐break decreased with nanotalc content. Various theoretical predictive models were used to correlate tensile modulus with the experimental data. The experimental data shows the positive deviation with the applied models. Bela Pukanszky model has been used to calculate the value of parameter B by employing tensile strength data. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41381.     

Influence of processing on morphology in short aramid fiber reinforced elastomer compounds

The rubber industry is nowadays facing the general increase of raw materials as the customers are confronted with rising prices for energy. Therefore there is a need for higher durability of elastomer applications. Short fiber reinforced elastomers can contribute to the improvement of dynamic and wear properties. To determine structure–property relationships in short fiber reinforced elastomer compounds it is of crucial interest to know the contributions of fiber aspect ratio, volume content, orientation and fiber–elastomer interaction. Therefore the influence of different processing conditions and fiber contents on the resulting morphology and macroscopic properties was investigated in this article by the help of fluorescence and confocal laser microscopy using a transparent ethylene‐propylene‐diene rubber (EPDM) matrix. It was found that the processing induced fiber breakage was the key factor in determining the composite morphology and subsequent physical properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1682–1690, 2013     

Simultaneous enhancements in the mechanical,thermal, and electrical performances of glass‐fiber‐reinforced cyanate ester/epoxy composites with plasma‐functionalized carbon nanotubes at different temperatures

Woven glass‐fiber‐reinforced cyanate ester/epoxy composites modified with plasma‐functionalized multiwalled carbon nanotubes (MWCNTs) were prepared. The mechanical, thermal, and electrical properties of the composites were investigated at different temperatures. The results show that the interlaminar shear strength, thermal conductivity, and electrical conductivity of the composites at room temperature and the cryogenic temperatures were enhanced simultaneously by the incorporation of MWCNTs, whereas the nonconductive behavior of the composites as electrical insulating materials was not changed. Meanwhile, the reinforcing mechanism was also examined on the basis of the microstructure of the composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41418.