Studies on the solvent extraction of rare earths from nitrate media with a combination of di‐(2‐ethylhexyl)phosphoric acid and sec‐octylphenoxyacetic acid

BACKGROUND: Di‐(2‐ethylhexyl)phosphoric acid (D2EHPA, H₂A₂) has been used extensively in hydrometallurgy for the extraction of rare earths, but it has some limitations. Synergistic extraction has attracted much attention because of its enhanced extractabilities and selectivities. In the present study, sec‐octylphenoxyacetic acid (CA12, H₂B₂) was added into D2EHPA systems for the extraction and separation of rare earths. The extraction mechanism of lanthanum with the mixtures and the separation of lanthanoids and yttrium were investigated. RESULTS: The synergistic enhancement coefficient for La³⁺ extracted with D2EHPA + CA12 was calculated as 3.63. La³⁺ was extracted as La(NO₃)₂H₂A₂B with the mixture. The logarithm of the equilibrium constant was determined as 0.80. The thermodynamic functions, ΔH, ΔG, and ΔS were calculated to be 4.03 kJ mol^?1, ? 1.96 kJ mol^?1, and 20.46 J mol^?1 K^?1, respectively. The mixtures have synergistic effects on Ce³⁺, Nd³⁺, and Y³⁺, with an especially strong synergistic effect on Y³⁺. Neither synergistic nor antagonistic effects on Dy³⁺ and weak antagonistic effects on Lu³⁺ were found. CONCLUSION: Mixtures of D2EHPA and CA12 exhibit evident synergistic effects when used to extract La³⁺ from nitric solution. The stoichiometries of the extracted complexes have been determined by graphical and numerical methods to be La(NO₃)₂H₂A₂B with the mixture. The extraction is an endothermic process. The mixture exhibits different extraction effects on rare earths, which provides possibilities for the separation of Y³⁺ from Ln³⁺ at a proper ratio of D2EHPA and CA12. Copyright © 2008 Society of Chemical Industry     

Synergistic extraction and separation study of rare earth elements from nitrate medium by mixtures of sec‐nonylphenoxy acetic acid and 2,2′‐bipyridyl

BACKGROUND: Synergistic extraction has been proven to enhance extractability and selectivity. Numerous types of synergistic extraction systems have been applied to rare earth elements, among which sec‐nonylphenoxyacetic acid (CA100) has proved to be an excellent synergistic extractant. In this study, the synergistic enhancement of the extraction of holmium(III) from nitrate medium by mixtures of CA100 (H₂A₂) with 2,2′‐bipyridyl (bipy, B) in n‐heptane has been investigated. The extraction of all other lanthanides (except polonium) and yttrium by the mixtures in n‐heptane has also been studied. RESULTS: Mixtures of CA100 and bipy have significant synergistic effects on all rare earth elements, for example holmium(III) is extracted as Ho(NO₃)₂HA₂B with the mixture instead of HoH₂A₅, which is extracted by CA100 alone. The thermodynamic functions, ΔH^o, ΔG^o, and ΔS^o have been calculated as 2.96 kJ mol^?1, ? 6.23 kJ mol^?1, and 31.34 J mol^?1 K^?1, respectively. CONCLUSION: Methods of slope analysis and constant molar ratio have been successfully applied to study the synergistic extraction stoichiometries of holmium(III) by mixtures of CA100 and bipy. Mixtures of these extractants have also shown various synergistic effects with other rare earth elements, making it possible to separate them. Thus CA100 + bipy may be used to separate yttrium from other lanthanides at appropriate ratios of the extractants. Copyright © 2011 Society of Chemical Industry     

Extraction and separation of rare earths from chloride medium with mixtures of 2‐ethylhexylphosphonic acid mono‐(2‐ethylhexyl) ester and sec‐nonylphenoxy acetic acid

BACKGROUND: 2‐ethylhexylphosphonic acid mono‐(2‐ethylhexyl) ester (HEHEHP, H₂A₂) has been applied extensively to the extraction of rare earths. However, there are some limitations to its further utilization and the synergistic extraction of rare earths with mixtures of HEHEHP and another extractant has attracted much attention. Organic carboxylic acids are also a type of extractant employed for the extraction of rare earths, e.g. naphthenic acid has been widely used to separate yttrium from rare earths. Compared with naphthenic acid, sec‐nonylphenoxy acetic acid (CA100, H₂B₂) has many advantages such as stable composition, low solubility, and strong acidity in the aqueous phase. In the present study, the extraction of rare earths with mixtures of HEHEHP and CA100 has been investigated. The separation of the rare earth elements is also studied. RESULTS: The synergistic enhancement coefficient decreases with increasing atomic number of the lanthanoid. A significant synergistic effect is found for the extraction of La³⁺ as the complex LaH₂ClA₂B₂ with mixtures of HEHEHP and CA100. The equilibrium constant and thermodynamic functions obtained from the experimental results are 10^?0.92 (K_AB), 13.23 kJ mol^?1 (ΔH), 5.25 kJ mol^?1 (ΔG), and 26.75 J mol^?1 K^?1 (ΔS), respectively. CONCLUSION: Graphical and numerical methods have been successfully employed to determine the stoichiometries for the extraction of La³⁺ with mixtures of HEHEHP and CA100. The mixtures have different extraction effects on different rare earths, which provides the possibility for the separation of yttrium from heavy rare earths at an appropriate ratio of HEHEHP and CA100. Copyright © 2009 Society of Chemical Industry     

Synergistic extraction of rare earths(III) from chloride medium with mixtures of 1‐phenyl‐3‐methyl‐4‐benzoyl‐pyrazalone‐5 and di‐(2‐ethylhexyl)‐2‐ethylhexylphosphonate

The synergistic effect of 1‐phenyl‐3‐methyl‐4‐benzoyl‐pyrazalone‐5 (HPMBP, HA) and di‐(2‐ethylhexyl)‐2‐ethylhexylphosphonate (DEHEHP, B) in the extraction of rare earths (RE) from chloride solutions has been investigated. Under the experimental conditions used, there was no detectable extraction when DEHEHP was used as a single extractant while the amount of RE(III) extracted by HPMBP alone was also low. But mixtures of the two extractants at a certain ratio had very high extractability for all the RE(III). For example, the synergistic enhancement coefficient was calculated to be 9.35 for Y³⁺, and taking Yb³⁺ and Y³⁺ as examples, RE³⁺ is extracted as RE(OH)A₂.B. The stoichiometry, extraction constants and thermodynamic functions such as Gibbs free energy change ΔG (?17.06 kJ mol^?1), enthalpy change ΔH (?35.08 kJ mol^?1) and entropy change ΔS (?60.47 J K^?1 mol^?1) for Y³⁺ at 298 K were determined. The separation factors (SF) for adjacent pairs of rare earths were calculated. Studies show that the binary extraction system not only enhances the extraction efficiency of RE(III) but also improves the selectivity, especially between La(III) and the other rare earth elements. Copyright © 2006 Society of Chemical Industry     

Syntheses and adsorption properties for Hg2+ of chelating resin of crosslinked polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole

A novel chelating resin with functional group containing S and N atoms was prepared using chloromethylated polystyrene and 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT) as materials. Its structure was characterized by infrared spectra and elementary analysis. The results showed that the content of the functional group was 2.07 mmol BMT g^?1 resin, 47% of which were in the form of monosubstitution (PS‐BMT‐1) and 53% in the form of double substitution (PS‐BMT‐2). The adsorption for mercury ion was investigated. The adsorption dynamics showed that the adsorption was controlled by liquid film diffusion. Increasing the temperature was beneficial to adsorption. The Langmuir model was much better than the Freundlich model to describe the isothermal process. The adsorption activation energy (E_a), ΔG, ΔH, and ΔS values calculated were 18.56 kJ·mol^?1, ‐5.99 kJ·mol^?1, 16.38 kJ·mol^?1, and 37.36, J·mol^?1·K^?1, respectively. The chelating resin could be easily regenerated by 2% thiourea in 0.1 mol·L^?1 HCl with higher effectiveness. Five adsorption–desorption cycles demonstrated that this resin was suitable for repeated use without considerable change in adsorption capacity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1646–1652, 2004     

Synthesis and biological activity of phthalimide‐based polymers containing 5‐fluorouracil

The attachment of anticancer agents to polymers is a promising approach towards reducing the toxic side‐effects and retaining the potent antitumour activity of these agents. A new tetrahydrophthalimido monomer containing 5‐fluorouracil (ETPFU) and its homopolymer and copolymers with acrylic acid (AA) and with vinyl acetate (VAc) have been synthesized and spectroscopically characterized. The ETPFU contents in poly(ETPFU‐co‐AA) and poly(ETPFU‐co‐VAc) obtained by elemental analysis were 21 mol% and 20 mol%, respectively. The average molecular weights of the polymers determined by gel permeation chromatography were as follows: M_n = 8900 g mol^?1, M_w = 13 300 g mol^?1, M_w/M_n = 1.5 for poly(ETPFU); M_n = 13 500 g mol^?1, M_w = 16 600 g mol^?1, M_w/M_n = 1.2 for poly(ETPFU‐co‐AA); M_n = 8300 g mol^?1, M_w = 11 600 g mol^?1, M_w/M_n = 1.4 poly(ETPFU‐co‐VAc). The in vitro cytotoxicity of the compounds against FM3A and U937 cancer cell lines increased in the following order: ETPFU > 5‐FU > poly(ETPFU) > poly(ETPFU‐co‐AA) > poly(ETPFU‐co‐VAc). The in vivo antitumour activities of all the polymers in Balb/C mice bearing the sarcoma 180 tumour cell line were greater than those of 5‐FU and monomer at the highest dose (800 mg kg^?1). © 2002 Society of Chemical Industry     

Solvent extraction of rare earths from chloride medium with mixtures of 1-phenyl-3-methyl-4-benzoyl-pyrazalone-5 and sec-octylphenoxyacetic acid

In the present study, the extraction of rare earths with mixtures of 1-phenyl-3-methyl-4-benzoyl-pyrazalone-5 (HPMBP, HA) and sec-octylphenoxyacetic acid (CA12, H₂B₂) in benzene has been studied from chloride medium. The synergistic enhancement coefficient decreases with increasing atomic numbers of rare earths. The synergistic extraction of lanthanum and neodymium has been studied with the methods of slope analysis and constant mole. The extracted complexes are determined as LaH₂ClA₂B₂ and NdH₃ClA₃B₂, respectively. The equilibrium constants, formation constants, and the thermodynamic functions are calculated. Furthermore, the different extraction effects on rare earths have been employed to discuss the possibilities for the separation of rare earths.     

Synthesis and biological activity of medium range molecular weight polymers containing exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid

A new monomer, exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid (ETCA), was prepared by reaction of maleimidocaproic acid and furan. The homopolymer of ETCA and its copolymers with acrylic acid (AA) or with vinyl acetate (VAc) were obtained by photopolymerizations using 2,2‐dimethoxy‐2‐phenylacetophenone as an initiator at 25 °C. The synthesized ETCA and its polymers were identified by FTIR, ¹H NMR and ¹³C NMR spectroscopies. The apparent average molecular weights and polydispersity indices determined by gel permeation chromatography (GPC) were as follows: M_n = 9600 g mol^?1, M_w = 9800 g mol^?1, M_w/M_n = 1.1 for poly(ETCA); M_n = 14 300 g mol^?1, M_w = 16 200 g mol^?1, M_w/M_n = 1.2 for poly(ETCA‐co‐AA); M_n = 17 900 g mol^?1, M_w = 18 300 g mol^?1, M_w/M_n = 1.1 for poly(ETCA‐co‐VAc). The in vitro cytotoxicity of the synthesized compounds against mouse mammary carcinoma and human histiocytic lymphoma cancer cell lines decreased in the following order: 5‐fluorouracil (5‐FU) ≥ ETCA > polymers. The in vivo antitumour activity of the polymers against Balb/C mice bearing sarcoma 180 tumour cells was greater than that of 5‐FU at all doses tested. © 2001 Society of Chemical Industry     

Solvent extraction and separation of rare earths from chloride media using α-aminophosphonic acid extractant HEHAMP

Solvent extraction and separation of rare earths (REs: La ~ Lu, plus Y and Sc) by a novel synthesized extractant, (2-ethylhexylamino)methyl phosphonic acid mono-2-ethylhexyl ester (HEHAMP, abbreviated as H₂A₂), were investigated in chloride medium. The favorable separation factors (SFs) between adjacent heavy REs suggested that HEHAMP has a better separation performance than P507. The extracted complex of trivalent REs was determined to be REClH₂A₄ by the slope analysis method. Thermodynamic parameters (ΔH, ΔG, and ΔS) of Lu were calculated as 7.47 kJ mol^?1, ?6.05 kJ mol^?1, and 45.4 J mol^?1 K^?1 at 298.15 K, respectively, which indicate that the extraction reaction of Lu is an endothermic process. The loading capacity of 30% (v/v) HEHAMP toward Lu(III), Yb(III), and Y(III) was about 15.17 g Lu₂O₃/L, 14.46 g Yb₂O₃/L, and 12.64 g Y₂O₃/L, respectively. HCl is the most efficient stripping acid, and 92% of the loaded Yb(III) can be stripped by one-stage stripping with 2 mol/L HCl.     

Adsorptive removal of anionic and non‐ionic surfactants from aqueous phase using Posidonia oceanica (L.) marine biomass

BACKGROUND: In this study, the capability of low‐cost, renewable and abundant marine biomass Posidonia oceanica (L.) for adsorptive removal of anionic and non‐ionic surfactants from aqueous solutions have been carried out in batch mode. Several experimental key parameters were investigated including exposure time, pH, temperature and initial surfactant concentration. RESULTS: It was found that the highest surfactant adsorption capacities reached at 30 °C were determined as 2.77 mg g^?1 for anionic NaDBS and as 1.81 mg g^?1 for non‐ionic TX‐100, both at pH 2. The biosorption process was revealed as a thermo‐dependent phenomenon. Equilibrium data were well described by the Langmuir isotherm model, suggesting therefore a homogeneous sorption surface with active sites of similar affinities. The thermodynamic constants of the adsorption process (i.e. ΔG°, ΔH° and ΔS°) were respectively evaluated as ? 8.28 kJ mol^?1, 48.07 kJ mol^?1 and ? 42.38 J mol^?1 K^?1 for NaDBS and ? 9.67 kJ mol^?1, 95.13 kJ mol^?1 and ? 174.09 J mol^?1 K^?1 for TX‐100. CONCLUSION: Based on this research, valorization of highly available Posidonia oceanica biomass, as biological adsorbent to remove anionic and non‐ionic surfactants, seems to be a promising technique, since the sorption systems studied were found to be favourable, endothermic and spontaneous. Copyright © 2007 Society of Chemical Industry     

Kinetic study of ytterbium(III) extraction from sulfate medium with Cyanex 923

The kinetics of ytterbium(III) extraction from sulfate medium with Cyanex 923 in heptane has been investigated with a constant interfacial cell with laminar flow, which aimed to identify the extraction regime, reaction zone and rate equations. It was found that the extraction rate of ytterbium(III) increased linearly with stirring speed and specific interfacial area. The activation energy E_a (9.56 kJ mol^?1), activation enthalpy ΔH^± (7.05 kJ mol^?1), activation entropy ΔS^±₂₉₈ (?0.31 kJ mol^?1) and Gibbs free energy of activation ΔG^±₂₉₈ (98.3 kJ mol^?1) were calculated from the dependence of extraction rate on temperature. The experiential rate equations were obtained by investigating the influence of the concentration of various species on the extraction rate. A diffusion regime has been deduced from evidence of the linear dependence of extraction rate on stirring speed and the low value of the activation energy. The liquid–liquid interface is most probably the reaction zone in view of the linear dependence of extraction rate on specific interfacial area, the high interfacial activity and low water‐solubility of extractant. Thus the mass transfer rate is controlled by interfacial film diffusion of species. Copyright © 2007 Society of Chemical Industry     

Polystyrene composites of single‐walled carbon nanotubes‐graft‐polystyrene

Single‐walled carbon nanotubes (SWCNTs) dispersed in N‐methylpyrrolidone (NMP) were functionalized by addition of polystyryl radicals from 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐ended polystyrene (SWCNT‐g‐PS). The amount of polystyrene grafted to the nanotubes was in the range 20‐25 wt% irrespective of polystyrene number‐average molecular weight ranging from 2270 to 49 500 g mol^?1. In Raman spectra the ratios of D‐band to G‐band intensity were similar for all of the polystyrene‐grafted samples and for the starting SWCNTs. Numerous near‐infrared electronic transitions of the SWCNTs were retained after polymer grafting. Transmission electron microscopy images showed bundles of SWCNT‐g‐PS of various diameters with some of the polystyrene clumped on the bundle surfaces. Composites of SWCNT‐g‐PS in a commercial‐grade polystyrene were prepared by precipitation of mixtures of the components from NMP into water, i.e. the coagulation method of preparation. Electrical conductivities of the composites were about 10^?15 S cm^?1 and showed no percolation threshold with increasing SWCNT content. The glass transition temperature (T_g) of the composites increased at low filler loadings and remained constant with further nanotube addition irrespective of the length and number of grafted polystyrene chains. The change of heat capacity (ΔC_p) at T_g decreased with increasing amount of SWCNT‐g‐PS of 2850 g mol^?1, but ΔC_p changed very little with the amount of SWCNT‐g‐PS of higher molecular weight. The expected monotonic decrease in ΔC_p coupled with the plateau behavior of T_g suggests there is a limit to the amount that T_g of the matrix polymer can increase with increasing amount of nanotube filler. Copyright © 2012 Society of Chemical Industry     

Studies on two‐dimensional coordination polymer cadmium phosphate and its high efficient adsorption of Pb(II) ions from aqueous solutions

The two‐dimensional coordination polymer cadmium phosphate with the morphology of rectangle layers was prepared by solid‐state template reaction at room temperature, and was characterized by XRD, FTIR, and TEM techniques. The as‐synthesized sample is a layered cadmium phosphate material, in which the structure is poly (CdPO₄^?) anion framework with ammonium ions and water species residing in the space between the layers, and cadmium ions are coordinated by the phosphate oxygen atoms. This article also presents the adsorption of Pb(II) ions from aqueous solution on the as‐synthesized coordination polymer cadmium phosphate, and the results showed that this inorganic polymer adsorbent had good adsorption capacity. It could reach to the saturation adsorption capacity within an hour, and its excellent adsorption capacity for Pb(II) was 5.50 mmol/g when the initial solution concentration was 1.68 × 10³ μg/mL at T = 278K. Moreover, the adsorption kinetics and adsorption isotherms were studied, it revealed that the adsorption kinetics can be modeled by pseudo second‐order rate equation wonderfully. The apparent activation energy (E_a), ΔG, ΔH, and ΔS were 3.16 kJ mol^?1, ?13.97 kJ mol^?1, ?11.84 kJ mol^?1, and 7.66 J mol^?1 K^?1, respectively. And it was found that Langmuir equation could well interpret the adsorption of the as‐synthesized coordination polymer cadmium phosphate for Pb(II) ions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solubility of polystyrene with various molecular weights in subcritical 1,1,1,2‐tetrafluoroethane: experiment and modified model

The solubility of polystyrene with molecular weight of 100 000 and 260 000 g mol^?1 was measured at temperatures from 313 to 333 K and at pressures from 5.0 to 13.0 MPa in subcritical 1,1,1,2‐tetrafluoroethane (R134a). The effects of pressure, temperature and molecular weight on the solubility of polystyrene were investigated. Meanwhile, the solubility of polystyrene was correlated using six density‐based semi‐empirical models (Chrastil, A‐L, K‐J, S‐S, M‐S‐T and Bartle). The M‐S‐T model was used to verify the self‐consistency of the experimental data, and the enthalpy values of polystyrene, including ΔH_total, ΔH_sub and ΔH_sol, were estimated through the Chrastil and Bartle models. In addition, a modified M‐S‐T model was proposed through a detailed study of semi‐empirical model formulas and verified by the solubility of polystyrene in subcritical R134a and 38 other solid solutes in supercritical carbon dioxide and subcritical R134a. © 2018 Society of Chemical Industry     

Syntheses and characterization of polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole and its sorption behavior for Pd(II), Pt(IV), and Au(III)

A type of chelating resin crosslinking polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT), containing sulfur and nitrogen atoms, was prepared. The structure of PS‐BMT was confirmed by FTIR, elemental analysis, and X‐ray photoelectron spectroscopy (XPS). Adsorption of Pd(II), Pt(IV), and Au(III) was investigated. The capacity of PS‐BMT to adsorb Pd(II) and Pt(IV) was 0.190 and 0.033 mmol/g, respectively. The adsorption dynamics of Pd(II) showed that adsorption was controlled by liquid film diffusion and that the apparent activation energy, E_a, was 32.67 kJ/mol. The Langmuir model was better than the Freundlich model in describing the isothermal process of Pd(II), and the ΔG, ΔH, and ΔS values calculated were ?0.33 kJ/mol, 26.29 kJ/mol, and 87.95 J mol^?1 K^?1, respectively. The mechanisms of adsorption of Pd(II), Pt(IV), and Au(III) were confirmed by XPS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 631–637, 2006     

Time‐resolved small‐angle X‐ray scattering study of void fraction evolution in high‐density polyethylene during stress unloading and strain recovery

By means of time‐resolved small‐angle X‐ray scattering, we developed an analysis methodology to assess the void volume fraction ?_v in high‐density polyethylene (HDPE) during tensile testing. The specimens were first drawn up to different imposed strains, and subsequently were subjected to stress unloading and strain recovery stages. During the loading stage, ?_v progressively increased with the strain level, starting from a well‐defined onset strain prior to the yield point. In particular, ?_v reached a maximum of 8.75 vol% for a strain of 12.5% in the case of a HDPE grade with a molecular weight of 105 000 g mol^?1. Stress unloading and strain recovery caused a decrease in ?_v attained at the end of the loading stage. For a HDPE grade with a molecular weight of 55 000 g mol^?1, ?_v was more important during the loading stage and the decrease in ?_v was less marked during the stress unloading stage when compared to the HDPE with molecular weight of 105 000 g mol^?1. The residual and reversible components of void volume fraction were revealed. © 2015 Society of Chemical Industry     

Synthesis,characterization, conductivity,band gap,and kinetic of thermal degradation of poly‐4‐[(2‐mercaptophenyl) imino methyl] phenol

The oxidative polycondensation reaction conditions of 4‐[(2‐mercaptophenyl) imino methyl] phenol (2‐MPIMP) were studied in an aqueous acidic medium between 40 and 90°C by using oxidants such as air, H₂O₂, and NaOCl. The structures of the synthesized monomer and polymer were confirmed by FTIR, ¹H NMR, ¹³C NMR, and elemental analysis. The characterization was made by TGA‐DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly‐4‐[(2‐mercaptophenyl) imino methyl]phenol (P‐2‐MPIMP) was found to be 92% for NaOCl oxidant, 84% for H₂O₂ oxidant 54% for air oxidant. According to the SEC analysis, the number‐average molecular weight (M_n), weight‐average molecular weight (M_w), and polydispersity index values of P‐2‐MPIMP were found to be 1700 g mol^?1, 1900 g mol^?1, and 1.118, using H₂O₂; 3100 g mol^?1, 3400 g mol^?1, and 1.097, using air; and 6750 g mol^?1, 6900 g mol^?1, and 1.022, using NaOCl, respectively. According to TG analysis, the weight losses of 2‐MPIMP and P‐2‐MPIMP were found to be 95.93% and 76.41% at 1000°C, respectively. P‐2‐MPIMP showed higher stability against thermal decomposition. Also, electrical conductivity of the P‐2‐MPIMP was measured, showing that the polymer is a typical semiconductor. The highest occupied molecular orbital, the lowest unoccupied molecular orbital, and the electrochemical energy gaps (E′_g) of 2‐MPIMP and P‐2‐MPIMP were found to be ?6.13, ?6.09; ?2.65, ?2.67; and 3.48, 3.42 eV, respectively. Kinetic and thermodynamic parameters of these compounds investigated by MacCallum‐Tanner and van Krevelen methods. The values of the apparent activation energies of thermal decomposition (E_a), the reaction order (n), pre‐exponential factor (A), the entropy change (ΔS*), enthalpy change (ΔH*), and free energy change (ΔG*) were calculated from the TGA curves of compounds. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of poly(styrene‐b‐2‐hydroxyethyl acrylate) block copolymer using reverse iodine transfer polymerization

Reverse iodine transfer polymerizations (RITP) of 2‐h‐ydroxyethyl acrylate (HEA) were performed in N,N‐dimethylformamide at 75°C using AIBN as initiator. Poly(2‐hydroxyethyl acrylate) (PHEA) with M_n = 3300 g mol^?1 and M_w/M_n <1.5 were obtained. Homopolymerization of styrene in RITP was also carried out under similar conditions using toluene as solvent. The resulting iodo‐polystyrene (PS‐I) with (M_{n, SEC} = 607 g mol^?1, polydispersity index (PDI) = 1.31) was used as a macroinitiator for the synthesis of amphiphilic block copolymers based on HEA with controlled well‐defined structure. Poly(styrene‐b‐2‐hydroxyethyl acrylate) (PS‐b‐PHEA) with M_n = 13,000 g mol^?1 and polydispersity index (M_w/M_n) = 1.4 was obtained, copolymer composition was characterized using ¹H‐NMR and FTIR, whereas SEC and gradient HPLC were used to confirm the formation of block copolymer and the living character of polymer chains. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Structural and Preliminary Explosive Property Characterizations of New 3,4,5‐Triamino‐1,2,4‐triazolium (Guanazinium) Salts

Two new highly stable energetic salts were synthesized in reasonable yield by using the high nitrogen‐content heterocycle 3,4,5‐triamino‐1,2,4‐triazole and resulting in its picrate and azotetrazolate salts. 3,4,5‐Triamino‐1,2,4‐triazolium picrate (1) and bis(3,4,5‐triamino‐1,2,4‐triazolium) 5,5′‐azotetrazolate (2) were characterized analytically and spectroscopically. X‐ray diffraction studies revealed that protonation takes place on the nitrogen N1 (crystallographically labelled as N2). The sensitivity of the compounds to shock and friction was also determined by standard BAM tests revealing a low sensitivity for both. B3LYP/6–31G(d, p) density functional (DFT) calculations were carried out to determine the enthalpy of combustion (Δ_cH (1) =−3737.8 kJ mol⁻¹, Δ_cH (2) =−4577.8 kJ mol⁻¹) and the standard enthalpy of formation (Δ_fH° (1) =−498.3 kJ mol⁻¹, (Δ_fH° (2) =+524.2 kJ mol⁻¹). The detonation pressures (P (1) =189×10⁸ Pa, P (2) =199×10⁸ Pa) and detonation velocities (D (1) =7015 m s⁻¹, D (2) =7683 m s⁻¹) were calculated using the program EXPLO5.