Electrochemical corrosion behavior of biomedical Ti–22Nb and Ti–22Nb–6Zr alloys in saline medium

The aims of this study were to investigate the effects of Zr addition and potentiodynamic polarization on the microstructure and corrosion resistance of Ti–22Nb and Ti–22Nb–6Zr alloy samples. The corrosion tests were carried out in 0.9% NaCl at 37 °C and neutral pH value, utilizing the OCP, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. The results of XRD and optical microscopy indicated that the addition of Zr stabilized the β phase, which plays a crucial role in the corrosion resistance improvement of the Ti–22Nb–6Zr alloy. From the polarization curves, it can be seen that the alloys exhibited a wide passive region without the breakdown of the passive films and also low corrosion current densities. In addition, the values of the corrosion current densities and passive current densities decreased with the addition of 6 at% Zr into the Ti–22Nb alloy. The EIS results of these two alloy samples after 1‐h immersion in 0.9% NaCl solution, and being fitted by R_S(Q_PR_P) model, suggested that the corrosion resistance of the passive films improved with the addition of Zr and only a single passive film formed on the surfaces. However, two time constants were observed for the Ti–22Nb and Ti–22Nb–6Zr alloy samples after potentiodynamic polarization, the spectra of which can be fitted using the R_s(Q_o(R_o(Q_bR_b))) model. In addition, the corrosion resistance of the two alloy samples was reinforced significantly because of polarization when compared to the immersed samples. All these observations suggested a nobler electrochemical behavior of the titanium alloys with the addition of Zr element and after polarization.     

Electrochemical corrosion behaviors and protective properties of Ni–Co–TiO2 composite coating prepared on sintered NdFeB magnet

In this paper, a protective Ni–Co–TiO₂ composite coating was prepared on the sintered NdFeB magnet by direct current electrodeposition. The surface morphologies, microstructure, and chemical composition of the composite coating were studied using scanning electron microscope (SEM), X‐ray diffraction (XRD), and energy dispersive spectroscopy (EDS), respectively. The surface morphologies and microstructure analysis showed that the composite coating possessed cauliflower‐like grain colonies, and formed face‐centered cubic (fcc) solid solution. The electrochemical corrosion behaviors of the composite coating in 0.5 mol/L H₂SO₄, 0.6 mol/L NaOH, 0.6 mol/L Na₂SO₄, and neutral 3.5 wt% NaCl solutions were evaluated by potentiodynamic polarization measurements and electrochemical impedance spectroscopy (EIS), showing good protection for NdFeB magnet. In order to further investigate the protective properties of the composite coating for NdFeB magnet and the practicability of the composite coating, the long‐term immersion test was carried out in neutral 3.5 wt% NaCl solutions using EIS. The results of long‐term corrosion test showed that the Ni–Co–TiO₂ composite coating could provide long‐term protection in neutral 3.5 wt% NaCl solutions for NdFeB magnet.     

Impedance spectroscopy studies of electroless Ni–P matrix,Ni–W–P,Ni–P–ZrO2, and Ni–W–P–ZrO2 coatings exposed to 3.5% NaCl solution

Ni–P matrix, ternary Ni–W–P and Ni–P–ZrO₂ coatings, and quaternary Ni–W–P–ZrO₂ coatings were deposited using electroless method from a glycine bath. Their corrosion resistance was evaluated by electrochemical impedance spectroscopy (EIS) for various immersion times in a 3.5% NaCl solution. From among the investigated coatings, the ternary Ni–W–P coatings show the highest resistance to corrosion in the first hour of exposure to the 3.5% NaCl medium. An addition of ZrO₂ adversely affects the performance of both the Ni–P coatings and the Ni–W–P coatings. For all the coatings, including the ones containing tungsten, a marked decrease in pore resistance (R_por) over time is observed. This means that their corrosion resistance and capacity to protect the substrate decline. On the other hand, after 24 h immersion in the 3.5% NaCl solution the Ni–W–P coating shows the highest low‐frequency impedance modulus (|Z|_{f = 0.01 Hz}). As regards corrosion resistance, the Ni–P coatings and the Ni–W–P coatings perform best.     

Corrosion electrochemical behaviors of silane coating coated magnesium alloy in NaCl solution containing cerium nitrate

Sol–gel coatings cannot provide adequate corrosion protection for metal/alloys in the corrosive environments due to their high crack‐forming potential. This paper demonstrates the possibility to employ cerium nitrate as inhibitor to decrease the corrosion development of sol–gel‐based silane coating on the magnesium alloy in NaCl solution. Cerium nitrate was added into the NaCl solution where the silane coating coated magnesium alloy was immersed. Scanning electron microcopy (SEM) was used to examine surface morphology of the silane coating coated magnesium alloy immersed in NaCl solutions doped and undoped with cerium nitrate. The corrosion electrochemical behaviors were investigated using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests. The results showed that the introduction of cerium nitrate into NaCl solution could effectively inhibit the corrosion of the silane coating coated magnesium alloy. Moreover, the influence of concentration of cerium nitrate on the corrosion inhibition and the possible inhibiting mechanism were also discussed in detail.     

The effect of calcination on the corrosion performance of TiO2 sol–gel coatings doped with benzotriazole on steel CK45

Sol–gel method under dip coating process and tetra‐n‐butyle orthotitanate as precursor were used to produce titanium oxide coating on steel CK45. The effect of calcination at 400 °C, after drying at 120 °C, on the morphology and corrosion performance of the coatings was investigated. Benzotriazole (BTA) as an inhibitor was doped on titanium oxide coatings to improve corrosion performance of the coatings as well as its self‐healing properties. The morphology and structure of the coatings were studied by X‐ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersive X‐ray spectroscopy (EDS) techniques. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques were used to study the corrosion behavior of the coatings. The results revealed that after calcination the dominant crystalline phase was anatase. The results obtained from potentiodynamic polarization curves and electrochemical impedance spectra showed that the calcinated and doped with BTA coatings possessed higher corrosion resistance than non‐calcinated although doped with BTA coatings.     

Research on intercrystalline corrosion,exfoliation corrosion,and stress corrosion cracking of Al–Zn–Mg–Sc–Zr alloy

The intercrystalline corrosion, exfoliation corrosion (EXCO), and stress corrosion cracking (SCC) of Al–Zn–Mg–Sc–Zr alloy were investigated by means of constant temperature immersion corrosion method, optical microscopy, transmission electron microscopy (TEM), and electrochemical impedance spectroscopy (EIS). The results show that intercrystalline corrosion, and EXCO susceptibility of Al–Zn–Mg–Sc–Zr alloy decrease gradually with increasing of aging time. Corrosion susceptibility order from low to high is as follows: OA > PA > UA > NA. The SCC susceptibility index of PA temper is more than OA temper at the same strain rate. According to TEM observation, with aging time prolonging, a part of η′ phases transform to η equilibrium phases, which become coarse gradually. The distribution discontinuity of the grain boundary precipitates increases. In addition, for Al–Zn–Mg–Sc–Zr alloy without EXCO, the EIS is comprised by a capacitive impedance arc at high frequency and an inductive impedance arc at low frequency. Once EXCO occurs, the EIS is composed of two capacitive impedance arcs at high frequency and at low frequency, respectively.     

Corrosion characterization of microarc oxidation coatings formed on Mg–7Li alloy

Ceramic coatings with thickness of 27 µm were fabricated on Mg–7Li alloy in Na₂SiO₃–C₆H₁₈O₂₄P₆ solution by microarc oxidation (MAO). The morphology and phase composition of MAO coatings were characterized by scanning electron microscopy (SEM) and X‐ray diffraction (XRD). The corrosion behavior of the bare and MAO coated Mg–7Li alloy was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). Results showed that the MAO coatings were composed of MgO, Li₂O, and Mg₂SiO₄, and there existed some micropores on the coating surface with a diameter of 3–20 µm. The corrosion potential (E_corr) and corrosion current density (I_corr) of the MAO coated alloy were about ?1.4761 V and 7.204 × 10^?7 A/cm², respectively. The E_corr of the MAO coated alloy increased by 109.6 mV and its I_corr decreased by three orders compared with that of the bare Mg–7Li alloy. The EIS plots indicated that the impedance of the MAO coated alloy was 15 times higher than that of the bare alloy. The fitting parameters showed that the resistance of the MAO coatings was far greater than that of the bare alloy. The dense intermediate layer and the transition layer of the MAO coatings acted as a barrier to hinder the proceeding of solution permeation, remarkably improving the corrosion resistance of the Mg–7Li alloy.     

Influence of SiC + WC addition to Cr(VI) bath on corrosion behaviour of coatings in sulphate solution

Abstract

Cr–WC–SiC coatings were deposited from Cr(VI) baths containing a mixture of both WC and SiC particles in the ratio of 1 : 1. X-ray photoelectron spectroscopy data indicated relatively low percentages of both WC (about 2˙68–2˙85 at.-% of W4f) and SiC (0˙16–0˙45 at.-% of Si2p) particles in the top layers of the Cr–WC–SiC coatings. However, these particles have some effect on the morphology and corrosion properties of the Cr coating. Protective properties of the coatings obtained were studied at different exposure times of samples in sulphate solution (pH=2˙8), using the electrochemical impedance spectroscopy method (EIS). Equivalent circuits, based on the electrophysical model describing the electrochemical corrosion at the coated surface, were proposed. The simulation of EIS data with the proposed equivalent circuit models made it possible to reveal the details of the corrosion processes occurring at coated systems (steel/Cr–WC–SiC coatings) immersed in the sulphate solution. Based on EIS data, diffusion in the coating was found to be a significantly controlling factor in the corrosion process for the system under investigation. The electrochemical impedance spectroscopy tests indicated a better corrosion resistance of Cr–WC–SiC coating than that of Cr. Analysis of the EIS data suggests that the enhanced corrosion resistance of Cr–WC–SiC coating was due to the microstructural features of these coatings, presumably containing smaller pores than Cr coating.     

电弧喷涂Al-Zn-Si-RE合金涂层在3.5%NaCl溶液中的电化学腐蚀行为(英文)

采用电弧喷涂方法在低碳钢表面获得高铝含量的Al-Zn-Si-RE涂层。通过测量Al-Zn-Si-RE涂层在3.5%NaCl溶液中的动电位极化曲线,腐蚀电位-时间曲线和电化学阻抗谱,系统地研究涂层的电化学腐蚀行为。通过将测量电化学阻抗谱拟合成等效电路图,研究涂层在3.5%NaCl溶液中浸泡不同时间的阻抗行为。结果表明:Al-Zn-Si-RE涂层与Zn-15Al涂层具有相似的极化行为,阳极极化曲线均无钝化特征,仅呈现出活性溶解,但其腐蚀性能优于Zn-15Al涂层。Al-Zn-Si-RE涂层可以给钢基体提供有效的牺牲阳极保护作用,且牺牲阳极保护作用在涂层腐蚀过程中占主导地位。此外,腐蚀电位-时间曲线和电化学阻抗谱结果表明:在浸泡过程中存在点蚀-溶解-再沉积、活化溶解、阴极保护、腐蚀产物引起的物理屏蔽和涂层失效五个腐蚀阶段。     

Initial corrosion protection of Zn–Mn alloys electrodeposited from alkaline solution

The effects of a deposition current density (c.d.) on the corrosion behaviour of Zn–Mn alloy coatings, deposited from alkaline pyrophosphate solution, were investigated by atomic absorption spectrophotometry (AAS), X-ray diffraction (XRD), atomic force microscopy (AFM), optical microscopy, electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential (E_corr). XRD analysis disclosed that zinc hydroxide chloride was the main corrosion product on Zn–Mn coatings immersed in 0.5 mol dm⁻³ NaCl solution. EIS investigations revealed that less porous protective layer was produced on the alloy coating deposited at c.d. of 30 mA cm⁻² as compared to that deposited at 80 mA cm⁻².     

Comparative investigation on copper atmospheric corrosion by electrochemical impedance and electrical resistance sensors

Electrochemical impedance (EIS) and thin electrical resistance (ER) sensors were invented for atmospheric corrosion measurement of copper (Cu) during cyclic wetting–drying/high–low temperature tests and field exposure tests. Three-month field exposure results showed that average corrosion rate of Cu measured by ER sensor was well in accordance with that by weight loss method. During cyclic wetting–drying test, EIS was proven to reflect sensitively time of wetting and drying on the surface of sensor. Although corrosion rate obtained from EIS had a similar tendency to that obtained from ER sensors, the former was more dependent on environmental humidity than the latter. When relative humidity was low than 60%, corrosion rate of Cu measured by EIS was much lower than that by weight loss method, mainly attributing to the fact that impedance sensor failed to detect corrosion current of interlaced Cu electrodes due to the breakdown of conductive passage composed of absorbed thin liquid film under low humidity condition. Promisingly, ER sensor was proven to be more suitable for atmospheric corrosion monitoring than electrochemical techniques because it could sensitively monitor thickness loss of Cu foil according to the Ohmic law, no matter how dry or wet the sensor surface is.     

The inhibition effect of tannic acid on mild steel corrosion in seawater wet/dry cyclic conditions

The inhibition effect of tannic acid on mild steel corrosion in seawater wet/dry cyclic conditions was studied by weight loss and electrochemical methods. Result of the polarisation curves shows that corrosion current density decreases from 47.85 μA cm⁻² to 6.67 μA cm⁻² after tannic acid is added; charge transfer resistance remains stable in the electrochemical impedance spectra. Scanning electron microscopy, X-ray diffraction, and Fourier transform infrared reflection are performed to study the corrosion inhibition. The inhibition effect of the compound is attributed to ferric tannate film formation on the steel surface, which is relatively stable during wet/dry cycles.     

Corrosion behaviour of molybdate–phosphate–silicate coatings on galvanized steel

In this work, a Cr-free conversion layer based on molybdate–phosphate–silicate (MPS) was synthesised on a galvanized steel by simple immersion and its corrosion behaviour was compared to that of a typical chromate layer. Stationary electrochemical techniques and electrochemical impedance spectroscopy (EIS) were employed to highlight the corrosion mechanisms of both coatings in different NaCl concentrations, immersion times and pH. Contrary to the chromate layer, the MPS coating showed good electrochemical stability even in concentrated NaCl solutions and remarkable electrochemical efficiency. With increasing time, two corrosion stages were associated with the two likely sublayers of the MPS coating. Furthermore, the MPS coating behaved better than the chromate layer in acidic and alkaline pH, especially the latter as a compact corrosion product layer formed. Finally, each coating/electrolyte interface was characterised by an electrical equivalent circuit giving a satisfactory correlation between the experimental and the calculated impedance. It derived that the MPS could be an environmentally friendly alternative to chromating.     

Corrosion behavior of newly developed Ti–Ag–Fe dental alloys in neutral saline solution

The corrosion behavior of Ti–5Ag–xFe alloys (x = 1, 2.5, 5 wt%) in neutral saline solution was investigated by the open‐circuit potential (OCP), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and potentiostatic tests. The microstructural observation indicated that β‐Ti phase was retained by the addition of Fe into Ti–Ag alloys. Compared with commercially pure (CP) Ti, Ti–5Ag–xFe alloys exhibited higher corrosion potentials, lower current densities, and larger impedance, these suggested that Ti–5Ag–xFe alloys have nobler electrochemical corrosion behavior when compared with CP Ti in neutral saline solution.     

Microstructural characteristics and corrosion property of non‐chromate surface treatments on AZ91D magnesium alloy

Chromate conversion coatings can be successfully used for corrosion protection of magnesium alloys. However, the environmental laws have imposed severe restrictions on chromate use in many countries. In this study, a novel protective environmental‐functionally gradient coating was formed on AZ91D magnesium alloy by non‐chromate surface treatments, which consisted of pre‐etching followed by cerium‐based chemical conversion before applying the sol–gel CeO₂ film. It was determined by the analysis of X‐ray diffraction that the gradient coating was mainly composed of CeO₂. The calculation, based on the Scherrer formula, further revealed the formation of nanocrystalline structure in the coating. Scanning electron microscopy (SEM) observations showed that the coating was homogeneous and compact, no obvious cracked structure occurred. According to the immersion tests, potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) tests, the corrosion resistance of AZ91D magnesium alloy was found to be greatly improved by means of this novel environmental‐functionally gradient coating.     

Exfoliation corrosion of Al–Zn–Mg–Cu–Zr alloy containing Sc examined by electrochemical impedance spectroscopy

The exfoliation corrosion behavior of an Al–Zn–Mg–Cu–Zr alloy containing Sc artificially aged at 120 °C for 24 h is studied by macroscopic observation techniques and electrochemical impedance spectroscopy (EIS) measurements. After 48 h immersion, the blisters start bursting and delamination initiates, along with the appearance of two time constants in the impedance diagrams. According to the simulation by equivalent circuit, the corrosion rate decreases sharply and then reaches a steady state, which is due to the change of the solution pH and oxide layer thickness, as well as the accumulation of corrosion products.     

Preparation and corrosion protective properties of titania‐containing modified self‐assembled nanophase particle (TMSNAP) sol–gel on AA2024 aluminum alloy

A new method of preparing water‐based sol–gel containing titania nanoparticles for the protection of aluminum alloy AA2024 against corrosion was presented and performance of the coating in Harrison's solution was studied. The coating was prepared using alkoxysilanes, tetraethylorthosilicate (TEOS) and 3‐glycidoxypropyltrimethoxysilane (GPTMS), and in additional metal alkoxide, titanium(IV) tetrapropoxide (TPOT), as a source of titania particles. Poly(ethylene imine) (PEI) polymer was utilized to create cross‐linking and also to improve the coating quality. In addition, the molar ratios and amount of components and factors affecting performance were assessed to improve coating properties and its performance. Potentiodynamic scan (PDS) and electrochemical impedance spectroscopy (EIS) measurements were performed to evaluate the corrosion protection performance of coatings. Also, scanning electron microscopy (SEM) was employed to investigate surface morphology. The stability of the best prepared coating and its corrosion protective effects on the alloy were evaluated in Harrison's solution up to 15 days. The results revealed that this new sol–gel coating provides significant protection against corrosion of the AA2024 alloy in Harrison's solution.     

Effect of Si nanoparticles on the corrosion protection performance of organic coating on carbon steel in chloride environment

This work examines the effect of silicon (Si) nanoparticles on the corrosion protection performance of epoxy coating over carbon steel by Electrochemical Impedance Spectroscopy (EIS) and Transmission Electron Microscopy. The EIS was performed in a 0.1 M NaCl solution after a wet/dry cyclic corrosion and continuous immersion test. The addition of Si nanoparticles increased the film resistance (R_f) and the charge transfer resistance (R_ct) of the coated steel. The surface analysis showed that uniform and fine Si-Fe complex oxides layers were formed acting as barrier layers that enhanced the corrosion protection of the coated steel in the wet/dry cyclic corrosion test. The results of the EIS of the coated steel with Si nanoparticles suggested that Si nanoparticles play a beneficial role in enhancing the corrosion resistance of organic coated steel.     

Electrochemical corrosion behavior of electroless Ni–P coating in NaCl and H2SO4 solutions

Electrochemical corrosion behavior of electroless Ni–P coating in NaCl and H₂SO₄ solutions were studied by potentiodynamic polarization curves and electrochemical impedance spectra techniques, as well as the corrosion morphology was characterized. The results indicate that electroless Ni–P coating with about 25 µm is stable in 30 days immersion in NaCl solution. Although it was corroded with prolonged immersion days, the corrosive medium has not penetrated through the coating. During the H₂SO₄ concentration ranging from 5 to 10%, the corrosion current density of electroless Ni–P coating increased due to the intensified anodic dissolution process; in 15% H₂SO₄ solution, electroless Ni–P coating shows obvious anodic passivation effect.     

EIS study on 2024‐T3 aluminum alloy corrosion in simulated acid rain under cyclic wet‐dry conditions

The wet‐dry cycle corrosion processes of 2024‐T3 aluminum alloys under different pH environments were investigated using electrochemical impedance (EIS) technique in conjunction with SEM method. The results show that, during the dry period of each cycle, the electrode potential was relatively stable and the corrosion processes can be studied using EIS technique. In the case of pH 3.5 and during the entire corrosion process, the Nyquist plot was composed of a high‐frequency capacitive arc due to corrosion reaction and a low‐frequency capacitive arc due to the formation of corrosion products layer, and the corrosion rate during the same cycle was almost the same. In the case of pH 4.5 and during the first several cycles, the Nyquist plot was composed of nearly only one capacitive arc due to the corrosion reaction, and the corrosion rate during the same cycle increased with time. Additionally, the EIS features of the entire corrosion processes of 2024‐T3 aluminum alloy were interpreted theoretically.