Tailor-made gold brush nanoelectrode ensembles modified with l-cysteine for the detection of daunorubicine

A new functionalized l-cysteine surface modified 3D gold brush nanoelectrode assembly BNEE (l-cys/BNEEs) was prepared. The BNEEs consisted of gold nanowires 100 nm in diameter and up to 400 nm in length fabricated by template synthesis in track etched polycarbonate membranes. The nanowires were exposed by controlled chemical etching of the membrane and were then modified by coating l-cys on the surface of the exposed gold nanowires. The morphology of the BNEEs was imaged by scanning electron microscopy and the real active area of BNEEs was determined by electrochemical impedance spectroscopy. The redox of daunorubicine (DNR) at the l-cys/BNEEs exhibited absorption-controlled characteristics and higher current activity than that at l-cys surface modified 2D disk NEEs (l-cys/DNEEs). The square wave voltammetry technique was employed to detect DNR. The detection limit was 1.0 × 10⁻⁸ M (s/n = 3). The linear detection concentration range of DNR was from 2.5 × 10⁻⁸ to 4.0 × 10⁻⁷ M.     

Mathematical modelling of the solubility of supercritical CO2 in poly(l-lactide) and poly(d,l-lactide-co-glycolide)

Two mathematical models, Sanchez–Lacombe equation of state and the Perturbed-Chain Statistical Associating Fluid Theory were applied for modelling the phase equilibrium for the poly(l-lactide)–CO₂ and poly(d,l-lactide-co-glycolide)–CO₂ systems. Aspen Polymer Plus software was used. The results were compared with previously obtained experimental values for solubility. The solubility of scCO₂ in the two biodegradable polymers was calculated for three different temperatures (308, 313 and 323 K) in the pressure range (10–30 MPa). The characteristic parameters for the components and the binary interaction parameters for the models were optimized in order to obtain the best fit between the estimated and the experimental gas solubility data. The results suggest that both SL EOS and PC-SAFT are reliable models in describing the phase equilibrium of the PLLA–CO₂ and PLGA–CO₂ systems at the proposed working conditions.     

Synthesis and characterization of poly(l-glutamic acid)-block-poly(l-phenylalanine)

Poly(γ-benzyl l-glutamate)-block-poly(l-phenylalanine) was prepared via the ring opening polymerization of γ-benzyl l-glutamate N-carboxyanhydride and l-phenylalanine N-carboxyanhydride using n-butylamine·HCl as an initiator for the living polymerization. Polymerization was confirmed by ¹H-nuclear magnetic resonance spectroscopy and matrix assisted laser desorption ionization time of flight mass spectroscopy. After deprotection, the vesicular nanostructure of poly(l-glutamic acid)-block-poly(l-phenylalanine) particles was examined by transmission electron microscopy and dynamic light scattering. The pH-dependent properties of the nanoparticles were evaluated by means of ζ-potential and transmittance measurements. The results showed that the block copolypeptide could be prepared using simple techniques. Moreover, the easily prepared PGA-PPA block copolypeptide showed pH-dependent properties due to changes in the PGA ionization state as a function of pH; this characteristic could potentially be exploited for drug delivery applications.     

Electrocatalytic oxidation of l-cysteine with a stable copper-cobalt hexacyanoferrate electrochemically modified carbon paste electrode

A stable composition of hybrid copper-cobalt hexacyanoferrate (Cu-CoHCF) film was electrodeposited on a carbon paste electrode (CPE). There are a few reports for using this hybrid as a mediator, but all of them require almost 12 h conditioning time before usage. Contrary to previous reports this electrode does not require any conditioning and can be used immediately after film formation. The electrocatalytic activity of this film was investigated and showed a good electrocatalytic effect for oxidation of l-cysteine (Cys) in phosphate buffer solution (PBS) in pH range of 1-7. A linear range of 6 μM to 1 mM of Cys and an experimental detection limit of 5 μM of Cys were obtained using cyclic voltammetry method. The diffusion coefficient of Cys and catalytic rate constant for electrocatalytic reaction were also calculated. The major problem reported in electro oxidation of Cys is poisoning of electrode surface with reaction product, but in this study oxidation of Cys had no significant fouling effect on the modified electrode surface for the concentrations below 0.5 mM of Cys.     

Electrochemical detection of l-cysteine using a boron-doped carbon nanotube-modified electrode

A boron-doped carbon nanotube (BCNT)-modified glassy carbon (GC) electrode was constructed for the detection of l-cysteine (L-CySH). The electrochemical behavior of BCNTs in response to l-cysteine oxidation was investigated. The response current of L-CySH oxidation at the BCNT/GC electrode was obviously higher than that at the bare GC electrode or the CNT/GC electrode. This finding may be ascribed to the excellent electrochemical properties of the BCNT/GC electrode. Moreover, on the basis of this finding, a determination of L-CySH at the BCNT/GC electrode was carried out. The effects of pH, scan rate and interferents on the response of L-CySH oxidation were investigated. Under the optimum experimental conditions, the detection response for L-CySH on the BCNT/GC electrode was fast (within 7 s). It was found to be linear from 7.8 × 10⁻⁷ to 2 × 10⁻⁴ M (r = 0.998), with a high sensitivity of 25.3 ± 1.2 nA mM⁻¹ and a low detection limit of 0.26 ± 0.01 μM. The BCNT/GC electrode exhibited high stability and good resistance against interference by other oxidizable amino acids (tryptophan and tyrosine).     

Electrochemical reduction of Zn(II) ions on l-cysteine coated gold electrodes

Zn(II) ions have been selectively bound to the l-cysteine coated gold electrode in the form of a four-coordinated complex. Voltammograms of the Zn complex on the l-cysteine coated gold electrode showed a cathodic wave at ca. 0.05 V in the pH 7.54 phosphate buffered saline. The charge transfer coefficient and rate constant for the reduction of this Zn complex were 0.65 and 0.003 s⁻¹, respectively. The complexation of Zn(II) ions with l-cysteine on the gold electrode resulted in the maximum surface coverage of the Zn complex of 0.35 nmol cm⁻² and the Gibbs energy change of −27.6 kJ mol⁻¹. The cathodic peak current, influenced by the types of the end functional groups in thiols, the preconcentration time, and pH values of the supporting electrolyte, was linear with the concentration of Zn(II) ions in the range of 5.0 nM to 5 μM with a detection limit of 2.1 nM. The proposed voltammetric method was utilized successfully to detect the concentration of Zn(II) ions in hairs.     

Electrochemical behaviour of N-acetyl-l-cysteine on gold electrode—A tentative reaction mechanism

The electrochemical behaviour of N-acetyl-l-cysteine (NAC) has been investigated by linear and cyclic voltammetry on gold electrode at room temperature. The results showed two oxidation peaks under acid and neutral conditions and only one in basic medium. For each oxidation, as many electron was exchanged as proton. The influence of both the concentration and the potential scan rate on the peak currents highlighted a diffusion-controlled phenomenon for the first peak and an adsorption-limited reaction rate for the second one. The diffusion coefficient of NAC in solution and the surface concentration of the adsorbed species at pH 3 and 7 were close to 2 × 10⁻⁴ to 2 × 10⁻⁵ cm² s⁻¹ and 6 × 10⁻⁹ to 6 × 10⁻¹⁰ mol cm⁻², respectively. Film transfer experiments resulted in an irreversible adsorption of NAC on gold electrode, and the formation of a self-assembled monolayer (SAM).     

Thermal degradation of poly(l-lactide): effect of alkali earth metal oxides for selective l,l-lactide formation

To achieve the feed stock recycling of poly(l-lactide) (PLLA) to l,l-lactide, PLLA composites including alkali earth metal oxides, such as calcium oxide (CaO) and magnesium oxide (MgO), were prepared and the effect of such metal oxides on the thermal degradation was investigated from the viewpoint of selective l,l-lactide formation. Metal oxides both lowered the degradation temperature range of PLLA and completely suppressed the production of oligomers other than lactides. CaO markedly lowered the degradation temperature, but caused some racemization of lactide, especially in a temperature range lower than 250 °C. Interestingly, with MgO racemization was avoided even in the lower temperature range. It is considered that the effect of MgO on the racemization is due to the lower basicity of Mg compared to Ca. At temperatures lower than 270 °C, the pyrolysis of PLLA/MgO (5 wt%) composite occurred smoothly causing unzipping depolymerization, resulting in selective l,l-lactide production. A degradation mechanism was discussed based on the results of kinetic analysis. A practical approach for the selective production of l,l-lactide from PLLA is proposed by using the PLLA/MgO composite.     

Controlled crystal nucleation in the melt-crystallization of poly(l-lactide) and poly(l-lactide)/poly(d-lactide) stereocomplex

Among the various inorganic nucleators examined, Talc and an aluminum complex of a phosphoric ester combined with hydrotalcite (NA) were found to be effective for the melt-crystallization of poly(l-lactide) (PLLA) and PLLA/poly(d-lactide) (PDLA) stereo mixture, respectively. NA (1.0 phr (per one hundred resin)) can exclusively nucleate the stereocomplex crystals, while Talc cannot suppress the homo crystallization of PLLA and PDLA in the stereo mixture. Double use of Talc and NA (in 1.0 phr each) is highly effective for enhancing the crystallization temperature of the stereo complex without forming the homo crystals. The stereocomplex crystals nucleated by NA show a significantly lower melting temperature (207 °C) than the single crystal of the stereocomplex (230 °C) in spite of recording a large heat of crystallization ΔH_c (54 J/g). Photomicrographic study suggests that the spherulites with a symmetric morphology are formed in the stereo mixture added with NA while the spherulites do not grow in size in the mixture added with Talc. The exclusive growth of the stereocomplex crystals by the melt-crystallization process will open a processing window for the PLLA/PDLA.     

A homogeneous redox catalytic process for the paired synthesis of l-cysteine and l-cysteic acid from l-cystine

Redox catalytic process involved in the paired electrosynthesis of l-cysteine and l-cysteic acid from l-cystine is investigated by cyclic voltammetric technique and also confirmed by preparative electrolysis. The cyclic voltammetric behaviour shows that in the catholyte, in situ deposited tin (Sn) surface acts as a redox catalyst for the electro-reduction of l-cystine to l-cysteine whereas in the anolyte, the electro-generated bromine acts as a homogeneous redox mediator to enhance the electro-oxidation of l-cystine. l-Cysteine hydrochloride monohydrate (l-cysteine) and l-cysteic acid are prepared from l-cystine by preparative electrolysis with high purity and high yield using graphite cathode and DSA anode. At optimum concentration of l-cystine with 1:1 concentration ratio (catholyte:anolyte), the material yield obtained for l-cysteine is above 80% and that for l-cysteic acid is close to 60% in the paired electrosynthesis process in the batch operation. Scope for further experiments in conversion efficiency is also discussed.     

Spherulite growth of l-lactide copolymers: Effects of tacticity and comonomers

The spherulite growth behavior and mechanism of l-lactide copolymers, poly(l-lactide-co-d-lactide) [P(LLA-DLA)], poly(l-lactide-co-glycolide) [P(LLA-GA)], and poly(l-lactide-co-ε-caprolactone) [P(LLA-CL)] have been studied using polarization optical microscopy in comparison with poly(l-lactide) (PLLA) having different molecular weights to elucidate the effects of incorporated comonomer units. The incorporation of comonomer units reduced the radius growth rate of spherulites (G) and increased the induction period of spherulite formation (t_i), irrespective of the kind of comonomer unit. Such effects became remarkable with the content of comonomers. At a crystallization temperature (T_c) of 130 °C, the disturbance effects of comonomers on the spherulite growth decreased in the following order: d-lactide>glycolide>ε-caprolactone, when compared at the same comonomer unit or reciprocal of averaged l-lactyl unit sequence length (l_l). The t_i estimation indicated that the glycolide units have the lowest disturbance effects on the formation of spherulite (crystallite) nuclei. The PLLA having the number-average molecular weight (M_n) exceeding 3.1×10⁴ g mol⁻¹ showed the transition from regime II to regime III at T_c=120 °C, whereas PLLA with the lowest M_n of 9.2×10³ g mol⁻¹ crystallized solely in regime III kinetics and the copolymers excluding P(LLA-DLA) with 3% of d-lactide units crystallized solely according to regime II kinetics. The nucleation and front constant for regime II and III [K_g(II), K_g(III), G₀(II), and G₀(III), respectively] estimated with each (not with a fixed for high-molecular-weight PLLA) decreased with increasing the amount of defects per unit mass of the polymer for crystallization, i.e. with increasing the comonomer content and the density of terminal group through decreasing the molecular weight.     

The reduction of l-cystine hydrochloride at stationary and rotating disc mercury electrodes

The kinetics of l-cystine hydrochloride reduction have been studied at a mercury-plated copper rotating disc electrode (RDE) and at a stationary mercury disc electrode (SMDE) in 0.1 mol dm⁻³ HCl at 298 K. The reduction of the disulphide is irreversible and hydrogen evolution is the major side reaction. In contrast to steady state electrode kinetic studies at a mercury drop electrode (which shows a well-defined limiting current), the mercury-plated Cu RDE shows overlap between disulphide reduction and hydrogen evolution. These effects are attributable to strong reactant adsorption with a calculated surface coverage close to 100%. A Tafel slope of −185 mV per decade is found with a cathodic transfer coefficient of 0.32 and a formal rate constant of 6.7 × 10⁻⁹ m s⁻¹. The relative merits of steady state voltammetry at a mercury-plated copper RDE and linear sweep voltammetry at the SMDE are discussed, as is the mechanism of l-cysteine hydrochloride formation.     

Feasibility study of using montmorillonite for stability enhancement of l-ascorbic acid

This study tended to construct new l-ascorbic acid (LAA) composites in low toxicity and high stability for feasible application. LAA is chemically very unstable, since it is easily oxidized into biologically inactive compounds naturally. Our finding showed that introduction of montmorillonite (MMT) could significantly attenuate its toxicity and to sustain the stability of LAA with economic feasibility for practical uses. In addition, as phosphoric acid was biologically compatible, it was used for the pretreatment of MMT to obtain a promising stabilization of LAA. Toxicity assessment also showed that MMT treated with low-concentration acids should be considered as biologically safe according to our assessment. Thus, using acid treated MMT to stabilize LAA in a long-term might be technically feasible for further uses.     

Drowning-out crystallization of l-proline: Effect of anti-solvent composition and processing parameters on crystal size and shape

Crystallization of l-proline was investigated using a drowning-out method. Due to the high water and alcohol solubility of l-proline, the recovery of an l-proline product by precipitation using the drowning-out method required suitable anti-solvents selected from immiscibility and solubility studies. Through past experience, acetone and NMP were carefully chosen for analogy and solubility tests in pure anti-solvent. Although phase separation occurred in acetone, ultrasound was used to mix the two immiscible phases and generate fine emulsion droplets. l-proline crystals were obtained using NMP with a general drowning-out method. A spherical agglomerate of l-proline was also obtained using acetone by emulsion solvent diffusion methods. The ultrasound power controlled the agglomerate sizes, and the agglomerate surface transformed from amorphous to crystalline as the residence time increased. Alternatively, when NMP was used as an anti-solvent, l-proline monocrystals with needle type morphology were produced.     

Broadband dielectric spectroscopic characterization of the hydrolytic degradation of carboxylic acid-terminated poly(d,l-lactide) materials

Broadband dielectric spectroscopy was used to examine carboxylic acid-terminated poly(d,l-lactide) samples that were hydrolytically degraded in 7.4 pH phosphate buffer solutions at 37 °C. The dielectric spectral signatures of degraded samples were considerably more distinct than those of undegraded samples and a T_g-related relaxation associated with long range chain segmental mobility was seen. For both degraded and undegraded samples, a relaxation peak just beneath a DSC-based T_g was observed, which shifts to higher frequency with increasing temperature. Thus, this feature is assigned as the glass transition as viewed from the dielectric relaxation perspective. Linear segments on log-log plots of loss permittivity vs. frequency, in the low frequency regime, are attributed to d.c. conductivity. An upward shift in relaxation peak maximum, f_max, observed especially after 145 d of immersion in buffer, implies a decrease in the time scale of long range segmental motions with increased degradation time.Permittivity data for degraded and undegraded materials were fitted to the Havriliak-Negami equation with subtraction of the d.c. conductivity contribution to uncover pure relaxation peaks. Parameters extracted from these fits were used to construct Vogel-Fulcher-Tammann-Hesse (VFTH) curves and distribution of relaxation time, G(τ), curves for all samples. It was seen that the relaxation times for the α-transition in both degraded and undegraded samples showed VFTH temperature behavior. G(τ) curves showed a general broadening and shift to lower τ with degradation, which can be explained in terms of a broadening of molecular weight within degraded samples and faster chain motions.     

Functionalized micelles from new ABC polyglycidol-poly(ethylene oxide)-poly(d,l-lactide) terpolymers

New ABC type terpolymers of poly(ethoxyethyl glycidyl ether)/poly(ethylene oxide)/poly(d,l-lactide) were obtained by multi-mode anionic polymerization. After successive deprotection of the ethoxyethyl groups from the first block, highly hydroxyl functionalized copolymers of polyglycidol/poly(ethylene oxide)/poly(d,l-lactide) were obtained. These copolymers form elongated ellipsoidal micelles by direct dissolution in water. The micelles consist of a poly(d,l-lactide) core and stabilizing shell of polyglycidol/poly(ethylene oxide). The hydroxyl groups of polyglycidol blocks situated at the micelle surface provide high functionality, which could be engaged in further chemical modification resulting in a potential drug targeting agents. The micellization process of the copolymers in aqueous media was studied by hydrophobic dye solubilization, static and dynamic light scattering, and transmission electron microscopy.     

Three-dimensional electrochemical microfabrication of n-GaAs using l-cystine as a scavenger

The confined etchant layer technique (CELT) was used to fabricate complex three-dimensional (3D) microstructures on gallium arsenide (n-GaAs). The design of an appropriate chemical etching system is needed in order to realize successful microfabrication. In this study, Br₂ was electro-generated at the mold surface and used as an efficient etchant for n-GaAs. The use of l-cystine as a scavenger to replace the toxic scavenger H₃A_SO₃ was explored. The resolution of the fabricated microstructure depended strongly on the composition of the electrolyte, and especially on the concentration ratio between l-cystine and KBr. A well-defined and polished Pt micro-cylindrical electrode with a diameter of ∼50 μm was employed as one kind of mold for CELT. By inspecting the deviation of the sizes of the etching spots from the real diameter of the microelectrode, the thickness of confined etchant layer (CEL) can be estimated and thus the composition of electrolyte can be optimized for better etching precision. By choosing an appropriate concentration ratio between l-cystine and KBr, complex microstructures were fabricated successfully on n-GaAs. The etched patterns on n-GaAs were approximately negative copies of the mold, and the precision of duplication could easily reach the submicrometer scale, which was better than that achieved with H₃A_SO₃. The experimental results indicated that l-cystine is a good scavenger for microfabrication on n-GaAs by CELT. This technique avoids severe pollution of the environment, which will help to extend its future application in industry.     

Dielectric study on dynamics and conformation of poly(d,l-lactic acid) in dilute and semi-dilute solutions

Fractionated samples of d,l-poly(lactic acid) (PLA) were prepared and the dielectric normal mode relaxation was studied for dilute and semi-dilute solutions of the PLA in a good solvent benzene. Results indicate that in the dilute regime the normal mode relaxation time is proportional to [η]M_w in agreement with the Rouse-Zimm theory, where [η] and M_w denote the intrinsic viscosity and weight average molecular weight, respectively. The dielectric relaxation strength which is proportional to the mean square end-to-end distance 〈r²〉 increases with increasing M_w with the power of 2ν, where ν is the excluded volume parameter determined from [η]. The relaxation time in the semi-dilute regime increases with increasing concentration C due to increases of the entanglement density and the friction coefficient. The relaxation time corrected to the iso-friction state agrees approximately with the dynamic scaling theories. The relaxation strength decreases with increasing concentration indicating that 〈r²〉 decreases on account of the screening of the excluded volume effect. The concentration dependence of 〈r²〉 agrees approximately with the scaling theory proposed by Daoud and Jannink.     

Transcrystalline structures of poly(l-lactide)

Poly(l-lactide) (PLLA) film containing transcrystalline (TC) structures can easily be obtained by placing PLLA films melted between two poly(tetrafluoroethylene) (PTFE) sheets, followed by isothermal crystallization at 122 °C. The fine structures of the PLLA-TC film were studied by various structural techniques such as X-ray diffractometry, optical microscopy and transmission electron microscopy. We also examined the purification effect upon the morphology of PLLA-TC film. The formation of the TC structures revealed that one-dimensional spherulitic growth occurred from the assembling impurities as nucleation agent near the PTFE substrate in the heterogeneous nucleation system. We found that the b-axis of PLLA crystal was parallel to the lamellae growth direction confirmed using X-ray diffraction. The precipitated PLLA film crystallized in a similar process exhibited scanty TC textures, suggesting that the existence of impurity in the PLLA sample was an important factor for the formation of those structures.     

Enhanced production of l(+)-lactic acid by floc-form culture of Rhizopus oryzae

A process to optimize l-lactic acid production from glucose by Rhizopus oryzae, based on sustaining floc morphology throughout the fermentation process, is herein performed. During the fermentation, supplementary ammonium sulfate was added intermittently to maintain the ammonia level of the culture medium always higher than 0.1 g/L. With replenish of nitrogen source, mycelia flocs did not aggregate, and the lactic acid production was optimized upon the fermentation being controlled at pH 4.3–4.5 by adding calcium carbonate slurry. In contrast, without supplementary addition of nitrogen source, mycelial clumps formed, resulting in a poor production of lactic acid. In the initial batch fermentation process, the final concentration of lactic acid produced was 109 g/L, with a yield (g lactic acid/g glucose consumed) of 0.87 and a productivity of 2.73 g/L h, using 125 g/L of glucose as substrate. For the first four cycles of repeated-batch fermentation, the average final concentration, the productivity and the yield of lactic acid were 113 g/L, 4.03 g/L h and 0.90, respectively.