The ability of precision hard turning to increase rolling contact fatigue life

In this paper, precision hard turning is proposed for the finishing of the AISI 52100 bearing components to improve rolling contact fatigue life. This finishing process induces a homogenous microstructure at surface and subsurface layers. Fatigue life tests performed on a twin-disk machine show that rolling contact fatigue life increases as R_a value decreases. The bearing components reached 0.32 million cycles for R_a=0.25 μm and 5.2 million cycles for R_a=0.11 μm. In comparison, the bearing components achieved 1.2 million cycles with grinding (R_a=0.2 μm) and 3.2 million cycles with grinding followed by honing (R_a=0.05 μm) respectively.     

Parameters optimization on surface roughness improvement of Zerodur optical glass using an innovative rotary abrasive fluid multi-jet polishing process

With the advance of contemporary technology, high precision surface finishing techniques for optical glasses are of great concern and developing to meet the requirements of the effective industrialized processes. Not only the used tools but also process parameters have great influence on the surface roughness improvements. In this paper, surface roughness improvement of Zerodur optical glass using an innovative rotary abrasive fluid multi-jet polishing process has been presented. For the same purpose, a tool for executing ultra precision polishing was designed and manufactured. Taguchi's experimental approach, an L₁₈ orthogonal array was employed to obtain the optimal process parameters. ANOVA analysis has also been carried out to determine the significant factors. It was observed that about a 98.33% improvement on surface roughness from (R_a) 0.360 μm to (R_a) 0.006 μm has been achieved. The experimental results show that a surface finished achieved can satisfy the requirements for optical-quality surface (R_a < 12 nm). In addition, the influence of significant factors on surface roughness improvement has been discussed in this study.     

Erosive smoothing of abrasive slurry-jet micro-machined channels in glass,PMMA, and sintered ceramics: Experiments and roughness model

Abrasive slurry jet micro-machining (ASJM) was used to machine channels in glass, PMMA, zirconium tin titanate, and aluminum nitride. The channel roughness was measured as a function of the ASJM process parameters particle size, dose, impact velocity, and impact angle. The steady-state roughness of the channels was reached relatively quickly for typical ASJM abrasive flow rates. The roughness of channels having depth-to-width aspect ratios up to about 0.25 could be reduced by approximately 35% compared to the roughest channel by decreasing particle impact velocity and angle. However, machining at such conditions reduced the specific erosion rate by 64% on average. It was therefore quicker to post-blast reference channels (225 nm average root mean square (R_rms) roughness) using process parameters selected for peak removal. It was also found that the roughness of reference channels could be reduced by about 78% by post-blasting using 3 μm diameter silicon carbide particles at 15° jet incidence. The smoothest post-blasted channels had an R_rms roughness of about 23 nm in glass, PMMA, and zirconium tin titanate, and 170 nm in aluminum nitride. Computational fluid dynamics was used to predict the particle impact conditions that were used in a model to predict the steady-state roughness due to ductile erosion with an average error of 12%.     

Simulation of surface generated during abrasive flow finishing of Al/SiCp-MMC using neural networks

Abrasive flow machining (AFM) is a multivariable finishing process which finds its use in difficult to finish surfaces on difficult to finish materials. Near accurate prediction of generated surface by this process could be very useful for the practicing engineers. Conventionally, regression models are used for such prediction. This paper presents the use of artificial neural networks (ANN) for modeling and simulation of response characteristics during AFM process in finishing of Al/SiC_p metal matrix composites (MMCs) components. A generalized back-propagation neural network with five inputs, four outputs, and one hidden layer is designed. Based upon the experimental data of the effects of AFM process parameters, e.g., abrasive mesh size, number of finishing cycles, extrusion pressure, percentage of abrasive concentration, and media viscosity grade, on performance characteristics, e.g., arithmetic mean value of surface roughness (R _a, micrometers), maximum peak–valley surface roughness height (R _t, micrometers), improvement in R _a (i.e., ΔR _a), and improvement in R _t (i.e., ΔR _t), the networks are trained for finishing of Al/SiC_p-MMC cylindrical components. ANN models are compared with multivariable regression analysis models, and their prediction accuracy is experimentally validated.     

Influence of surface preparation on roughness parameters,friction and wear

The aim of the present research was to investigate influence of surface preparation on roughness parameters and correlation between roughness parameters and friction and wear. First the correlation between different surface preparation techniques and roughness parameters was investigated. For this purpose 100Cr6 steel plate samples were prepared in terms of different average surface roughness, using different grades of grinding, polishing, turning and milling. Different surface preparation techniques resulted in different R_a values from 0.02 to 7 μm. After this, correlation between surface roughness parameters and friction and wear was investigated. For this reason dry and lubricated pin-on-disc tests, using different contact conditions, were carried out, where Al₂O₃ ball was used as counter-body. It was observed that parameters R_ku, R_sk, R_pk and R_vk tend to have influence on coefficient of friction.     

Measurement of various properties of Southern pine and aspen as function of heat treatment

The objective of this study was to investigate the influence of heat treatment parameters, namely temperature and exposure time on surface roughness, shear strength, hardness and density of Southern pine (Pinus echinata) and aspen (Populus grandidentata) samples. The specimens were exposed to two different temperature levels of 120–200 °C for time spans of 2–8 h. A stylus type portable profilometer was employed to evaluate the surface characteristics of the samples by taking measurements across the grain orientation. Average roughness (R_a), mean peak-to-valley height (R_z) and maximum roughness (R_max) were used to evaluate surface roughness of the samples exposed to various heat treatment schedules. Comten testing unit was also used to determine shear strength and Janka hardness of the control and heat treated specimens. Based on the results of this study Southern pine samples had more enhanced surface quality but lower hardness values than those of aspen specimens with increased temperature and time of heat treatment schedules. It was found that heat treatment adversely affected hardness and shear strength properties of all types of samples. Reduction in shear strength values of Southern pine and aspen samples ranged from 23.31% to 68.59% and from 4.67% to 48.55%, respectively as compared to those of control samples. It appears that influence of heat treatment on all properties of the samples was more pronounced with increasing temperature and exposure time.     

Copper alloys disintegration using pulsating water jet

This paper deals with on the investigation of surface topography, morphology and anisotropy of copper alloys – brass and bronze, created by pulsating water jet with frequency 20.38 kHz. The material was disintegrated using more passes of a pulsating water jet using flat nozzle, at pressure 40 MPa and stand off distance z = 55 mm. The average values of Ra, Rq, Rz roughness were analyzed at changing traverse speed and number of transitions. The effect of tensile strength and material hardness as mechanical properties of material affecting the average value of the roughness has been evaluated. It is assumed that this new way of metal eroding can be used in the automotive and engineering industries in the future e.g. for surface treatment.     

Nanofinishing of freeform surfaces (knee joint implant) by rotational-magnetorheological abrasive flow finishing (R-MRAFF) process

Freeform complex surfaces have become an inevitable part of many devices to perform specific functions. Some of these components require nanolevel surface roughness value to meet the desired requirements in their applications. Finishing of freeform surfaces to nanometer surface roughness value is always difficult for any process. Rotational-magnetorheological abrasive flow finishing (R-MRAFF) process has been applied so far for finishing internal surfaces of relatively simple geometry. In this work, an attempt has been made to improve external topography of freeform surfaces using this process. Large hydrodynamic pressure coupled with magnetic fluid is the principal idea behind these experiments. A smooth mirror like finished surface is achieved with improved finishing rate (nanometer/min) by controlling two motions (axial and rotational) simultaneously on stainless steel workpiece similar to knee joint implant. Magnetorheological polishing fluid with different mesh sizes of abrasive particles and at different extrusion pressures is used to reduce final surface roughness value, to increase uniformity of surface finish on the freeform surface and to enhance finishing rate. Surface roughness ranging from 35 to 78 nm is achieved at various locations as compared to larger variation in Ra value obtained in the earlier research work.     

Evolution of wear,roughness, and friction of Alloy 600 superalloy surfaces in water-submersed sliding

Self-mated wear and friction of Alloy 600 superalloy was studied in a water-submersed ring-on-rod configuration, loading the side of a 6.35 mm diameter rod across the flat surface of a rotating annular ring of 100 mm outer diameter and 70 mm inner diameter producing two sliding contacts along the ring. Tests were conducted at sliding speeds of 0.178 and 0.330 m/s for sliding distances of 100 m. Normal loads of 51 and 204 N were applied, and initial R_a surface roughnesses of the rings along the sliding direction were either smooth (～0.2 μm) or rough (～7.5 μm). Increased initial ring roughness caused a ～20-fold increase in rod wear at the lighter load, whereas at the heavier load increased initial roughness only caused a ～4-fold increase in wear. At lower initial ring roughness the 4-fold decrease in normal load caused a large (one order-of-magnitude) decrease in rod wear, whereas for rings of higher initial roughness the 4-fold decrease in normal load caused only minor (2-fold or less) decreases in rod wear. Wear during this 100 m sliding distance only experienced a minor effect from the 1.8-fold change in sliding speed, as did friction. In all cases friction coefficient rapidly settled into the range 0.6–0.7, except in the cases of lower load on rings of lower initial roughness where friction coefficient remained above 1 for most of this sliding duration. At this lower load the initial ～0.2 μm rod roughnesses increased to nearly 0.8 μm by the 100 m sliding distance, whereas at the higher load this same sliding distance resulted in roughnesses returning near to the initial 0.2 μm. It was hypothesized more highly loaded cases also went through initial roughening prior to smoothening back to 0.2 μm roughness within the 100 m sliding distance, and given additional sliding the more lightly loaded cases would also experience subsequent smoothening. Increasing sliding distance to 400 m, roughnesses indicated a smoothening back to 0.2 μm level during those lightly loaded tests, with friction coefficient correspondingly dropping from 1 into the 0.6–0.7 range observed in all other cases. Extended sliding to 400 m at light loading against rings of lower initial roughness also allowed a rod wear rate which increased with increased sliding distance to be observed, approaching the same rate observed against initially rough rings within the 100 m sliding distance.     

Specific energy and surface roughness of minimum quantity lubrication grinding Ni-based alloy with mixed vegetable oil-based nanofluids

Vegetable oil is a low toxic, excellent biodegradable and renewable energy source used as an ideal lubricating base oil in machining. Castor oil exhibits good lubrication performance but poor mobility, which limits its application especially in precision grinding. The main objective of the work presented to obtain optimal mixed vegetable based-oil and optimal nanoparticles adding concentration in grinding Ni-based alloy with minimum quantity lubrication. An experimental investigation is carried out first to study the different vegetable oils with excellent mobility mixed with castor oil. The lubrication property of the oil was evaluated in terms of grinding force, force ratio, specific grinding energy, and surface roughness. Based on the test conditions, it is found that soybean/castor mixed oil obtained the optimal results (μ= 0.379, U = 83.27 J/mm³ and Ra = 0.325 μm) and lubricating effect compared with castor oil and other mixed base oils. To further explore the lubricating capability of soybean/castor mixed oil, MoS₂ nanoparticles which have excellent lubricating property were added into the soybean/castor mixed oil to prepare different concentrations nanofluids. From the present study, it can be concluded that 8% mass fraction of the oil mixture should be added to obtain the optimal machining results, with the lowest force ratio (0.329), specific energy (58.60 J/mm³), and average grinding temperature (182.6 °C). Meanwhile, better surface microtopography of ground parts and grinding debris morphologies were also observed for the machining conditions.     

Ultrasonic vibration assisted grinding of hard and brittle linear micro-structured surfaces

In this paper, a novel ultrasonic vibration assisted grinding (UVAG) technique was presented for machining hard and brittle linear micro-structured surfaces. The kinematics of the UVAG for micro-structures was first analyzed by considering both the vibration trace and the topological features on the machined surface. Then, the influences of the ultrasonic vibration parameters and the tilt angle on the ground quality of micro-structured surfaces were investigated. The experimental results indicate that the introduction of ultrasonic vibration is able to improve the surface quality (The roughness SR_a was reduced to 78 nm from 136 nm), especially in guaranteeing the edge sharpness of micro-structures. By increasing the tilt angle, the surface roughness can be further reduced to 56 nm for a 59% improvement in total. By using the preferred UVAG parameters realized by orthogonal experiments, a micro cylinder array with surface roughness of less than 50 nm and edge radius of less than 1 μm was fabricated. The primary and secondary sequence of the grinding parameters obtained by the orthogonal experiments are as follows: feed rate, tilt angle of workpiece, depth of grinding, vibration frequency and amplitude. The spindle speed in the range of 1000 rpm–3000 rpm does not significantly affect the machined micro-structured surface roughness. Finally, more micro-structures including a micro V-groove array and a micro pyramid array were machined on binderless WC as well as SiC ceramic by means of the UVAG technique. The edge radius on the V-grooves and pyramids are both less than 1 μm, indicating the feasibility of UVAG in machining hard and brittle micro-structured surfaces for an improved surface quality.     

Micro electrical discharge machining using high electric resistance electrodes

In micro electrical discharge machining (EDM), because the material removal per single pulse discharge mainly determines the minimum machinable size of a micro EDM, decreasing the material removal per single pulse discharge is important. In this study, in order to decrease the material removal per single pulse discharge, high electric resistance materials such as single-crystal silicon are used for electrodes. Analytical results show that when the electrode resistance increases, the peak value of the discharge current decreases, whereas the pulse duration increases. In addition, the discharge energy decreases when increasing the resistance. Silicon is used as a tool electrode, and the effect of resistivity of the silicon tool electrode on the diameter of discharge craters generated on the stainless steel workpiece is examined. Experimental results reveal that with increasing silicon electrode resistivity, the diameter of discharge craters decreases. Because the diameter of discharge craters can be decreased to 0.5 μm, improved finished surfaces of R_z 0.03 μm are obtained.     

Analysis of load-speed sensitivity of friction composites based on various synthetic graphites

The frictional response of a multi-component phenolic-based friction material is highly complex under a set of variable loads and speeds. The present paper discusses the sensitivity of friction coefficient (μ) of friction composites containing synthetic graphite with different particle sizes (with similar crystallinity range) to braking pressure and sliding speed. The friction studies were carried out on a sub scale brake-test-rig, following 4 loads × 3 speeds experimental design. The best combination of performance properties was observed for the composite containing synthetic graphite with an average particle size of 410 μm. Other particle sizes which resulted in good performance were 38 and 169 μm. Very fine particle sizes were not beneficial for desired combination of performance properties. Regression analysis of μ following an orthogonal L₉(3 × 3) experimental design method revealed that the first order influences of sliding speed and braking pressure were significant. When all the combinatorial influences of braking pressure and sliding speed are taken into account together their simultaneous effects would be most effective in the range of graphite particle size ～80–250 μm.     

On the film thickness dependence of shear strengths in sliding,boundary-layer friction

The density functional theory calculated pressure-dependent shear strength S of a four-layer slab of KCl on a Fe(1 0 0) substrate is compared to previous calculations for a bilayer slab to gauge the effect of film thickness on the shear properties of the film. It is found that the shear strength varies with pressure as S = S₀ + αP, where P is the contact pressure. The resulting calculated values for the four-layer slab are S₀〈1 0〉 = 62 ± 15 and S₀〈1 1〉 = 65 ± 11 MPa while α〈1 0〉 and α〈1 1〉 are 0.06 ± 0.01. The values are very close to those calculated for the bilayer slab of S₀〈1 0〉 = 64 ± 9 and S₀〈1 1〉 =69 ± 8 MPa and α〈1 0〉 and α〈1 1〉 of 0.05 ± 0.01, and in reasonable agreement with the experiment values. These results suggest that the thickness of the film does not have a profound effect on the shear properties.     

Effect of three nitriding treatments on tribological performance of 42CrAlMo7 steel in boundary lubrication

Evolution of friction and wear of 42CrAlMo7 steels with different nitriding processes was investigated during boundary-lubricated rolling–sliding tests. The wear behaviour of nitrided steel with a thin compound layer (produced by plasma nitriding and by gas nitriding followed by oxidation) was characterised by the early removal of the compound layer, and the wear resistance was thus, given by the underlying diffusion layer. In the case of the material with a thick compound layer (produced by gas nitriding) wear was restricted to the compound layer. In this material, at low applied load (300 N, i.e. 485 MPa of Hertzian pressure, in this work), after the removal of the external porous layer wear tended to be negligible. At high applied load (1000 N, 890 MPa), on the other hand, the wear rate became higher than that of the diffusion layer. The friction behaviour was followed by determining the λ-factor evolution during each test. For a given λ-factor, the friction coefficients at 300 N were lower than at 1000 N.     

Effect of carbide volume fraction on erosive wear behaviour of hardfacing cast irons

The present work reports the effect of carbide volume fraction on erosive wear behaviour of hardfacing cast irons. Five different grades of weld hardfacing cast irons were selected for the present investigation. The solid particle erosion experiments were carried out with blast furnace sinter, silica sand and alumina particles under mild (53–75 μm, 25 m s⁻¹), moderately severe (125–150 μm/100–150 μm, 50 m s⁻¹) and under severe erosion conditions (300–425 μm, 90 m s⁻¹) at impingement angles of 30 and 90°. The variation in erosion rate with carbide volume fraction was observed to be strong function of the erodent particle hardness, impingement angle and the impact velocity. Under mild erosion conditions, erosion rate decreased with increasing carbide volume fraction (CVF), whereas erosion rate increased with CVF under moderately severe erosion condition with alumina particles. With silica sand particles under moderately severe erosion conditions the beneficial effect of large volume fraction of carbides could only be observed at 30°, whereas at normal impact erosion rate increased with increasing CVF. The erosion rate showed power law relationship with ratio of hardness of erodent particle to that of the target material (H_e/H_t) and expressed as E=c(H_e/H_t)^p.With increasing severity of erosion conditions erosion rate showed stronger dependence on H_e/H_t as compared to those under mild and moderately severe erosion conditions. The mechanism of materials removal from the carbides involved Hertzian fracture with softer sinter particles, whereas harder alumina particles could plastically indent and cause gross fracture of the carbides.     

Cutting forces,tool wear and surface finish in high speed diamond machining

We have investigated the cutting forces, the tool wear and the surface finish obtained in high speed diamond turning and milling of OFHC copper, brass CuZn39Pb3, aluminum AlMg5, and electroless nickel. In face turning experiments with constant material removal rate the cutting forces were recorded as a function of cutting speed between v_c = 150 m/min and 4500 m/min revealing a transition to adiabatic shearing which is supported by FEM simulations of the cutting process. Fly-cutting experiments carried out at low (v_c = 380 m/min) and at high cutting speed (v_c = 3800 m/min) showed that the rate of abrasive wear of the cutting edge is significantly higher at ordinary cutting speed than at high cutting speed in contrast to the experience made in conventional machining. Furthermore, it was found that the rate of chemically induced tool wear in diamond milling of steel is decreasing with decreasing tool engagement time per revolution. High speed diamond machining may also yield an improved surface roughness which was confirmed by comparing the step heights at grain boundaries obtained in diamond milling of OFHC copper and brass CuZn39Pb3 at low (v_c = 100 m/min) and high cutting speed (v_c = 2000 m/min). Thus, high speed diamond machining offers several advantages, let alone a major reduction of machining time.     

The lubrication of poly(etheretherketone) by an aqueous solution of nattokinase

Poly(etheretherketone) (PEEK) is a high strength and high temperature engineering polymer. However, its tribological performance is not very good in its pure form unless fillers or fibers are added to form composites. As polymers are often used for applications where traditional oil based lubrication may become an issue, water-based lubrication is desirable. This paper explores the lubrication performance of a natural fibrinolytic enzyme, nattokinase, found in fermented soybean (natto) in the aqueous solution. Pins of PEEK were slid against a steel disk in a pin-on-disk tester with the aqueous lubrication. The counterface disk material was a tool steel (R_a=0.37 μm). Tests were conducted at a rotational speed of 100 rpm and a normal load of 80 N. For comparison, tests were also conducted in NaCl solution. Nattokinase aqueous solution provides a coefficient of friction of 0.2 between PEEK and steel as compared to 0.3–0.35 for dry condition. The specific wear rates of PEEK for dry, deionized water, NaCl solution and aqueous nattokinase solution conditions were 10.5×10^?6, 51.6×10^?6, 228×10^?6 and 8.8×10^?6 mm³/N m, respectively. The fibrinolytic nattokinase enzyme provides lubricity with alkalinity reducing corrosion and eventually reducing wear.     

Proficiency test for effective area determination of a pneumatic pressure balance in Mexico

A pneumatic pressure proficiency test for effective area determination of a pressure balance was performed among 4 accredited calibration laboratories in Mexico. CENAM provided the reference values (making initial and final calibrations) and was the pilot laboratory. The Mexican Accreditation Entity (ema) collaborated. The participants calibrated, by cross floating, a Wika pressure balance model CPB 5000 with accuracy class 0.015% of the reading in the range 0.7–7 MPa. The calibration pressures were 0.7, 1.4, 2.1 3.5, 4.2, 5.6 and 7.0 MPa. For A₀ and A_e, the normalized error equation was used to compare the results of the laboratories with CENAM’s reference values. The results obtained were satisfactory (E_n did not exceed the compatibility limit, −1 ⩽ E_n ⩽ 1).