A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al₂O₃ with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42 m s⁻¹ and a load of 196 N were used in all experiments. The average diameter 250 μm PEEK powders, the 15 or 90 nm Al₂O₃ nano-particles or 500 nm Al₂O₃ particles and/or the PTFE fine powders of diameter 50 μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al₂O₃ nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al₂O₃ reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al₂O₃/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15 nm Al₂O₃ particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al₂O₃ as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al₂O₃ to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.     

Studies on wear behavior of nano-intermetallic reinforced Al-base amorphous/nanocrystalline matrix in situ composite

Resistance to wear is an important factor in design and selection of structural components in relative motion against a mating surface. The present work deals with studies on fretting wear behavior of in situ nano-Al₃Ti reinforced Al–Ti–Si amorphous/nanocrystalline matrix composite, processed by high pressure (8 GPa) sintering at room temperature, 350, 400 or 450 °C. The wear experiments were carried out in gross slip fretting regime to investigate the performance of this composite against Al₂O₃ at ambient temperature (22–25 °C) and humidity (50–55%). The highest resistance to fretting wear has been observed in the composites sintered at 400 °C. The fretting wear involves oxidation of Al₃Ti particles in the composite. A continuous, smooth and protective tribolayer is formed on the worn surface of the composite sintered at 400 °C, while fragmentation and spallation leads to a rougher surface and greater wear in the composite sintered at 450 °C.     

Tribological behavior of PEEK components with compositionally graded PEEK/PTFE surfaces

PEEK is a high strength engineering thermoplastic that suffers from a high friction coefficient and a friction induced wear mode. Past studies with 10 μm PEEK and PTFE powders resulted in composite solid lubricant that (at the optimal composition) had a wear rate of k = 2 × 10⁻⁹ mm³/Nm with a friction coefficient of μ = 0.12. A compositional grading of PEEK and PTFE is implemented in this study to create a bulk composite with the functional requirements of component strength, stiffness and wear resistance while providing solid lubrication at the sliding interface. The tribological performances of three functionally graded PEEK components were evaluated on linear reciprocating, rotating pin-on-disk and thrust washer tribometers. Wear rates comparable to samples of the bulk solid lubricant and comparable or improved frictional performance were achieved by compositionally grading the near surface region of PEEK components.     

Tribological properties of NiCr–Al2O3 cermet-based composites with addition of multiple-lubricants at elevated temperatures

The tribological properties of NiCr-40 wt% Al₂O₃ (NC40A) cermet-based composites containing SrSO₄ and other lubricant (graphite, MoS₂ and Ag) against alumina ball were evaluated to identify their self-lubrication mechanisms from room temperature to 800 °C. The composites demonstrated distinct improvements in effectively reducing friction and wear, as compared to NC40A cermet. The best results were observed for NC40A–10SrSO₄–10Ag composite, which exhibited satisfactory reproducibility of friction coefficient over a wide temperature range (200–800 °C) through high temperature cyclic friction tests due to the formation of synergistic lubricating films SrAl₄O₇, NiCr₂O₄ and Ag on the contact surface.     

Corrosion wear behaviors of micro-arc oxidation coating of Al2O3 on 2024Al in different aqueous environments at fretting contact

The fretting wear behavior of micro-arc oxidation (MAO) coating of Al₂O₃ on an aluminum alloy 2024Al flat against a 440C stainless steel ball was investigated in artificial rainwater, artificial seawater and distilled water by using a ball-on-flat configuration with 300 μm amplitude at room temperature for 1 h. The morphology of the wear scars were observed and analyzed using scanning electron microscopy; the 3D-morphology and wear volume-loss were determined using a non-contact optical profilometer. Potentiodynamic anodic polarization was used to measure the corrosion behavior of the MAO coating before and after the corrosion wear test. The influences of the load, frequency and aqueous medium on the friction coefficient and wear volume-loss of the coatings were also analyzed. Results show that the friction coefficient decreases generally with an increase of the frequency in the three aqueous solutions; whereas it presents different variation trends as the load increased. In addition, aqueous environment does significantly influence the friction coefficient, the friction coefficient was the largest when fretting occurred in distilled water, smaller when fretting occurred in rainwater, and the smallest when fretting occurred in seawater. Particularly the remarkable antifriction effect of the seawater is of note. The wear-loss of the MAO coating in the distilled water is the largest at low frequency; however, it increases rapidly in rainwater and seawater at high frequency due to the corrosion effect of Cl^? ion as well as its accelerating effect to the wear process, and results in larger wear-loss than that in distilled water, which implies a positive synergism between corrosion and wear.     

Dry sliding wear behaviour of Al(Mg)/Al2O3 interpenetrating composites produced by a pressureless infiltration technique

Aluminium alloys, reinforced with ceramic particles or fibres, are desired materials in high performance applications due to their superior properties. In this paper, gel-cast Al₂O₃ foams were pressurelessly infiltrated using an Al–8 wt.% Mg alloy. The wear rates of the alloy and the Al(Mg)/Al₂O₃ interpenetrating composites were tested under dry sliding conditions; effects of Al₂O₃ foam density and cell size on the composite wear resistance under different loads and sliding distances were investigated. A ‘ploughing’ mechanism was observed in all the composites after an initial 250 m sliding distance, whilst the composites with the higher foam density show a ‘two-stage’ wear with sliding distance. The decrease in the wear rate in the second stage in the latter is attributed to an Al₂O₃ network protruding out of the worn surface, which protects the direct wear of the Al(Mg) alloy by the counter ball. Within the range studied, a larger cell size is preferred for better wear resistance.     

Mechanical and tribological behavior of nanostructured copper–alumina cermets obtained by Pulsed Electric Current Sintering

Nanostructured Cu–Al₂O₃ powders obtained by the reduction of CuO with Al in a high energy ball mill were successfully consolidated by Pulsed Electric Current Sintering (PECS). The effect of the composition and microstructure of these PECS Cu–Al₂O₃ cermets on their strength was investigated. The friction and wear behavior of these cermets were studied under reciprocating sliding against corundum at 23 °C and 50% RH, and compared to the behavior of coarse grained PECS sintered pure copper. The effect of grain size on the coefficient of friction was masked by the formation of a surface tribolayer. The wear depth recorded on Cu–Al₂O₃ is lesser than half the one on coarse grained copper. Surface and subsurface deformation studied through FIB cross-sections showed that delamination and oxidative wear were active on Cu and Cu–Al₂O₃ cermets respectively under the current sliding test conditions. PECS Cu–Al₂O₃ cermets showed a good thermal stability even at 600 °C.     

Tribological characterisation of siliconcarbonitride ceramics derived from preceramic polymers

Amorphous SiCN ceramics were prepared in a laboratory scale as disk shaped specimens with 10 mm diameter and 0.3 mm thickness. The friction and wear behaviour was characterised in gross slip fretting tests under unlubricated conditions at room temperature against steel (100Cr6) and ceramic (Al₂O₃). Tests with a ball-on-disk contact were performed in laboratory air with different content of water vapour. The results show clearly that the relative humidity has a significant effect on friction and wear behaviour. All tests in dry air lead to higher friction and higher wear rate than in normal air. Improved friction and wear behaviour was observed with increasing pyrolysis temperature up to 1100 °C of the SiCN specimens. This is attributed to increasingly better mechanical properties and higher stiffness of the amorphous network due to the evaporation of gaseous organic species and the formation of free graphite like carbon.     

WC–ZrO2 composites: processing and unlubricated tribological properties

In the present work, we report the processing and properties of WC–6 wt.% ZrO₂ composites, densified using the pressureless sintering route. The densification of the WC–ZrO₂ composites was carried out in the temperature range of 1500–1700 °C with varying time (1–3 h) in vacuum. The experimental results indicate that significantly high hardness of 22–23 GPa and moderate fracture toughness of ∼5 MPa m^1/2 can be obtained with 2 mol% Y-stabilized ZrO₂ sinter-additive, sintered at 1600 °C for 3 h. Furthermore, the friction and wear behavior of optimized WC–ZrO₂ composite is investigated on a fretting mode I wear tester. The tribological results reveal that a moderate coefficient of friction in the range from 0.15 to 0.5 can be achieved with the optimised composite. An important observation is that a transition in friction and wear with load is noted. The dominant mechanisms of material removal appear to be tribochemical wear and spalling of tribolayer.     

Abrasive wear in ceramic laminated composites

Laminated ceramic structures in the system Al₂O₃/Al₂O₃ + 3Y-TZP (A/AZ) were prepared using a tape casting technique in order to obtain ceramic layers with different compositions and thicknesses. Piezo-spectroscopy was used to evaluate the residual stresses arisen from a calibrated mismatch in thermal expansion coefficients of the layers during the sintering process of the composite. The dependence of the residual stresses in the A and AZ layers on their thickness ratio was established. A microscale ball cratering method was used to investigate the influence that the surface compressive stress can play on the abrasive wear resistance of the composite structures. The results were compared with those obtained with an unstressed reference material prepared either by lamination of pure alumina green-sheets or by cold isostatic pressing of alumina powder. The experimental results have shown that the abrasive wear resistance is higher for samples with compressive residual stresses within the surface regions.     

Mechanical and tribological properties of NiCr–Al2O3 composites at elevated temperatures

The effect of Al₂O₃ content on the mechanical and tribological properties of Ni–Cr alloy was investigated from room temperature to 1000 °C. The results indicated that NiCr–40 wt% Al₂O₃ composite exhibited good wear resistance and its compressive strength remained 540 MPa even at 1000 °C. The values obtained for flexural strength and fracture toughness at room temperature were 771 MPa, 15.2 MPa m^1/2, respectively. Between 800 °C and 1000 °C, the adhesive and plastic oxide layer on the worn surface of the composite was claimed to be responsible for low friction coefficient and wear rate.     

Tribological behaviors of hierarchical porous PEEK composites with mesoporous titanium oxide whisker

Hierarchical porous PEEK self-lubricating composites were prepared by mold-leaching and vacuum melting process under high temperature. The tribological behaviors were investigated for the porous PEEK composite and the porous composite after incorporating micro-porogen (NaCl) and mesoporous titanium oxide whiskers. If only micro-porogen was incorporated, the lowest steady state specific wear rate was observed for PEEK composites filled with 30% NaCl. Based on this porous PEEK composite, the effects of mesoporous titanium oxide whiskers and non-perforated titanium oxide whiskers on the friction and wear properties of PEEK composites were studied. Results showed that nano-micro porous PEEK composites with 30 wt% micro-porogen and 5 wt% mesoporous titanium oxide whiskers reached the lowest friction coefficient and specific wear rate, which were recorded as 0.0194 and 2.135×10^–16 m³/Nm under the load of 200 N. Compared with 15 wt% carbon fiber-reinforced PEEK composite which is widely used in industry, the wear resistance of the designed hierarchical porous PEEK composite increased by 41 times, showing outstanding wear resistance.     

Improved wear resistance in alumina-PTFE nanocomposites with irregular shaped nanoparticles

Past studies with PTFE nanocomposites showed up to 600× improvements in wear resistance over unfilled PTFE with the addition of Al₂O₃ nanoparticles. Irregular shaped nanoparticles are used in this study to increase the mechanical entanglement of PTFE fibrils with the filler. The tribological properties of 1, 2, 5 and 10 wt.% filled samples are evaluated under a normal pressure and sliding speed of 6.3 MPa and 50.8 mm/s, respectively. The wear resistance was found to improve 3000× over unfilled PTFE with the addition of 1 wt.% nanoparticles. The 5 wt.% sample had the lowest steady state wear rate of K = 1.3 × 10⁻⁷ mm³/N m and the lowest steady friction coefficient with μ = 0.21.     

Tribological behavior of NiAl matrix composites with addition of oxides at high temperatures

NiAl, NiAl–Cr–Mo alloy and NiAl matrix composites with addition of oxides (ZnO/CuO) were fabricated by powder metallurgy route. It was found that some new phases (such as NiZn₃, Cu_0.81Ni_0.19 and Al₂O₃) are formed during the fabrication process due to a high-temperature solid state reaction. Tribological behavior was studied from room temperature to 1000 °C on an HT-1000 ball-on-disk high temperature tribometer. The results indicated that NiAl had high friction coefficient and wear rate at elevated temperatures, while incorporation of Cr(Mo) not only enhanced mechanical properties evidently but also improved high temperature tribological properties. Among the sintered materials, NiAl matrix composite with addition of ZnO showed the lowest wear rate at 1000 °C, while CuO addition into NiAl matrix composite exhibited the self-lubricating performance and the best tribological properties at 800 °C.     

Tribological behaviors of Ti–6Al–4V modified by chemical methods

In order to improve the tribological properties of titanium-based implants, sodium hydroxide (NaOH), hydrogen peroxide (H₂O₂) solutions, sol–gel hydroxyapatite (HA) film, thermal treatment and combined methods of NaOH solution/HA film, H₂O₂ solution/HA film are used to modify the surfaces of Ti–6Al–4V (coded TC4). The chemical states of some typical elements in the modified surfaces were detected by means of X-ray photoelectron spectroscopy (XPS). The tribological properties of modified surfaces sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the results, complex surfaces with varied components are obtained. All the methods are effective in improving the wear resistance of Ti–6Al–4V in different degrees. Among all, the surface modified by the combined method of NaOH solution/HA film gives the best tribological performances. The friction coefficient is also greatly reduced by the modification of NaOH solution. The order of the wear resistance under 3 N is as following: Ti–NaOH–HA>Ti–NaOH>Ti–HA>Ti–H₂O₂–HA>Ti–H₂O₂ >Ti–500; under 1 N is Ti–HA, Ti–NaOH–HA>Ti–NaOH. For Ti–H₂O₂, a very low friction coefficient and long wear life over 2000 passes is obtained under 1 N. SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro–crack dominate the wear of Ti–HA; slight abrasive wear dominate the wear mechanism of Ti–NaOH and microfracture and abrasive wear for Ti–NaOH–HA and Ti–H₂O₂–HA, while the sample modified by thermal treatment is characterized by sever fracture. The superior friction reduction and wear resistance of HA films are greatly attributed to the slight plastic deformation of the film. NaOH solution is superior in improving the wear resistance and decreasing the friction coefficient under relative higher load (3 N) and H₂O₂ is helpful to reduce friction and wear under relatively lower load (1 N). Combined method of Ti–NaOH–HA is suggested to improve the wear resistance of Ti–6Al–4V for medial applications under fretting situations.     

Tribological behavior and wear mechanisms of MoSi2-base composites sliding against AA6063 alloy at elevated temperature

Intermetallic Mo(Si,Al)₂, Mo(Si,Al)₂/Al₂O₃, Mo(Si,Al)₂/SiC and Mo(Si,Al)₂/ZrO₂ composites produced by spark plasma sintering of mechanically alloyed powders were tested on a block-on-cylinder apparatus, sliding against an AA6063 alloy cylinder at elevated temperature. Abrasion, micro-fracture and surface tribochemical reactions were found to be the operative wear mechanisms, producing severe wear in the investigated alloys. Abrasive wear by pull-out of Al₂O₃ and micro-fracture of Mo(Si,Al)₂ particles promotes severe wear in the Mo(Si,Al)₂/Al₂O₃ composite. In the Mo(Si,Al)₂/SiC composites, hard SiC inclusions suppressed the abrasive wear, but a tribochemical reaction was found to be the dominant wear mechanism. A combination of abrasion by pull-out of Al₂O₃ particles and a tribochemical reaction was revealed to be the main wear mechanism in the Mo(Si,Al)₂/ZrO₂ materials. The brittleness index B = H/K_1C was applicable for prediction of the relative wear resistance. In agreement with the suggested model, the lowest wear rate, corresponding to B = 5.5–6.5 μm^−1/2, was found in the Mo(Si,Al)₂/30 vol.% SiC and Mo(Si,Al)₂/30 vol.% ZrO₂ composites.     

An investigation of friction and wear performances of bonded molybdenum disulfide solid film lubricants in fretting conditions

The friction and wear performances of bonded MoS₂ solid film lubricants with the counterpart steel ball rubbing were investigated in fretting wear conditions in order to inquire into the load-carrying capacity and wear mechanisms of bonded MoS₂ solid film lubricants under dry friction conditions. Experimental results show that the bonded MoS₂ solid film lubricants have excellent anti-friction and wear-resistance performances within a wide load range between 20 N and 800 N and within a wide oscillatory frequency range between 5 Hz and 30 Hz. It is found through analyses of the transfer films formed in the surface of the counterpart steel ball investigated by SEM, XPS and AES, that the thickness of the transfer film formed is about 38 nm and the oxidation of MoS₂ in the transfer films does not occur during dry friction process. The high load and frequency promote the formation of a compact transfer films. The compact transfer films are believed to be the predominant mechanism giving rise to high load-carrying capacity, and excellent wear-resistance performances of the bonded MoS₂ solid film lubricants.     

Friction–wear behavior and tribochemical reactions of different ceramics in HFC-134a gas

The friction and wear properties of the ionic ceramics Al₂O₃ and ZrO₂, and the covalent ceramics Si₃N₄ and SiC rubbing against an Al₂O₃ ball in vacuum (10⁻⁵ Pa) and in CF₃CH₂F (HFC-134a) gas at 10⁴ Pa were investigated using a ball-on-disk type tribometer. Without exposure to air, the surface composition and chemical state of the wear tracks and debris on the disks were determined with X-ray photoelectron spectroscopy (XPS). It is found that HFC-134a gas significantly reduces the friction and wear of all the ceramic couples, and that the ionic ceramic pairs show lower friction and wear. On the other hand, metal fluorides and/or fluorine-containing organic compounds are detected on the sliding surfaces. The differences in the friction–wear behavior of the ceramics rubbing in HFC-134a gas may be due to the products of tribochemical reactions, which are dependent on the bond type of the ceramics.     

A comparative study on the wear properties of coarse-grained Al6061 alloy and nanostructured Al6061–Al2O3 composites

Wear behavior of nanostructured Al6061 alloy and Al6061–Al₂O₃ nanocomposites produced by milling and hot consolidation were investigated. The samples were characterized by hardness test, pin-on-disk wear test, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Nanocomposites containing 3 vol% Al₂O₃ showed a maximum hardness of 235 HV and optimum wear rate of 4×10⁻³ mg/m. Increasing the amount of Al₂O₃ up to 5 vol% resulted in decrease in hardness values (∼112 HV) and a sharp rise in wear rate (∼18×10⁻³ mg/m).     

Tribological properties of γ-Y2Si2O7 ceramic against AISI 52100 steel and Si3N4 ceramic counterparts

Reciprocating ball-on-flat dry sliding friction and wear experiments have been conducted on single-phase γ-Y₂Si₂O₇ ceramic flats in contact with AISI 52100 bearing steel and Si₃N₄ ceramic balls at 5–15 N normal loads in an ambient environment. The kinetic friction coefficients of γ-Y₂Si₂O₇ varied in the range over 0.53–0.63 against AISI 52100 steel and between 0.51–0.56 against Si₃N₄ ceramic. We found that wear occurred predominantly during the running-in period and it almost ceased at the steady friction stage. The wear rates of γ-Y₂Si₂O₇ were in the order of 10^?4 mm³/(N m). Besides, wear debris strongly influenced the friction and wear processes. The strong chemical affinity between γ-Y₂Si₂O₇ and AISI 52100 balls led to a thick transfer layer formed on both contact surfaces of the flat and counterpart ball, which changed the direct sliding between the ball and the flat into a shearing within the transfer layer. For the γ-Y₂Si₂O₇/Si₃N₄ pair, a thin silica hydrate lubricant tribofilm presented above the compressed debris entrapped in the worn track and contact ball surface. This transfer layer and the tribofilm separated the sliding couple from direct contact and contributed to the low friction coefficient and wear rate.