大面积集成型a－SiC：H／a－Si：H叠层太阳电池的研制

报道了大面积（２７９０ｃｍ２）集成型ａ－ＳｉＣ：Ｈ／ａ－Ｓｉ：Ｈ叠层太阳电池的研制及稳定性实验结果，讨论了限制该电池效率的一些因素。实验电池的性能参数：Ｖｏｃ＝４０．８Ｖ，ＩＳＣ＝５３０．４０ｍＡ，ＦＦ＝４９．４％，有效面积（２２８０ｃｍ２）光电转换效率ＥＦ＝４．６９％（ＡＭ１．５，１００ｍＷｃｍ－２，２５℃）。制备出光电子学性能优良的ａ－ＳｉＣ：Ｈ薄膜及解决电池内部ｎ／Ｐ结的接触问题是提高该电池性能的关键。     

蒸发硒化法制备CIS／CdS太阳电池研究

用蒸发硒化法制作的基于ＣｕＩｎＳｅ２（ＣＩＳ）膜的ＣＩＳ／ＣｄＳ太阳电池，面积为０．１ｃｍ２和１ｃｍ２电池的转换效率分别达到７．６２％和７．２８％，５ｃｍ×６ｃｍ电池的平均效率达到６．６７％。对制备工艺及关键技术、电池性能和退火效应进行了分析探讨。     

蒸发硒化法制备了CIS／CdS太阳电池研究

用蒸发硒化法制作的基于ＣｕＩｎＳ３２（ＣＩＳ）膜的ＣＩＳ／ＣｄＳ太阳电池，面积为０．１ｃｍ＾２和１ｃｍ＾２电池的转换效率分别达到７．６２＾和７．２８％，５ｃｍ×６ｃｍ电池的平均效率达到６．６７％，对制备工艺及关键技术，电池性能和退火效应进行了分析探讨。     

SnO_2／p接触特性对a－Si太阳电池填充因子的影响

用ＰＥＣＶＤ方法制备出高电导率（～０．２ｓｃｍ－１）、宽带隙（～２．２ｅＶ）的Ｐ型微晶化硅碳合金（ｐ－μｃ－ＳｉＣ：Ｈ）薄膜材料。利用ｐ－μＣ－ＳｉＣ：Ｈ／ｐ－ａ－Ｓｉ：Ｈ复合结构做ａ－Ｓｉ太阳电池的窗口材料，明显改善了ＳｎＯ２／ｐ之间的接触特性，从而使１０ｃｍ×１０ｃｍ单结集成型电池的填充因子从０．７０以下提高到０．７２。     

400cm2 a-Si/a-Si叠层太阳电池的研究

以全部国产化装备和工业用原材料，以简单铝背电极制备出初始效率为８．２８％，经室外阳光照射一年后稳定效率为７．３５％，面积为２０ｃｍ×２０ｃｍ，有效面积为３６０ｃｍ２ａ－Ｓｉ／ａ－Ｓｉ叠层太阳电池。主要制备技术措施：（１）ＴＣＯ／ｐ界面接触特性的改善；（２）μｃ－ＳｉＣ∶Ｈ／ａ－ＳｉＣ∶Ｈ复合窗口层技术；（３）ｐ／ｉ界面Ｈ处理；（４）高质量本征ａ－Ｓｉ∶Ｈ材料；（５）优良的ｎ１／ｐ２隧道结；（６）最佳电池结构设计等。     

快速汽相沉积法制备硅薄膜太阳电池

对在重掺杂抛光单晶硅衬底上用ＲＴＣＶＤ法形成硅薄膜太阳电池进行了研究。衬底为〈１００〉晶向ｐ＋ ＋ 型重掺硅片,电阻率为５×１０－ ３Ωｃｍ 。主要工艺过程为：在衬底上生长一层硅薄膜同时掺硼,膜厚３８μｍ ,扩磷制备ｐ－ｎ 结,背面蒸Ａｌ及Ｔｉ／Ｐｄ／Ａｇ 制背电极,正表面在扩散后生长一层ＳｉＯ２ ,前面用光刻剥离法制备Ｔｉ／Ｐｄ／Ａｇ 电极,制成的１ｃｍ ２ 太阳电池,开路电压ＶＯＣ＝ ６１２．８ｍ Ｖ,短路电流ＩＳＣ＝ ２９．３ｍ Ａ,填充因子ＦＦ＝ ０．７５７９,效率η＝ １３．６１。对一些影响电池特性的因素进行了研究,发现硅薄膜的掺杂浓度、发射层的掺杂浓度以及减反射层都对太阳电池的特性有较大影响。     

P型μC－SiC：H窗口材料掺杂特性的研究

用等离子体射频辉光放电法，在低衬底温度（＜１７０℃）、小ｒｆ功率（＜６０ｍＷｃｍ２）条件下，实现了硼掺杂硅碳合金薄膜材料的微晶化。获得了暗电导率σＤ～０．２ｓｃｍ－１、光带隙宽度Ｅｏｐｔ～２．２ｅＶ的ｐ型微晶氢化硅碳合金（μＣ－Ｓｉ：Ｂ：Ｈ）薄膜。晶化的关键是Ｈ２稀释率和掺杂水平的控制。对该材料的掺杂效应、光电特性以及掺杂水平对材料结构的影响进行了详细研究。     

EBV法制备Znln2S4薄膜的性质研究

用电子束加热真空蒸发法（ＥＢＶ法）制备了厚度为３５０ｎｍ的ＺｎＩｎ２Ｓ４薄膜。研究了最佳成膜工艺条件和最新电子能谱分析结果；通过不同气氛处理可以控制材料的导电类型，典型膜的电阻率为２．５×１０＾－１Ω．ｃｍ，Ｈａｌｌ迁移率为５２ｃｍ＾２．Ｖ＾－１．ｓ＾－１，载流子浓度为１．４２×１０＾１７ｃｍ＾－３，禁带宽度为２．１３ｅＶ。探讨了ＺｎＩｎ２Ｓ４膜的导电机理，并制作了ＺｎＩｎ２Ｓ４－Ｓｉ太阳电池。     

优质氧化锌透明导电膜

报道了采用反应电子束蒸发技术制备优质氧化锌透明导电膜的工艺和结果。典型的结果：电阻率低达２×１０－４Ω．ｃｍ，霍尔电子迁移率为５２ｃｍ２（Ｖｓ）－１，厚４０００×１０－１０ｍ膜的方块电阻为８．９Ω／□，可见光透过率大于９０％。分析了源掺杂、镀膜气氛、衬底温度等参数与膜的电导和透光特性的关系。     

乙烯对纳米硅碳薄膜晶化的影响

在等离子体化学气相沉积系统中采用高氢稀释硅烷加乙烯法制备了ｎｃ－ＳｉＣｘ：Ｈ薄膜。系统研究了Ｃ２Ｈ４／（Ｃ２Ｈ４＋ＳｉＨ４）（Ｘｃ）气体流量比对ｎｃ－ＳｉＣｘ：Ｈ薄膜的晶化和其它不龟性能的影响。     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

NEXT GENERATION ENGINEERED MATERIALS FOR ULTRA SUPERCRITICAL STEAM TURBINES

正1 ABSTRACT To reduce the effect of global warming on our climate,the levels of CO2emissions should be reduced.One way to do this is to increase the efficiency of electricity production from fossil fuels.This will in turn reduce the amount of CO2emissions for a given power output.Using US practice for efficiency calculations,then a move from a typical US plant running at 37%efficiency to a 760℃/38.5 MPa(1 400/5 580 psi)plant running at 48%efficiency would reduce CO2emissions by 170kg/MW.hr or 25%.     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

Contents in Volume 23,2014

<正>~~     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。     

新型高压共轨ECU升压模块的数字化开发与优化

为了提高喷油器电磁阀的响应速率,提出了一种基于CPLD(复杂可编程逻辑器件)应用于高压共轨ECU的数字升压模块。鉴于该升压电路结构参数多,其升压电压的恢复响应要求高等特征,基于Pspice建立了升压电路的仿真模型,研究了不同电路参数下升压模块的输出特性,全面优化了该升压模块的性能。结果显示,该升压模块的最大转换效率可以达90%以上。在柴油发动机上对ECU的试验表明,升压电压最大波动不超过10%,其恢复时间仅为1.3ms,功率管最大温升仅为41℃,满足整机运行范围内ECU的需求。     

Trace metal chemistry and silicification of microorganisms in geothermal sinter, Taupo Volcanic Zone, New Zealand

As part of a pilot study investigating the role of microorganisms in the immobilisation of As, Sb, B, Tl and Hg, the inorganic geochemistry of seven different active sinter deposits and their contact fluids were characterised. A comprehensive series of sequential extractions for a suite of trace elements was carried out on siliceous sinter and a mixed silica-carbonate sinter. The extractions showed whether metals were loosely exchangeable or bound to carbonate, oxide, organic or crystalline fractions. Hyperthermophilic microbial communities associated with sinters deposited from high temperature (92–94°C) fluids at a variety of geothermal sources were investigated using SEM. The rapidity and style of silicification of the hyperthermophiles can be correlated with the dissolved silica content of the fluid. Although high concentrations of Hg and Tl were found associated with the organic fraction of the sinters, there was no evidence to suggest that any of the heavy metals were associated preferentially with the hyperthermophiles at the high temperature (92–94°C) ends of the terrestrial thermal spring ecosystems studied.     

Assessment methods of material ageing using Sdobyrev''s creep rupture model

The physical aspects of the activation energy, in higher and high temperatures, of the metal creep process were examined. The research results of creep-rupture in a uniaxial stress state and the criterion of creep-rupture in biaxial stress states, at two temperatures, are then presented. For these studies creep-rupture, taking case iron as an example the energy and pseudoenergy activation was determined. For complex stress states the criterion of creep-rupture was taken to be Sdobyrev's, i.e. σ_red = σ₁ β + (1 − β)σ_i, where: σ₁-maximal principal stress, σ_i-stress intensity, β-material constant (at variable temperature β = β(T)). The methods of assessment of the material ageing grade are given in percentages of ageing of new material in the following mechanical properties: 1) creep strength in uniaxial stress state, 2) activation energy in uniaxial stress state, 3) criterion creep strength in complex stress states, 4) activation pseudoenergy in complex stress states. The methods 1) and 3) are the relatively simplest because they result from experimental investigations only at nominal temperature of the structure work, however, for methods 2) and 4) it is necessary to perform the experimental investigations at least at two temperatures.     

Production of hydrogen from sewage biosolids in a continuously fed bioreactor: Effect of hydraulic retention time and sparging

Hydrogen was produced from primary sewage biosolids via mesophilic anaerobic fermentation in a continuously fed bioreactor. Prior to fermentation the sewage biosolids were heated to 70 °C for 1 h to inactivate methanogens and during fermentation a cellulose degrading enzyme was added to improve substrate availability. Hydraulic retention times (HRT) of 18, 24, 36 and 48 h were evaluated for the duration of hydrogen production. Without sparging a hydraulic retention time of 24 h resulted in the longest period of hydrogen production (3 days), during which a hydrogen yield of 21.9 L H₂ kg⁻¹ VS added to the bioreactor was achieved. Methods of preventing the decline of hydrogen production during continuous fermentation were evaluated. Of the techniques evaluated using nitrogen gas to sparge the bioreactor contents proved to be more effective than flushing just the headspace of the bioreactor. Sparging at 0.06 L L min⁻¹ successfully prevented a decline in hydrogen production and resulted in a yield of 27.0  L H₂ kg⁻¹ VS added, over a period of greater than 12 days or 12 HRT. The use of sparging also delayed the build up of acetic acid in the bioreactor, suggesting that it serves to inhibit homoacetogenesis and thus maintain hydrogen production.