Effect of cultivation mode on microalgal growth and CO2 fixation

The biofixation of carbon dioxide (CO₂) by marine microalgae cultivation has been regarded as one of the potential to diminish the greenhouse effect and produce the biomass. To compare and select the high efficiency cultivation mode, the effect of two different cultivation modes on the performances of growth and CO₂ biofixation from air for energy marine microalgae Chlorella sp. was determined in this work. In one mode the microalga was cultivated using static (open) method and in the other mode it was cultivated using aerated (closed) method. It was found that, under the experimental conditions, the specific growth rate and CO₂ fixation rate of the aerated (closed) cultivation were 0.5121 (d⁻¹) and 1.3784 g CO₂/l d, and are 1.78 and 5.39 times that of the static (open) cultivation, respectively. In addition, the effects of pH value and dissolved oxygen (DO) concentration of the culture medium were analyzed and compared in two cultivation modes. The result indicates the aerated (closed) mode can effectively enhance the performance on microalgal growth and CO₂ biofixation.     

CO2 capture by adsorption with nitrogen enriched carbons

The success of CO₂ capture with solid sorbents is dependent on the development of a low cost sorbent with high CO₂ selectivity and adsorption capacity. Immobilised amines are expected to offer the benefits of liquid amines in the typical absorption process, with the added advantages that solids are easy to handle and that they do not give rise to corrosion problems. In this work, different alkylamines were evaluated as a potential source of basic sites for CO₂ capture, and a commercial activated carbon was used as a preliminary support in order to study the effect of the impregnation. The amine coating increased the basicity and nitrogen content of the carbon. However, it drastically reduced the microporous volume of the activated carbon, which is chiefly responsible for CO₂ physisorption, thus decreasing the capacity of raw carbon at room temperature.     

Development of low-cost biomass-based adsorbents for postcombustion CO2 capture

In this work a series of carbon adsorbents were prepared from a low-cost biomass residue, olive stones. Two different approaches were studied: activation with CO₂ and heat treatment with gaseous ammonia. The results showed that both methods are suitable for the production of adsorbents with a high CO₂ adsorption capacity, and their potential application in VSA or TSA systems for postcombustion CO₂ capture. It was found that the presence of nitrogen functionalities enhances CO₂ adsorption capacity, especially at low partial pressures.     

Adsorption characteristics of metal ions by CO2-fixing Chlorella sp. HA-1

Single and binary metal systems were employed to investigate the removal characteristics of Pb²⁺, Cu²⁺, Cd²⁺, and Zn²⁺ by Chlorella sp. HA-1 that were isolated from a CO₂ fixation process. Adsorption test of single metal systems showed that the maximum metal uptakes were 0.767 mmol Pb²⁺, 0.450 mmol Cd²⁺, 0.334 mmol Cu²⁺ and 0.389 mmol Zn²⁺ per gram of dry cell. In the binary metal systems, the metal ions on Chlorella sp. HA-1 were adsorbed selectively according to their adsorption characteristics. Pb²⁺ ions significantly inhibited the adsorption of Cu²⁺, Zn²⁺, and Cd²⁺ ions, while Cu²⁺ ions decreased remarkably the metal uptake of Cd²⁺ and Zn²⁺ ions. The relative adsorption between Cd²⁺ and Zn²⁺ ions was reduced similarly by the presence of the other metal ions.     

Extraction of nimbin from neem seeds using supercritical CO2 and a supercritical CO2–methanol mixture

Nimbin, a component found in neem seeds, which is reported to have several valuable medicinal properties including: anti-inflammatory, anti-pyretic, anti-fugal, antihistamine and antiseptic was extracted from neem seeds using supercritical CO₂ and CO₂ with a methanol modifier.Nimbin extraction yields using supercritical carbon dioxide were found to be approximately 85% at 308 K, 23 MPa and a CO₂ flow rate of 0.62 cm³/min for a 2-g sample of neem. An optimum extraction pressure appears to exist at ≈23 MPa and 328 K. Although extraction using a methanol modifier did improve the extraction somewhat, methanol was not found to be an effective modifier for extracting nimbin.Dynamic extraction curves were predicted using three empirical models and a theoretical model. The three empirical models were: a Langmuir gas adsorption model, a first order plus dead time (FOPDT) model and a so-called tⁿ cyclone model used to incorporate sigmoidal curves. The parameters in the empirical models were fitted to the experimental data. The Goto et al. [J. Chem. Eng. Jpn. 31 (1998) 171] theoretical model was compared to the experimental results and was found to fit the data well. The theoretical model shows that the extraction yield depends strongly on the solvent flow rate, that is, external mass transfer or equilibrium is the controlling step of this process.     

Simultaneous easy CO2 recovery and drastic reduction of SOx and NOx in O2/CO2 coal combustion with heat recirculation

Coal combustion with O₂/CO₂ is promising because of its easy CO₂ recovery, extremely low NO_x emission and high desulfurization efficiency. Based on our own fundamental experimental data combined with a sophisticated data analysis, its characteristics were investigated. It was revealed that the conversion ratio from fuel-N to exhausted NO in O₂/CO₂ pulverized coal combustion was only about one fourth of conventional pulverized coal combustion. To decrease exhausted NO further and realize simultaneous easy CO₂ recovery and drastic reduction of SO_x and NO_x, a new scheme, i.e. O₂/CO₂ coal combustion with heat recirculation, was proposed. It was clarified that in O₂/CO₂ coal combustion, with about 40% of heat recirculation, the same coal combustion intensity as that of coal combustion in air could be realized even at an O₂ concentration of as low as 15%. Thus exhausted NO could be decreased further into only one seventh of conventional coal combustion. Simultaneous easy CO₂ recovery and drastic reduction of SO_x and NO_x could be realized with this new scheme.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Modeling and simulation for the methane steam reforming enhanced by in situ CO2 removal utilizing the CaO carbonation for H2 production

The transient behavior of catalytic methane steam reforming (MSR) coupled with simultaneous carbon dioxide removal by carbonation of CaO pellets in a packed bed reactor for hydrogen production has been analyzed through a mathematical model with reaction experiments for model verification. A dynamic model has been developed to describe both the MSR reaction and the CaO carbonation-enhanced MSR reaction at non-isothermal, non-adiabatic, and non-isobaric operating conditions assuming that the rate of the CaO carbonation in a local zone of the packed bed is governed by kinetic limitation or by mass transfer limitation of the reactant CO₂. Apparent carbonation kinetics of the CaO pellet prepared has been determined using the TGA carbonation experiments at various temperatures, and incorporated into the model. The resulting model is shown to successfully depict the transient behavior of the in situ CaO carbonation-enhanced MSR reaction. The effects of major operating parameters on the transient behavior of the CaO carbonation-enhanced MSR have been investigated using the model. The bed temperature is the most important parameter for determining the amount of CO₂ removed by carbonation of CaO, and at temperatures of 600°C, 650°C, 700°C and 750°C, the CO₂ uptake is 1.43, 2.29, 3.5 and -CO₂/kg-CaO, respectively. Simultaneously with the increase in CO₂ uptake with increasing temperature, the corresponding amounts of hydrogen produced are 1.56, 2.54, 3.91 and -H₂/kg-CaO, at the same temperatures as above. Operation at high pressure, high steam to methane feed ratio, and the decreased feed rate at a given temperature are favorable for increasing the degree of the overall utilization of CaO pellets in the reactor bed, and for lowering the CO concentration in the product.     

Photoinduced activation of CO2 on TiO2 surfaces: Quantum chemical modeling of CO2 adsorption on oxygen vacancies

Chemical processes that utilize CO₂ emissions from coal-fired power plants will be required as the world progresses towards reducing CO₂ emissions. The conversion of CO₂ using light energy (CO₂ photoreduction) has the potential to produce useful fuels or valuable chemicals while decreasing CO₂ emissions from the use of fossil fuels such as coal. Computational studies on the initial steps of photoinduced CO₂ activation on TiO₂ surfaces, necessary to develop a mechanistic understanding of CO₂ photoreduction are a focus of this article.The results from previous quantum mechanical modeling studies conducted by the authors indicated that stoichiometric TiO₂ surfaces likely do not promote electron transfer to CO₂. Therefore, the role of oxygen vacancies in promoting the light-induced conversion of CO₂ (CO₂ photoreduction) on TiO₂ surfaces was examined in this study. Two different side-on bonded bent-CO₂ (bridging Ti-CO₂^δ•−-Ti species) were formed on the reduced rutile (110) and anatase (010), (001) surfaces, indicating charge transfer from the reduced surface to CO₂. Further steps in the photoexcitation of these bent-CO₂ species were investigated with density functional theory calculations. Consistent with CO₂ adsorption and photodesorption on other n-type metal oxides such as ZrO₂, the results suggest that the bent-CO₂ species do not gain further charge from the TiO₂ surface under illumination and are likely photodesorbed as neutral species. Additionally, although the formation of species such as CO and HCHO is thermodynamically possible, the energy needed to regenerate the oxygen vacancy on TiO₂ surfaces (~ 7 eV) is greater than that available through band-gap illumination (3.2 eV). Therefore, CO₂ reactions with water on irradiated anatase TiO₂ surfaces are likely to be stoichiometric.     

Thermodynamic performance of O2/CO2 gas turbine cycle with chemical recuperation by CO2-reforming of methane

This paper proposes a novel power cycle system composed of chemical recuperative cycle with CO₂–NG (natural gas) reforming and an ammonia absorption refrigeration cycle. In which, the heat is recovered from the turbine exhaust to drive CO₂–NG reformer firstly, and then lower temperature heat from the turbine exhaust is provided with the ammonia absorption refrigeration system to generate chilled media, which is used to cool the turbine inlet gas except export. In this paper, a detailed thermodynamic analysis is carried out to reveal the performance of the proposed cycle and the influence of key parameters on performance is discussed. Based on 1 kg s⁻¹ of methane feedstock and the turbine inlet temperature of 1573 K, the simulation results shown that the optimized net power generation efficiency of the cycle rises up to 49.6% on the low-heating value and the exergy efficiency 47.9%, the new cycle system reached the net electric-power production 24.799 MW, the export chilled load 0.609 MW and 2.743 kg s⁻¹ liquid CO₂ was captured, achieved the goal of CO₂ and NO_x zero-emission.     

CO oxidation and CO2 reduction on carbon supported PtWO3 catalyst

The activity of a carbon supported PtWO₃ (PtWO₃/C) catalyst in the CO oxidation and CO₂ reduction reactions was evaluated in sulfuric acid solution at room temperature.Cyclic voltammetry combined with on-line mass spectrometry shows that the oxidation of both saturated CO adlayer and dissolved CO on PtWO₃/C material commences at rather low potentials, ca. 0.18 and 0.12 V vs. RHE, respectively. However, the low-potential process seems to involve only a minor fraction of the CO adlayer, the major part of the adsorbed CO layer being oxidised at the potentials as high as those for pure Pt catalysts—ca. 0.7 V vs. RHE. PtWO₃/C material was found to reversibly de-activate upon a prolonged exposure to the CO-saturated solution due to the inhibition of the hydrogen tungsten bronze formation.The reduction of CO₂ on PtWO₃/C leads to the formation of an adsorbate - presumably CO - on the Pt sites of the catalyst. Although the rate of the adsorbate build-up on PtWO₃/C at 0.1 V is lower than that on pure Pt/C, our results indicate that upon a prolonged exposure of the PtWO₃/C electrode to a CO₂-saturated solution a complete poisoning of the Pt sites with the adsorbate is likely to occur at room temperature.     

CO2 capture using some fly ash-derived carbon materials

Adsorption is considered to be one of the more promising technologies for capturing CO₂ from flue gases. For post-combustion capture, the success of such an approach is however dependent on the development of an adsorbent that can operate competitively at relatively high temperatures. In this work, low cost carbon materials derived from fly ash, are presented as effective CO₂ sorbents through impregnation these with organic bases, for example, polyethylenimine aided by polyethylene glycol. The results show that for samples derived from a fly ash carbon concentrate, the CO₂ adsorption capacities were relatively high (up to 4.5 wt%) especially at high temperatures (75 °C), where commercial active carbons relying on physi-sorption have low capacities. The addition of PEG improves the adsorption capacity and reduces the time taken for the sample to reach the equilibrium. No CO₂ seems to remain after desorption, suggesting that the process is fully reversible.     

Adsorption of CO2 and SO2 on activated carbons with a wide range of micropore size distribution

The adsorption isotherms of N₂ at 77K, CO₂ at 251, 273 and 298K, and SO₂ at 262 and 273K have been determined on a series of physically activated carbons with a wide range of micropore size distributions. Since the series includes carbons with very high burn-off, it shows the problems involved in the characterization of microporsity in superactivated carbons. On the other hand, the results show that the carbon surface-adsorbate interactions for SO₂ at low relative pressures are weaker than for N₂ and CO₂, as a result of the strong adsorptive-adsorptive interactions in the bulk gas phase.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

High-pressure sorption isotherms and sorption kinetics of CH4 and CO2 on coals

Using a manometric experimental setup, high-pressure sorption measurements with CH₄ and CO₂ were performed on three Chinese coal samples of different rank (VR_r = 0.53%, 1.20%, and 3.86%). The experiments were conducted at 35, 45, and 55 °C with pressures up to 25 MPa on the 0.354-1 mm particle fraction in the dry state. The objective of this study was to explore the accuracy and reproducibility of the manometric method in the pressure and temperature range relevant for potential coalbed methane (CBM) and CO₂-enhanced CBM (CO₂-ECBM) activities (P > 8 MPa, T > 35 °C). Maximum experimental errors were estimated using the Gauss error propagation theorem, and reproducibility tests of the high-pressure sorption measurements for CH₄ and CO₂ were performed. Further, the experimental data presented here was used to explicitly study the CO₂ sorption behaviour of Chinese coal samples in the elevated pressure range (up to 25 MPa) and the effects of temperature on supercritical CO₂ sorption isotherms.The experiments provided characteristic excess sorption isotherms which, in the case of CO₂ exhibit a maximum around the critical pressure and then decline and level out towards a constant value. The results of these manometric tests are consistent with those of previous gravimetric sorption studies and corroborate a crossover of the 35, 45, and 55 °C CO₂ excess sorption isotherms in the high-pressure range. The measurement range could be extended, however, to significantly higher pressures. The excess sorption isotherms tend to converge, indicating that the temperature dependence of CO₂ excess sorption on coals at high-pressures (>20 MPa) becomes marginal. Further, all CO₂ high-pressure isotherms measured in this study were approximated by a three-parameter excess sorption function with special consideration of the density ratio of the “free” phase and the sorbed phase. This function provided a good representation of the experimental data.The maximum excess sorption capacity of the three coal samples for methane ranged from 0.8 to 1.6 mmol/g (dry, ash-free) and increased from medium volatile bituminous to subbituminous to anthracite. The medium volatile bituminous coal also exhibited the lowest overall excess sorption capacity for CO₂. However, the subbituminous coal was found to have the highest CO₂ sorption capacity of the three samples. The mass fraction of adsorbed substance as a function of time recorded during the first pressure step was used to analyze the kinetics of CH₄ and CO₂ sorption on the coal samples. CO₂ sorption proceeds more rapidly than CH₄ sorption on the anthracite and the medium volatile bituminous coal. For the subbituminous coal, methane sorption is initially faster, but during the final stage of the measurement CO₂ sorption approaches the equilibrium value more rapidly than methane.     

The electronic effects of Pr on La1−xPrxNiAl11O19 for CO2 reforming of methane

The CO₂ reforming of CH₄ to synthesis gas by using praseodymium modified hexaaluminate La_1−xPr_xNiAl₁₁O₁₉ (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0) as catalysts was studied. The modifier Pr improved the reducibility and catalytic activity of Ni ions as active component in the hexaaluminate lattices, especially the conversion of CH₄ and CO₂ reached 89.62% and 92.94%, respectively over La_0.8Pr_0.2NiAl₁₁O₁₉. It was found that the addition of Pr can promote the electronic transformation between the Ni ions and the La ions to maintain Ni at a lower valence, which promotes the activation of CH₄.     

Experimental study of CO2 absorption/stripping via PVDF hollow fiber membrane contactor

Gas–liquid hollow fiber membrane contactor can be a promising alternative for the CO₂ absorption/stripping due to the advantages over traditional contacting devices. In this study, the structurally developed hydrophobic polyvinylidene fluoride (PVDF) hollow fiber membranes were prepared via a wet spinning method. The membranes were characterized in terms of morphology, permeability, wetting resistance, overall porosity and mass transfer resistance. From the morphology analysis, the membranes demonstrated a thin outer finger-like layer with ultra thin skin and a thick inner sponge-like layer without skin. The characterization results indicated that the membranes possess a mean pore size of 9.6 nm with high permeability and wetting resistance and low mass transfer resistance (1.2 × 10⁴ s/m). Physical CO₂ absorption/stripping were conducted through the fabricated gas–liquid membrane contactor modules, where distilled water was used as the liquid absorbent. The liquid phase resistance was dominant due to significant change in the absorption/stripping flux with the liquid velocity. The CO₂ absorption flux was approximately 10 times higher than the CO₂ stripping flux at the same operating condition due to high solubility of CO₂ in water as confirmed with the effect of liquid phase pressure and temperature on the absorption/stripping flux.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

Effect of H2S on the CO2 corrosion of carbon steel in acidic solutions

The objective of this study is to evaluate the effect of low-level hydrogen sulfide (H₂S) on carbon dioxide (CO₂) corrosion of carbon steel in acidic solutions, and to investigate the mechanism of iron sulfide scale formation in CO₂/H₂S environments. Corrosion tests were conducted using 1018 carbon steel in 1 wt.% NaCl solution (25 °C) at pH of 3 and 4, and under atmospheric pressure. The test solution was saturated with flowing gases that change with increasing time from CO₂ (stage 1) to CO₂/100 ppm H₂S (stage 2) and back to CO₂ (stage 3). Corrosion rate and behavior were investigated using linear polarization resistance (LPR) technique. Electrochemical impedance spectroscopy (EIS) and potentiodynamic tests were performed at the end of each stage. The morphology and compositions of surface corrosion products were analyzed using scanning electron microscopy (SEM)/energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The results showed that the addition of 100 ppm H₂S to CO₂ induced rapid reduction in the corrosion rate at both pHs 3 and 4. This H₂S inhibition effect is attributed to the formation of thin FeS film (tarnish) on the steel surface that suppressed the anodic dissolution reaction. The study results suggested that the precipitation of iron sulfide as well as iron carbonate film is possible in the acidic solutions due to the local supersaturation in regions immediately above the steel surface, and these films provide corrosion protection in the acidic solutions.     

Comparison of solvent performance for CO2 capture from coal-derived flue gas: A pilot scale study

The performance of a proprietary solvent (CAER-B2), an amine-carbonate blend, for the absorption of CO₂ from coal-derived flue gas is evaluated and compared with state-of-the-art 30 wt% monoethanolamine (MEA) under similar experimental conditions in a 0.1 MWth pilot plant. The evaluation was done by comparing the carbon capture efficiency, the overall mass transfer rates, and the energy of regeneration of the solvents. For similar carbon loadings of the solvents in the scrubber, comparable mass transfer rates were obtained. The rich loading obtained for the blend was 0.50 mol CO₂/mol amine compared to 0.44 mol CO₂/mol amine for MEA. The energy of regeneration for the blend was about 10% lower than that of 30 wt% MEA. At optimum conditions, the blend shows promise in reducing the energy penalty associated with using industry standard, MEA, as a solvent for CO₂ capture.