Isothermal Section of the Al-Mn-Dy System at 500 °C

Phase relationships in the Al-Mn-Dy ternary system at 500 °C have been investigated by X-ray diffraction, scanning electron microscopy with energy dispersive spectroscopy, and electron probe microanalysis. From the experimental results it was concluded that the isothermal section consists of 16 single-phase regions, 26 two-phase regions and 12 three-phase regions. Two extensive solid solutions, (Al _x Mn_1?x )₁₂Dy and (Al_1?x Mn _x )₂Dy, were observed. The solid solution (Al _x Mn_1?x )₁₂Dy forms by Al replacing Mn in Mn₁₂Dy, while the continuous solid solution (Al_1?x Mn _x )₂Dy forms by Mn and Al mutually substituting in Al₂Dy and Mn₂Dy, respectively. The maximum solid solubility of Al in Mn₁₂Dy is 79.3 at.%.     

Microstructure and mechanical properties of multi-principal component AlCoCrFeNiCu<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> alloy

By introducing Cu, AlCoCrFeNiCu _x (x values in molar ratio, x = 0, 0.1, 0.5, 1.0, 1.5, 2.0, and 2.5) alloys were designed and prepared. The effects of Cu on microstructure and properties of AlCoCrFeNi alloy were investigated. The introduction of Cu results in the formation of Cu-rich FCC solid solution phase when Cu content is low. There are two FCC solid solution phases, i.e., Cu-rich FCC solid solution phase and phase transformation-induced FCC solid solution phase, when the Cu content is more than 1.0. Both the yield stress and plastic strain of alloy show a turning point when the Cu content is 0.5. Among the seven alloys, Cu_0.5 alloy exhibits the largest yield stress of 1187 MPa and the lowest plastic strain of 16.01 %.     

Phase transformations during deformation of Fe-Ni and Fe-Mn alloys produced by mechanical alloying

Compositions of Fe_{(100 ? x)}Mn _x (x = 10 and 12 at. %) and Fe_{(100 ? y)}Ni _y (y = 18 and 20 at. %) were produced by combined mechanical alloying of pure-metal powders and annealed in the austenitic field. After annealing and cooling to room temperature, the alloys had a single-phase austenitic structure. During deformation, the γ phase partially transforms into the α ₂ phase (and/or ? phase in Fe-Mn alloys). The phase composition of the alloys after deformation depends on the amount of alloying elements and the predeformation annealing regime. The amount of martensite in the structure of a bulk alloy obtained by powder compacting grows proportionally to the degree of deformation of the sample.     

Optimum Combination of Thermoplastic Formability and Electrical Conductivity in Al–Ni–Y Metallic Glass

Both thermoplastic formability and electrical conductivity of Al–Ni–Y metallic glass with 12 different compositions have been investigated in the present study with an aim to apply as a functional material, i.e. as a binder of Ag powders in Ag paste for silicon solar cell. The thermoplastic formability is basically influenced by thermal stability and fragility of supercooled liquid which can be reflected by the temperature range for the supercooled liquid region (ΔT_x) and the difference in specific heat between the frozen glass state and the supercooled liquid state (ΔC_p). The measured ΔT_x and ΔC_p values show a strong composition dependence. However, the composition showing the highest ΔT_x and ΔC_p does not correspond to the composition with the highest amount of Ni and Y. It is considered that higher ΔT_x and ΔC_p may be related to enhancement of icosahedral SRO near T_g during cooling. On the other hand, electrical resistivity varies with the change of Al contents as well as with the change of the volume fraction of each phase after crystallization. The composition range with the optimum combination of thermoplastic formability and electrical conductivity in Al–Ni–Y system located inside the composition triangle whose vertices compositions are Al₈₇Ni₃Y₁₀, Al₈₅Ni₅Y₁₀, and Al₈₆Ni₅Y₉.     

Microstructure,Phase Occurrence,and Corrosion Behavior of As-Solidified and As-Annealed Al-Pd Alloys

In the present work, we studied the microstructure, phase constitution, and corrosion performance of Al₈₈Pd₁₂, Al₇₇Pd₂₃, Al₇₂Pd₂₈, and Al₆₇Pd₃₃ alloys (metal concentrations are given in at.%). The alloys were prepared by repeated arc melting of Al and Pd granules in argon atmosphere. The as-solidified samples were further annealed at 700 °C for 500 h. The microstructure and phase constitution of the as-solidified and as-annealed alloys were studied by scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray diffraction. The alloys were found to consist of (Al), ε _n (~ Al₃Pd), and δ (Al₃Pd₂) in various fractions. The corrosion testing of the alloys was performed in aqueous NaCl (0.6 M) using a standard 3-electrode cell monitored by potentiostat. The corrosion current densities and corrosion potentials were determined by Tafel extrapolation. The corrosion potentials of the alloys were found between ? 763 and ? 841 mV versus Ag/AgCl. An active alloy dissolution has been observed, and it has been found that (Al) was excavated, whereas Al in ε _n was de-alloyed. The effects of bulk chemical composition, phase occurrence and microstructure on the corrosion behavior are evaluated. The local nobilities of ε _n and δ are discussed. Finally, the conclusions about the alloy’s corrosion resistance in saline solutions are provided.     

Co-Cu alloys produced by mechanical alloying of powder precursors characterized by different contact surface and energy excess

Co-Cu alloys were prepared by mechanical alloying using different reaction mixtures (mechanical mixture of Co and Cu powders, composite powders (Co_{(100 ? y)}P_(y))_{100 ? x} /Cu _x with a crystalline core, and composite powders (Co_{(100 ? y)}P_(y))_{100 ? x} /Cu _x with an amorphous core). The use of a complex of structural and magnetostructural methods showed that these alloys are nonuniform nanocomposite materials consisting of two phases, namely, copper- and cobalt-based solid solutions. During the mechanical alloying of the composite powders, parameters that are sensitive to the short-range-order structure of both phases were found to be changed, namely, the lattice parameter in the Cu-based solid solution as determined from X-ray diffraction patterns, and the Bloch constant that is sensitive to the short-range order in the Co-based solid solution change. In the alloys prepared by mechanical alloying of composite powders with an amorphous core, the lattice parameter a and the Bloch constant B reach values corresponding to metastable Co_{100 ? x} Cu _x solid solutions in milling times of 1.5–2.0 h. These times are lower by 1–2 orders of magnitude than the typical times that are necessary for forming metastable Co-Cu solid solutions by standard methods of mechanical alloying from mixtures of powders.     

Phase transformations in the hematite-metal system during mechanical alloying

Mössbauer spectroscopy and X-ray diffraction are used to show that the phase transformations in hematite α-Fe₂O₃-metal (M = Fe, Ni, Ti, Zr) powder mixtures induced by severe cold plastic deformation in ball mills occur via the formation of M-Fe-O solid solutions, redox reactions with the reduction of metallic iron, and the formation of secondary M _x O _y oxides and M _x Fe _y intermetallics. Mechanical activation in a ball mill is compared to that under high-pressure shear in Bridgman anvils. The transformations that take place in a ball mill are found to have several stages and to be accelerated.     

Properties of the Ti<Subscript>40</Subscript>Zr<Subscript>10</Subscript>Cu<Subscript>36</Subscript>Pd<Subscript>14</Subscript> BMG Modified by Sn and Nb Additions

The results of investigation of the influence of additions of 2 and 3 at.% of Sn and simultaneously of Sn and 3 at.% Nb on microstructure and properties of the bulk metallic glasses of composition (Ti₄₀Cu_36?x Zr₁₀Pd₁₄Sn _x )_100?y Nb _y are reported. It was found that the additions of Sn increased the temperatures of glass transition (T _g), primary crystallization (T _x ), melting, and liquidus as well as supercooled liquid range (ΔT) and glass forming ability (GFA). The nanohardness and elastic modulus decreased in alloys with 2 and 3 at.% Sn additions, revealing similar values. The 3 at.% Nb addition to the Sn-containing amorphous phase decreased as well all the T _g, T _x , T _L, and T _m temperatures as ΔT and GFA; however, relatively larger values of this parameters in alloys containing larger Sn content were preserved. In difference to the previously published results, in the case of the amorphous alloys containing small Nb and Sn additions, a noticeable amount of the quenched-in crystalline phases was not confirmed, at least of the micrometric sizes. In the case of the alloys containing Sn or both Sn and Nb, two slightly different amorphous phase compositions were detected, suggesting separation in the liquid phase. Phase composition of the alloys determined after amorphous phase crystallization was similar for all compositions. The phases Cu₈Zr_3, CuTiZr, and Pd₃Zr were mainly identified in the proportions dependent on the alloy compositions.     

Phase Equilibria in the Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript>–InSb System

The phase diagram of the (Sb₂Te₃)_100?x –InSb _x system was determined based on x-ray diffraction (XRD) analysis, differential thermal analysis (DTA), and microhardness and density measurements. An intermediate compound with composition Sb₂Te₃·2InSb was formed as a result of syntectic reaction, melting incongruently at 553 °C. This compound has tetragonal lattice with unit cell parameters of a = 4.3937 Å, b = 4.2035 Å, c = 3.5433 Å, α = 93.354°, and β = γ = 90°. Sb₂Te₃·(2 + δ)InSb (?1 ≤ δ ≤ +1) and (Sb₂Te₃)_100?x (InSb) _x (90 ≤ x ≤ 100) solid solutions exist in the investigated system, based on the intermediate compound Sb₂Te₃·2InSb and on InSb, respectively. Also, two invariant equilibria exist in the system, with eutectic point coordinates at compositions of x = 60 and x ≈ 85 mol% InSb and eutectic temperatures of T _E = 541 and T _E ≈ 501 °C, respectively.     

Evolution of structural changes in nanocrystalline alloys with temperature

Structural features of the NANOPERM-type alloys Fe_{91 ? x} Mo₈Cu₁B _x with x = 12, 15, and 17 have been investigated by Mössbauer spectroscopy. The room-temperature Mössbauer spectra of the as-quenched alloys are characteristic of disordered structural arrangement, but traces of bcc-Fe(Mo) as well as a FeMo₂B₂ phase have been revealed by X-ray diffraction in all the samples. These results have been confirmed by conversion-electron Mössbauer spectroscopy. The differences between the opposite sides of the ribbon-shaped samples have been shown to stem from structural distinctions. From the point of view of hyperfine interactions, the x = 12 sample exhibits paramagnetic behavior. With increasing x, a contribution from ferromagnetic regions appears gradually, thus leading to an increase in the magnetic ordering temperature in the as-quenched state. Partially crystallized samples have been prepared by controlled annealing of the original precursors for one hour at temperatures ranging from 330 to 650°C in a vacuum. The temperature of the onset of crystallization has been determined to be of 430, 450, and 470°C for x = 12, 15, and 17, respectively. During the first step of crystallization, bcc-Fe(Mo) nanosized grains are formed. Surface features of the samples investigated have also been characterized by using atomic force microscopy.     

Correlation between the Hall Resistance and Magnetoresistance in the Mixed State of an Nd<Subscript>2 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ce<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>CuO<Subscript>4 + δ</Subscript> Electronic Superconductor

The Hall resistance and the magnetoresistance in the mixed state of the Nd_{2 ? x}Ce _x CuO_{4 + δ} quasi-two-dimensional system near the antiferromagnetic-superconductor (AF-SC) phase transition have been measured at doping levels x = 0.14 and 0.15, and a correlation has been established. This correlation can be analyzed using the following power relationship: ρ _xy (B) ~ [ρ _xx (B)]^β. It was found that index β varied from 0.94 ± 0.03 in the region of AF and SC coexistence (x = 0.14) to 0.6 ± 0.1 in the SC region with the maximum critical temperature (x = 0.15) at low temperatures and weak magnetic fields. This reduction suggests that the symmetry of carrier pairing changes at the boundary of the transition from the phase of antiferromagnetic ordering and spin density waves to the superconducting phase in the presence of antiferromagnetic spin fluctuations.     

Structure,magnetic and magnetocaloric properties of nonstoichiometric TbCo<Subscript>2</Subscript>Ni<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> compounds

The structure and magnetic and magnetocaloric properties of new nonstoichiometric TbCo₂Ni _x compounds (0 ≤ x ≤ 0.4) have been studied. The alloys with х ≤ 0.1 have been shown to be single-phase with the MgCu₂-type structure; in alloys with х > 0.1, an additional phase with a PuNi₃-type structure has been formed. It has been found that the concentration dependences of the Curie temperature and magnetic moment of the 3d-metal sublattice have a maximum at x = 0.025. The magnetocaloric effect magnitude for the TbCo2Nix compounds has been estimated using the results of magnetic and heat-capacity measurements.     

Superior Mechanical Properties of AlCoCrFeNiTi<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> High-Entropy Alloys upon Dynamic Loading

High-entropy alloys with composition of AlCoCrFeNiTi _x (x: molar ratio; x = 0, 0.2, 0.4) under quasi-static and dynamic compression exhibit excellent mechanical properties. A positive strain-rate sensitivity of yield strength and the strong work-hardening behavior during plastic flows dominate upon dynamic loading in the present alloy system. The constitutive relationships are extracted to model flow behaviors by employing the Johnson-Cook constitutive model. Upon dynamic loading, the ultimate strength and fracture strain of AlCoCrFeNiTi _x alloys are superior to most of bulk metallic glasses and in situ metallic glass matrix composites.     

Microstructures,Martensitic Transformation,and Mechanical Behavior of Rapidly Solidified Ti-Ni-Hf and Ti-Ni-Si Shape Memory Alloys

In this work, the microstructure and mechanical properties of rapidly solidified Ti_50?x/2Ni_50?x/2Hf _x (x = 0, 2, 4, 6, 8, 10, and 12 at.%) and Ti_50?y/2Ni_50?y/2Si _y (y = 1, 2, 3, 5, 7, and 10 at.%) shape memory alloys (SMAs) were investigated. The sequence of the phase formation and transformations in dependence on the chemical composition is established. Rapidly solidified Ti-Ni-Hf or Ti-Ni-Si SMAs are found to show relatively high yield strength and large ductility for specific Hf or Si concentrations, which is due to the gradual disappearance of the phase transformation from austenite to twinned martensite and the predominance of the phase transformation from twinned martensite to detwinned martensite during deformation as well as to the refinement of dendrites and the precipitation of brittle intermetallic compounds.     

Influence of Nb on microstructure and mechanical properties of Ti-Sn ultrafine eutectic alloy

In this study, A series of the high strength (T₈₂Sn₁₈)_100-xNb_x (x=0, 1, 3, 5, and 9 at%) ultrafine eutectic alloys with large plasticity are developed by suction casting method. The Ti₈₂Sn₁₈ binary eutectic alloy consists of a mixture of a hcp Ti₃Sn and a α-Ti phases having the plate-like lamellar type duplex structure with micro scaled eutectic colony. From the (T₈₂Sn₁₈)₉₇Nb₃, the alloy display structural heterogeneous distribution of ultrafine-scaled phases composed of β-Ti(Nb) solid solution surrounded by alternating plate-like shaped Ti₃Sn and α-Ti phases. With increasing Nb content, the volume fraction of β-Ti is continuously increased, which induced improving mechanical properties both strength and plasticity. Especially, (Ti₈₂Sn₁₈)₉₁Nb₉ alloy has the outstanding combination of the high strength (σ _y ≈1.1 GPa) and large plasticity (ε _p ≈36%) at room temperature.     

Composition dependences of thermodynamical properties associated with Pb-free ternary,quaternary, and quinary solder systems

In the present study, Chou’s General Solution Model (GSM) has been used to predict the enthalpy and partial enthalpies of mixing of the liquid Ag–In–Sn ternary, Ag–In–Sn–Zn quaternary, and Ag–Au–In–Sn–Zn quinary systems. These are of technical importance to optimize lead-free solder alloys, in selected cross-sections: x_In/x_Sn = 0.5/0.5 (ternary), Au–In_0.1–Sn_0.8–Zn_0.1, Ag–In_0.1–Sn_0.8–Zn_0.1 (quaternary), and t = x_Au/x_In = 1, x_In = x_Sn = x_Zn (quinary) at 1173, 773, and 773 K, respectively. Moreover, the activity of In content in the ternary alloy system Ag–In–Sn has been calculated and its result is compared with that determined from the experiment, while the activities of Ag contents associated with the alloys mentioned above have been calculated. The other traditional models such as of Colinet, Kohler, Muggianu, Toop, and Hillert are also included in calculations. Comparing those calculated from the proposed GSM with those determined from experimental measurements, it is seen that this model becomes considerably realistic in computerization for estimating thermodynamic properties in multicomponent systems.     

Microstructure and Room-Temperature Mechanical Properties of FeCrMoVTi<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> High-Entropy Alloys

FeCrMoVTi _x (x values represent the molar ratio, where x = 0, 0.5, 1.0, 1.5, and 2.0) high-entropy alloys were prepared by a vacuum arc melting method. The effects of Ti element on the microstructure and room-temperature mechanical properties of the as-cast FeCrMoVTi _x alloys were investigated. The results show that the prepared alloys exhibited typical dendritic microstructure and the size of the microstructure became fine with increasing Ti content. The FeCrMoV alloy exhibited a single body-centered cubic structure (BCC1) and the alloys prepared with Ti element exhibited BCC1 + BCC2 mixed structure. The new BCC2 phase is considered as (Fe, Ti)-rich phase and was distributed in the dendrite region. With the increase of Ti content, the volume fraction of the BCC2 phase increased and its shape changed from a long strip to a network. For the FeCrMoV alloy, the fracture strength, plastic strain, and hardness reached as high as 2231 MPa, 28.2%, and 720 HV, respectively. The maximum hardness of 887 HV was obtained in the FeCrMoVTi alloy. However, the fracture strength, yield stress, and plastic strain of the alloys decreased continuously as Ti content increased. In the room-temperature compressive test, the alloys showed typical brittle fracture characteristics.     

The influence of the conditions of synthesis on the composition and mechanical properties of silicon oxycarbonitride nanocomposite films

Dielectric films of hydrogenated silicon oxycarbonitride SiC _x N _y O _z :H were prepared by plasmaenhanced chemical vapor deposition using gas mixtures of 1,1,1,3,3,3-hexamethyldisilazane (HMDS) or 1,1,3,3-tetramethyldisilazane (TMDS) with oxygen and nitrogen in the temperature range of 373–973 K. The effect of the conditions of synthesis on the chemical and phase composition of the films was studied, in the amorphous part of which nanocrystals belonging to the phases of the Si–C–N system α-Si₃N₄, α-Si_3–x C _x N₄, and graphite were distributed. To measure the hardness and Young’s modulus, the nanoindentation method was used. The influence that the synthesis temperature and nitrogen-to-oxygen ratio in the initial gas mixtures HMDS + O₂ + xN₂ and TMDS + O₂ + xN₂ have on the hardness and Young’s modulus of the resulting SiC _x N _y O _z :H films was investigated. The maximum obtained values of these parameters were 20.4 and 201.5 GPa, respectively.     

Effects of Duty Cycle on Texture Orientation and Composition of TiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Nanostructured coatings

Nanostructured titanium carbide (TiC_x) coatings are deposited on steel substrates by plasma chemical vapor deposition using three different duty cycles of 33, 40, and 50% and characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The relationship between the texture orientation/elemental concentration and duty cycle can be divided into two regimes, carbide (TiC_x) state and oxycarbide (TiC_xO_y) state. The coatings crystallize into a TiC NaCl-type crystal structure (FCC) in the carbide and oxycarbide states and a smaller “x” in the TiC_x coatings causes the transformation of the preferred orientation of (200) in the carbide state to (111) in the oxycarbide state. A poorly crystallized anatase phase is also observed from the coatings deposited using duty cycles of 40 and 50% and this anatase phase is detected from the oxycarbide state.