Magnetoresistive properties of Ni-doped La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> manganites

La_0.7Sr_0.3Mn_1?x Ni _x O₃ (x = 0, 0.025, 0.050 and 0.075) ceramics were prepared by the conventional solid-state reaction method. The partial substitution of Mn by Ni²⁺ leads to a decrease in cell volume as well as a structural transition from the rhombohedral to the orthorhombic structure. Ni²⁺ doping increases the electrical resistivity, decreases the semiconductor–metal transition temperature (T _ms) and relatively enhances the room temperature magnetoresistance (MR), especially in x = 0.025 and around T _ms. With respect to conduction mechanism, the small polaron hopping (SPH) and the variable range hopping (VRH) models were used to examine conduction in the semiconducting region.     

Floral Biosynthesis of Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanoparticles Using <Emphasis Type="Italic">Chaenomeles</Emphasis> sp. Flower Extracts for Efficient Medicinal Applications

Manganese oxide (Mn₃O₄) and iron oxide (Fe₂O₃) nanoparticles were successfully synthesized with the flower extracts of Chaenomeles sp. This is the first ever approach to synthesize nanoparticles from Chaenomeles sp. flower extracts. The organic molecules present in the flower extracts actively converted the nitrate precursor into its corresponding nanoparticles. The organic molecules that are involved in the synthesis of nanoparticles are identified using different phytochemical and gas chromatography–mass spectrometry analyses. The identified components are glycosides, alkaloids, terpenoids, saponins, flavonoids, quinines, and steroids. The structural and chemical compositions of the synthesized powder were also analyzed. The x-ray powder diffraction analysis revealed that the particles show tetragonal and rhombohedral crystalline phases. The Fourier transform infrared spectroscopy analysis showed the functional groups that are involved in the reduction of nitrates into the corresponding nanoparticles. Energy-dispersive x-ray spectroscopy analysis confirmed the presence of the elements in the synthesized nanoparticles. Transmission electron microscopy images showed the formation of spherical nanoparticles with an average size of 30–100 nm. Antioxidant analysis showed that the synthesized nanoparticles had excellent antioxidant potential. The antibacterial study showed that they inhibit the growth of harmful bacteria such as Pseudomonas aeruginosa and Streptococcus pyogenes. Thus, this study proposes a new eco-friendly and nontoxic method to synthesize nanoparticles for medicinal applications.     

Properties of the Ti<Subscript>40</Subscript>Zr<Subscript>10</Subscript>Cu<Subscript>36</Subscript>Pd<Subscript>14</Subscript> BMG Modified by Sn and Nb Additions

The results of investigation of the influence of additions of 2 and 3 at.% of Sn and simultaneously of Sn and 3 at.% Nb on microstructure and properties of the bulk metallic glasses of composition (Ti₄₀Cu_36?x Zr₁₀Pd₁₄Sn _x )_100?y Nb _y are reported. It was found that the additions of Sn increased the temperatures of glass transition (T _g), primary crystallization (T _x ), melting, and liquidus as well as supercooled liquid range (ΔT) and glass forming ability (GFA). The nanohardness and elastic modulus decreased in alloys with 2 and 3 at.% Sn additions, revealing similar values. The 3 at.% Nb addition to the Sn-containing amorphous phase decreased as well all the T _g, T _x , T _L, and T _m temperatures as ΔT and GFA; however, relatively larger values of this parameters in alloys containing larger Sn content were preserved. In difference to the previously published results, in the case of the amorphous alloys containing small Nb and Sn additions, a noticeable amount of the quenched-in crystalline phases was not confirmed, at least of the micrometric sizes. In the case of the alloys containing Sn or both Sn and Nb, two slightly different amorphous phase compositions were detected, suggesting separation in the liquid phase. Phase composition of the alloys determined after amorphous phase crystallization was similar for all compositions. The phases Cu₈Zr_3, CuTiZr, and Pd₃Zr were mainly identified in the proportions dependent on the alloy compositions.     

High-Temperature Oxidation of Nickel-Based Cermet Coatings Containing WC and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanosized Particles

This paper investigates the high-temperature oxidation of cermet coatings composed of two types of nanosized particles (WC and a mixture of WC and Al₂O₃) incorporated in nickel and produced by co-electrodeposition. For this purpose, high-temperature oxidation tests were conducted at three temperatures (500, 600, and 700 °C) in dry air with 6 time intervals up to 96 h and mass changes at each specific time interval was measured. Statistical techniques were used to calculate the oxidation rate constants (k) and growth-rate time constants (a) for all coatings. The confidence intervals associated with tests were also calculated. The results showed linear to sub-parabolic oxidation rates for coatings composed of only WC particles and sub-liner to liner oxidation rates for coating with both WC and Al₂O₃ particles. The reduction in oxidation rates for coatings with both WC and Al₂O₃ particles were correlated to the addition of Al₂O₃ particles in the matrix.     

Mechanical and Tribological Properties of HVOF-Sprayed (Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-NiCr+Ni) Composite Coating on Ductile Cast Iron

The aim of the investigations was to compare the microstructure, mechanical, and wear properties of Cr₃C₂-NiCr+Ni and Cr₃C₂-NiCr coatings deposited by HVOF technique (the high-velocity oxygen fuel spray process) on ductile cast iron. The effect of nickel particles added to the chromium carbide coating on mechanical and wear behavior in the system of Cr ₃ C ₂ -NiCr+Ni/ductile cast iron was analyzed in order to improve the lifetime of coated materials. The structure with particular emphasis of characteristic of the interface in the system of composite coating (Cr ₃ C ₂ -NiCr+Ni)/ductile cast iron was studied using the optical, scanning, and transmission electron microscopes, as well as the analysis of chemical and phase composition in microareas. Experimental results show that HVOF-sprayed Cr₃C₂-NiCr+Ni composite coating exhibits low porosity, high hardness, dense structure with large, partially molten Ni particles and very fine Cr₃C₂ and Cr₇C₃ particles embedded in NiCr alloy matrix, coming to the size of nanocrystalline. The results were discussed in reference to examination of bending strength considering cracking and delamination in the system of composite coating (Cr ₃ C ₂ -NiCr+Ni)/ductile cast iron as well as hardness and wear resistance of the coating. The composite structure of the coating provides the relatively good plasticity of the coating, which in turn has a positive effect on the adhesion of coating to the substrate and cohesion of the composite coating (Cr₃C₂-NiCr+Ni) in wear conditions.     

Acid-acid function of Eichhornia crassipes roots as inhibitor for mild steel in 0.5 M H<Subscript>2</Subscript>SO<Subscript>4</Subscript> solution

The inhibitory potential of an acid extract of Eichhornia crassipes constituents on corrosion of mild steel in 0.5 M H₂SO₄ solution was the basis of this study. Acid extract of the root was employed to create the same type of environment for acidic cleaning and pickling. The roots of Eichhornia crassipes (water hyacinth) were sun-dried and pulverized into powdered form. Acid extraction was carried out by weighing 10 g of the pulverized roots into a beaker containing 1000 mL of 0.5 M H₂SO₄, placed in water bath at 90°C for 6 h and filtered the second day. The mild steel with a known weight was immersed inside the respective concentration of the blank and inhibitors (2–10% vol/vol) solutions at room temperature, after which it was retrieved and weighed at 1-day interval progressively for 12 days. A collection of compositional data was from AAS, FTIR. Polarization resistant, current density (I _corr), and corrosion potentials (E _corr) obtained from Methro Ohms Potentiostat. Phytochemical screening of the corrosion product was carried out using Spectrophotometer. Polarization calculation shows that the root acid extracts on mild steel have corrosion resistance potentials even after preserving it for 60 days.     

Characterization of Microstructure and Wear Resistance of PEO Coatings Containing Various Microparticles on Ti6Al4V Alloy

Titania-based composite coatings were prepared by plasma electrolytic oxidation (PEO) treatment of Ti6Al4V alloy in electrolyte with α-Al₂O₃, Cr₂O₃ or h-BN microparticles in suspension. The microstructure, composition of PEO composite coatings were analyzed by SEM, EDS and XRD. The wear resistance of composite ceramic coatings was studied by ball-on-disk wear test at ambient temperature and 300 °C. The results showed that the addition of microparticles accelerated the growth rate of PEO coating and changed the microstructure and composition of PEO coating. PEO coating was porous and mainly composed of rutile-TiO₂, anatase-TiO₂ and Al₂TiO₅. PEO/α-Al₂O₃ (Cr₂O₃ or h-BN) composite coating only had small micropores and appeared some α-Al₂O₃ (Cr₂O₃ or h-BN) phase. Besides, the addition of α-Al₂O₃ (Cr₂O₃ or h-BN) microparticles greatly improved the wear resistance of PEO coating. At ambient temperature, abrasive wear dominated the wear behavior of PEO coating, but abrasive wear and adhesive peel simultaneously happened at 300 °C. Whether at ambient temperature or 300 °C, PEO composite coating had better wear resistance than PEO coating. Besides, PEO/h-BN composite coating outperformed other composite coatings regardless of the temperature.     

Influence of High Pulsed Magnetic Field on the Dislocations and Mechanical Properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al Composites

At T6 state, Al–Zn–Mg–Cu aluminum matrix composites reinforced with Al₂O₃ particles generated in situ were subjected to high pulsed magnetic fields at different magnetic induction intensities (B = 2, 3 and 4 T). The results show that the dislocation densities in the treated samples increased with increasing B, and the magnetoplastic effect was determined to be the primary cause. The effect of the magnetic field is believed to alter the spin state of free electrons between dislocations and obstacles from the singlet state (associated with high bonding energy) to the triplet state (low bonding energy). The maximum ultimate tensile strength of 532 MPa was obtained at B = 4 T with 30 pulses, which was 20.7% higher than that of the initial sample, primarily because of dislocation strengthening. At B = 2 T, the elongation was at its maximum of 9.3%, representing an increase of 12% compared with the initial sample, while the associated ultimate tensile strength (447 MPa) was still higher than that of the untreated sample (440 MPa). The relationship between mechanical properties and microstructure was analyzed, and the improved properties observed in this work are explained by the transition of the electron spin state and the piling up of dislocations.     

Effect of Hydrogen Intercalation on the Structure of YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> with a Low Oxygen Content

We used Raman spectroscopy to study the interaction of YBa₂Cu₃O_y (123) (y ≤ 6.5) with hydrogen at temperatures of 150–200°С. In contrast to the YBa₂Cu₃O_6.96 compound, compositions with low oxygen contents show a lower tendency to form stacking faults. We found that the hydrogenation of these compositions does not lead to the transformation of the 123 phase to the pseudo-124 phase. Absorbed hydrogen does not react with oxygen in 123 and does not form hydroxyl groups. The H_xYBa₂Cu₃O_y oxyhydride is the hydration-reaction product.     

Thermal Spray Deposition,Phase Stability and Mechanical Properties of La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>/LaAlO<Subscript>3</Subscript> Coatings

This paper deals with the deposition of La₂Zr₂O₇ (LZO) and LaAlO₃ (LAO) mixtures by air plasma spray (APS). The raw material for thermal spray, single phase LZO and LAO in a 70:30 mol.% ratio mixture was prepared from commercial metallic oxides by high-energy ball milling (HEBM) and high-temperature solid-state reaction. The HEBM synthesis route, followed by a spray-drying process, successfully produced spherical agglomerates with adequate size distribution and powder-flow properties for feeding an APS system. The as-sprayed coating consisted mainly of a crystalline LZO matrix and partially crystalline LAO, which resulted from the high cooling rate experienced by the molten particles as they impact the substrate. The coatings were annealed at 1100 °C to promote recrystallization of the LAO phase. The reduced elastic modulus and hardness, measured by nanoindentation, increased from 124.1 to 174.7 GPa and from 11.3 to 14.4 GPa, respectively, after the annealing treatment. These values are higher than those reported for YSZ coatings; however, the fracture toughness (K _IC) of the annealed coating was only 1.04 MPa m^0.5.     

Effect of water intercalation on the structure and electrophysical properties of YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>6.9</Subscript>

The influence of water vapors and plastic deformation on the structure and electrophysical properties of YBa₂Cu₃O_6.9 (123) has been studied. It has been established that, at T = 200°C, the introduction of water into the structure of YBa₂Cu₃O_6.9 leads to its transition into a defect tetragonal phase of the 124 type as a result of the formation of planar stacking faults. After annealing at T = 930°C, these defects are partially retained and are efficient centers of pinning in the magnetic fields applied perpendicularly to the c axis, which makes it possible to increase (by an order of magnitude) the critical current density in the high-textured ceramics at 77 K in the external magnetic field of 5–10 T. The plastic deformation of the hydrated ceramics favors the reverse transition of the arising 124 phase to the 123 phase at T = 930°C and is accompanied by a recrystallization of the material, which leads to the appearance of a texture and an increase the critical current density.     

Effect of hydrogen intercalation on the critical parameters of YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>

The effect of hydrogenation at T = 150 and 200°C on the electrophysical properties of highly textured YBa₂Cu₃O _y ceramics with different oxygen content has been investigated. Like hydration, hydrogenation results in the deterioration of these properties. However, in samples with high oxygen contents (y = 6.96) hydrogenated at T = 150°C after oxidation (400°C) or recovery annealing with subsequent oxidation, the critical current density and first critical field increase compared to the initial state. The improvement of the properties occurs mainly in a magnetic field applied perpendicularly to the c axis. As after hydration, this is connected with the formation of planar defects in the course of low-temperature annealing. In addition, in the process of the hydrogenation, the partial reduction of copper occurs with the formation of microinclusions of Cu₂O and other products of chemical decomposition, which are extra pinning centers of magnetic vortices.     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiC Composite Prepared by Spark Plasma Sintering Process: Evaluation of Mechanical and Tribological Properties

Al₂O₃-10TiC composites were synthesized by spark plasma sintering (SPS) process. Microstructural and mechanical properties of the composite reveal homogeneous distribution of the fine TiC particles in the matrix. The samples were produced with different sintering temperature, and it shows that the hardness and density gradually increases with increasing sintering temperature. Abrasion wear test result reveals that the composite sintered at 1500 °C shows high abrasion resistance (wt. loss ~ 0.016 g) and the lowest abrasion resistance was observed for the composite sample sintered at 1100 °C (wt. loss ~ 1.459 g). The profilometry surface roughness study shows that sample sintered at 1100 °C shows maximum roughness (R_a = 6.53 µm) compared to the sample sintered at 1500 °C (R_a = 0.66 µm) corroborating the abrasion wear test results.     

Activities of Fe,FeO, Fe<Subscript>2</Subscript>0<Subscript>3</Subscript>, and CaO in Simple Slags

The data previously reported for the quantity j = Fe⁺⁺⁺/(Fe⁺⁺+Fe⁺⁺⁺) as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe₂O₃, and CaO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO₂ ratios.     

Influence of Feedstock Powder Modification by Heat Treatments on the Properties of APS-Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-40% TiO<Subscript>2</Subscript> Coatings

The formation and decomposition of aluminum titanate (Al₂TiO₅, tialite) in feedstock powders and coatings of the binary Al₂O₃-TiO₂ system are so far poorly understood. A commercial fused and crushed Al₂O₃-40%TiO₂ powder was selected as the feedstock for the experimental series presented in this paper, as the composition is close to that of Al₂TiO₅. Part of that powder was heat-treated in air at 1150 and 1500 °C in order to modify the phase composition, while not influencing the particle size distribution and processability. The powders were analyzed by thermal analysis, XRD and FESEM including EDS of metallographically prepared cross sections. Only a maximum content of about 45 wt.% Al₂TiO₅ was possible to obtain with the heat treatment at 1500 °C due to inhomogeneous distribution of Al and Ti in the original powder. Coatings were prepared by plasma spraying using a TriplexPro-210 (Oerlikon Metco) with Ar-H₂ and Ar-He plasma gas mixtures at plasma power levels of 41 and 48 kW. Coatings were studied by XRD, SEM including EDS linescans of metallographically prepared cross sections, and microhardness HV1. With the exception of the powder heat-treated at 1500 °C an Al₂TiO₅-Ti₃O₅ (tialite–anosovite) solid solution Al_2?xTi_1+xO₅ instead of Al₂TiO₅ existed in the initial powder and the coatings.     

Dual-Layer Oxidation-Protective Plasma-Sprayed SiC-ZrB<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Carbon Nanotube Coating on Graphite

Graphite is used in high-temperature gas-cooled reactors because of its outstanding irradiation performance and corrosion resistance. To restrict its high-temperature (>873 K) oxidation, atmospheric-plasma-sprayed SiC-ZrB₂-Al₂O₃-carbon nanotube (CNT) dual-layer coating was deposited on graphite substrate in this work. The effect of each layer was isolated by processing each component of the coating via spark plasma sintering followed by isothermal kinetic studies. Based on isothermal analysis and the presence of high residual thermal stress in the oxide scale, degradation appeared to be more severe in composites reinforced with CNTs. To avoid the complexity of analysis of composites, the high-temperature activation energy for oxidation was calculated for the single-phase materials only, yielding values of 11.8, 20.5, 43.5, and 4.5 kJ/mol for graphite, SiC, ZrB₂, and CNT, respectively, with increased thermal stability for ZrB₂ and SiC. These results were then used to evaluate the oxidation rate for the composites analytically. This study has broad implications for wider use of dual-layer (SiC-ZrB₂/Al₂O₃) coatings for protecting graphite crucibles even at temperatures above 1073 K.     

Microstructure and Electron Energy-Loss Spectroscopy Analysis of Interface Between Cu Substrate and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Film Formed by Aerosol Deposition Method

Aerosol deposition method is a technique to form dense films by impacting solid particles on a substrate at room temperature. To clarify the bonding mechanism between AD films and substrates, TEM observation and electron energy-loss spectroscopy (EELS) analysis of the interface between Al₂O₃ AD films and Cu substrates were conducted. The Al₂O₃ film was directly adhered to the Cu substrate without any void or crack. The film was composed of randomly oriented α-Al₂O₃ crystal grains of about 10-20 nm large. At the Al₂O₃/Cu interface, the lattice fringes of the film were recognized, and no interfacial layer with nanometer-order thickness could be found. EELS spectra near O-K edge obtained at the interface had the pre-peak feature at around 528 eV. According to previously reported experiments and theoretical calculations, this suggests interactions between Cu and O in Al₂O₃ at the interface. It is inferred that not only the anchoring effect but also the ionic bonding and covalent bonding that originates from the Cu-O interactions contribute to the bonding between Al₂O₃ AD films and Cu substrates.     

Temperature Dependence of the Surface Energy of the Low Index Planes of UO<Subscript>2</Subscript> and ThO<Subscript>2</Subscript>

The temperature dependence of the surface energy γ of the low index (111), (110), and (100) planes of UO₂ and ThO₂ was calculated for the first time, using a simple method based on physical and thermodynamic quantities and considerations. The extrapolated to 0 K surface energy values agreed well with the available theoretical data reported in literature for the (111) and (110) surfaces, whereas they were significantly lower for the (100) surface. The γ ₁₀₀/γ ₁₁₁ ratio for UO₂ and ThO₂ revealed the formation of crystals with truncated octahedron structure in thermodynamic equilibrium. This structure shifts to octahedral with increasing temperature. Comparison with experimentally determined surface energies of the polycrystalline oxides showed that their values are in the range between γ ₁₁₁ and γ ₁₀₀.     

Phase Formation of the Yttrium Aluminates in the Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiC System

Phase formation sequence of the yttrium aluminates in the Y₂O₃-Al₂O₃-SiC ternary system as temperature increases were investigated via x-ray diffraction (XRD). Results showed that YAM (monoclinic), YAP (perovskite) and YAG (garnet) were the yttrium aluminates presented in the solid-state reacted samples at a fixed Al₂O₃:SiC ratio of 1:1. Formation of the yttrium aluminates depended on the temperature. The YAM, YAP and YAG started to form below 1150 °C, at 1300 °C, and at 1450 °C, respectively. Accordingly, two behavior phase diagrams of the Y₂O₃-Al₂O₃-SiC ternary system were recognized, one is in the temperature range of 1150-1300 °C and the other is in 1300-1450 °C, respectively. Thereafter, the phase equilibrium was reached in the temperature range of 1450-1700 °C. Effects of SiC on the phase formation processes in the ternary system were discussed.     

Effects of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nano-Particles on Corrosion Performance of Plasma Electrolytic Oxidation Coatings Formed on 6061 Aluminum Alloy

Corrosion resistance improvement of plasma electrolyte oxidation coatings on 6061 aluminum alloy in silicate electrolyte containing Al₂O₃ nano-particles was studied, with particular emphasis on the microstructure, coating growth, and corrosion behavior in 3.5 wt.% NaCl solution. The microstructure of coatings, their thickness, and phase composition were characterized using scanning electron microscopy and x-ray diffraction. All characterization data showed that the maximum coating thickness and lowest amount of porosity were obtained in a low concentration of KOH, a high concentration of Na₂SiO₃, and moderate concentration of Al₂O₃ nano-particles in the electrolyte. This combination describes the optimum plasma electrolytic oxidation electrolyte, which has the best conductivity and oxidizing state, as well as the highest incorporation of electrolyte components in the coating growth process. On the other hand, incorporation and co-deposition of Al₂O₃ nano-particles were more pronounced than SiO₃ ^2? ions in some level of molar concentration, which is due to the higher impact of electron discharge force on the adsorption of Al₂O₃ nano-particles. The electrochemical results showed that the best protective behavior was obtained in the sample having a coat with the lowest porosity and highest thickness.