Preparation and properties of styrene–ethylene–butylene–styrene block copolymer/clay nanocomposites: I. Effect of clay content and compatibilizer types

BACKGROUND: Polymer/clay (silicate) systems exhibit great promise for industrial applications due to their ability to display synergistically advanced properties with relatively small amounts of clay loads. The effects of various compatibilizers on styrene–ethylene–butylene–styrene block copolymer (SEBS)/clay nanocomposites with various amounts of clay using a melt mixing process are investigated. RESULTS: SEBS/clay nanocomposites were prepared via melt mixing. Two types of maleated compatibilizers, styrene–ethylene–butylene–styrene block copolymer grafted maleic anhydride (SEBS‐g‐MA) and polypropylene grafted maleic anhydride (PP‐g‐MA), were incorporated to improve the dispersion of various amounts of commercial organoclay (denoted as 20A). Experimental samples were analyzed using X‐ray diffraction and transmission electron microscopy. Thermal stability was enhanced through the addition of clay with or without compatibilizers. The dynamic mechanical properties and rheological properties indicated enhanced interaction for the compatibilized nanocomposites. In particular, the PP‐g‐MA compatibilized system conferred higher tensile strength or Young's modulus than the SEBS‐g‐MA compatibilized system, although SEBS‐g‐MA seemed to further expand the interlayer spacing of the clay compared with PP‐g‐MA. CONCLUSION: These unusual results suggest that the matrix properties and compatibilizer types are crucial factors in attaining the best mechanical property performance at a specific clay content. Copyright © 2007 Society of Chemical Industry     

PP/PA11合金的结晶性能研究

用马来酸酐接枝聚丙烯(PP-g-MA)和苯乙烯-马来酸酐无规共聚物(RSMA)作增容剂,制备了PP/PA11合金,并对合金的结晶性能进行了研究。傅立叶转换红外光谱(FTIR)表明,RSMA的增容机理与PP-g-MA不同。比较了2种增容体系的差示扫描量热(DSC)曲线,发现PP-g-MA增容体系中PP的熔融温度向更高温度移动,同时PP-g-MA的加入更能影响PP和PA11两相的结晶,使体系的结晶度增大,从而使合金的缺口冲击性能表现出更强的脆性。     

Extrusion of linear polypropylene–clay nanocomposite foams

This work presents new results on using organoclay with an appropriate polymeric compatibilizer as rheology‐modifying additives for extrusion foaming of a linear polypropylene (PP), which by itself does not display strain hardening in extensional flow of the melt. The uniaxial melt‐extensional viscosity behavior of several nanocomposites prepared with varying ratio of bound maleic anhydride to clay as well as varying compatibilizer molecular weight was investigated. A chemical‐blowing agent was used at a fixed concentration for foaming these nanocomposites in a single‐screw extruder. Among nanocomposites with similar levels of clay dispersion or intercalation, the ones that displayed significant strain hardening in the melt state along with slower crystallization led to extruded PP nanocomposite foams with smaller cell sizes and greater cell density by reducing cell coalescence. This was achieved with as little as 3 wt% organoclay and a high‐molecular weight PP‐g‐MA compatibilizer in linear PP. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Evaluation of polypropylene grafted with maleic anhydride and styrene as a compatibilizer for polypropylene/clay nanocomposites

Among modified Poly(propylene)s (PPs) grafted with polar monomers, PP grafted with maleic anhydride (PP-g-MAH) is known to be the most efficient compatibilizer for PP/clay nanocomposites, since it provides well-dispersed nanostructures and yields optimal physical properties of the nanocomposites. One drawback of this material, however, is that it becomes brittle and its viscosity decreases drastically, leading to nanocomposites with low toughness as the graft degree of MAH increases. Therefore, there is a limitation to increasing both stiffness and toughness of PP/clay nanocomposites with PP-g-MAH. In this study, we investigated the performance of a PP grafted with maleic anhydride and styrene (PP-g-MAH-St) as compatibilizers in PP/clay nanocomposites. It was found that the incorporation of styrene as a comonomer prevents molecular weight reduction of the PP main chain upon high loading of a radical initiator for high graft degree of MAH. The compatibilizers (PP-g-MAH-St) thus obtained show good compatibilizing performance in PP/clay nanocomposites. The PP/clay nanocomposites compatibilized by PP-g-MAH-St show both high stiffness and toughness, which is accomplished by using a compatibilizer of higher viscosity compared with PP-g-MAH.     

Effect of processing conditions on morphology and mechanical properties of compatibilized polypropylene nanocomposites

This work focuses on the influence of processing conditions on the nanocomposites structure, i.e. intercalated or exfoliated, and on the enhancement of mechanical properties of polypropylene (PP) nanocomposites. These nanocomposites were prepared using the melt intercalation technique in a co-rotating intermeshing twin screw extruder. In order to optimise processing conditions, both screw speed and barrel temperature profile were changed. The role of the compatibilizer (maleic anhydride grafted polypropylene) was also studied. The results obtained show that the barrel temperature is a very important parameter: using lower processing temperature, the apparent melt viscosity and, consequently, the shear stress are higher and, therefore, the exfoliation of the clay is promoted. Even using optimised processing conditions, exfoliation of clay can be achieved only when an high compatibility between polymer and clay exists: the PP nanocomposites containing maleic anhydride show an exfoliated structure and a sensible enhancement of mechanical properties while PP nanocomposites without compatibilizer show a structure mainly intercalated and a lower improvement of mechanical properties.     

Preparation and mechanical properties of PP/PP-g-MA/Org-MMT nanocomposites with different MA content

Summary Polypropylene-clay nanocomposites were prepared by melt intercalation in a twin screw extruder using two mixing methods: two-step mixing and one-step mixing. The effect of using two different kinds of PP-g-MA (polypropylene-grafted maleic anhydride), with graft efficiencies of 0.1 and 1.0 wt% of MA and with different molecular weight, on clay dispersion and mechanical properties of nanocomposites was investigated. Three different clays, natural montmorillonite (Cloisite Na+) and chemically modified clays Cloisite 20A and Cloisite 30B were used. The relative influence of each factor was observed from structural analysis by WAXD, TEM, and mechanical properties. X-ray diffractometry (XRD) was used to investigate the intercalation effect in the nanocomposites. The results indicted that the intercalation effect and mechanical properties, specially modulus, tensile strength and impact strength, were enhanced by increasing the content of MA, using maleated PP with higher graft efficiency, and using the two step mixing conditions. Better dispersion and exfoliation were obtained when using clay 20A than 30B and natural Na+ montmorillonite. The results showed that clay dispersion and interfacial adhesion are greatly affected by the kind of maleated PP. The increase in content of polar groups gives as a result better interfacial adhesion and subsequent mechanical performance.     

Preparation of polypropylene–clay nanocomposites by the co‐intercalation of modified polypropylene and short‐chain amide molecules

The effect of short‐chain amide (AM) molecules on the intercalation of montmorillonite clay has been investigated by the melt blending of polypropylene (PP) with clay in the presence of AM molecules such as 13‐cis‐docosenamide (erucamide). Polypropylene–clay nanocomposites (PPCNs) were prepared by the co‐intercalation of maleic anhydride grafted polypropylene (PP–MA) and an AM compound. The resulting nanocomposite structures were characterized with X‐ray diffraction (XRD) and transmission electron microscopy, whereas the thermal characterization of the PPCNs was conducted by thermogravimetric analysis. XRD results showed that the AM molecules intercalated into clay galleries and increased the interlayer spacing, a result confirmed by surface energy (contact angle) and melt flow index measurements. This additive allowed the formation of an intercalated nanocomposite structure, but an exfoliated PPCN structure was also formed with the use of AM with a PP–MA‐based compatibilizer. A new preparation method for PPCNs was, therefore, developed by the co‐intercalation of AM and PP–MA; this resulted in a significantly improved degree of intercalation and dispersion. The enhanced thermal stability of PPCN, relative to pure PP, further demonstrated the improved clay dispersion in the nanocomposite structures prepared by this method. A possible mechanism for the co‐intercalation of AM and PP–MA into the clay galleries is proposed, based on hydrogen bonding between these additives and the silicate layers. Consideration is also given to possible chemical reactions and physical interactions in this rather complex system. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of maleic anhydride grafted polypropylene compatibilizer on the morphology and properties of polypropylene/multiwalled carbon nanotube composite

The effect of maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer on the mechanical and electrical properties of a polypropylene‐carbon nanotube composite is presented. Commercially available grades of polypropylene homopolymer (PP) and multiwalled CNT (MCNT) were used to prepare composites (PP/MCNT) by melt compounding. The effects of maleic anhydride graft level and loading on material properties were investigated. The addition of MCNT without compatibilizer enhanced the mechanical properties of PP, whereas addition of both grades of MA‐g‐PP alone had a detrimental effect. When MA‐g‐PP was added as a compatiblizer to the PP/MCNT composite, flexural and tensile moduli increased, indicating that enhanced levels of MCNT dispersion within PP had been achieved. Strength of the nanocomposite decreased with the addition of both grades of MA‐g‐PP, possibly due to the deterioration of the mechanical properties of the polymer in the presence of lower molecular weight MA‐g‐PP. Electrical resistivity improved with both grades of MA‐g‐PP, with higher maleic anhydride graft levels having the most significant effect. Scanning electron microscopy analysis confirmed that the optimum state of dispersion was for the nanocomposite prepared with MA‐g‐PP with highest grafting level. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Morphology,Rheological Properties,and Crystallization Behavior of Polypropylene/Clay Nanocomposites

Polypropylene/clay nanocomposites (PP/I.44P, PPCNs) were prepared in a twin-screw extruder using maleic anhydride grafted polypropylene (MAPP) as a compatibilizer. The intercalation of polypropylene into nanoclay particles was studied using X-ray diffraction. Rheological properties of the nanocomposites were investigated using a rheometer. The enhanced complex viscosity at low frequency regime indicated that the melt elasticity and melt strength of the nanocomposites were improved by adding nanoclay. The non-isothermal crystallization behavior of the nanocomposites was studied using differential scanning calorimetry (DSC) at various cooling rates and was analyzed with the Avrami method. It was found that the nanoclay acted as a heterogeneous nucleating agent resulted in higher crystallization temperature and higher crystallization rate than neat PP. Polarized optical microscopy revealed that the spherulites in the nanocomposites were finer than in the neat system.     

相容剂和加工工艺对PA1010/PP共混体系形态和力学性能的影响

以马来酸酐（MAH）和苯乙烯（St）多单体熔融接枝聚丙烯[PP-g-(MAH-co-St）]为相容剂,制备了聚酰胺10101/聚丙烯（PA1010/PP）共混体系。用毛细管流变仪、扫描电子显微镜、力学性能测试等方法研究了和加工工艺相容剂对PA1010/PP共混体系的形态和力学性能的影响。结果表明,相容剂PP-g-(MAH-co-St)有效降低了PA1010/PP共混体系的熔体流动速率;该共混体系熔体属于假塑性流体,熔体黏度随PP-g-(MAH-co-St)含量的增加逐渐增大;随着相容剂含量的增加,PA1010/PP共混体系中分散相PP的粒径逐步减小,力学性能得到改善,PA1010/PP/PP-g-(MAH-co-St)为70/25/5和70/20/10的共混体系的拉伸强度分别比PA1010/PP (70/30)共混体系提高了55.0 %和61.9 %,冲击强度分别提高了61.0 %和129.7 %;剪切速率为706.5 s-1时出现熔体破裂现象,剪切速率为5002.65 s-1时出现严重熔体破裂。     

Experimental and computational investigation of EVOH/clay nanocomposites

Ethylene–vinyl alcohol copolymer (EVOH)/organoclay nanocomposites were prepared via a dynamic melt‐intercalation process. The effect of compatibilizers on the melt blending torque, intercalation level, and morphology of EVOH/organoclay systems was investigated. Maleic anhydride grafted ethylene vinyl acetate (EVA‐g‐ MA), or maleic anhydride grafted linear low‐density polyethylene (LLDPE‐g‐MA), were used to compatibilize EVOH with clay, at various concentrations (1, 5, and 10 wt %). Computer‐simulation techniques are used to predict structural properties and interactions of EVOH with compatibilizers in the presence and absence of clay. The simulation results strongly support the experimental findings and their interpretation. X‐ray diffraction shows enhanced intercalation within the galleries when the compatibilizers were added. Interestingly, results were obtained for the EVOH/clay/compatibilizer systems, owing to a high level of interaction developed in these systems. Thermal analysis shows that, upon increasing the compatibilizer content, lower crystallinity levels result, until at a certain compatibilizer content no crystallization is taking place. Significantly higher mixing viscosity levels were obtained for the EVOH/organoclay blends compared with the neat EVOH polymer. The storage modulus was higher compared with the uncompatibilized EVOH/organoclay blend in the presence of EVA‐g‐MA compatibilizer (at all concentrations), and only at low contents of LLDPE‐g‐MA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2060–2066, 2005     

Effects of different compatibilizers on the rheological,thermomechanical, and morphological properties of HDPE/LLDPE blend‐based nanocomposites

The influence of two different compatibilizers and their combination (maleic anhydride grafted high density polyethylene, HDPE‐g‐MA; maleic anhydride grafted linear low density polyethylene, LLDPE‐g‐MA; and 50/50 wt % mixture of these compatibilizers) on the rheological, thermomechanical, and morphological properties of HDPE/LLDPE/organoclay blend‐based nanocomposites was evaluated. Nanocomposites were obtained by melt‐intercalation in a torque rheometer in two steps. Masterbatches (compatibilizer/nanoclay 2:1) were obtained and subsequently diluted in the HDPE/LLDPE matrix producing nanocomposites with 2.5 wt % of nanoclay. Wide angle X‐ray diffraction (WAXD), steady‐state rheological properties, and transmission electron microscopy (TEM) were used to determine the influence of different compatibilizer systems on intercalation and/or exfoliation process which occurs preferentially in the amorphous phase, and thermomechanical properties. The LLDPE‐g‐MA with a high melt index (and consequently low viscosity and crystallinity) was an effective compatibilizer for this system. Furthermore, the compatibilized nanocomposites with LLDPE‐g‐MA or mixture of HDPE‐g‐MA and LLDPE‐g‐MA exhibited better nanoclay's dispersion and distribution with stronger interactions between the matrix and the nanoclay. These results indicated that the addition of maleic anhydride grafted polyethylene facilitates both, the exfoliation and/or intercalation of the clays and its adhesion to HDPE/LLDPE blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1726–1735, 2013     

多单体接枝聚丙烯对PP/PA6共混物形态及力学性能的影响

用同向双螺杆挤出机制备了马来酸酐(MAH)、苯乙烯(St)多单体熔融接枝聚丙烯[PP-g-(St-MAH)],将其作为增容剂在Haake转矩流变仪上与PP/PA6共混得到PP/PA6/PP-g-(St-MAH)共混物,并对共混物的性能及结构进行了表征。结果表明,该增容剂明显改善了共混物的力学性能,当增容剂含量为15~20份时,共混物的冲击强度和拉伸屈服强度达最大值。采用扫描电子显微镜观察共混物试样断面的形态,发现分散相的粒径明显减小,且分散均匀。     

Morphology and mechanical properties of polypropylene/organoclay nanocomposites

Polypropylene (PP) nanocomposites were prepared by melt intercalation in an intermeshing corotating twin‐screw extruder. The effect of molecular weight of PP‐MA (maleic anhydride‐ modified polypropylene) on clay dispersion and mechanical properties of nanocomposites was investigated. After injection molding, the tensile properties and impact strength were measured. The best overall mechanical properties were found for composites containing PP‐MA having the highest molecular weight. The basal spacing of clay in the composites was measured by X‐ray diffraction (XRD). Nanoscale morphology of the samples was observed by transmission electron microscopy (TEM). The crystallization kinetics was measured by differential scanning calorimetry (DSC) and optical microscopy at a fixed crystallization temperature. Increasing the clay content in PP‐ MA330k/clay, a well‐dispersed two‐component system, caused the impact strength to decrease while the crystallization kinetics and the spherulite size remained almost the same. On the other hand, PP/PP‐MA330k/clay, an intercalated three‐component system containing some dispersed clay as well as the clay tactoids, showed a much smaller size of spherulites and a slight increase in impact strength with increasing the clay content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1562–1570, 2002     

Effect of Ionomeric Compatibilizer on Clay Dispersion in Polyethylene/Clay Nanocomposites

Summary: Linear low‐density polyethylene (LLDPE)/clay nanocomposites are obtained and studied by using a zinc‐neutralized carboxylate ionomer as a compatibilizer. LLDPE‐g‐MA is used as a reference compatibilizer. Two different clays, natural montmorillonite (Closite Na⁺) and a chemically modified clay Closite 20A have been used. Nanocomposites are prepared by melt blending in a twin‐screw extruder using two mixing methods: two‐step mixing and one‐step mixing. The relative influence of each compatibilizer is determined by wide‐angle X‐ray diffraction structural analysis and mechanical properties. The results are analyzed in terms of the effect of the compatibilizing agent and incorporation method in the clay dispersion, and the mechanical properties of the nanocomposites. Experimental results confirm that the film samples with ionomer show a good mechanical performance only slightly below that of the samples with maleic anhydride (MA). The two‐step mixing conditions result in better dispersion and intercalation for the nanofillers than one‐step mixing. The exfoliation of clay platelets leads to an improved thermal stability of the composite. The oxygen permeability of the clay nanocomposites, using ionomer as a compatibilizer, is decreased by the addition of the clay.

TEM image of a PE/4 wt.‐% Closite 20A nanocomposite formed using ionomer.     

Morphology,deformation behavior and thermomechanical properties of polypropylene/maleic anhydride grafted polypropylene/layered silicate nanocomposites

Nanocomposites polypropylene (PP) with 3 and 7 wt % of clay were prepared by melt mixing. Four types of maleic anhydride grafted PP (MAPP) in broad range of MA groups content (0.3–4 wt %) and molecular weights (MW) were used as polar compatibilizers. The effect of the MAPP kind on both the clay dispersion and miscibility with PP was studied. The mixed intercalated/exfoliated morphologies of nanocomposites in the presence of all studied compatibilizers were revealed by XRD and TEM. The oligomer compatibilizer with 4 wt % of MA groups increases the intercalation ability of polymer into clay galleries but this one has limited miscibility with PP and worsens crystalline structure of polymer matrix. The MAPPs with 0.3–1.3% of MA are characterized by the lower intercalation ability but well cocrystallize with PP. Maximum reinforcing effect is attained using high MW MAPP with 0.6% MA and for nanocomposite with 7 wt % (3.8 vol %) of clay it averages almost 1.7 times relative to neat PP and 1.3 times relative to noncompatibilized composite. Dynamic storage moduli of nanocomposites compatibilized by MAPPs with 0.3–1.3% of MA containing 7 wt % of clay increase up to 1.4–1.5 around 30–75°C and over the whole temperature range remain higher compared with both neat PP and uncompatibilized composite. On the contrary, the oligomer MAPP with 4 wt % of MA groups decreases the thermal–mechanical stability of nanocomposite at high temperature compared with both PP and uncompatibilized composites. The study of nanocomposites flammability showed that creating complex composites containing both layered silicate and relatively small amount of magnesium hydroxide can be a successful approach to reduce the combustibility of PP‐based nanocomposites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Melt processing and characterization of polypropylene/pristine montmorillonite nanocomposite: Influence of compatibilizer and hyperbranched polymer

In the present investigation, nanocomposites of polypropylene (PP)‐montmorillonite (MMT) clay were prepared by a single‐step compounding method to study the influence of hyperbranched polyester (HBPE) on rheological and mechanical properties of PP composites in the presence of a compatibilizer. In service of this objective, polyvinylchloride‐grafted‐maleic anhydride (PP‐g‐MA) was used as a compatibilizer for hydrophobic PP and hydrophilic clay. Rheological property in terms of melt viscosity was examined by a Brabender torque rheometer. The composite's morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), whereas the dispersion state of nanoparticles in the PP matrix was studied by X‐ray diffraction (XRD). The thermal behavior of nanocomposites was examined by differential scanning calorimetry (DSC). The analysis of results confirmed that the interactions among both additives significantly influenced the morphology, rheology, and thermomechanical properties of the nanocomposites. J. VINYL ADDIT. TECHNOL., 22:72–79, 2016. © 2014 Society of Plastics Engineers     

Polypropylene/clay nanocomposites: An innovative one‐pot process

This work discloses a novel one‐pot preparation method of polypropylene (PP)/clay nanocomposites with high degree of clay delamination and improved thermal, mechanical and rheological properties. The in situ simultaneous synthesis of carboxylate clay from native clay and ionomer of PP‐graft maleic anhydride (PP‐g‐MA) through trihydrate sodium acetate addition, combined with water injection in the extrusion process, appears to be a valuable alternative to the use of organoclay for producing PP/PP‐g‐MA/clay nanocomposites. The influence of PP‐g‐MA graft content, and of its ionomer form, onto the clay dispersion has been especially investigated. PP‐g‐MA of low graft content is compared to a home‐made highly grafted PP‐g‐MA synthesized in the presence of N‐bromosuccinimide (NBS). The nanocomposites prepared by combining the use of NBS‐mediated PP‐g‐MA, trihydrate sodium acetate and water injection exhibit the highest clay dispersion. Thermal, rheological, and mechanical properties of the nanocomposites have been measured. POLYM. COMPOS., 36:644–650, 2015. © 2014 Society of Plastics Engineers     

Combination of double‐modified clay and polypropylene‐graft‐maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

Double‐modified montmorillonite (MMT) was first prepared by covalent modification of MMT with 3‐aminopropyltriethoxysilane and then intercalation modification by tributyl tetradecyl phosphonium ions. The obtained double‐modified MMT was melt compounded with polypropylene (PP) to obtain nanocomposites. The dispersion of the double‐modified MMT in PP was found to be greatly improved by the addition of PP‐graft‐maleic anhydride (PP‐g‐MA) as a “compatibilizer,” whose anhydride groups can react with the amino groups on the surface of the double‐modified MMT platelets and thus improve the dispersion of MMT in PP. Fourier transform infrared, X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, scanning electron microscopy, and tensile test were used to characterize the structure of the double‐modified MMT, morphology, and the thermal and mechanical properties of the nanocomposites. The results show that PP‐g‐MA promotes the formation of exfoliated/intercalated morphology and obviously increases the thermal properties, tensile strength, and Young's modulus of the PP/double‐modified MMT nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of nanoclay‐filled polyurethane/polypropylene blends

Ester‐based thermoplastic polyurethane (TPU) nanocomposites were prepared by melt blending at 190°C, using 3 wt% Cloisite 10A (organically modified montmorillonite clay) as the nanoscale reinforcement [TPU(C10A)]. The nanocomposites were subsequently melt‐blended with polypropylene (PP) using maleic anhydride–grafted polypropylene (MA‐g‐PP) as a compatibilizer [in the ratio of 70/30‐TPU/PP, 70/25/5‐TPU/PP/MA‐g‐PP, 70/25/5‐TPU (C10A)/PP/MA‐g‐PP]. Besides giving substantial increase in modulus, tensile strength, and other properties, organoclay reinforcement functions as a surface modifier for TPU hard segment resulting in improved dispersion. The morphology and other characteristics of the nanocomposite blends were investigated in terms of X‐ray diffraction, fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, tensile properties, scanning electron microscopy, and atomic force microscopy. The results indicate that the ester‐TPU(C10A)/PP/MA‐g‐PP exhibited better dispersion than other blend systems; abrasion resistance and water absorption resistance were also better for this system. POLYM. ENG. SCI., 50:1878–1886, 2010. © 2010 Society of Plastics Engineers