Flexible solar cells based on PCBM/P3HT heterojunction

[6,6]-phenyl-C61-butyric acid methyl ester (PCBM) / poly (3-hexylthiophene) (P3HT) heterojunction has not only the absorption in ultraviolet light for PCBM,but also the absorption in visible light for P3HT, which widens the incident light harvest range, improving the photoelectrical response of hybrid solar cell effectively.Using conducting polymers blend heterojunetion consisting of C60 derivatives PCBM and P3HT as charge carrier transferring medium to replace I3-/I- redox electrolyte and dye, a novel flexible solar cell was fabricated in this study.The influence of PCBM/P3HT mass ratio on the photovoltaic performance of the solar cell was also studied.flexible solar cell achieved a light-to-electric energy conversion efficiency of 1.04%, an open circuit voltage fill factor (FF) of 0.46.     

Performance improvement mechanisms of P3HT:PCBM inverted polymer solar cells using extra PCBM and extra P3HT interfacial layers

A novel P3HT:PCBM inverted polymer solar cell (IPSC) was fabricated and investigated. An extra PCBM and an extra P3HT interfacial layers were inserted into the bottom side and the top side of the P3HT:PCBM absorption layer of the IPSCs to respectively enhance electron transport and hole transport to the corresponding electrodes. According to the surface energy, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) measurement results, the extra PCBM interfacial layer could let more P3HT to form on the top side of the P3HT:PCBM blends. It revealed that the non-continuous pathways of P3HT in the P3HT:PCBM absorption layer could be reduced. Consequently, the carrier recombination centers were reduced in the absorption layer of IPSCs. The power conversion efficiency (PCE) of the P3HT:PCBM IPSCs with an extra PCBM interfacial layer greatly increased from 3.39% to 4.50% in comparison to the P3HT:PCBM IPSCs without an extra PCBM interfacial layer. Moreover, the performance of the P3HT:PCBM IPSCs with an extra PCBM interfacial layer could be improved by inserting an extra P3HT interfacial layer between the absorption layer and the MoO₃ layer. The PCE of the resulting IPSCs increased from 4.50% to 4.97%.     

Synergism of molecular weight,crystallization and morphology of poly(3-butylthiophene) for photovoltaic applications

A serial of poly(3-butylthiophene) (P3BTs) with molecular weights (MWs) ranged from 7 kDa to 50 kDa is synthesized and characterized. The DSC studies show that the thermal property and crystallinity of P3BT increase with MWs within the range from 7 kDa to 25 kDa, then decrease with further higher MW. The characteristic morphologies of incontinuous crystalline nanofibrils, interconnected nanofibrillar networks, and relative large clusters associate to low, medium and high MW P3BTs, respectively, demonstrate the strong correlation between MW, crystallinity and morphology of P3BT. It is found that the P3BT could be re-considered as the promising candidate for applications in organic optoelectronics if synergism of the crystallinity and morphology could be precisely controlled via tuning molecular weight. The polymer solar cells (PSCs) device based on P3BT with medium MW achieves an attractive power conversion efficiency of 3.5%, which is, to the best of our knowledge, the record for P3BT/PC₆₁BM PSCs and comparable to the well-studied P3HT devices.     

胆甾液晶应用于P3HT∶PCBM聚合物光伏器件研究

本研究利用液晶材料的自组装特性,将胆甾醇油酸酯3β-Hydroxy-5-cholestene 3-oleate掺杂有机聚合物太阳能电池活性层P3HT:PC61BM内,制备出不同掺杂比例的光伏器件。实验结果表明,液晶掺杂质量比为0.3%时,器件的光电转换效率最高。说明液晶分子可诱导活性层材料分子在结晶过程中有序排列,减少层内分子团簇,减少活性层薄膜缺陷,形成有效的载流子传输通道。适当的掺杂比例,增大了器件并联电阻和填充因子,器件性能得到改善。     

Phase separation-driven stratification in conventional and inverted P3HT:PCBM organic solar cells

We have used neutron reflectivity to investigate the stratification of poly(3-hexylthiophene) (P3HT) and phenyl-C₆₁-butyric acid methyl ester (PCBM) blend films. Films were spun-cast on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and titanium oxide (TiOx) layers to mimic the procedures followed for the fabrication of conventional and inverted organic photovoltaics respectively. The resultant scattering length density profiles reveal a PCBM-rich layer is formed in the vicinity of PEDOT:PSS or TiOx, while PCBM is depleted at the free surface of the film. PCBM segregation close to the substrate is further enhanced by annealing. This stratification is considered to be favorable only for inverted devices.     

Modular construction of P3HT/PCBM planar-heterojunction solar cells by lamination allows elucidation of processing–structure–function relationships

Contrary to polymer solar cells with bulk-heterojunction active layers, devices with planar-heterojunction active layers allow the decoupling of active layer phase separation from constituent crystallization, and their relative influence on device performance. We fabricated planar-heterojunction devices by first processing the electron donor and electron acceptor in isolation; they were subsequently laminated across the donor–acceptor interface to establish electrical contact. Thermal annealing was intentionally avoided after lamination to maintain the pristine charge transfer interface. Lamination thus obviates the need for solvent orthogonality; more importantly, it provides independent process tuning of individual organic semiconductor layers, ultimately allowing control over constituent structural development. We found the short-circuit current density of planar-heterojunction solar cells comprising poly(3-hexyl thiophene), P3HT, and [6,6]-phenyl-C₆₁-butyric acid methyl ester, PCBM, as the electron donor and acceptor, respectively, to be generally independent of the annealing history of P3HT. On the contrary, thermal annealing PCBM prior to lamination mainly led to a reduction in short-circuit current density. This deterioration is correlated with the development of preferentially oriented PCBM crystals that hinders electron transport in the vertical direction.     

Controlling the morphology of nanofiber-P3HT:PCBM blends for organic bulk heterojunction solar cells

Within the field of organic bulk heterojunction solar cells, the morphology of the active layer has a key role in obtaining high power conversion efficiencies. P3HT nanofibers, obtained in highly concentrated solutions, are able to give controlled morphologies directly upon deposition. Since the solar cell efficiency of fiber solar cells depends on the fiber content of the casting solution, it is important to control this parameter. Here, we demonstrate an easy way to control the fiber content in the casting solution, i.e. changing the solution temperature. By using solution heating, the overall molecular weight of the polymer in the blend is kept constant, fiber isolation is not needed and the use of solvent mixtures is avoided. The obtained optimal power conversion efficiency is shown to be linked to the morphology of the active layer, which is studied with Transmission Electron Microscopy (TEM).     

Stabilization of poly(3-hexylthiophene)/PCBM morphology by hydroxyl group end-functionalized P3HT and its application to polymer solar cells

A new concept to stabilize the morphology of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) blend through H-bond formation by using a hydroxyl group end-functionalized P3HT (HOC-P3HT-COH) as a compatibilizer is presented. Domain size of the PCBM crystals in the annealed P3HT/PCBM film is diminished with addition of HOC-P3HT-COH. Surface roughness of the P3HT/PCBM film also becomes smoother with addition of HOC-P3HT-COH. Thermal stability of solar cell device is improved significantly through the H-bond formation between HOC-P3HT-COH and PCBM. A high performance and thermal stable polymer solar cell with 4.06% power conversion efficiency under AM1.5G irradiation is fabricated with 5% HOC-P3HT-COH in P3HT/PCBM layer.     

Effect of fullerene doping on the electrical properties of P3HT/PCBM layers

Poly (3-hexylthiophene-2, 5-diyl) (P3HT) and its blend with Phenyl-C₆₁-Butyric acid-Methyl-Ester (PCBM) and fullerene (C₆₀) thin films were prepared and their electrical properties for memory applications were studied. Due to doping, a sharp decrease in the resistance for a P3HT:PCBM:C₆₀ device was observed at around 70 °C which makes it useful for thermal switching applications. Addition of C₆₀ to P3HT:PCBM blend gave a high value for R_RESET/R_SET in thermal switching. For bias switching, threshold voltage reduces to 1.4 V from 25 V with the addition of C₆₀ to P3HT layer.     

A review of recent plasmonic nanoparticles incorporated P3HT: PCBM organic thin film solar cells

An optimum thickness of organic active layer of 100 nm or possibly less results in poor optical absorption in organic photovoltaic cells (OPV). The optical absorption can be improved by using a thick organic active layer, but the charge carrier collection efficiency will decrease due to low charge carrier mobility for most of the polymeric organic semiconductor. This phenomenon imposes a trade-off between optical absorption and charge carriers transport inside OPV. Recently, metallic nanostructures such as gold (Au) and silver (Ag) with various sizes and morphologies have been identified as an alternative route to boost the performance of OPV at this specific limited thickness (ie. ≤100 nm). Multiple plasmonic effects such as optical and electrical effects are induced upon introducing metallic nanoparticle(s), NP(s) into OPV. This review highlights recent progress in plasmonic-enhanced poly(3-hexylthiophene-2,5-diyl): phenyl-C61-butyric acid methyl ester (P3HT: PCBM)-based OPV with NP(s) located either inside organic active layer or carrier transport layer (CTL) or at various interfaces within the OPV cell architecture. With understanding of the physical plasmonic effects for Au and Ag in OPV, such plasmonic NP(s) act as a new class of strategy for performance optimization.     

Impact of molecular weight on charge carrier dissociation in solar cells from a polyfluorene derivative

The effect of the molecular weight of poly[9,9-didecanefluorene-alt-(bis-thienylene) benzothiadiazole] (PF10TBT) on the photovoltaic performance of fullerene-based bulk heterojunction solar cells is investigated. An increase in molecular weight of two orders of magnitude results in a 30% increase of the short-circuit current and a rise of the fill factor from 0.45 to 0.63. Electron and hole transport are found to be virtually unaffected by changing molecular weight, which means that space-charge effects do not play a role in low molecular weight devices. Using optical modeling and numerical device simulations, we demonstrate that at low molecular weight the efficiency is mainly limited by a short lifetime of bound electron–hole pairs. This short lifetime prohibits efficient dissociation and is attributed to a deficiency in phase separation for low molecular weights.     

Incorporation of SiO2 dielectric nanoparticles for performance enhancement in P3HT:PCBM inverted organic solar cells

It is well known that organic solar cells (OSCs) with inverted geometry have not only demonstrated a better stability and longer device life time but also have shown improved power conversion efficiency (PCE). Recent studies exhibit that incorporation of metal and/or semiconducting nanoparticles (NPs) can further increase the PCE for OSCs. In this present work, we have synthesized SiO₂ NPs of various sizes (25, 50, 75 and 100 nm) using the modified Stober method and incorporated them into P3HT:PCBM photoactive layer and ZnO based electron transport layer (ETL) in order to investigate the light trapping effects in an OSC. Absorption studies have shown a considerable increase in photo absorption in both cases. The fabricated devices demonstrated 13% increase in the PCE when SiO₂ NPs are incorporated in P3HT:PCBM photoactive layer, whereas PCE was increased by 20% when SiO₂ NPs are incorporated in ZnO based ETL. Mott–Schottky analysis and impedance spectroscopy measurements have been carried out to determine the depletion width and global mobility for both the devices. The possible reason for PCE enhancement and the role of SiO₂ NPs in active layer and ZnO ETL are explained on the basis of the results obtained from Mott–Schottky analysis and impedance spectroscopy measurements.     

Influence of aluminium electrode preparation on PCE values of polymeric solar cells based on P3HT and PCBM

The main goal of the paper was investigation of influence of aluminum electrode preparation via thermal evaporation (TE) and the magnetron sputtering (MS) on power conversion efficiency (PCE) of polymeric solar cells. The photovoltaic properties of such three kinds devices based on poly(3-hexylthiophene-2,5-diyl) (P3HT) as ITO/P3HT/Al, ITO/P3HT:PCBM (1:1, w/w)/Al and ITO/PEDOT:PSS/P3HT:PCBM (1:1, w/w)/Al were investigated. For the constructed devices impedance spectroscopy were analyzed. For devices lack of PEDOT:PSS layer or lack of PCBM, photovoltaic parameters were very low and similar to the parameters obtained for device with Al electrode prepared by magnetron sputtering. The devices comprising PEDOT:PSS with P3HT:PCBM showed the best photovoltaic parameters such as a V_OC of 0.60 V, J_SC of 4.61 mA/cm², FF of 0.21, and PCE of 5.7 × 10^?1%.     

On the stability of the electrical and photoelectrical properties of P3HT and P3HT:PCBM blends thin films

New photoelectrical properties of poly(3-hexylthiophene-2,5-diyl), highly regioregular (P3HT): Methanofullerene Phenyl-C₆₁-Butyric-Acid-Methyl-Ester [60] PCBM films were putted in evidence. For the first time the electrical conductivity dependencies on temperature in dark and under different illuminations were studied for the P3HT and P3HT:PCBM blend films. These dependencies shows reversible processes and a high sensitivity of the P3HT and P3HT:PCBM to light. The decrease of the resistivity at the exposure to light is of 18% for P3HT films and of 20% for P3HT:PCBM blend films, for a irradiation under 0.5 W/m² white light at room temperature. By adding the fullerene molecules, in the 1:0.8 polymer:fullerene ratio, the electrical resistivity at room temperature of the blend films decrease compared to the polymer film by 40% in dark, and by 68% under 250 W/m² white light irradiance.The decrease of the resistivity with the temperature is more pronounced in the presence of light indicating a photon activated process.The existence of the open circuit voltage was evidenced even for planar geometry photodiodes and the values of the open circuit voltage under 1000 W/m² solar light illumination are coherent with the difference between the work functions of the electrodes.     

Correlation between polymer molecular weight and optimal fullerene content in efficient polymer solar cells

In this contribution, a donor-acceptor (D-A) copolymer PTP8, consisting of alternating benzodithiophene and thienopyrroledione with conjugated side-chains on both donor and acceptor units, was sucessfully prepared. We further investigated the effect of polymer molecular weight on polymer physicochemical properties, solar cell device performance, polymer-PCBM blend morphology, and, most importantly, polymer/PCBM blend ratio. We found that increasing the molecular weight of the donor polymer can both effectively improve the device performance and simultaneously stabilize solar cell efficiency over a wide range of polymer/PCBM blend ratios (from 1:0.5 to 1:1.0), which may lead to more thermally stable and cost-effective devices. Through intensive morphological investigation, we propose a sound morphological evolution for PTP8/PCBM blends with different molecular weights at low fullerene content.     

Influence of P3HT:PCBM blend preparation on the active layer morphology and cell degradation

Polymeric solar cells have attracted much attention during the last years due to their lower fabrication cost and possibility of using flexible substrates. However, their efficiency is usually less than 5%. Among factors affecting polymeric solar cells efficiency, the active layer morphology related to blend preparation and annealing, is one of the most important. In this work we analyze the behavior of solar cells based on poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester, P3HT:PCBM blends prepared under different conditions. Basic parameters are extracted from measured characteristics in dark and under illumination, while modeling is used to understand the mechanisms involved in the device behavior and during its degradation in ambient conditions, which are associated to the active layer characteristics.     

Effects of incorporation of copper sulfide nanocrystals on the performance of P3HT: PCBM based inverted solar cells

It has been reported that performance of bulk heterojunction organic solar cells can be improved by incorporation of an additive like metal and semiconducting nanoparticles in the active layer. Here in, we have synthesized Cu₂S nanocrystals (NCs) by chemical route and studied its dispersion in poly (3-hexylthiophene) [6, 6]-phenyl C61-butyric acid methyl ester (P3HT: PCBM) matrix. Variation in the performance parameters with change in the concentration of Cu₂S NCs into the P3HT: PCBM matrix has also been studied and it was found that the inverted geometry device with concentration of 20 wt% of Cu₂S NCs and having the structure ITO/ZnO (NPs)/P3HT: PCBM:Cu₂S NCs/MoO₃/Al has shown maximum efficiency of 3.39% which is more than 100% increase in comparison with devices without Cu₂S NCs. Photoluminescence measurements studies unveiled that the incorporation of Cu₂S NCs into a P3HT: PCBM matrix has helped in quenching photoluminescence which suggests more effective exciton dissociation at the interfaces between the P3HT and PCBM domains. The Nyquist plots obtained from impedance spectroscopy at 1 V bias in the dark has suggested the effective lifetime and global mobilities for P3HT: PCBM as 0.267 ms and 1.17 × 10⁻³ cm²/V-S and for P3HT: PCBM:Cu₂S NCs (20 wt%) systems as 0.156 ms and 2.02 × 10⁻³ cm²/V-S respectively. Based on observed photoluminescence quenching, calculated effective lifetime and global mobility, we have tried to explain the possible reason for improvement in the efficiency with the very well dispersion of Cu₂S NCs into the P3HT: PCBM matrix.     

Hybrid photovoltaic structures based on amorphous silicon and P3HT:PCBM/PEDOT:PSS polymer semiconductors

Hybrid thin film photovoltaic structures, based on hydrogenated silicon (Si:H), organic poly(3-hexythiophene):methano-fullerenephenyl-C61-butyric-acid-methyl-ester (P3HT:PCBM) and poly(3,4ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) films, have been fabricated. Organic semiconductor thin films were deposited by spin-coating technique and were exposed to radio frequency plasma enhanced chemical vapor deposition (RF PECVD) of Si:H films at deposition temperature T_d = 160 °C. Different types of structures have been investigated: H1) ITO/(p)SiC:H /P3HT:PCBM/(n) Si:H, H2) ITO/PEDOT:PSS/(i)Si:H/(n) Si:H and H3) ITO/PEDOT:PSS/P3HT:PCBM/(i)Si:H/(n)Si:H. Short circuit current density spectral response and current-voltage characteristics were measured for diagnostic of the photovoltaic performance. The current density spectral dependence of hybrid structures which contains organic layers showed improved response (50–80%) in high photon energy range (hν ≈ 3.1–3.5 eV) in comparison with Si:H reference structure. An adjustment in the absorbing layer thickness and in the contact material for ITO/PEDOT:PSS/(i)Si:H/(n)Si:H structure, resulted in a remarkably high short circuit current density (as large as 17.74 mA/cm²), an open circuit voltage of 640 mV and an efficiency of 3.75%.     

Sputtered ZnO seed layer enhances photovoltaic behavior in hybrid ZnO/P3HT solar cells

We investigated the characteristics of inverted solar cells comprising bulk-heterojunction active layers of ZnO nanowire arrays and poly(3-hexylthiophene), P3HT. By utilizing a sputtered ZnO seed layer, we are able to grow vertically oriented ZnO nanowire arrays homoepitaxially. Unlike the ZnO nanowires that are grown on sol–gel derived seed layers, our nanowires are more uniform in their dimensions and spatial distribution. This sputtered seed layer also acts as the hole-blocking layer when these nanowire arrays are incorporated in solar cells; hybrid solar cells comprising these nanowires and P3HT exhibit power conversion efficiencies of 1.6%. To date, this is the highest efficiency observed for ZnO nanowire arrays:P3HT hybrid solar cells.     

A thermodynamic and kinetic description of PCBM phase segregation and aggregation in P3HT:PCBM blends

The kinetics and thermodynamics of PCBM phase segregation and aggregation in P3HT:PCBM blends has been studied. We develop a thermodynamic model for PCBM phase segregation in P3HT:PCBM blends which explains the formation of nanoscale crystallites which subsequently diffuse and coalesce into larger PCBM aggregates. We show that the formation of nanoscale crystallites during the film making process prevents spinodal decomposition of the P3HT:PCBM blends even at PCBM weight fractions above the spinodal decomposition boundary for the system. Finally, we demonstrate that the observed aggregate morphology can be understood in terms of a kinetic model based on the diffusional flux lines of PCBM crystallite which, in turn, govern the evolution of the macroscopic growth front.