Preparation and properties of polyrotaxane from α-cyclodextrin and poly(ethylene glycol) with poly(vinyl alcohol)

α–Cyclodextrin (α-CD) was found to form inclusion complexes with poly(ethylene glycol) (PEG) having a crystalline state in high yields, which have been investigated extensively in the past. Formation of an inclusion complex depends strongly on structure, molecular weight and geometry of the polymer. Development of a dicomponent inclusion complex (DIC) of PEG and α-CD in the presence of poly(vinyl alcohol) (PVA) and initiation of hexagonal crystals upon sonication have exhibited various microstructures. Formation of the new inclusion complex in PVA heavily depends on the concentration of PVA, temperature and sonication time. The complexes produced are characterized by FTIR, HNMR spectra and powder X-ray. ¹HNMR of the complexes demonstrate that their stoichiometric ratio is 2:1 (two ethylene glycol units and one α-CD). X-ray patterns of PEG–α-CD complex indicate that the α-CD forms channels whereas PEG/α-CD/PVA creates cage-type structures.     

Synthesis of poly(ethylene glycol) functionalized MWNTs and their inclusion complexes with α-cyclodextrin

Poly(ethylene glycol) (PEG) functionalized multiwalled carbon nanotubes (MWNTs), prepared by coupling of isocyanate-decorated MWNTs with PEG of different molecular weights (M _n = 400, 1000, 2000, and 4000 g/mol), were used to form inclusion complexes (ICs) with α-cyclodextrin (α-CD) through the grafted PEG chains being threaded with α-CD rings in aqueous solution. The FTIR, TGA, UV-Vis, and scanning electron microscopy (SEM) techniques were employed to characterize the formed ICs. The ICs formation time was monitored by UV-Vis spectroscopy, and the results indicated that the inclusion interaction between MWNT surface anchored PEG chains and α-CD was dependent on the molecular weight of PEG. The grafted PEG with molecular weights of 4000 and 2000 g/mol, respectively, can form ICs with α-CD, while the grafted PEG with molecular weights of 1000 and 400 g/mol, respectively, are difficult to form ICs with α-CD due to the steric hindrance from nanotubes. The stoichiometry value determined by TGA indicated that the ratio of ethylene glycol (EG) unit to α-CD in the resulted ICs was about 15:1. In addition, the morphology of the ICs was observed by SEM and transmission electron microscopy (TEM).     

Drug absorption and release properties of crosslinked hydrogels based on diepoxy-terminated poly(ethylene glycol)s and aliphatic polyamines — a study on the effect of the gel molecular structure

Crosslinked hydrogels with well-defined chemical structures and characteristics were prepared through the reaction between diepoxy-terminated poly(ethylene glycol)s of various molecular weights and aliphatic polyamines of different hydrocarbon chain length and functionalities, and the influence of some network parameters (molecular weight between crosslinking points, crosslinking degree, hydrophobic character) upon the absorption and release of drugs of different capacity to interact with the polymer chains was comparatively investigated. Diclofenac sodium (DCFNa) and 5-fluorouracil (5FU) were used as model drugs, based on their dissimilar hydrophobic character and ability of DCFNa to form crown ether-like complexes with PEG chains through the sodium cation. The experiments showed that the most important interactions occurring in these systems were mainly the hydrophobic ones and to a lesser extent the complexation of the Na⁺ ion by the PEG chains. Both of them were in favor of DCFNa, resulting in a larger incorporation and a slower release of this one in comparison with 5FU. For both drugs, loading was larger for hydrogels with shorter PEG chains and/or crosslinked with amines with longer hydrocarbon chain or higher functionality. Drug release tests showed a lower rate for stronger drug–network interactions in agreement with the absorption experiments.     

Tissue engineering scaffolds of mesoporous magnesium silicate and poly(ε-caprolactone)–poly(ethylene glycol)–poly(ε-caprolactone) composite

Mesoporous magnesium silicate (m-MS) and poly(ε-caprolactone)–poly(ethylene glycol)–poly(ε-caprolactone) (PCL–PEG–PCL) composite scaffolds were fabricated by solvent-casting and particulate leaching method. The results suggested that the incorporation of m-MS into PCL–PEG–PCL could significantly improve the water adsorption of the m-MS/PCL–PEG–PCL composite (m-MPC) scaffolds. The in vitro degradation behavior of m-MPC scaffolds were determined by testing weight loss of the scaffolds after soaking into phosphate buffered saline (PBS), and the result showed that the degradation of m-MPC scaffolds was obviously enhanced by addition of m-MS into PCL–PEG–PCL after soaking for 10 weeks. Proliferation of MG63 cells on m-MPC was significantly higher than MPC scaffolds at 4 and 7 days. ALP activity on the m-MPC was obviously higher than MPC scaffolds at 7 days, revealing that m-MPC could promote cell differentiation. Histological evaluation showed that the introduction of m-MS into PCL–PEG–PCL enhanced the efficiency of new bone formation when the m-MPC scaffolds implanted into bone defect of rabbits. The results suggested that the inorganic/organic composite of m-MS and PCL–PEG–PCL scaffolds exhibited good biocompatibility, degradability and osteogenesis.     

Particle formation and aggregation–collapse behavior of poly(N-isopropylacrylamide) and poly(ethylene glycol) block copolymers in the presence of cross-linking agent

The effect of feed molar ratio of N-isopropylacrylamide (NIPAM) to poly(ethylene oxide) (PEO) on the particle formation of poly(N-isopropylacrylamide) (PNIPAM) and PEO block copolymers (PNIPAM-b-PEO) and their aggregation-collapse behavior have been studied in aqueous solutions. It is found that in the presence of cross-linking agent N,N'-methylenebisacryla-mide (BIS), different morphologies of PNIPAM-b-PEO copolymers can be obtained, including a grafting-like structure, a hemispherical core-shell structure and a well-defined core-shell nanoparticle, as the feed molar amount of NIPAM in the copolymerization is increased. The increase in temperature causes the self-aggregation of grafting-like copolymers and hemispherical particles due to the hydrophobic interaction between locally unshielded PNIPAM blocks prior to the conformational transition of PNIPAM. When the feed molar ratio of NIPAM to PEO exceeds a certain value, a well-defined core-shell nanoparticle can be produced during the copolymerization. At low concentrations, PNIPAM cores of single core-shell nanoparticles can undergo the conformational transition without aggregation. The increase in the concentration of the well-defined core-shell nanoparticles, however, results in a week aggregation at temperatures lower than the theta-temperature of pure PNIPAM due to the association of methyl groups at the periphery of PEO shells.     

Preparation and characterization of magnetic poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) microspheres

In this article, nano-magnetite particles (ferrofluid, Fe₃O₄) were prepared by chemical co-deposition method. A series of biodegradable triblock poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) (PCL-PEG-PCL, PCEC) copolymers were synthesized by ring-opening polymerization method from ε-caprolactone (ε-CL) initiated by poly(ethylene glycol) diol (PEG) using stannous octoate as catalyst. And the magnetic PCEC composite microspheres were prepared by solvent diffusion method. The properties of the ferrofluid, PCEC copolymer, and magnetic PCEC microspheres were studied in detail by SEM, VSM, XRD, Malvern Laser Particle Sizer, ¹H-NMR, GPC, and TG/DTG. Effects of macromolecular weight and concentration of polymer, and the time for ultrasound dispersion on properties of magnetic microspheres were also investigated. The obtained magnetic PCEC microspheres might have great potential application in targeted drug delivery system or cell separation. This work was financially supported by Chinese Key Basic Research Program (2004CB518800 and 2004CB518807), and Sichuan Key Project of Science and Technology (06(05SG022-021-02)). Qian ZY and Wang H did the even work with Gou ML, and are the co-first authors for this paper.     

Microencapsulation of cytarabine using poly(ethylene glycol)–poly(ε-caprolactone) diblock copolymers as surfactant agents

Background: The high water solubility and the low molecular weight of cytarabine (Ara-C) are major obstacles against its particulate formulation as a result of its low affinity to the commonly used hydrophobic polymers. Methods: Biodegradable cytarabine loaded-microparticles (Ara-C MPs) were elaborated using poly(?-caprolactone) (PCL) and monomethoxy polyethylene glycol (mPEG)–PCL diblock copolymer in order to increase the hydrophilicity of the polymeric matrix. For this purpose, a series of mPEG–PCL diblock copolymers with different PCL block lengths were synthesized. Compositions and molecular weights of obtained copolymers were characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance, size exclusion chromatography, and size exclusion chromatography–multi-angle laser light scattering. Ara-C MPs were prepared by double emulsion-solvent evaporation method. The effects of varying PCL block lengths on microparticle encapsulation efficiency, size, and zeta potential were evaluated. Results: Increasing the PCL block lengths of copolymers substantially increased the Ara-C encapsulation efficiency and the microparticle size but it decreased their zeta potential. Microparticles were spherical in shape, with a smooth surface and composed of homogenously distributed Ara-C-containing aqueous domains in the polymer matrix. The in vitro drug release kinetics of the optimized microparticles showed a hyperbolic profile with an initial burst release. Conclusion: These results showed the important role of the amphiphilic diblock copolymers as stabilizing agent in the encapsulation of Ara-C in PCL microparticles, suggesting their potential use for the microparticulate formulations of other small hydrophilic bioactive molecules.     

Interpenetrating polymer networks (IPN) based on gelatin/poly(ethylene glycol) dimethacrylate/clay nanocomposites: Structure–properties relationship

The effects of cross-linking sequence (simultaneous or sequential) and incorporation of exfoliated sodium-montmorillonite (Na⁺-MMT) nanoclay on the structure and properties of interpenetrating polymer networks (IPNs) based on gelatin/poly(ethylene glycol)dimethacrylate were studied by means of different complementary techniques. Gelatin and PEGdmA phases were cross-linked via chemical and in-situ UV curing, respectively. 2,2-dimethoxy-2-phenylacetophenone (DMPA) (1.5% w/w) was used as photo-initiator to cross-link PEGdmA. The results showed that the incorporation of small amount of Na⁺-MMT nanoplatelets accelerates the kinetics of chemical cross-linking of gelatin by glutaraldehyde (1.0% w/w). This led to a new hypothesis concerning the tuning structural evolution of the IPNs by the Na⁺-MMT content. In the case of simultaneous IPNs, in which both phases cross-linked at the same time, the accelerated cross-linking of gelatin in the presence of exfoliated sodium-montmorillonite led to increased structural homogeneity, improved mechanical and thermal properties. Incorporation of nanoclay did not show any significant effect on the structure and properties of the IPNs synthesized via sequential method in which gelatin and PEGdma phases were cross-linked separately. For the semi-IPNs, however, Na⁺-MMT induced macroscopic phase separation and resulted in lower mechanical properties. These results might shed light on the mechanisms underlying structure–property relationship in biohybrid IPNs based on gelatin as promising candidates for tissue engineering and drug delivery applications.     

Synthesis, characterization and hydrolytic degradation study of polyetheresteramide copolymers based on ε-caprolactone, 6-aminocaproic acid, and poly(ethylene glycol)

In this paper, a new kind of biodegradable aliphatic polyetheresteramide copolymers (PEEA) based on -caprolactone, 6-aminocaproic acid, and poly(ethylene glycol) (PEG) were synthesized by melt polymerization method. The obtained copolymers were characterized by ¹H-NMR. The thermal properties of PEEA copolymers were studied by DSC and TGA/DTA under nitrogen atmosphere. The water absorption and hydrolytic degradation behavior was also studied in detail. With the increase in PEG content or the decrease in caprolactone content, the water absorption of the copolymers increased accordingly. For the hydrolytic degradation behavior, with the increase in PEG content or caprolactone content, the degradation rate increased then.     

Ocular Permeability of Pirenzepine Hydrochloride Enhanced by Methoxy poly(ethylene glycol)–poly(D,L-lactide) Block Copolymer

Methoxy poly(ethylene glycol)–poly(D,L-lactide) block copolymer was tested as an ocular permeation enhancer for pirenzepine hydrochloride. The block copolymers with the methoxy poly(ethylene glycol) to poly(D,L-lactide) weight ratio of 80/20, 50/50, 40/60 were synthesized by a ring-opening polymerization procedure. In vitro transcorneal experiments demonstrated that the block copolymer 80/20 significantly enhanced the transcorneal permeation of pirenzepine at the mass ratio of 1/1.4 (pirenzepine hydrochloride/copolymer). Interaction between pirenzepine and copolymer was identified by infrared spectroscopy analysis and dialysis experiments. Ocular pharmacokinetics of pirenzepine/copolymer preparation by in vivo instillation experiments confirmed that block copolymer could enhance the ocular penetration of pirenzepine. Ocular chronic toxicity experiments of block copolymer and pirenzepine/copolymer preparation were studied on rabbits, and no significant toxicity in both groups was observed within 9 months. It could conclude that pirenzepine/copolymer preparation is effective and safe in ocular delivery of pirenzepine.     

Composition-dependent physical properties of poly[(vinylidene fluoride)-co-trifluoroethylene]–poly(ethylene oxide) blends

Polymer blends based on poly(vinylidene fluoride-co-trifluoroethylene) copolymers, P(VDF-TrFE), and poly(ethylene oxide), PEO, with varying compositions have been prepared by solvent casting. In this way, P(VDF-TrFE) crystallizes from the solution while solvent evaporates, while PEO crystallizes from the melt during cooling to room temperature. The surface morphology of the polymer blends indicates the transition from the fibrillar microstructure typical of PVDF-TrFE to the spherulite structure characteristic of PEO. The vibration mode characteristics of P(VDF-TrFE) are not influenced by the presence of PEO in the polymer blend. Confinement of PEO in the P(VDF-TrFE) phase change the conformation of PEO from trans to helix, increasing this transformation for increasing P(VDF-TrFE) content in the polymer blends. Sequential crystallization of the two polymers produce separated amorphous phases whose independent cooperative conformational motions are revealed by two main dynamic-mechanical relaxations. No chemical interaction seems to exist between the polymers within the blend.     

Thermal behaviour of poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) tri-block copolymers

Thermal behavior of poly(-caprolactone)-poly(ethylene glycol)-poly(-caprolactone) tri-block copolymers with different block lengths is examined. Thermal behavior of specimens crystallized under the isothermal and dynamic condition are characterized by DSC. Also WAXD and SAXS are employed to investigate the structure. Depending on the relative length of each block, tri-block copolymers can be classified into three groups: PCL dominant crystallization; PEG dominant crystallization; and the competing case. When the crystallization of PEG and PCL are competing, the crystallization of each block shows strong dependency on the thermal hystory of crystallization, leading to multiple melting and crystallization peaks. Also, the typical micro-phase separation of block copolymers seems to play an important role, competing with crystallization, especially under the dynamic crystallization condition.     

Folate-mediated solid–liquid lipid nanoparticles for paclitaxel-coated poly(ethylene glycol)

Background: As a promising anticancer drug, severe side-effects of current clinical formulations for paclitaxel have restricted its use, developing a better technical-economical formulation for paclitaxel delivery is needed. Method: In this study, the compound of folate-poly(ethylene glycol) (PEG)-phosphatidylethanolamine was synthesized and characterized with Fourier transform infrared spectroscopy and nuclear magnetic resonance spectroscopy. The solid-liquid lipid nanoparticle (SLLN) for paclitaxel modified with folate and poly(ethylene glycol) (folate-PEG-SLLN) was prepared and characterized. Morphology of folate-PEG-SLLN was examined by transmission electron microscopy. The particle size and zeta potential were performed by Zetapals. Encapsulation efficiency was analyzed by HPLC. The in vitro drug release of paclitaxel was investigated via membrane dialysis. The in vivo pharmacokinetics was measured with male Sprague-Dawley rats. Treatment efficiency was investigated with the mouse with sarcoma180 ascites tumor. Results: Paclitaxel loaded on the newly designed binary SLLN showed a longer and sustained in vitro releasing property. More importantly, S180 tumor-bearing mice treated with paclitaxel-loaded SLLN exhibited higher tumor inhibition rate, comparing with animals administered with paclitaxel injection alone (45.3% and 37.3%, respectively). Conclusion: The newly developed paclitaxel delivery system may have improved in vivo antitumor activity. The results demonstrated a great interest to use folate-mediated SLLN as a prospective drug delivery system for paclitaxel.     

Encapsulation and controlled release of lysozyme from electrospun poly(ε-caprolactone)/poly(ethylene glycol) non-woven membranes by formation of lysozyme–oleate complexes

In this study, the concept of hydrophobic ion pairing was adopted for incorporating lysozyme into electrospun poly(ε-caprolactone) (PCL)/poly(ethylene glycol) (PEG) non-woven membranes. The solubility of lysozyme in organic solvent was enhanced through the formation of lysozyme–oleate complexes, which could be directly loaded into PCL/PEG membranes using electrospinning technique. The resultant PCL/PEG nanofibers have a compact structure with an average diameter ranged from about 0.4 μm to 0.9 μm. The addition of PEG into the PCL nanofibers not only improved the hydrophilicity of the membrane, but also played an important role on in vitro lysozyme release rate. It was found that the release rate of lysozyme was enhanced with the increase of PEG content. In addition, the increase of salt concentration in the release medium accelerated lysozyme release. It has also been shown that the released lysozyme retained most of its enzymatic activity.     

Modulating the mechanical properties of photopolymerised polyethylene glycol–polypropylene glycol hydrogels for bone regeneration

Hydrogels formulated from single polymers are often insufficient in terms of their mechanical properties for use as bone substitute materials. Hence, hydrogels synthesised from combinations of polymers have been investigated to optimise the performance of such materials. In the current study, polypropylene glycol dimethacrylate was added to polyethylene glycol dimethacrylate of a variety of molecular weights and photopolymerised to form a series of hydrogels. Polyethylene glycol and polypropylene glycol have the same chemical structure with the exception of a methyl group on the later. Herein, the influence of the methyl group of polypropylene glycol on the mechanical properties of hydrogels for bone regeneration applications is reported. For both unconfined and cyclic compression testing, results demonstrated that the incorporation of PEGDMA into the precursor improves the compression strength of the hydrogels. For example, in unconfined compression tests the Young’s modulus varied between 6.62?±?0.31?MPa and 8.08?±?0.81?MPa with the incorporation of PEGDMA 400.     

Structure,swelling, and drug release of thermoresponsive poly(amidoamine) dendrimer–poly(N-isopropylacrylamide) hydrogels

Functional drug delivery systems are important for improved pharmacotherapy. The aim of this work was to describe how the introduction of varying amounts of the dendrimer polyamidoamine (PAMAM) into a chemically cross-linked thermoresponsive poly(N-isopropylacrylamide) (PNIPAAM) gel affects the structure, swelling properties, and drug release characteristics. The structure of the gel system was characterized by small-angle X-ray scattering (SAXS), while the drug delivery system was characterized by measuring the swelling, loading, and release of the model drug. The SAXS results suggest that the PNIPAAM gel is heterogeneous on a local length scale, whereas more homogeneous gels are formed in the presence of PAMAM. Increased swelling and loading capacity were observed for higher fractions of PAMAM dendrimer. This was explained by the enhanced hydrophilicity obtained by inclusion of the dendrimers. The swelling process was observed to be very slow taking place over several days, indicating other mechanisms than diffusion to be the rate-limiting step. The temperature-induced deswelling was more pronounced for the dendrimer-containing formulations. This process was observed to be very fast and complete within a couple of hours. Similarly the release rate was quite fast without being affected by inclusion of the dendrimer. Retention of a significant portion of the loaded drug at specific conditions was shown to be due to the hydrogen bonding ability of PNIPAAM. Improved conditions for drug delivery were achieved in several respects by incorporation of PAMAM dendrimer molecules in the PNIPAAM hydrogel. Our results indicate that the PAMAM entities expand the PNIPAAM gel and that the gel becomes more homogeneous.     

A fully biocompatible poly(ethylene glycol)–gold plasmonic crystal for optical sensing

A significant challenge in nano and biophotonics is to demonstrate fully biocompatible nano-optics devices that can perform biofunctions in vivo. Here we present a scalable, cost-effective, and large-area nanofabrication method for creating a quasi-3D plasmonic crystal using poly(ethylene glycol) (PEG) and gold (Au), both biocompatible materials. The plasmonic crystal was prepared by depositing an Au layer on the upper hemisphere of the replicated PEG nanospheres array. Additionally we demonstrated that the fabricated plasmonic crystal can behave as a label-free glucose sensor with sensitivity and figure-of-merit values comparable to other plasmonic crystal based sensors.     

β-Crystal in injection moulded poly(ethylene terephthalate) fibre/isotactic polypropylene composite

The poly(ethylene terephthalate) (PET) fibre/isotactic polypropylene (iPP) composite was moulded by a mixing-injection moulding machine developed in our group. The molecular orientation and crystallinity of β-crystal were investigated by two-dimensional wide-angle X-ray diffraction (2D-WAXD), and shish-kebab structure was detected by two-dimensional small-angle X-ray scattering (2D-SAXS). In addition, crystalline morphology of β-crystal in different regions was observed by scanning electron microscope (SEM). As well known, PET fibre generally serves as heterogeneous nucleating agent for iPP to induce α-crystal. Unexpectedly, a remarkably increasing crystallinity of β-crystal from skin to core region was obtained in the present work, which is substantially different from other studies. Two origins of β-crystal developed in core region are proposed: (a) local shear caused by the different flow rates of molten iPP and solid PET fibre; (b) survived smectic ordering brought by the rotating screw during plasticization and melt mixing in barrel.