Effluent dissolved organic nitrogen and dissolved phosphorus removal by enhanced coagulation and microfiltration

Plants aiming to achieve very low effluent nutrient levels (<3 mg N/L for N, and <0.1 mg P/L for P) need to consider removal of effluent fractions hitherto not taken into account. Two of these fractions are dissolved organic nitrogen (DON) and dissolved non-reactive phosphorus (DNRP) (mainly composed of organic phosphorus). In this research, enhanced coagulation using alum (at doses commonly employed in tertiary phosphorus removal) followed by microfiltration (using 0.22 μm pore size filters) was investigated for simultaneous effluent DON and dissolved phosphorus (DP) fractions removal. At an approximate dose of 3.2 mg Al(III)/L, corresponding to 1.5 Al(III)/initial DON-N and 3.8 Al(III)/initial DP-P molar ratios, maximum simultaneous removal of DON and DP was achieved (69% for DON and 72% for DP). At this dose, residual DON and DP concentrations were found to be 0.3 mg N/L and 0.25 mg P/L, respectively. Analysis of the trends of removal revealed that the DNRP removal pattern was similar to that commonly reported for dissolved reactive phosphorus. Since this study involved intensive analytical work, a secondary objective was to develop a simple and accurate measurement protocol for determining dissolved N and P species at very low levels in wastewater effluents. The protocol developed in this study, involving simultaneous digestion for DON and DNRP species, was found to be very reliable and accurate based on the results.     

Fate of dissolved organic nitrogen in two stage trickling filter process

Dissolved organic nitrogen (DON) represents a significant portion of nitrogen in the final effluent of wastewater treatment plants (WWTPs). Biodegradable portion of DON (BDON) can support algal growth and/or consume dissolved oxygen in the receiving waters. The fate of DON and BDON has not been studied for trickling filter WWTPs. DON and BDON data were collected along the treatment train of a WWTP with a two-stage trickling filter process. DON concentrations in the influent and effluent were 27% and 14% of total dissolved nitrogen (TDN). The plant removed about 62% and 72% of the influent DON and BDON mainly by the trickling filters. The final effluent BDON values averaged 1.8 mg/L. BDON was found to be between 51% and 69% of the DON in raw wastewater and after various treatment units. The fate of DON and BDON through the two-stage trickling filter treatment plant was modeled. The BioWin v3.1 model was successfully applied to simulate ammonia, nitrite, nitrate, TDN, DON and BDON concentrations along the treatment train. The maximum growth rates for ammonia oxidizing bacteria (AOB) and nitrite oxidizing bacteria, and AOB half saturation constant influenced ammonia and nitrate output results. Hydrolysis and ammonification rates influenced all of the nitrogen species in the model output, including BDON.     

Adsorption of dissolved natural organic matter by modified activated carbons

Adsorption of dissolved natural organic matter (DOM) by virgin and modified granular activated carbons (GACs) was studied. DOM samples were obtained from two water treatment plants before (i.e., raw water) and after coagulation/flocculation/sedimentation processes (i.e., treated water). A granular activated carbon (GAC) was modified by high temperature helium or ammonia treatment, or iron impregnation followed by high temperature ammonia treatment. Two activated carbon fibers (ACFs) were also used, with no modification, to examine the effect of carbon porosity on DOM adsorption. Size exclusion chromatography (SEC) and specific ultraviolet absorbance (SUVA(254)) were employed to characterize the DOMs before and after adsorption. Iron-impregnated (HDFe) and ammonia-treated (HDN) activated carbons showed significantly higher DOM uptakes than the virgin GAC. The enhanced DOM uptake by HDFe was due to the presence of iron species on the carbon surface. The higher uptake of HDN was attributed to the enlarged carbon pores and basic surface created during ammonia treatment. The SEC and SUVA(254) results showed no specific selectivity in the removal of different DOM components as a result of carbon modification. The removal of DOM from both raw and treated waters was negligible by ACF10, having 96% of its surface area in pores smaller than 1 nm. Small molecular weight (MW) DOM components were preferentially removed by ACF20H, having 33% of its surface area in 1--3 nm pores. DOM components with MWs larger than 1600, 2000, and 2700 Da of Charleston raw, Charleston-treated, and Spartanburg-treated waters, respectively, were excluded from the pores of ACF20H. In contrast to carbon fibers, DOM components from entire MW range were removed from waters by virgin and modified GACs.     

Measurements of dissolved organic nitrogen (DON) in water samples with nanofiltration pretreatment

Dissolved organic nitrogen (DON) measurements for water samples with a high dissolved inorganic nitrogen (DIN, including nitrite, nitrate and ammonia) to total dissolved nitrogen (TDN) ratio using traditional methods are inaccurate due to the cumulative analytical errors of independently measured nitrogen species (TDN and DIN). In this study, we present a nanofiltration (NF) pretreatment to increase the accuracy and precision of DON measurements by selectively concentrating DON while passing through DIN species in water samples to reduce the DIN/TDN ratio. Three commercial NF membranes (NF90, NF270 and HL) were tested. The rejection efficiency of finished water from the Yangshupu drinking water treatment plant (YDWTP) is 12%, 31%, 8% of nitrate, 26%, 28%, 23% of ammonia, 77%, 78%, 82% of DOC (dissolved organic carbon), and 83%, 87% 88% of UV₂₅₄ for HL, NF90 and NF270, respectively. NF270 showed the best performance due to its high DIN permeability and DON retention (∼80%). NF270 can lower the DIN/TDN ratio from around 1 to less than 0.6 mg N/mg N, and satisfactory DOC recoveries as well as DON measurements in synthetic water samples were obtained using optimized operating parameters. Compared to the available dialysis pretreatment method, the NF pretreatment method shows a similar improved performance for DON measurement for aqueous samples and can save at least 20 h of operating time and a large volume of deionized water, which is beneficial for laboratories involved in DON analysis. DON concentration in the effluent of different treatment processes at the YDWTP and the SDWTP (Shijiuyang DWTP) in China were investigated with and without NF pretreatment; the results showed that DON with NF pretreatment and DOC both gradually decreased after each water treatment process at both treatment plants. The advanced water treatment line, including biological pretreatment, clarification, sand filtration, ozone-BAC processes at the SDWTP showed greater efficiency of DON removal from 0.37 to 0.11 mg N L⁻¹ than that at the YDWTP, including pre-ozonation, clarification and sand filtration processes from 0.18 to 0.11 mg N L⁻¹.     

Development and application of functional assays for freshwater dissolved organic matter

A series of 11 standardised, reproducible, assays have been developed of physico-chemical functions of dissolved organic matter (DOM) in freshwaters. The assays provide quantitative information on light absorption, fluorescence, photochemical fading, pH buffering, copper binding, benzo(a)pyrene binding, hydrophilicity and adsorption to alumina. To obtain DOM for the assays, a 45 L sample of filtered freshwater was rotary-evaporated to reduce the volume to ca. 500 cm3. The concentrate was then passed through a strong cation exchanger, in the Na+ form, to remove alkaline-earth cations, and then through 0.7 and 0.2 microm filters. Eight samples, two each from a lake and three streamwaters, were processed. The yields of dissolved organic carbon (DOC) ranged from 70% to 107% (average 91%). The samples of DOM, stored in the dark at 4 degrees C, retained their functional assay characteristics for up to 7 months. When assaying the concentrates, parallel assays were performed with Suwannee River fulvic acid (SRFA), as a quality control standard. For most of the assays, the results for eight freshwater DOM samples are similar to those obtained with SRFA, the chief exception being the greater hydrophilicity of the DOM samples. For eight of the assays, variability among the DOM samples is significantly (p < 0.01) greater than can be explained by analytical error, i.e. by comparison with results for the SRFA quality standard; the three exceptional assays are photochemical fading, copper binding and benzo(a)pyrene binding. The two lakewater samples studied gave the most extreme assay results, probably because of the influence of phytoplankton-derived DOM. Significant correlations of hydrophilicity and adsorption with optical absorbance may mean that some DOM functional properties can be predicted from comparatively simple measurements.     

Characterization of natural organic matter adsorption in granular activated carbon adsorbers

The removal of natural organic matter (NOM) from lake water was studied in two pilot-scale adsorbers containing granular activated carbon (GAC) with different physical properties. To study the adsorption behavior of individual NOM fractions as a function of time and adsorber depth, NOM was fractionated by size exclusion chromatography (SEC) into biopolymers, humics, building blocks, and low molecular weight (LMW) organics, and NOM fractions were quantified by both ultraviolet and organic carbon detectors. High molecular weight biopolymers were not retained in the two adsorbers. In contrast, humic substances, building blocks and LMW organics were initially well and irreversibly removed, and their effluent concentrations increased gradually in the outlet of the adsorbers until a pseudo-steady state concentration was reached. Poor removal of biopolymers was likely a result of their comparatively large size that prevented access to the internal pore structure of the GACs. In both GAC adsorbers, adsorbability of the remaining NOM fractions, compared on the basis of partition coefficients, increased with decreasing molecular size, suggesting that increasingly larger portions of the internal GAC surface area could be accessed as the size of NOM decreased. Overall DOC uptake at pseudo-steady state differed between the two tested GACs (18.9 and 28.6 g-C/kg GAC), and the percent difference in DOC uptake closely matched the percent difference in the volume of pores with widths in the 1-50 nm range that was measured for the two fresh GACs. Despite the differences in NOM uptake capacity, individual NOM fractions were removed in similar proportions by the two GACs.     

Measurement of dissolved organic nitrogen in a drinking water treatment plant: size fraction, fate, and relation to water quality parameters

This paper investigates the characteristics of dissolved organic nitrogen (DON) in raw water from the Huangpu River and also in water undergoing treatment in the full-scale Yangshupu drinking water treatment plant (YDWTP) in Shanghai, China. The average DON concentration of the raw water was 0.34 mg/L, which comprised a relatively small portion (~ 5%) of the mass of total dissolved nitrogen (TDN). The molecular weight (MW) distribution of dissolved organic matter (DOM) was divided into five groups: > 30, 10-30, 3-10, 1-3 and < 1 kDa using a series of ultrafiltration membranes. Dissolved organic carbon (DOC), UV absorbance at wavelength of 254 nm (UV254) and DON of each MW fraction were analyzed. DON showed a similar fraction distribution as DOC and UV254. The < 1 kDa fraction dominated the composition of DON, DOC and UV254 as well as the major N-nitrosodimethylamine formation potential (NDMAFP) in the raw water. However, this DON fraction cannot be effectively removed in the treatment line at the YDWTP including pre-ozonation, clarification and sand filtration processes. The results from linear regression analysis showed that DON is moderately correlated to DOC, UV254 and trihalomethane formation potential (FP), and strongly correlated to haloacetic acids FP and NDMAFP. Therefore, DON could serve as a surrogate parameter to evaluate the reactivity of DOM and disinfection by-products FP.     

UV-induced photochemical heterogeneity of dissolved and attached organic matter associated with cyanobacterial blooms in a eutrophic freshwater lake

Cyanobacterial blooms represent a significant ecological and human health problem worldwide. In aquatic environments, cyanobacterial blooms are actually surrounded by dissolved organic matter (DOM) and attached organic matter (AOM) that bind with algal cells. In this study, DOM and AOM fractionated from blooming cyanobacteria in a eutrophic freshwater lake (Lake Taihu, China) were irradiated with a polychromatic UV lamp, and the photochemical heterogeneity was investigated using fluorescence excitation–emission matrix (EEM)-parallel factor (PARAFAC) analysis and synchronous fluorescence (SF)-two dimensional correlation spectroscopy (2DCOS). It was shown that a 6-day UV irradiation caused more pronounced mineralization for DOM than AOM (59.7% vs. 41.9%). The EEM-PARAFAC analysis identified one tyrosine-, one humic-, and two tryptophan-like components in both DOM and AOM, and high component photodegradation rates were observed for DOM versus AOM (k > 0.554 vs. <0.519). Moreover, SF-2DCOS found that the photodegradation of organic matters followed the sequence of tyrosine-like > humic-like > tryptophan-like substances. Humic-like substances promoted the indirect photochemical reactions, and were responsible for the higher photochemical rate for DOM. The lower photodegradation of AOM benefited the integrality of cells in cyanobacterial blooms against the negative impact of UV irradiation. Therefore, the photochemical behavior of organic matter was related to the adaptation of enhanced-duration cyanobacterial blooms in aquatic environments.     

Tracking natural organic matter (NOM) in a drinking water treatment plant using fluorescence excitation-emission matrices and PARAFAC

Natural organic matter (NOM) in water samples from a drinking water treatment train was characterized using fluorescence excitation emission matrices (F-EEMs) and parallel factor analysis (PARAFAC). A seven component PARAFAC model was developed and validated using 147 F-EEMs of water samples from two full-scale water treatment plants. It was found that the fluorescent components have spectral features similar to those previously extracted from F-EEMs of dissolved organic matter (DOM) from diverse aquatic environments. Five of these components are humic-like with a terrestrial, anthropogenic or marine origin, while two are protein-like with fluorescence spectra similar to those of tryptophan-like and tyrosine-like fluorophores. A correlation analysis was carried out for samples of one treatment plant between the maximum fluorescence intensities (F_max) of the seven PARAFAC components and NOM fractions (humics, building blocks, neutrals, biopolymers and low molecular weight acids) of the same sample obtained using liquid chromatography with organic carbon detection (LC-OCD). There were significant correlations (p < 0.01) between sample DOC concentration, UVA₂₅₄, and F_max for the seven PARAFAC components and DOC concentrations of the LC-OCD fractions. Three of the humic-like components showed slightly better predictions of DOC and humic fraction concentrations than UVA_254. Tryptophan-like and tyrosine-like components correlated positively with the biopolymer fraction. These results demonstrate that fluorescent components extracted from F-EEMs using PARAFAC could be related to previously defined NOM fractions and that they could provide an alternative tool for evaluating the removal of NOM fractions of interest during water treatment.     

Freeze/thaw and pH effects on freshwater dissolved organic matter fluorescence and absorbance properties from a number of UK locations

The UV-visible and fluorescence excitation-emission matrix spectrophotometric properties of dissolved organic matter (DOM) were compared for the effects of both pH and freeze/thaw on a wide range of freshwater DOM samples from the United Kingdom. It was observed that the spectrophotometric properties of our freshwater samples were sensitive to pH and that the recorded change varies with fluorescence and absorbance intensity, DOC concentration and the wavelength observed. Large and variable responses to pH were particularly severe at extremes of pH, but within the natural levels typically observed in freshwaters the response to pH was limited. For the same sample set large and variable responses were observed when subjected to freeze/thaw. From our data, knowledge of the original properties cannot be used to determine the amount of change that will occur with freezing and subsequent thawing. It is therefore recommended that in future research, to maintain the natural signal of the DOM, analysis is conducted at natural pH and without freezing to facilitate ease of comparison between studies. Our results also have implications for studies that utilise spectrophotometric techniques to investigate long-term trends in dissolved organic carbon in rivers. Spectrophotometric parameters from upland derived samples show varied responses of samples to pH and there is clear potential to complicate trends in the interpretation of long-term water colour data if pH is changing over time in a system or if samples are treated with different storage protocols with respect to acidification and freezing.     

Photo-dissolution of flocculent, detrital material in aquatic environments: contributions to the dissolved organic matter pool

This study shows that light exposure of flocculent material (floc) from the Florida Coastal Everglades (FCE) results in significant dissolved organic matter (DOM) generation through photo-dissolution processes. Floc was collected at two sites along the Shark River Slough (SRS) and irradiated with artificial sunlight. The DOM generated was characterized using elemental analysis and excitation emission matrix fluorescence coupled with parallel factor analysis. To investigate the seasonal variations of DOM photo-generation from floc, this experiment was performed in typical dry (April) and wet (October) seasons for the FCE. Our results show that the dissolved organic carbon (DOC) for samples incubated under dark conditions displayed a relatively small increase, suggesting that microbial processes and/or leaching might be minor processes in comparison to photo-dissolution for the generation of DOM from floc. On the other hand, DOC increased substantially (as much as 259 mgC gC⁻¹) for samples exposed to artificial sunlight, indicating the release of DOM through photo-induced alterations of floc. The fluorescence intensity of both humic-like and protein-like components also increased with light exposure. Terrestrial humic-like components were found to be the main contributors (up to 70%) to the chromophoric DOM (CDOM) pool, while protein-like components comprised a relatively small percentage (up to 16%) of the total CDOM. Simultaneously to the generation of DOC, both total dissolved nitrogen and soluble reactive phosphorus also increased substantially during the photo-incubation period. Thus, the photo-dissolution of floc can be an important source of DOM to the FCE environment, with the potential to influence nutrient dynamics in this system.     

Effects of reverse osmosis isolation on reactivity of naturally occurring dissolved organic matter in physicochemical processes

A field reverse osmosis system was used to isolate dissolved organic matter (DOM) from two lacustrine and two riverine surface water sources. The rejection of DOM was on the order of 99% and did not vary significantly with pressure. A simple mass balance model using a single measured value of rejection predicted the concentration within the closed-loop isolation system. The effect of operating pressure and solution flux on mass recovery of DOM was evaluated in laboratory and field trials. Under controlled laboratory conditions, >99% of a lacustrine DOM could be accounted for. A fraction of the isolated DOM was not recoverable using hydrodynamic cleaning; however, this fraction was recovered by using a pH 10 NaOH wash solution. The mass recovered in the NaOH solution increased from <1% to >6% with increasing transmembrane pressures from 414 kPa (60 psi) to1000 kPa (145 psi), respectively. This is consistent with fouling that results from an increase in solution flux, and a decrease in tangential crossflow velocity. Under field conditions, mass balances were generally >95% and mass recovery was >90% in all cases. The effects of temperature on solution flux were consistent with changes in fluid viscosity; effects of temperature on membrane diffusivity or morphological properties were small. RO isolation under low pressure conditions designed to maximize DOM recovery had little effect on DOM reactivity evaluated in terms of nanofiltration membrane fouling, XAD-8 resin adsorption, activated carbon adsorption, competition with trichloroethylene for adsorption sites on activated carbon, and molecular weight distribution measured using size exclusion chromatography.     

Reconsidering the quantitative analysis of organic carbon concentrations in size exclusion chromatography

The evaluation of the molecular size distribution of natural organic matter (NOM) in aquatic environments via size exclusion chromatography (SEC) is important for the understanding of environmental processes such as nutrient cycling and pollutant transport as well as of technical water treatment processes. The use of organic carbon (OC) detectors has become popular in recent studies due to improved availability and quantification possibilities, which supposedly are superior to those of ultraviolet (UV) detectors. A set of 12 NOM samples was used to demonstrate the limitations of online OC detection (OCD) when analyzing complex aquatic organic matter. A novel evaluation approach for SEC data is introduced by combining the information from UV absorbance (UVA) and OCD chromatograms as well as offline total OC (t-OC) and dissolved OC-specific UVA (SUVA) measurements. It could be shown that about 70% of certain OC components were not detected with the OCD system used in this study. For the investigated samples, these types of carbon accounted for up to 72% of the t-OC, i.e. for such NOM samples quantification by OCD is not possible or at least highly questionable. The addition of an oxidant improved the overall oxidation efficiency only slightly. Most likely NOM that predominantly consists of polysaccharides and features a nominal molecular weight of 150 kg/mol or more was responsible for low OCD yields. For future applications, a further improvement of the OCD system would be worthwhile so that quantitative analytical data on the molecular size distribution of NOM and its structural characteristics such as the SUVA distribution can be obtained.     

Spectrofluorometric properties of dissolved organic matter from Central and Southern Ontario streams and the influence of iron and irradiation

Fluorescence measurements were used to compare characteristics of dissolved organic matter (DOM) from distinctly different origins: boreal, agricultural and urban streams as well as a storm runoff pond and the outlet of a tertiary wastewater treatment plant. The primary goal was to determine if differences among stream types could be detected using DOM fluorescence in lieu of isolated fulvic acids (FA). Differences in peak excitation and peak emission wavelengths, fluorescence integrated over the 3-D matrix volume integrated fluorescence (VIF), and in a fluorescence index (FI) were examined. In general, peak fluorescence excitation and emission wavelengths as well as FI best distinguished DOM from the various origins. Results suggested that DOM from the boreal streams was of a higher molecular weight and more complex than that of agricultural and urban streams. The effects of irradiation as well as Fe on fluorescence of natural stream waters were also investigated, both of which decreased the ability of optical properties to distinguish DOM source.     

Characterization of dissolved organic matter in a submerged membrane bioreactor by using three-dimensional excitation and emission matrix fluorescence spectroscopy

Three-dimensional excitation-emission matrix (EEM) fluorescence spectroscopy was employed to characterize dissolved organic matter (DOM) in a submerged membrane bioreactor (MBR). Three fluorescence peaks could be identified from the EEM fluorescence spectra of the DOM samples in the MBR. Two peaks were associated with the protein-like fluorophores, and the third was related to the visible humic acid-like fluorophores. Only two main peaks were observed in the EEM fluorescence spectra of the extracellular polymeric substance (EPS) samples, which were due to the fluorescence of protein-like and humic acid-like matters, respectively. However, the EEM fluorescence spectra of membrane foulants were observed to have three peaks. It was also found that the dominant fluorescence substances in membrane foulants were protein-like substances, which might be due to the retention of proteins in the DOM and/or EPS in the MBR by the fine pores of the membrane. Quantitative analysis of the fluorescence spectra including peak locations, fluorescence intensity, and different peak intensity ratios and the fluorescence regional integration (FRI) analysis were also carried out in order to better understand the similarities and differences among the EEM spectra of the DOM, EPS, and membrane foulant samples and to further provide an insight into membrane fouling caused by the fluorescence substances in the DOM in submerged MBRs.     

Characterization of dissolved organic matter in drinking water sources impacted by multiple tributaries

The characterization of dissolved organic matter (DOM) in drinking water sources is important as this material contributes to the formation of disinfection by-products (DBPs) and affects how water treatment unit operations are optimized. Drinking water utilities often draw water from sources impacted by multiple tributaries, with possible shifts in DOM concentrations and reactivity over time, depending on specific environmental conditions. In this study, results are presented on the characterization of DOM under varying ambient conditions from the four main tributaries of Lake Mead, a large reservoir in the southwest United States. The tributaries include the Las Vegas Wash (LVW), Muddy River (MR), Virgin River (VR) and the upper Colorado River (UCR). One additional sample was collected at the outflow of the reservoir (lower Colorado River (LCR)). The DOM was characterized by both bulk parameters (specific ultraviolet absorbance (SUVA)) and specific physicochemical properties, i.e. size, polarity and fluorescence. The analyses were performed emphasizing limited changes in its natural configuration by eliminating analytical preparation steps, excluding sample filtration (0.45 microm filter). Results indicate that each tributary had a different molecular weight distribution, as well as fluorescence properties, which helped in the identification of the relative source of DOM (allochthonous versus autochthonous). The largest apparent molecular weight distribution was observed for DOM samples collected at the MR site, which is fed mostly by groundwater seepage. The smallest apparent molecular weight was observed for DOM collected at the LCR site, suggesting that retention in the reservoir resulted in a decrease in molecular weight as a probable result of photo oxidation and microbial processes. Fluorescence analysis aided the differentiation of DOM by clearly identifying waters that were affected by microbial activity (LVW, UCR, and LCR), either by wastewater influence or by autochthonous processes, versus limited microbial influence (MR and VR). Polarity analysis revealed clear differences in the hydrophobic/hydrophilic nature between waters, including temporal differences within individual waters at a particular site. The DOM from the LVW and VR sites had higher hydrophobic character, as measured by retention onto non-polar sorbents. Additionally, the DOM collected at the LCR had the least hydrophobic character. This type of analysis would be beneficial to utilities who want to better understand and manage their source waters, especially in the evaluation of temporal variation within a watershed.     

Complexity of ultrafiltration membrane fouling caused by macromolecular dissolved organic compounds in secondary effluents

Recent investigations indicate the relevance of extracellular polymeric substances (EPS) in terms of fouling of low-pressure membranes in advanced wastewater treatment. In this study, the high impact of the macromolecular fraction of effluent organic matter on fouling was confirmed in cross-flow ultrafiltration experiments using secondary effluent with and without autochthonous biopolymers. A method for the extraction of a natural mixture of EPS derived from the bacterium Sinorhizobium sp. is presented. Ultrafiltration of solutions of this bacterial EPS extract revealed a correlation between the concentration of EPS and the loss of permeate flux. However, in ultrafiltration tests using extracted bacterial EPS in a model solution as well as in secondary effluent without autochthonous biopolymers, the extent of membrane fouling was not identical with the fouling provoked by secondary effluent organic matter, although the biopolymer concentrations were comparable. The differences in the fouling behaviour of the extracted bacterial EPS and effluent organic matter are considered to be due to different compositions of the biopolymer fraction in terms of proteins, polysaccharides, and other organic colloids, indicating a particular impact of proteins on ultrafiltration membrane fouling.     

Sorption of phenols onto sandy aquifer material: the effect of dissolved organic matter (DOM)

The influence of dissolved organic matter (DOM) on the sorption of four phenols, 2,4,6-trichlorophenol (2,4,6-TCP), pentachlorophenol (PCP), 2,4-dinitrophenol (2,4-DNP) and 2-methyl-4,6-dinitrophenol (2-M-4,6-DNP), onto sandy aquifer material at different pH values was investigated using flow through column experiments. The pH-dependent sorption of the chlorinated phenols 2,4,6-TCP and PCP was not significantly affected by DOM (measured as dissolved organic carbon, DOC), whereas in the case of nitrophenols a significant lower retardation was found, depending on the DOC concentration and pH value of the aqueous solution. Sorption decreases with increasing DOC concentration, which indicates a binding of these compounds by DOM. The degree of sorption reduction depends on the pH value and increases with increasing fraction of neutral species. The different behaviour of nitrophenols in comparison to the chlorophenols is assumed to be a result of specific charge-transfer interactions. A combined sorption and complex formation model was used to describe the effect of pH and DOC concentration on the sorption of nitrophenols onto aquifer material and to estimate binding coefficients of neutral nitrophenols on DOM.     

Effects of mass retention of dissolved organic matter and membrane pore size on membrane fouling and flux decline

Ultrafiltration (UF) fouling has been attributed to concentration polarization, gel layer formation as well as outer and inner membrane pore clogging. It is believed that mass of humic materials either retained on membrane surface or associated with membrane inner pore surface is the primary cause for permeate flux decline and filtration resistance build-up in water supply industries. While biofilm/biofouling and inorganic matter could also be contributing factors for permeability decline in wastewater treatment practices. The present study relates UF fouling to mass of dissolved organic matter (DOM) retained on membrane and quantifies the effect of retained DOM mass on filtration flux decline. The results demonstrate that larger pore membranes exhibit significant flux decline in comparison with the smaller ones. During a 24-h period, dissolved organic carbon mass retained in 10 kDa membranes was about 1.0 g m⁻² and that in 100 kDa membranes was more than 3 times higher (3.6 g m⁻²). The accumulation of retained DOM mass significantly affects permeate flux. It is highly likely that some DOMs bind or aggregate together to form surface gel layer in the smaller 10 kDa UF system; those DOMs largely present in inner pore and serving as pore blockage on a loose membrane (100 kDa) are responsible for severe flux decline.     

Organic nitrogen transformations in a 4-stage Bardenpho nitrogen removal plant and bioavailability/biodegradability of effluent DON

Nitrogen species, specifically, the fate and occurrence of organic nitrogen (ON) within a 4-stage Bardenpho process bioreactor producing low total nitrogen (TN) effluents were investigated in this study. The results showed release of ON in primary anoxic zone and no ON release in the first aerobic zone of the process. The research included investigation of biodegradability/bioavailability of wastewater-derived effluent dissolved ON (DON). The final-effluent DON utilization was evaluated by two different bioassay protocols in the presence and absence of nitrate. About 28–57% of the effluent DON was bioavailable/biodegradable. Bioavailable (to algae and bacteria) DON (ABDON) and biodegradable (to bacteria) DON (BDON) results did not show significant differences in terms of quantity, but DON utilization rates by ABDON (0.13 day⁻¹) protocol were higher than that of the BDON (0.04 day⁻¹) protocol in the nitrate-removal samples. As a result, ABDON requires a shorter time to exert the bioavailable fraction due to symbiotic relationship between algae and bacteria. In the nitrate-containing samples, it appears that nitrate competes with labile DON as a nitrogen source to microorganisms in both ABDON and BDON protocols. The first order decay rate of DON in the presence of nitrate was 0.11 day⁻¹ and 0.02 day⁻¹ for ABDON and BDON, respectively.