Mechanical reliability of Sn-rich Au–Sn/Ni flip chip solder joints fabricated by sequential electroplating method

In this study, we evaluated the mechanical reliability of Sn-rich, Au–Sn/Ni flip chip solder bumps by using a sequential electroplating method with Sn and Au. After reflowing, the average diameter of the solder bump was approximately 80 μm and only a (Ni,Au)₃Sn₄ intermetallic compound (IMC) layer was formed at the interface. Due to the preferential consumption of Sn atoms within the solder matrix during aging, the solder matrix was transformed sequentially in the following order: β-Sn and η-phase, η-phase, and η-phase and ε-phase. In the bump shear test, the shear force was not significantly changed despite aging at 150 °C for 1000 h and most of the fractures occurred at the interfaces. The interfacial fracture was significantly related to the formation of brittle IMCs at the interface. The Sn-rich, Au–Sn/Ni flip chip joint was mechanically much weaker than the Au-rich, Au–Sn/Ni flip chip joint. The study results demonstrated that the combination of Sn-rich, Au–Sn solder and Ni under bump metallization (UBM) is not a viable option for the replacement of the conventional, Au-rich, Au–20Sn solder.     

Intermetallic reactions in Sn-3.5Ag solder ball grid array packages with Ag/Cu and Au/Ni/Cu pads

During the reflow process of Sn-3.5Ag solder ball grid array (BGA) packages with Ag/Cu and Au/Ni/Cu pads, Ag and Au thin films dissolve rapidly into the liquid solder, and the Cu and Ni layers react with the Sn-3.5Ag solder to form Cu₆Sn₅ and Ni₃Sn₄ intermetallic compounds at the solder/pad interfaces, respectively. The Cu₆Sn₅ intermetallic compounds also appear as clusters in the solder matrix of Ag surface-finished packages accompanied by Ag₃Sn dispersions. In the solder matrix of Au/Ni surface-finished specimens, Ag₃Sn and AuSn₄ intermetallics can be observed, and their coarsening coincides progressively with the aging process. The interfacial Cu₆Sn₅ and Ni₃Sn₄ intermetallic layers grow by a diffusion-controlled mechanism after aging at 100 and 150°C. Ball shear strengths of the reflowed Sn-3.5Ag packages with both surface finishes are similar, displaying the same degradation tendencies as a result of the aging effect.     

Cross-Interaction of Interfacial Reactions in Ni (Au/Ni/Cu)-SnAg-Cu Solder Joints during Reflow Soldering and Thermal Aging

Interfacial reactions in Ni-SnAg-Cu and Au/Ni/Cu-SnAg-Cu solder joints were investigated to understand the coupling effect between different pads during soldering and thermal aging processes. Scanning electron microscopy (SEM) was used to characterize the microstructures and phases. The element distributions in the joints were identified using the x-ray mapping technique. The thickness variation of intermetallic compounds (IMCs) with aging time was also measured. The results showed that interfacial reactions were not only affected by the compositions of solders and the local metallizations but the remote pads as well. The Au surface finish had an effect on the growth of IMCs at the interfaces. No redeposition of (Au, Ni)Sn₄ was found in the Au/Ni/Cu-SnAg-Cu solder joint. The effect of Cu on the formation of IMCs and redeposition of (Au, Ni)Sn₄ was also discussed. An erratum to this article can be found at     

Cross-Interaction Study of Cu/Sn/Pd and Ni/Sn/Pd Sandwich Solder Joint Structures

Cross-interactions between Cu/Sn/Pd and Ni/Sn/Pd sandwich structures were investigated in this work. For the Cu/Sn/Pd case, the growth behavior and morphology of the interfacial (Pd,Cu)Sn₄ compound layer was very similar to that of the single Pd/Sn interfacial reaction. This indicates that the growth of the (Pd,Cu)Sn₄ layer at the Sn/Pd interface would not be affected by the opposite Cu/Sn interfacial reaction. We can conclude that there is no cross-interaction effect between the two interfacial reactions in the Cu/Sn/Pd sandwich structure. For the Ni/Sn/Pd case, we observed that: (1) after 300 s of reflow time, the (Pd,Ni)Sn₄ compound heterogeneously nucleated on the Ni₃Sn₄ compound layer at the Sn/Ni interface; (2) the growth of the interfacial PdSn₄ compound layer was greatly suppressed by the formation of the (Pd,Ni)Sn₄ compound at the Sn/Ni interface. We believe that this suppression of PdSn₄ growth is caused by heterogeneous nucleation of the (Pd,Ni)Sn₄ compound in the Ni₃Sn₄ compound layer, which decreases the free energy of the entire sandwich reaction system. The difference in the chemical potential of Pd in the PdSn₄ phase at the Pd/Sn interface and in the (Pd,Ni)Sn₄ phase at the Sn/Ni interface is the driving force for the Pd atomic flux across the molten Sn. The diffusion of Ni into the ternary (Pd,Ni)Sn₄ compound layer controls the Pd atomic flux across the molten Sn and the growth of the ternary (Pd,Ni)Sn₄ compound at the Sn/Ni interface.     

Investigation of interfacial reaction between Sn-Ag eutectic solder and Au/Ni/Cu/Ti thin film metallization

This paper reports the formation of intermetallic compounds in Au/Ni/Cu/Ti under-bump-metallization (UBM) structure reacted with Ag-Sn eutectic solder. In this study, UBM is prepared by evaporating Au(500 Å)/Ni(1000 Å)/Cu(7500 Å) /Ti (700 Å) thin films on top of Si substrates. It is then reacted with Ag-Sn eutectic solder at 260 C for various times to induce different stages of the interfacial reaction. Microstructural examination of the interface, using both chemical and crystallographic analysis, indicates that two types of intermetallic compounds are formed during the interfacial reaction. The first phase, formed at the intial stage of the reaction, is predominantly Ni₃Sn₄. At longer times the Ni₃Sn₄ phase transforms into (Cu, Ni)₆Sn₆, probably induced by interdiffusion of Cu and Ni. At this stage, the underlying Cu layer also reacts with Sn and forms the same phase, (Cu,Ni)₆Sn₅. As a result, the fully reacted interface is found to consist of two intermetallic layers with the same phase but different morphologies.     

Intermetallic reactions in Sn3Ag0.5Cu and Sn3Ag0.5Cu0.06Ni0.01Ge solder BGA packages with Au/Ni surface finishes

The intermetallic compounds (IMCs) formed during the reflow and aging of Sn3Ag0.5Cu and Sn3Ag0.5Cu0.06Ni0.01Ge solder BGA packages with Au/Ni surface finishes were investigated. After reflow, the thickness of (Cu, Ni, Au)₆Sn₅ interfacial IMCs in Sn3Ag0.5Cu0.06Ni0.01Ge was similar to that in the Sn3Ag0.5Cu specimen. The interiors of the solder balls in both packages contained Ag₃Sn precipitates and brick-shaped AuSn₄ IMCs. After aging at 150°C, the growth thickness of the interfacial (Ni, Cu, Au)₃Sn₄ intermetallic layers and the consumption of the Ni surface-finished layer on Cu the pads in Sn3Ag0.5Cu0.06Ni0.01Ge solder joints were both slightly less than those in Sn3Ag0.5Cu. In addition, a coarsening phenomenon for AuSn₄ IMCs could be observed in the solder matrix of Sn3Ag0.5Cu, yet this phenomenon did not occur in the case of Sn3Ag0.5Cu0.06Ni0.01Ge. Ball shear tests revealed that the reflowed Sn3Ag0.5Cu0.06Ni0.01Ge packages possessed bonding strengths similar to those of the Sn3Ag0.5Cu. However, aging treatment caused the ball shear strength in the Sn3Ag0.5Cu packages to degrade more than that in the Sn3Ag0.5Cu0.06Ni0.01Ge packages.     

Influence of trace alloying elements on the ball impact test reliability of SnAgCu solder joints

In this work, we present ball impact test (BIT) responses and fracture modes obtained at an impact velocity of 0.8 m/s on SAC (Sn–Ag–Cu) package-level solder joints with a trace amount of Mn or RE (rare earth) additions, which were bonded with substrates of OSP Cu and electroplated Ni/Au surface finishes respectively. With respect to the as-mounted conditions, the Ni/Au joints possessed better impact fracture resistance than those with Cu substrate. Subsequent to aging at 150 °C for 800 h, multi-layered intermetallic compounds emerged at the interface of the Ni/Au joints and gave rise to degradation of the BIT properties. This can be prevented by RE doping, which is able to inhibit the growth of interfacial IMCs during aging. As for aged Cu joints, the Mn-doped samples showed the best performance in impact force and toughness. This was related to the hardened Sn matrix, and most importantly, a greater Cu₃Sn/Cu₆Sn₅ thickness ratio at the interface. Compared to Cu₆Sn₅, Cu₃Sn with a similar hardness but greater elastic modulus possessed better plastic ability, which was beneficial to the reliability of solder joints suffering high strain rate deformation if no excess Kirkendall voids formed.     

Analysis of the redeposition of AuSn<Subscript>4</Subscript> on Ni/Au contact pads when using SnPbAg,SnAg, and SnAgCu solders

Interfacial reactions between SnPbAg, SnAg, and SnAgCu solders and Ni/Au surface finish on printed wiring board and especially the redeposition of AuSn₄ intermetallic compound have been investigated. The following major results were obtained. The first phase to form during soldering in the (SnPbAg)/Ni/Au and the (SnAg)/Ni/Au systems was Ni₃Sn₄. During the subsequent solid-state annealing, the redeposition of AuSn₄ as (Au,Ni)Sn₄ occurred in both systems. This was explained with the help of the concept of local equilibrium and the corresponding ternary phase diagrams. It was concluded that the stabilizing effect of Ni on the (Au,Ni)Sn₄ provided the driving force for the redeposition. Contrarily, when the solder alloy contained some Cu, the first intermetallic to form was (Cu,Ni,Au)₆Sn₅ and no redeposition of AuSn₄ was observed. Thus, a very small addition of Cu to the Sn-rich solder alloys changed the behavior of the interconnection system completely. This behavior was explained thermodynamically by using Cu-Ni-Sn and Au-Cu-Sn ternary phase diagrams. The growth kinetics of the interfacial reaction products in the three systems was observed to be somewhat different. The reasons for the observed differences are also discussed.     

Selective formation of intermetallic compounds in Sn-20In-0.8Cu ball grid array solder joints with Au/Ni surface finishes

After Sn-20In-0.8Cu solder balls are reflowed on a ball grid array (BGA) substrate (substrate A) with an Au/Ni surface finish, scallop-shaped intermetallic compounds with a composition of 0.83[Cu₆(Sn_0.87In_0.13)₅] + 0.17[Ni₃(Sn_0.87In_0.13)₄] are formed at the solder/pad interface. The distribution of the intermetallics is not altered by gravity or by multiple reflows of the solder joints. As another substrate (substrate B) is further attached onto the primary reflowed BGA assembly to form a sandwich structure subjected to subsequent multiple reflows, the Cu₆(Sn_0.87In_0.13)₅ interfacial intermetallic scallops remain still on the side of substrate A while many Au(In_0.91Sn_0.09)₂ intermetallics of cubic shape appear near the solder/Ni interface on the side of substrate B. When the Sn-20In-0.8Cu solder balls are assembled simultaneously in between two substrates (A and B), Au(In_0.91Sn_0.09)₂ intermetallic cubes of equal proportion are observed to form on both sides of the assembly. In summarizing the results, it is proposed that the diffusion of Cu atoms in the Sn-20In-0.8Cu solder toward the Ni layers after Au thin-film dissolution on Au/Ni surface finishes led to the formation of Cu₆(Sn_0.87Zn_0.17)₅ intermetallic compounds, which prevailed over the gravitational effect so that no intermetallic sedimentation in the liquid solder would occur. The appearance of Au(In_0.91Sn_0.09)₂ at the Ni/Sn-20In-0.8Cu interfaces was hindered by the preferential formation of Cu₆(Sn_0.87Zn_0.17)₅ until the Cu atoms in the Sn-20In-0.8Cu solder matrix were consumed to a lower content via the attachment of a second substrate to the assembly.     

Reactive interdiffusion between a lead-free solder and Ti/Ni/Ag thin-film metallizations

The reactive interdiffusion between a Sn-3.0wt.%Ag-0.7wt.%Cu solder and thin-film Ti/Ni/Ag metallizations on two semiconductor devices, a diode and a metal-oxide-semiconductor field-effect transistor (MOSFET), and a Au-layer on the substrates are studied. Comprehensive microanalytical techniques, scanning electron microscopy, transmission electron microscopy (TEM), and analytical electron microscopy (AEM) are employed to identify the interdiffusion processes during fabrication and service of the devices. During the reflow process of both diode and MOSFET devices, (1) the Ag layer dissolves in the liquid solder; (2) two intermetallics, (Ni,Cu)₃Sn₄ and (Cu,Ni)₆Sn₅, form near the back metal/solder interface; and (3) the Au metallization in the substrate side dissolves in the liquid solder, resulting in precipitation of the (Au,Ni,Cu)Sn₄ intermetallic during solidification. During solid-state aging of both diode and MOSFET solder joints at 125°C and 200°C, the following atomic transport processes occur: (1) interdiffusion of Cu, Ni, and Sn, leading to the growth of a (Ni,Cu)₃Sn₄ layer until the Ni layer is completely consumed; (2) interdiffusion of Au, Cu, Ni, and Sn through the (Ni,Cu)₃Sn₄ layer and unconsumed Ni layer to the Ti layer to form a solid solution; and (3) further interdiffusion of Au, Cu, Ni, and Sn through the (Ni,Cu)₃Sn₄ layer to from an (Au,Ti,Ni,Cu)Sn₄ layer. The growth of the latter layer continues until the entire Ti layer is consumed.     

Aging study on interfacial microstructure and solder-ball shear strength of a wafer-level chip-size package with Au/Ni metallization on a Cu pad

Eutectic solder balls (63Sn-37Pb) joined to Cu pads with an Au/Ni metallization have been widely used in wafer-level chip-size package (WLCSP) technology for providing electrical and mechanical interconnections between components. However, some reliability issues must be addressed regarding the intermetallic compounds (IMCs). The formation of a brittle IMC layer between the solder/Cu pad interface impacts considerably upon the solder-ball shear strength. In addition, it will degrade the long-term operating reliability of the WLCSP. This study investigates, by means of experiments, the growth of the IMC layer under isothermal aging for the eutectic Sn-Pb solder reflowed on a Cu pad with an Au/Ni metallization. Forming the Cu pad with an Au/Ni metallization was achieved by a simple semiconductor-manufacturing process. The effects of the intermetallic layer on solder-ball shear strength were examined for various parameters, including the thickness of the Au layer, solder-ball size, and the diameter of the Cu pad. Experimental results indicate that two IMC layers, Au_0.5Ni_0.5Sn₄ and Ni₃Sn₄, form at the solder/Cu pad interface after aging. The Au_0.5Ni_0.5Sn₄ intermetallic layer dominates the total thickness of the IMC layer and grows with aging time while the solder-ball shear strength decreases after aging. The degradation of the solder-ball shear strength was found to be caused mainly by the formation of the Au_0.5Ni_0.5Sn₄ layer. The experimental results established that a thinner Au layer on Cu pad can effectively control the degradation of solder-ball shear strength, and this is especially true for smaller ball sizes.     

Intermetallic compound formation and morphology evolution in the 95Pb5Sn flip-chip solder joint with Ti/Cu/Ni under bump metallization during reflow soldering

Intermetallic compound formation and morphology evolution in the 95Pb5Sn flip-chip solder joint with the Ti/Cu/Ni under bump metallization (UBM) during 350°C reflow for durations ranging from 50 sec to 1440 min were investigated. A thin intermetallic layer of only 0.4 μm thickness was formed at the 95Pb5Sn/UBM interface after reflow for 5 min. When the reflow was extended to 20 min, the intermetallic layer grew thicker and the phase identification revealed the intermetallic layer comprised two phases, (Ni,Cu)₃Sn₂ and (Ni,Cu)₃Sn₄. The detection of the Cu content in the intermetallic compounds indicated that the Cu atoms had diffused through the Ni layer and took part in the intermetallic compound formation. With increasing reflow time, the (Ni,Cu)₃Sn₄ phase grew at a faster rate than that of the (Ni,Cu)₃Sn₂ phase. Meanwhile, irregular growth of the (Ni,Cu)₃Sn₄ phase was observed and voids formed at the (Ni,Cu)₃Sn₂/Ni interface. After reflow for 60 min, the (Ni,Cu)₃Sn₂ phase disappeared and the (Ni,Cu)₃Sn₄ phase spalled off the NI layer in the form of a continuous layer. The gap between the (Ni,Cu)₃Sn₄ layer and the Ni layer was filled with lead. A possible mechanism for the growth, disappearance, and spalling of the intermetallic compounds at the 95Pb5Sn/UBM interface was proposed.     

Inhibiting the formation of (Au1−xNix)Sn4 and reducing the consumption of Ni metallization in solder joints

The effects of adding a small amount of Cu into eutectic PbSn solder on the interfacial reaction between the solder and the Au/Ni/Cu metallization were studied. Solder balls of two different compositions, 37Pb-63Sn (wt.%) and 36.8Pb-62.7Sn-0.5Cu, were used. The Au layer (1 ± 0.2 μm) and Ni layer (7 ± 1 μm) in the Au/Ni/Cu metallization were deposited by electroplating. After reflow, the solder joints were aged at 160°C for times ranging from 0 h to 2,000 h. For solder joints without Cu added (37Pb-63Sn), a thick layer of (Au_1−xNi_x)Sn₄ was deposited over the Ni₃Sn₄ layer after the aging. This thick layer of (Au_1−xNi_x)Sn₄ can severely weaken the solder joints. However, the addition of 0.5wt.%Cu (36.8Pb-62.7Sn-0.5Cu) completely inhibited the deposition of the (Au_1−xNi_x)Sn₄ layer. Only a layer of (Cu_1-p-qAu_pNi_q)₆Sn₅ formed at the interface of the Cu-doped solder joints. Moreover, it was discovered that the formation of (Cu_1-p-qAu_pNi_q)₆Sn₅ significantly reduced the consumption rate of the Ni layer. This reduction in Ni consumption suggests that a thinner Ni layer can be used in Cu-doped solder joints. Rationalizations for these effects are presented in this paper.     

Gold- and Palladium-Induced Embrittlement Phenomenon in Microbumps with Au/Pd(P)/Ni(P) Metallization Pads

In this study, the microstructural evolution of Sn-3Ag-0.5Cu/Au/Pd(P)/Ni(P) microbumps during isothermal aging was examined by electron probe microanalysis and scanning electron microscopy equipped with electron backscatter diffraction. The Au/Pd(P)/Ni(P) trilayer was deposited on 85-μm (opening diameter) Cu pads with a thickness combination of 0.15?μm/0.2?μm/8?μm. The reaction of the Au/Pd(P) dual layer with the molten solder yielded plenty of AuSn₄ and PdSn₄ grains in the solder matrix after reflow, which has never been observed previously in the literature. At the interface, discontinuous, facet-type Cu₆Sn₅ [or (Cu,Ni)₆Sn₅] nucleated. Interestingly, the Cu₆Sn₅ transformed into layered Ni₃Sn₄ after subsequent aging for 250?h at 180°C. Moreover, the AuSn₄ and PdSn₄ agglomerated with each other and resettled to the region neighboring the interface. This configuration changed significantly when a pronounced corrosion occurred in the as-plated Ni(P) metallization pad. In the corroded Ni(P) case, Cu₆Sn₅ rarely appeared at the interface immediately after reflow, but a large quantity of PdSn₄ formed in the solder region near the corroded Ni(P) layer. AuSn₄ in this case distributed uniformly throughout the entire solder joint. Isothermal aging treatment drove the PdSn₄ and AuSn₄ to deposit onto the corroded Ni(P) surface, where they merged with each other as a dense layer of (Au_0.61Pd_0.30Ni_0.09)Sn₄ (250?h). The formation of the (Au,Pd,Ni)Sn₄ layer over the corroded Ni(P) substrate provided a crack initiation site, deteriorating the mechanical reliability of the solder joint. The results of this study show that appropriate deposition of Au/Pd(P)/Ni(P) is very important for the thermal/mechanical reliability of microbumps.     

Effects of substrate metallization of solder/under-bump metallization interfacial reactions in flip-chip packages during multiple reflow cycles

The effects of various elements of substrate metallization, namely, Au, Ni, and P, on the solder/under-bump metallization (UBM), (Al/Ni(V)/Cu) interfacial reactions in flip-chip packages during multiple reflow processes were systematically investigated. It was found that Au and P had negligible effects on the liquid-solid interfacial reactions. However, Ni in the substrate metallization greatly accelerated the interfacial reactions at chip side and degraded the thermal stability of the UBM through formation of a (Cu,Ni)₆Sn₅ ternary compound at the solder/UBM interface. This phenomenon can be explained in terms of enhanced grain-boundary grooving on (Cu,Ni)₆Sn₅ in the molten solder during the reflow process. This could eventually cause the rapid spalling of an intermetallic compound (IMC) from the solder/UBM interface and early failure of the packages. Our results showed that formation of multicomponent intermetallics, such as (Cu,Ni)₆Sn₅ or (Ni,Cu)₃Sn₄, at the solder/UBM interface is detrimental to the solder-joint reliability.     

Ag/Ni Metallization Bilayer: A Functional Layer for Highly Efficient Polycrystalline SnSe Thermoelectric Modules

The structural and electrical characteristics of Ag/Ni bilayer metallization on polycrystalline thermoelectric SnSe were investigated. Two difficulties with thermoelectric SnSe metallization were identified for Ag and Ni single layers: Sn diffusion into the Ag metallization layer and unexpected cracks in the Ni metallization layer. The proposed Ag/Ni bilayer was prepared by hot-pressing, demonstrating successful metallization on the SnSe surface without interfacial cracks or elemental penetration into the metallization layer. Structural analysis revealed that the Ni layer reacts with SnSe, forming several crystalline phases during metallization that are beneficial for reducing contact resistance. Detailed investigation of the Ni/SnSe interface layer confirms columnar Ni-Sn intermetallic phases [(Ni₃Sn and Ni₃Sn₂) and Ni_5.63SnSe₂] that suppress Sn diffusion into the Ag layer. Electrical specific-contact resistivity (5.32 × 10^?4 Ω cm²) of the Ag/Ni bilayer requires further modification for development of high-efficiency polycrystalline SnSe thermoelectric modules.     

Electroless Ni/Immersion Au interconnects: Investigation of black pad in wire bonds and solder joints

Black Pad was observed on Electroless Ni/Immersion Au (ENIG) wire bond pads. Thick immersion Au on highly corroded electroless Ni was detected. It was determined that the pads were electrically connected to the Cu ground plane due to a Ni bridge formed inside normally open photovias. The mechanism of the bridge formation was verified and preventative actions were taken; it was demonstrated that formation of Black Pad could be switched on and off. The mechanism of Black Pad formation is proposed to be defective ENIG plating involving variation of both the electroless Ni and immersion Au plating processes. The intermetallic structures of solder joints on the above pads were studied. The study was conducted on both defective and non-defective pads to show differences in intermetallic structure and composition. Me₂Sn₄ and Me₂Sn₂ (Me=Cu, Ni, and Au) intermetallics were formed on non-defective pads, which nucleated on the Ni layer and grew inside the molten solder. However, only the Me₃Sn intermetallic was formed on defective pads inside the corroded Ni Layer. Both mechanisms of intermetallic formation were found on pads with mildly corroded Ni and intermediate Au thickness (4.5–7 in).     

Interfacial reactions and shear strengths between Sn-Ag-based Pb-free solder balls and Au/EN/Cu metallization

The morphological and compositional evolutions of intermetallic compounds (IMCs) formed at three Pb-free solder/electroless Ni-P interface were investigated with respect to the solder compositions and reflow times. The three Pb-free solder alloys were Sn3.5Ag, Sn3.5Ag0.75Cu, and Sn3Ag6Bi2In (in wt.%). After reflow reaction, three distinctive layers, Ni₃Sn₄ (or Ni-Cu-Sn for Sn3.5Ag0.75Cu solder), NiSnP, and Ni₃P, were formed on the electroless Ni-P layer in all the solder alloys. For the Sn3.5Ag0.75Cu solder, with increasing reflow time, the interfacial intermetallics switched from (Cu,Ni)₆Sn₅ to (Cu,Ni)₆Sn₅+(Ni,Cu)₃Sn₄, and then to (Ni,Cu)₃Sn₄ IMCs. The degree of IMC spalling for the Sn3.5Ag0.75Cu solder joint was more than that of other solders. In the cases of the Sn3.5Ag and Sn3Ag6Bi2In solder joints, the growth rate of the Ni₃P layer was similar because these two type solder joints had a similar interfacial reaction. On the other hand, for the Sn3.5Ag0.75Cu solder, the thickness of the Ni₃P and Ni-Sn-P layers depended on the degree of IMC spalling. Also, the shear strength showed various characteristics depending on the solder alloys and reflow times. The fractures mainly occurred at the interfaces of Ni₃Sn₄/Ni-Sn-P and solder/Ni₃Sn₄.     

Interfacial Reactions of Sn-58Bi and Sn-9Zn Lead-Free Solders with Au/Ni/SUS304 Multilayer Substrate

The liquid/solid interfacial reactions of Sn-58Bi (SB) and Sn-9Zn (SZ) lead-free solders with Au/Ni/SUS304 multilayer substrates have been investigated in this study. In the SB/Au/Ni/SUS304 couple, only the Ni₃Sn₄ phase with needle-like grains was formed at the SB/Au/Ni/SUS304 interface. The Ni₅Zn₂₁ phase with a column structure was formed at the SZ/Au/Ni/SUS304 interface. The thickness of both intermetallic compounds (IMCs) increased with increasing reaction temperature and time. Meanwhile, the growth mechanism of these two IMCs is seen to follow a parabolic law and is diffusion controlled.     

Effect of Pd Thickness on the Interfacial Reaction and Shear Strength in Solder Joints Between Sn-3.0Ag-0.5Cu Solder and Electroless Nickel/Electroless Palladium/Immersion Gold (ENEPIG) Surface Finish

Intermetallic compound formation at the interface between Sn-3.0Ag-0.5Cu (SAC) solders and electroless nickel/electroless palladium/immersion gold (ENEPIG) surface finish and the mechanical strength of the solder joints were investigated at various Pd thicknesses (0 μm to 0.5 μm). The solder joints were fabricated on the ENEPIG surface finish with SAC solder via reflow soldering under various conditions. The (Cu,Ni)₆Sn₅ phase formed at the SAC/ENEPIG interface after reflow in all samples. When samples were reflowed at 260°C for 5 s, only (Cu,Ni)₆Sn₅ was observed at the solder interfaces in samples with Pd thicknesses of 0.05 μm or less. However, the (Pd,Ni)Sn₄ phase formed on (Cu,Ni)₆Sn₅ when the Pd thickness increased to 0.1 μm or greater. A thick and continuous (Pd,Ni)Sn₄ layer formed over the (Cu,Ni)₆Sn₅ layer, especially when the Pd thickness was 0.3 μm or greater. High-speed ball shear test results showed that the interfacial strengths of the SAC/ENEPIG solder joints decreased under high strain rate due to weak interfacial fracture between (Pd,Ni)Sn₄ and (Cu,Ni)₆Sn₅ interfaces when the Pd thickness was greater than 0.3 μm. In the samples reflowed at 260°C for 20 s, only (Cu,Ni)₆Sn₅ formed at the solder interfaces and the (Pd,Ni)Sn₄ phase was not observed in the solder interfaces, regardless of Pd thickness. The shear strength of the SAC/ENIG solder joints was the lowest of the joints, and the mechanical strength of the SAC/ENEPIG solder joints was enhanced as the Pd thickness increased to 0.1 μm and maintained a nearly constant value when the Pd thickness was greater than 0.1 μm. No adverse effect on the shear strength values was observed due to the interfacial fracture between (Pd,Ni)Sn₄ and (Cu,Ni)₆Sn₅ since the (Pd,Ni)Sn₄ phase was already separated from the (Cu,Ni)₆Sn₅ interface. These results indicate that the interfacial microstructures and mechanical strength of solder joints strongly depend on the Pd thickness and reflow conditions.