Growth and characterization of non-polar ZnO thin films by pulsed laser deposition

Non-polar ZnO thin films were fabricated on r-plane sapphire substrates by pulsed laser deposition at various temperatures from 100 to 500 °C. The effects of the substrate temperature on structural, morphological and optical properties of the films were investigated. Based on the X-ray diffraction analysis, the ZnO thin films grown at 300, 400 and 500 °C exhibited the non-polar (a-plane) orientation and those deposited below 300 °C exhibited polar (c-plane) orientation. In the optical properties of non-polar ZnO films, there were two photoluminescence peaks detected. The peaks (near-band edge emission, blue emission) are due to electron transitions from band-to-band and shallow donor level to valence band, respectively.     

ZnO thin films prepared by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on soda lime glass substrates by pulsed laser deposition (PLD) in an oxygen-reactive atmosphere. The structural, optical, and electrical properties of the as-prepared thin films were studied in dependence of substrate temperature and oxygen pressure. High quality polycrystalline ZnO films with hexagonal wurtzite structure were deposited at substrate temperatures of 100 and 300 °C. The RMS roughness of the deposited oxide films was found to be in the range 2-9 nm and was only slightly dependent on substrate temperature and oxygen pressure. Electrical measurements indicated a decrease of film resistivity with the increase of substrate temperature and the decrease of oxygen pressure. The ZnO films exhibited high transmittance of 90% and their energy band gap and thickness were in the range 3.26-3.30 eV and 256-627 nm, respectively.     

Oxidation of ZnO thin films during pulsed laser deposition process

Pulsed laser deposition of ZnO thin films, using KrF laser, is analysed. The films were deposited on (001) sapphire substrates at 400 °C, at two different oxygen pressures (0·3 and 0·4 mbar) and two different target–substrate distances (30 and 40 mm). It is observed that in order to obtain good quality in the photoluminescence of the films, associated with oxygen stoichiometry, it is needed to maximize the time during which the plasma remains in contact with the growing film (plasma residence time), which is achieved by selecting suitable combinations of oxygen pressures and target to substrate distances. It is also discussed that for the growth parameters used, the higher probability for ZnO films growth results from the oxidation of Zn deposited on the substrate and such process takes place during the time that the plasma is in contact with the substrate. Moreover, it is observed that maximizing the plasma residence time over the growing film reduces the rate of material deposition, favouring the surface diffusion of adatoms, which favours both Zn–O reaction and grain growth.     

Reversible wettability of ZnO nanostructured thin films prepared by pulsed laser deposition

This work reports on the photoinduced wettability changes of high quality nanostructured ZnO films grown on Si by pulsed laser deposition (PLD) under different growth parameters. The wetting behavior of the resulting films can be reversibly switched from hydrophobic to hydrophilic, through alternation of UV illumination and dark storage. The kinetics of this wetting transition are studied by monitoring the time evolution of the corresponding contact angles. Finally, the influence of the film properties over the observed wetting response is discussed.     

Metal-semiconductor transition in Nb-doped ZnO thin films prepared by pulsed laser deposition

The structural, electrical and optical properties of Nb-doped ZnO films were investigated with different Nb contents (0, 0.15, 0.31, 0.46, 0.62, and 0.94 at.%) in this article. The film with 0.46 at.% Nb content showed the lowest resistivity of 8.95 × 10^− 4 Ω cm and high transmittance about 80% with high c-axis orientation. The undoped ZnO film showed a semiconducting behavior. And Nb-doped ZnO films showed a metal-semiconductor transition (MST), which was connected with localization of degenerate electrons. The films showed metallic conductivity at temperatures closer to the ambient temperature and semiconducting behavior at lower temperatures. It was noted that the NZO films with much lower Nb concentration of 0.15 at.% presented MST compared with other transparent conducting oxides films.     

Low-temperature deposition of iridium thin films by pulsed laser deposition

Extremely smooth iridium (Ir) thin films were deposited on Si(1 0 0) substrate at lower temperature than 300 °C by pulsed laser deposition (PLD) technique using Ir target in a vacuum atmosphere. The crystal orientation, surface morphology, and resistivity of the Ir thin films were systematically determined as a function of substrate temperature. Well-crystallized and single-phase Ir thin films with (1 1 1) preferred orientation were obtained at substrate temperature of 200-300 °C. The surface roughness increased with the increasing of substrate temperature. Likewise, the room-temperature resistivity of Ir thin films decreased with increasing substrate temperature, showing a low value of (10.7±0.1) μΩ cm at 300 °C.     

InGaZnO thin films grown by pulsed laser deposition

We fabricated InGaZnO (IGZO) ceramic target (In: Ga: Zn = 1: 1: 4 in atomic ratio) using solid-state reaction at ambient atmosphere, and deposited IGZO thin films on quartz glass at room temperature under various oxygen partial pressures using the pulsed laser deposition method. Influence of oxygen pressure on crystal structure, surface morphology, optical and electrical properties were investigated. It was found that all the films deposited at room temperature exhibit amorphous structure. On the other hand, the physical properties of the films like transparency, electron mobility, and free-electron concentration were found to be correlated to the oxygen pressure during the deposition and in turn to the possible oxygen vacancies or metallic interstitials in the films. The analysis of X-ray photoelectron spectra (XPS) of the films indicated that there are no metallic 3d states of In, Ga and Zn, suggesting that oxygen vacancies could be main defects that affect physical properties of the films.     

Epitaxial aluminum nitride films on sapphire formed by pulsed laser deposition

Highly oriented aluminum nitride thin films were grown on sapphire (0001)-substrate by pulsed laser deposition technique. Characterization was done by X-ray-diffraction, elastic recoil detection analysis and Rutherford backscattering/channeling measurements. The epitaxial properties were studied as function of the substrate temperature and the deposition rate. An epitaxial relation to the sapphire substrate is found to be AlN [0001] || Al₂O₃ [0001] and AlN [11 0] || Al₂O₃ [10 0]. XRD-texture-analysis on films deposited at 850°C shows a full width half maximum Δω of 0.13° (rocking curve) and Δ of 1.1° (in-plane).     

Epitaxial EuO thin films by pulsed laser deposition monitored by in situ x-ray photoelectron spectroscopy

We have grown EuO thin films on silicon [001] and yttrium aluminate [110] from a europium metal target using pulsed laser deposition. In situ x-ray photoelectron spectroscopy has been used to determine the parameter window for stoichiometric EuO deposition. EuO is observed to grow in the relatively high pressure regime of 10⁻⁶-10⁻⁵ mbar, due to the large Eu flux during ablation. EuO is proven to grow epitaxially on yttrium aluminate [110]. Magnetization measurements confirm the stoichiometry of the film.     

ITO thin films deposited by advanced pulsed laser deposition

Indium tin oxide thin films were deposited by computer assisted advanced PLD method in order to obtain transparent, conductive and homogeneous films on a large area. The films were deposited on glass substrates. We studied the influence of the temperature (room temperature (RT)-180 °C), pressure (1-6 × 10^− 2 Torr), laser fluence (1-4 J/cm²) and wavelength (266-355 nm) on the film properties. The deposition rate, roughness, film structure, optical transmission, electrical conductivity measurements were done. We deposited uniform ITO thin films (thickness 100-600 nm, roughness 5-10 nm) between RT and 180 °C on a large area (5 × 5 cm²). The films have electrical resistivity of 8 × 10^− 4 Ω cm at RT, 5 × 10^− 4 Ω cm at 180 °C and an optical transmission in the visible range, around 89%.     

脉冲激光沉积法制备Pt薄膜的研究

采用脉冲激光沉积技术在(0001)取向的蓝宝石基片上外延生长了Pt单晶薄膜,研究了沉积温度和激光能量对Pt薄膜的晶体结构,表面形貌及电学性能的影响规律.X射线衍射(XRD)分析结果表明,在沉积温度650℃、激光脉冲频率1Hz和激光能量280mJ的条件下,制备得到的Pt(111)单晶薄膜,其(111)面ω摇摆曲线半高宽(FWHM)仅为0.068°.原子力显微镜(AFM)分析表明外延的Pt薄膜表面具有原子级平整度,其表面均方根粗糙度(RMS)约为1.776nm.四探针电阻测试结果显示薄膜方阻为1/962Ω/□,满足铁电薄膜的制备工艺对Pt底电极的要求.     

Epitaxial growth of ZnO films on (100) and (001) γ-LiAlO2 substrates by pulsed laser deposition

Structural and optical properties were investigated for ZnO films grown on (100) and (001) γ-LiAlO₂ (LAO) substrates by pulsed laser deposition method. According XRD results, it is intuitionistic that (100) LAO is suitable for fabricating high quality ZnO film, while (001) LAO is unsuitable. The FWHM of XRD, stress in film and FWHM of UV PL spectra for ZnO films on (100) LAO show a decreasing with increasing substrate temperature from 300 to 600 °C. ZnO film fabricated at 600 °C has the greatest grain size, the smallest stress (0.47 Gpa) and PL FWHM value (∼85 meV). This means that the substrate temperature of 600 °C is optimum for ZnO film deposited on (100) LAO. Moreover, it was found that the UV PL spectra intensity of ZnO film is not only related to the grain size and stoichiometric, but also depends on the stress in the film.     

Structural and magnetic properties of Co-Ga co-doped ZnO thin films fabricated by pulsed laser deposition

Co-Ga co-doped ZnO films were fabricated by pulsed laser deposition on quartz substrates. The obtained films exhibited a wurtzite structure with c-axes growth preference. Optical measurements showed the presence of the cobalt ions in a tetrahedral crystal field, which proved that the Co ion substitution in the ZnO lattice, acting as magnetic cation. Hall measurements indicated that the films were n-type conductive with the electron concentrations of ~ 10²⁰/cm³. This value was much higher than that of the Co-doped films, suggesting the effective incorporation of Ga in the films. Room temperature ferromagnetism was observed for the Ga-Co co-doped thin films.     

ZnO thin films grown on platinum (111) buffer layers by pulsed laser deposition

C-axis oriented ZnO layers were grown by pulsed-laser deposition on the surface of a platinum (111) epitaxial thin film supported by a c-sapphire substrate. The Pt bottom layer provides good in-plane lattice matching with c-ZnO, enabling epitaxial re-growth of the latter, as shown by X-ray diffraction data. Room- and low-temperature reflectance and photoluminescence measurements have been performed on such ZnO/Pt heterostructures for the first time. Intense resonances, corresponding to the A and B free excitons, are clearly evidenced in the reflectance measurements at 30 K, while the deconvolved full widths at half maximum of the bound excitonic lines, observed in the photoluminescence spectra at 28 K, range between 3 and 7 meV. This report clearly demonstrates that ZnO epitaxial thin films with very good structural and optical properties can be grown on a Pt bottom electrode and, thus, establishes the potential of this material system for use in ZnO-based optoelectronic devices.     

Al-doped ZnO films by pulsed laser deposition at room temperature

Polycrystalline Al-doped ZnO films with good photoluminescence property were successfully deposited on quartz glass substrates by pulsed laser deposition (PLD) at room temperature. The films were obtained by ablating a metallic target (Zn:Al 3 wt%) at various laser energy densities (1.0-2.1 J/cm²) in oxygen atmosphere (9 Pa). The structure of the films was characterized by XRD. Ultraviolet photoluminescence centered at 359-361 nm was observed in the room temperature PL spectra of the Al-doped ZnO films.     

Epitaxial growth of anatase TiO2 thin films on LaAlO3(100) prepared using pulsed laser deposition

Titanium dioxide thin films were grown on a lattice-matched LaAlO₃(100) surfaces using pulsed laser deposition (PLD) in oxygen atmosphere. The films were characterized using X-ray diffraction (XRD), reflection high-energy electron diffraction (RHEED) and atomic force microscopy (AFM). The crystal structure of all the films was anatase. Preferred oriented films with a c-axis normal to the substrate surface were obtained. RHEED analysis also revealed that the films had the preferential in-plane orientation, demonstrating that anatase films were epitaxially grown on the substrate. The flatness of the films depended on their growth conditions and thickness.     

Production of porous carbon thin films by pulsed laser deposition

Pulsed laser deposition (PLD) has been used together with the Glancing Angle Deposition (GLAD) technique [1 and 2] for the first time to produce highly porous structured films. A laser produced carbon plasma and vapour plume was deposited at a highly oblique incident angle onto rotating Si substrates, resulting in films exhibiting high bulk porosity and controlled columnar microstructure. By varying the substrate rotation rate, the shape of the microcolumns can be tailored. These results extend the versatility of the GLAD process to materials not readily deposited by means of traditional physical vapour deposition techniques.     

Annealing and recrystallization of amorphous ZnO thin films deposited under cryogenic conditions by pulsed laser deposition

This article deals with the annealing of amorphous ZnO thin films prepared by pulsed laser deposition (PLD) under cryogenic conditions. The substrate holder was cooled by liquid nitrogen. X-ray diffraction analysis evidenced that as-deposited films had amorphous structures: analysis by scanning electron microscopy (SEM) revealed their fine grained surface and inner structure. Annealing at temperatures in the range of 200-800 °C resulted in a transition in the thin film crystal structure from amorphous to polycrystalline. Various properties of the ZnO films were found depending on the recrystallization temperature. In depth investigations employing SEM, X-ray diffraction, atomic force microscopy and secondary ion mass spectroscopy provided comparisons of the recrystallizations of undoped ZnO thin films during the phase transition processes from amorphous to hexagonal wurtzite structures.     

Electric properties and surface characterization of transparent Al-doped ZnO thin films prepared by pulsed laser deposition

We grew 2 wt.% Al-doped ZnO (AZO) films on 5.08 cm-diameter polymer substrates at room temperature by the pulsed laser deposition (PLD) technique added the beam-rastering function. The structural properties, surface morphology, resistivity, mobility and chemical bonding states of AZO/polymer films were measured. The structuring of polymer surface by atmospheric plasma can occur at nm scales and can influence adhesion, optical and wettability properties of the materials. With increasing plasma treatment power, surface hydrophilicity and roughness for PET and PES polymer increased, respectively.