Compact circular-patch-based bandpass filter for ultra-wideband wireless communication systems

Ultra-wideband (UWB) is a radio technology that enables low-power-level, short-range, and wide-bandwidth communication, and it has been widely applied in personal area networks, precision geolocation, medical, surveillance, and vehicular radar systems. Since Federal Communications Commission released the unlicensed use of the UWB range (3.1–10.6 GHz), a significant attention has been paid to the development of UWB devices, particularly UWB bandpass filters. In this paper, we propose a novel UWB bandpass filter based on circular patch resonator that is grounded by via and perturbed by slits and defected ground structures. The resonator’s behaviour is analysed in detail and it is shown that its specific configuration allows a flexible control of the three lowest resonant modes, which are used to form UWB passband. To demonstrate the potential of the resonator, a UWB filter has been designed, fabricated, and measured. The filter is characterized by the insertion loss lower than 1 dB and return loss higher than 17 dB within the passband, as well as by very small group delay variation of only 0.07 ns. Also, the filter exhibits suppression higher than 19 dB up to 30 GHz, and very small overall dimensions of only 0.31λ_g × 0.31λ_g, and thus it outperforms other published UWB filters.     

A compact planar ultra-wideband bandpass filter with multiple resonant and defected ground structure

A compact bandpass filter with dumbbell shape Defected Ground Structure (DGS) operating on ultra wide pass band (UWB – 3.1 to 10.6 GHz) is proposed. It is based on hybrid microstrip coplanar waveguide (dual sided metal) structure. A Multiple Resonant Structure (MRS) is constructed using coplanar waveguide (CPW) planar transmission line. The MRS makes the resonance using quarter wavelength and half wavelength open-ended CPW. The equispaced three resonances at lower (3.1 GHz), center (6.85 GHz) and higher edge (10.6 GHz) of the whole Ultra Wide Band is achieved using CPW MRS. To make the band as flat as possible, two more resonances are introduced using quarter wavelength microstrip patches on top of the commonly shared substrate, so the proposed filter becomes a five pole bandpass filter. A dumbbell shaped defected ground structure on either side of CPW MRS improves the return loss almost less than 20 dB over the whole UWB passband. The simulated results of proposed filter show good transmission response within passband and good rejection in out of the band. The simulated and measured results are very close to each other which proves the efficacy of proposed design.     

Miniaturized microstrip bandpass filter designed using rectangular dual spiral resonator

A miniaturized microstrip bandpass filter based on a rectangular dual spiral resonator (DSR) is proposed in this paper. The rectangular DSR bandpass filter is centered at 3.65 GHz to suit for Wireless LAN (IEEE802.11y) application. The proposed filter offers transmission zero at the high side of out-of-band response. Across the bandwidth, the measured minimum insertion loss is about 1.7 dB, while the measured return loss is better than 19 dB. Measurement results are good agreement and closed to the simulated ones. The total circuit size of the miniaturized bandpass filter is about 0.145λ_g by 0.135λ_g, where λ_g is the guided wavelength at 3.65 GHz.     

Compact triple-passband bandpass filter based on new modified stepped impedance resonators

This study proposed a triple-passband bandpass filter with compact size, low loss and high passband selectivity. The filter includes two coupled stepped impedance resonators (SIRs) and two embedded stub-loaded stepped impedance resonators (SL-SIRs), connected with coupling scheme at the symmetric plane of the filter. The filter is designed to have triple-passband at 2.4, 3.5 and 5.2 GHz for worldwide interoperability for microwave access (WiMAX) applications. By properly tuning the impedance ratio and physical length ratio of the SL-SIRs, the three passbands can be easily determined, at the same time, achieving the high passband selectivity and wide stopband. Besides, the transmission zeros near passband edges of each passband are generated by the proposed filter with cross-coupling structure. The measured results are in good agreement with the full-wave electromagnetic (EM) simulation results.     

CPW-Fed UWB antenna with sharp and high rejection multiple notched bands using stub loaded meander line resonator

This paper presents a CPW-fed UWB filter-antenna with sharp and high rejection multiple band notches for band-notched UWB communication applications. The band notch operation is achieved by employing a sharp bandstop filter (BSF) with multiple reject bands using only one element meander line resonator at the bottom layer through theoretical calculations and parametric studies. The adjustment of the notched bands is successfully accomplished by loading the meander line with open ended stubs to modify the harmonic frequencies to the desired bands. The structure of the proposed BSF is simple and compact so that the proposed filter-antenna is achieved with the same size of the reference UWB antenna without an extra area. Measurement results show that the proposed filter-antenna has two notches at the WiMAX systems operating in the 5.8 GHz (5.725–5.85 GHz) and at the international telecommunication union (ITU) operating in the 8.2 GHz (8.025–8.4 GHz). Also, it has sharp rejection characteristics at the edges of the federal communication commission (FCC) band for UWB communications. The experimental measurements are in good agreement with theoretical and simulation results for the BSF and the filter-antenna. Moreover, the filter-antenna exhibits stable omnidirectional radiation patterns except at the notched bands.     

New compact ultra wideband bandpass filter using modified multi-mode resonator

A new compact ultra wideband (UWB) bandpass filter (BPF) using modified multi-mode resonator (MMR) is presented. The filter consists of a multi-mode resonator with dual spur-lines for providing the dual notch bands at 5.2 and 5.8 GHz and connected with a stepped impedance structure for controlling the transmission zeros at lower and higher passband edge. The interdigital coupling input/output (I/O) lines are used for coupling enhancement. The |S₂₁|-magnitude and the frequencies of notch bands can be well determined by tuning the dimensions of the dual spur-lines. The designed procedures are discussed and good agreement between the measurement and EM simulation are compared.     

Asymmetric dual-line coupling strip for multiple notched bands: Theory and implementation

An asymmetric dual-line coupling strip (ADLCS) can provide main two paths for the signals, which make it possible to generate multiple transmission zeroes. The detailed analysis of the ADLCS is proposed in this paper. Based on the microwave network theory, the equivalent circuit of the ADLCS is also developed. Moreover, the structural parameters of ADLCS are studied by calculations and simulations. The center frequencies and bandwidths of the notch bands can be controlled by tuning the structural parameters. Obviously, The ADLCS can be used in the ultra-wideband (UWB) bandpass filter (BPF) to generate multiple notch bands within the passband. To demonstrate the performance of the ADLCS with UWB filter, the structure is applied to the input and output (I/O) of the single-stage UWB Y-shaped BPFs. The proposed UWB Y-shaped BPF has been designed, fabricated, and measured. The measured results agree with the predicted ones closely. The two notch bands of the fabricated UWB Y-shaped BPF centered at 4.5 and 8.1 GHz have 10-dB rejection fractional bandwidths of about 5.6% and 5%, respectively.     

Microstrip dual-band bandpass filter with independently tunable passbands using varactor-tuned stub loaded resonators

In this paper, a dualband bandpass filter with independently tunable passband is proposed. Two half-wavelength resonators with shunt stub have been placed side by side, fed with a common input-output microstrip line to achieve the individual tunability without affecting other passband. For tuning resonance frequency, varactor diodes are used at the ends of the half wavelength resonators and also at the end of the shunt stubs. Proper shunt stub length and width are derived numerically in such a way that only one control voltage is required in each passband. Measured results show that lower passband can be tuned in a frequency range from 1.78 to 1.96 GHz, whereas the upper passband varies from 2.27 to 2.39 GHz individually. H shaped DGS is integrated below the input-output feed lines to suppress higher order harmonics up to 21 GHz with more than 19 dB attenuation.     

Compact UWB Bandpass Filter Using Stub-Loaded Multiple-Mode Resonator

A compact microstrip-line ultra-wideband (UWB) bandpass filter (BPF) using the proposed stub-loaded multiple-mode resonator (MMR) is presented. This MMR is formed by loading three open-ended stubs in shunt to a simple stepped-impedance resonator in center and two symmetrical locations, respectively. By properly adjusting the lengths of these stubs, the first four resonant modes of this MMR can be evenly allocated within the 3.1-to-10.6 GHz UWB band while the fifth resonant frequency is raised above 15.0GHz. It results in the formulation of a novel UWB BPF with compact-size and widened upper-stopband by incorporating this MMR with two interdigital parallel-coupled feed lines. Simulated and measured results are found in good agreement with each other, showing improved UWB bandpass behaviors with the insertion loss lower than 0.8dB, return loss higher than 14.3dB, and maximum group delay variation less than 0.64ns in the realized UWB passband     

Design of microstrip wide stopband quad-band bandpass filters for multi-service communication systems

This paper presents two planar high performance quad-channel bandpass filters, which are designed based on a novel circular multi-mode resonator. In this paper and for the first time, the proposed resonator is utilized to achieve quad passbands. It consists of diverged feeding lines that are coupled to etched circular cells. The first filter has quite close channels at 2.62, 2.88, 4.34 and 4.67 GHz, which make it appropriate for frequency division duplex (FDD) scheme. Meanwhile, the second filter is designed for WCDMA and WiMAX applications. Both filters are able to attenuate the harmonics up to 19 GHz with a maximum harmonic level of −20 dB. The insertion losses and return losses of both filters at all channels are better than 1.2 dB and 17.5 dB, respectively. The harmonic attenuation method is presented employing a LC equivalent circuit of the proposed resonator. In order to verify the designing methodology, the proposed filters are fabricated and measured where there are good agreements between the simulation and measurement results.     

可调微带矩形环带通滤波器

给出了一种可调微带矩形环带通滤波器的仿真和实验结果。在微带矩形环谐振器内加载折线路径,利用PIN管的导通断开状态获得不同的谐振长度,从而实现在2.5GHz和5.2GHz两个频段上带通滤波器的电控切换。PIN管开关正向导通时,在电路中等效于一个电阻,带通滤波器工作的中心频率为5.2GHz,带宽1.2GHz,插入损耗1.08dB;开关断开时,在电路中等效于一个电容,滤波器通带工作频率约为2.5GHz,带宽10MHz,插入损耗为1.99dB。     

Broadband bandpass filters using slotted resonators fed by interdigital coupled lines for improved upper stopband performances

This paper proposes new broadband microstrip bandpass filters based on slotted linear tapered-line resonator (SLTR) and slotted step impedance resonator (SSIR) structures for size reduction and improved stopband performances. A comprehensive treatment of slotted resonators and both ends of the resonator with interdigital coupled lines is described. The design concept is demonstrated by two filter examples including one with an SLTR and another one with an SSIR. These filters have not only compact size but also a wider upper stopband resulting from resonator bandstop characteristics. The simulated and experimental results of stopband performances are better than 15 dB for a frequency range up to 25 GHz.     

一种具有陷波特性的超宽带带通滤波器

采用修改的多模谐振器(MMR)结构,在输入端与输出端开槽形成交叉耦合,实现了一种结构紧凑、频率选择性较高的超宽带(UWB)带通滤波器。修改的多模谐振器能产生5个模式和2个在高低截止频率附近的传输零点,提高了频率选择性。在滤波器的基础上,通过加载谐振器,形成在8.11 GHz处具有陷波特性的超宽带带通滤波器。利用HFSS13.0验证设计原理。仿真结果表明,该超宽带带通滤波器通带为2.61~11.21 GHz,陷波频率为8.11 GHz,能有效抑制X频段(7.91~8.31 GHz)卫星通信系统对超宽带通信系统的影响,适用于超宽带无线通信系统。     

A printed monopole ellipzoidal UWB antenna with four band rejection characteristics

An antenna design with four band rejection characteristics for UWB application is demonstrated. The proposed unique UWB antenna has shape of an embedded ellipse at top of trapezoidal patch (named as ellipzoidal), 50 Ω impedance microstrip line feed and a truncated beveled ground plane. To realize four band stop characteristics, three inverted U-shaped and a single I-shaped slots each of half guided wavelength are utilized on radiating element. The fabricated antenna has dimensions of 27 mm × 36 mm × 1.6 mm. This four band notched ellipzoidal UWB antenna has measured frequency bandwidth 2.8–14 GHz for magnitude of S₁₁ < −10 dB level. The measured ellipzoidal antenna exhibits four band rejection characteristics for magnitude of S₁₁ > −10 dB at 3.55 GHz for WiMAX band (3.26–3.9 GHz), 4.55 GHz for ARN band (4.35–5.05 GHz), 5.7 GHz for WLAN band (5.5–6.65 GHz) and 8.8 GHz for ITU-8 band (7.95–9.35 GHz). The proposed ellipzoidal UWB antenna maintains omnidirectional radiation pattern, gain, linear phase response, <1 ns group delay, and transfer function in the whole UWB operating bandwidth except at notched frequency bands.     

A wideband stepped-impedance rectangular-ring resonator bandpass filter with multiple notched bands

A configuration of wideband bandpass filter (BPF) with multiple notched bands is presented. Proposed BPF is based on stepped-impedance resonator. By utilising dual stepped-impedance resonators in folded topology a rectangular-ring resonator is formed. Two notched bands in the passband are achieved without using asymmetrical coupled lines. In other words, the filter configuration is capable of producing notched bands. It should be noted that additional information on filter performance and design is presented. Measurement results are presented to approve propounded filter characteristics. The measured passband of the second proposed filter is from 3.68 to 10.2 GHz with insertion loss of –1.76 dB in the first passband at the centre frequency of 4.45 GHz. The measured notched band frequencies are about 5.45 and 7.95 GHz with rejection of –21.77 and –20.82 dB, respectively. The return loss in the passband is better than –11.4 dB.     

Compact Ultra-Wideband Bandpass Filter Using Dual-Line Coupling Structure

This letter presents a novel compact ultra-wideband (UWB) microstrip bandpass filter with spurious response suppression. A dual-mode ring resonator is constituted to allocate its first two resonant frequencies in the UWB band, and the dual-line parallel-coupled structure is used in this compact UWB filter, which is expected to achieve much tighter coupling degree. Simulated and measured results are found in good agreement with each other, showing a wide passband from 4.9 to 10.9 GHz, 15 dB return loss bandwidth of about 5 GHz, minimum insertion loss of 0.49 dB at 7.3 GHz, and wide upper stopband with more than 20 dB attenuation up to 20 GHz.     

Design of an integrated UWB antenna with dual band notch characteristics

A miniaturized couple-line-fed planar ultra-wideband (UWB) antenna is proposed, which has a dual band-notched characteristic as well as two integrated monopoles. Narrowband notches are generated at frequencies of 3.5 GHz and 5.5 GHz using independently controlled bent resonators, whereas the monopoles are designed for radiation at 900 MHz and 2.4 GHz. The proposed design is simulated with full wave solvers and verified with measurements. A good agreement is observed between the simulations and measurements for the antenna's return loss, gain and radiation pattern performances.     

Development of tri-band RF filters using evolutionary strategy

This paper is regarding the development of a tri-band bandpass filter based on T-shape resonators for multi-standard wireless networks. The filter dimensions have been optimized by using an evolutionary strategy algorithm in order to obtain three resonance frequencies and two transmission zeros. Our algorithm is a friendly and computational intelligence approach based on biological inspirations from the parents and offsprings relations for multi-object problems. Experiments results and full-wave simulations validate the proposed strategy and demonstrate its efficiency. The filter prototype provides three bands at 0.75, 1.67 and 2.60 GHz with a maximum insertion loss of 0.99 dB.     

Microwave properties and applications of Y–Ba–Cu–O thin films grown on various substrates

Microwave properties of YBa₂Cu₃O_7-δ (YBCO) films grown on (100) LaAlO₃ (LAO), (110) NdGaO₃ (NGO) and (001) SrLaAlO₄ (SLAO) substrates were studied in the form of a microstrip ring resonator at temperatures above 20 K. The YBCO resonator on a SLAO substrate showed microwave properties better than or comparable to other YBCO resonators on LAO substrates. For the YBCO resonators on LAO and SLAO substrates, both Q_U and f₀ appeared to decrease as the temperature was raised. Meanwhile the resonator on a NGO substrate showed different behaviors with Q_U showing a peak at ∼70 K, which are attributed to the unique temperature dependence of the loss tangent of the NGO substrate. An X-band oscillator with a YBCO ring resonator coupled to the circuit was prepared and its properties were investigated at low temperatures. The frequency of the oscillator signal appeared to change from 7.925 GHz at 30 K to 7.878 GHz at 77 K, which was mostly attributed to the change in f₀ of the YBCO ring resonator. The signal power appeared to be more than 4.5 mW at 30 K and 2.1 mW at 77 K, respectively. At 55 K, the frequency of the oscillator signal was 7.917 GHz with the 3 dB-linewidth of 450 Hz.