共查询到20条相似文献,搜索用时 187 毫秒
1.
通过两起典型案例,梳理造成水泥强度检测结果出现较大偏差的诸多因素,提出应对不同试验室水泥强度较大偏差的“一查、二看、三比较、四操作”的四步法,进而对类似问题能够快速查找原因,不同试验室水泥强度偏差较大问题得到及时有效解决。 相似文献
2.
通过两起典型案例,梳理造成水泥强度检测结果出现较大偏差的诸多因素,提出应对不同试验室水泥强度较大偏差的“一查、二看、三比较、四操作”的四步法,进而对类似问题能够快速查找原因,不同试验室水泥强度偏差较大问题得到及时有效解决. 相似文献
3.
测定火山灰质水泥中可溶氧化钙含量控制水泥强度文俊涛湖北省松滋县刘家场水泥厂(434217)如何有效地控制出磨水泥强度,达到缩小水泥强度偏差,提高企业效益的目的,是各生产企业时时探讨的问题。我厂在通过大量的工业性对比试验和数理统计分析之后,于1990年... 相似文献
4.
根据出磨水泥质量指导水泥出厂,策划出水泥出厂质量智能搭配出库系统,调整因个别水泥库下料不顺畅情况引起的出库搭配不均匀,对出厂水泥质量产生的偏差,进行及时调整,实时观察出厂水泥1 d强度及28 d强度预测值,降低出厂水泥质量偏差。 相似文献
5.
0 引言 2001年4月1日起,我国原有GB177—85水泥标准已停止使用,并全面实施GB/T17671—99《水泥胶砂强度检验方法(ISO法)》及六大通用水泥新标准。由于水灰比、灰砂比、标准砂等一系列试验条件的不同,GB法比ISO法强度测定值偏高,而且不同窑型所生产的熟料,其强度偏差不同;不同立窑企业由于工序管理控制不同,配料方案选择上的区别,所生产的熟料产品其强度偏差也 相似文献
6.
采用不同的粉磨工艺和设备对水泥强度、凝结、硬化过程等一系列物理性能影响较大。通过调查发现,本地不少立窑水泥企业用52.5MPa强度等级的熟料,掺少量混合材,只生产32.5MPa强度等级的水泥。是什么原因降低水泥强度?单凭检测细度发现不了问题,在2000~2003年送样对水泥颗粒级配进行检测,发现是由于颗粒级配不合理。以下将对比不同粉磨工艺对水泥颗粒级配及水泥物理性能的影响.其中所用熟料的强度等级均为52.5MPa左右。 相似文献
7.
水泥企业混凝土试验和试验室的建设 总被引:1,自引:0,他引:1
水泥作为混凝土的一种中间产品,其质量的优劣最终要由混凝土验证,混凝土技术发展的要求使水泥企业利用混凝土试验作为质量管理控制的一个重要部分,成为未来水泥行业发展的必然趋势。通过行业技术分析和笔者亲自参与某大型水泥集团混凝土试验室建设过程,探讨了子泥企业进行混凝土试验的必要性,有利条件,存在问题,以及混凝土试验室的作用和本企业混凝土试验室建设的过程。 相似文献
8.
JC/T452-92<泥质量分等原则>和JC/T452-97<通用水泥质量等级>的颁布及实施,都较大幅度的提高了我国水泥的实物质量水平。湖南韶峰水泥集团公司作为1958年建厂,年生产设计能力202万t的大型水泥生产企业,在实施这些新标准的过程中,水泥实物质量得到了显著提高,表1为1992-1997年水泥年度实物强度和优等品率.表2为1992-1997年水泥年度标准偏差。表1数据表明,水泥质量分等标准自1993年实施后,实物质量有较大提高,尤其早期强度提高明显。3d抗压强度1997年比1992年:… 相似文献
9.
0前言准确度是指测量结果与被测物的真值或接受参照值之间的一致程度。《水泥企业化验室管理规程》规定,水泥强度检验结果不同试验室之间的相对误差允许范围为:抗折强度≤9.0%、抗压强度≤7.0%。为使我国水泥强度与国际接轨和更真实地反映水泥的使用强度值,1999年对我国通用水泥强度检验方法进行了重大修订;修订后的GB/T17671-1999标准(以下简称“ISO法”)于2001年4月1日开始正 相似文献
10.
在水泥生料中掺加萤石、石膏复合矿化剂,能够降低能耗,提高水泥质量,国内许多水泥企业应用了这项技术。但是在进行配料计算时,却没有考虑矿化剂所引人的其它组分(除CaF2、SO3外)对生、熟料化学成分和三率值的影响,造成实际生、熟料化学成分、三率值与设计值相比有较大偏差,尤其当萤石、石膏品位较低或掺量较大时,其偏差更为突出。 本文参考有关资料,根据线性代数理论和最小二乘法的概念,用广义逆矩阵法来求解配料方程,充分考虑矿化剂的化学成分对配料计算的影响,用C语言编制的这套DOS应用程序可适用于三至四组分配… 相似文献
11.
水泥基体参数对水泥砂浆干缩性能的影响 总被引:5,自引:0,他引:5
采用干缩实验研究水灰比、灰砂比、水泥细度等水泥基体参数对水泥浆干缩性能的影响。结果表明,水灰比在0.35~0.60时,砂浆的干缩率随水灰比增大而增大;其它条件不变时,砂浆的干缩率随胶砂比增大而明显增大,随水泥细度提高而增大;高标号水泥的干缩率大于低标号水泥,水泥标号相同时,P.II>P.F>P.S;矿渣微粉比粉煤灰更适用于生产高性能水泥和高性能混凝土;减缩剂能明显减小水泥砂浆的干缩率。 相似文献
12.
激发剂对土聚水泥力学性能影响的研究 总被引:3,自引:0,他引:3
在评述国内外现有研究成果的基础上,通过正交设计方法试验研究不同激发剂种类、掺量对土聚水泥力学性能的影响。试验结果表明:水玻璃碱激发剂对土聚水泥抗压强度的影响效果最好,碱激发剂的强激发作用使土聚水泥产生较高的抗压强度;三乙醇胺对土聚水泥抗压强度的较好影响主要表现在早期,三乙醇胺作为混凝土早强剂,虽然对水泥系统的影响明显,但对本系统的影响不显著;聚丙烯酸钠对土聚水泥抗压强度的影响效果不佳,其原因可能是:大分子量的聚丙烯酸钠由于黏度过高,将偏高岭土颗粒包裹,使其无法与碱激发剂接触,影响了碱激发剂的激发效果。 相似文献
13.
基于硫铝酸盐水泥、硅酸盐水泥各自的特点,研究了二者复配后的标准稠度用水量、凝结时间、水化热效应、胶砂强度、膨胀性、水化产物的物相及微观形貌。结果表明,复配水泥的标准稠度用水量因复配比例不同而变化,凝结时间相对于占主导地位的单组分水泥明显缩短;复配水泥的早期水化速率得到提高,1d、7d的水化放热量均低于占主导地位的单组分水泥;28d抗压、抗折强度低于任何单组分水泥;膨胀性的大小取决于两种水泥的复配比例;硫铝酸盐水泥与硅酸盐水泥的复配使二者的水化相互促进,随着硫铝酸盐水泥掺量的增加,Ca(OH)2相的衍射峰减弱,AFt相的衍射峰增强;纯硅酸盐水泥水化后的微观形貌是致密的,而与硫铝酸盐水泥复配后则出现微观裂纹。 相似文献
14.
E. A. M. Gad M. M. A. El-Sukkary W. M. Sayed S. A. Abo-El-Enein 《Journal of chemical technology and biotechnology (Oxford, Oxfordshire : 1986)》1995,62(3):310-316
Various Portland cement pastes were made using water cement ratios of 0·20, 0·25, 0·35 or 0·40 and then cured for 1, 3, 7, 28, 90 or 180 days. These pastes were impregnated with acrylic acid monomer under vacuum and the monomer-impregnated samples were then treated at two different temperatures, 40 or 60°C, for the polymerization process, using benzoyl peroxide as initiator. Several physicochemical studies were carried out on each cement paste; these studies include compressive strength tests, bulk density, compressive strength versus gel/space ratio relationships, polymer load, X-ray diffraction analysis and differential thermal analysis. Results have indicated that compressive strength improvement in acrylic acid-polymer impregnated cement pastes is mainly dependent on initial water/cement ratio, curing time and gel/space ratio. The results of X-ray diffraction analysis and differential thermal analysis indicated that the intrusion of polymer into the cement paste matrix does not affect the phase composition of the Portland cement hydration products. 相似文献
15.
During the mixing of methyl methacrylate bone cement for use in orthopaedic surgery, unpleasant and possibly harmful fumes are emitted. In an attempt to overcome this problem, three samples of bone cement were prepared by two methods. The effect on the duration of curing and the mechanical properties of the cement after curing have been studied. The samples showed to significant variation in strength when prepared by the different routes. The unconventional method of preparing the cement in a polythene sachet is particularly recommended for Simplex bone cement. 相似文献
16.
Marvin Yudenfreund Kaissar M. Hanna Jan Skalny Ivan Older Stephen Brunauer 《Cement and Concrete Research》1972,2(6):731-743
The compressive strengths of low-porosity pastes made from a Type I and a Type II clinker were investigated. Besides the effect of the type of cement, the effects of different grinding aids, surface of the cement, water-cement ratio (0.2 and 0.3), temperature of hydration (5°, 25°, and 50°), and the age of the paste on compressive strength were determined. By and large, the strength results correlated well with degree of hydration and total porosity, but there was definite indication of at least one other factor. The distribution of pore volume in pores different sizes is suggested as a third factor influencing compressive strength. 相似文献
17.
Juan Cosa Lourdes Soriano María Victoria Borrachero Jordi Payá José M. Monzó 《International Journal of Applied Ceramic Technology》2020,17(1):190-196
Alkali-activated cements are widely studied as alternative and sustainable binder in soil stabilization. In this research work, a mold was designed and constructed, which allowed small cubic specimens to be made (40 × 40 × 40 mm3). With the newly designed mold, cubic samples of soil stabilized with portland cement (OPC) and alternative AAC (based on spent fluid catalytic cracking catalyst FCC) were prepared from which compressive strength was obtained. Cylindrical specimens were also prepared using the same binders as in the previous case to obtain their compressive strength. The results obtained in both cases were compared. Greater resistances for cubic samples were achieved. The cubic specimens were selected for being better in terms of standard deviation of compressive strength for AAC stabilized soil. The obtained compressive strength and standard deviation results were compared between the soil specimens stabilized with different stabilizers cured at 7, 14, 28, and 90 days. The method allows small-sized cubic specimens to be prepared. It improves ergonomics. It also facilitates a large number of specimens being obtained with a small amount of sample. Soil stabilized with AAC yielded higher compressive strength after 90 days compared to that with OPC. 相似文献
18.
19.
20.
水泥水化物晶胶比对水泥抗折性能的影响 总被引:1,自引:0,他引:1
通过在水泥中引入晶体源调整水化物晶胶比以提高水泥的抗折性能,测试了引入不同晶体源的水泥胶砂强度及脆性系数,确定用CA调整水泥石的晶胶比较为适宜。测定了不同CA掺量时水泥砂浆膨胀率及强度,对试验结果进行了分析,得出了CA的最佳掺量。 相似文献