FDTD simulation of radiation characteristics of half-volume HEM and TE-mode dielectric resonator antennas

Cylindrical and rectangular dielectric resonator antennas (DRAs) using HEM_11δ, TE_11δ, and TE_01δ mode were examined to see the radiation pattern, impedance, field distribution and resonant frequency that were achieved when the DRAs were bisected through an image plane by a conducting sheet. The resultant half DRAs are smaller in volume and have a more directional radiation pattern. The elevation angle of maximum radiation was lowered in some cases. Finite-difference time-domain simulation techniques were used     

UHF double dielectric resonator filter with linearised tuning range

A UHF double dielectric resonator filter operating in the TE_01δ mode has been constructed with a high Q, wide (14%) and reasonably linear tuning range. This has been achieved by varying the gap between the resonators, and using the influence of the end wall on the movable resonator. The experimental device is readily scaleable to the cellular radio wave bands     

New scattering matrix parameter formulas for transmission modedielectric resonator filter networks

New scattering matrix parameter formulas are presented for the fundamental TE_01δ mode of a cylindrical dielectric resonator, coupled with two parallel microstrip transmission lines     

A low-loss bandpass filter using electrically coupled high-Q TM01δ dielectric rod resonators

For a TM_01δ mode dielectric rod resonator placed coaxially in a TM₀₁ cutoff circular waveguide, characteristics such as the resonant frequency, its temperature coefficient, the unloaded Q, and the other resonances are discussed on the bases of accurate calculations using the mode-matching method. The results show that this resonator compares favorably with a conventional TE_01δ mode dielectric resonator, particularly for realization of a high unloaded Q. Analytical results also verify that interresonator coupling between these two resonators can be expressed equivalently by a capacitively coupled LC resonant circuit. A four-stage Chebyshev filter having a ripple of 0.035 dB and an equiripple bandwidth of 27 MHz at a center frequency of 11.958 GHz was fabricated using these resonators. Its insertion loss is 0.5 dB, which corresponds to an unloaded Q of 17000, and no spurious response appears in the frequency range below 17 GHz     

双/三模基片集成波导和共面波导混合结构滤波器设计

针对微波带通滤波器小型化、高性能的应用需求,提出使用双/三模方形基片集成波导和共面波导混合结构设计带通滤波器.通过改变双模基片集成波导中TE₁₀₂和TE₂₀₁的谐振频率和外部耦合的强弱,可实现具有近似椭圆、非对称和无传输零点响应的双模滤波器;两个相同尺寸的共面波导作为谐振器蚀刻在基片集成波导表面,与TE₁₀₂和TE₂₀₁共同形成一个通带,设计具有多样性响应的四阶滤波器.在具有非对称响应四阶滤波器的基础上,使主模TE₁₀₁频率移动到该通带附近,设计更宽带宽的五阶滤波器.并对设计的滤波器进行加工和测试.测试结果与仿真结果吻合,表明了该混合结构设计高性能滤波器方法的可行性.     

Propagation of infrared radiation in hollow microstructuralcylindrical waveguides

Theoretical and numerical results are presented on the propagation of infrared radiation in TE₀₁-, TM₀₁-, and TE₁₁-like modes in an empty cylindrical, gold-coated waveguide of micron dimensions. Low-loss propagation is possible for the TE₀₁-like mode, whose configuration is similar to that of the TE₀₁ mode in a guide with perfectly conducting walls. Propagation is more lossy for the TM₀₁- and TE₁₁-like modes. While for small guide radii these modes resemble the TM₀₁ and TE₁₁ modes in a guide with perfectly conducting walls, they transform into surface waves as the guide radius is increased, with losses that are independent of guide radius     

Resonant frequency of cylindrical dielectric resonator placed in anMIC environment

An effective dielectric constant technique to determine the resonant frequency of the TE_01δ mode of a cylindrical dielectric resonator placed in a microwave integrated circuit (MIC) environment is discussed. An expression for the dielectric constant ε_eff which makes it possible to obtain results that compare favorably with rigorous methods is given. Experimental results demonstrating the method's validity are also reported. For a given resonant frequency, closed-form expressions for computing the height of the resonator are given     

Compact quasi-periodic and aperiodic TE0n modeconverters in overmoded circular waveguides for use with gyrotrons

Designs of compact quasi-periodic and aperiodic TE_0n-TE _0n-1 circular waveguide converters for use with gyrotrons in an electron cyclotron heating (ECH) system are developed by analytically and numerically solving the coupled-mode differential equations. Quasi-periodic mode transducer designs which convert the TE₀₂ mode to the TE₀₁ mode, and in some cases also include a taper (waveguide radius reduction), are developed. A 60-GHz aperiodic mode converter-taper combines a 6.35-cm-2.779-cm waveguide diameter taper and a TE₀₂-TE₀₁ mode converter. A 140-GHz aperiodic mode converter-taper combines a 6.35-cm-2.779-cm waveguide diameter taper and a TE₀₃-TE₀₂-TE₀₁ mode converter. The resulting designs are highly efficient (conversion efficiencies ⩾99.4%), are shorter, have a broader bandwidth than previous designs, and have a waveguide radius greater than or equal to 1.389 cm over the entire length of the transducer to allow for high-power transmission. Experimental results consistent with theoretical calculations are presented     

Study of TE0 and TM0 modes in dielectricresonators by a finite difference time-domain method coupled with thediscrete Fourier transform

An application of a numerical method of finite differences in the time domain (FDTD) coupled with the discrete Fourier transform is presented to determine the resonant frequencies of the TE₀ and TM₀ modes of axially symmetric dielectric resonators closed in a cavity. The technique is conceptually and computationally simple, and it allows access at once to information on the entire modal spectrum by means of the fast Fourier transform (FFT) applied to the time series. The cylindrical cavity dielectrically loaded at the base and the resonant frequency of the TE_01δ mode are analyzed in two systems: a cylindrical cavity with a cylindrical dielectric resonator of variable radius, and the shielded dielectric resonator on a microstrip substrate. The results obtained are compared with the rigorous (exact) theoretical solutions and with experimental results     

The design of serpentine-mode converters for high-power microwaveapplications

In this paper, we report the design methodology and numerical results for two mode converters that are suitable for high-power microwave applications. Both converters are designed to operate at 11.424 GHz and utilize periodic serpentine structures to convert between modes with different azimuthal-mode indexes. The first converts about 98.5% of an incident linearly polarized TE₁₂ mode to the TE ₀₁ mode when oriented as an H-plane bend, but has just 1% mode conversion to all modes when oriented as an E-plane bend. The second device converts a linearly polarized TE₁₁ mode to a TM ₀₁ mode with over 99.99% effectiveness. The performance of both devices with respect to parametric variations is detailed. Experimental measurements of the radiation patterns from the TE₁₂ -to-TE₀₁-mode converter are consistent with the theoretical predictions     

Propagation of lower-order modes in a radially anisotropiccylindrical waveguide with liquid crystal cladding

The propagation behavior of the four lower-order modes, HE₁₁ , TE₀₁, TM₀₁, and HE₂₁, in a radially anisotropic cylindrical waveguide with liquid crystal cladding is studied both theoretically and experimentally. The cylindrical waveguide is a doubly-clad fiber with an isotropic core and inner cladding and a radially anisotropic outer cladding made of nematic liquid crystal. Theoretically, the propagation and decay constants for the TE₀₁ and TM₀₁ modes are obtained by solving the wave equations exactly, while those for the HE₁₁ and HE ₂₁ modes are derived using perturbation techniques under the weakly guiding approximation. It is predicted that in such a structure the guided TE₀₁ mode can be separated from the leaky HE₁₁, TM₀₁, and HE₂₁ modes. The theoretical results show good agreement with the experimental observations for a 3 cm long fiber cell with a 5 μm inner cladding radius     

Behavior of the first higher-order modes of a circular core opticalfiber whose core cross-section changes into an ellipse

The vector finite element method is used for investigating the behavior of a set of the first higher-order, four-fold degenerate modes (TE₀₁, TM₀₁, and two-fold degenerate HE₂₁ modes) of a circular core optical fiber whose core cross-section changes into an ellipse. It is found that the TE₀₁ mode becomes the first higher-order mode polarized along the minor axis, E ₂₁^y mode, in a dual-mode region. The remaining three modes become, respectively, the first higher-order mode polarized along the major axis, E₂₁^x mode, and the second higher-order modes polarized along the major and minor axes, E₁₂ ^x and E₁₂^y modes, in the order of magnitude of the effective index. It is also found that the effective index of the E₂₁^x mode is smaller than that of the E₂₁^y mode in a small ellipticity region     

A note on the cutoff frequency of TE01 mode in TEM cells

It is shown that due to the similarity of the structures of the TEM cell and the finned waveguide, the closed-form expression for the cutoff frequency of the TE₁₀ mode in the finned waveguides can be used to calculate the cutoff frequency of the TE₀₁ mode in the symmetric TEM cells. The results obtained by the expression given agree with various numerical methods to within 1%. The results calculated by this expression are compared with those obtained by an approximate analytical expression     

A millimeter-wave omnidirectional dielectric rod metallic gratingantenna

A new millimeter-wave omnidirectional dielectric rod metallic grating antenna is investigated theoretically and experimentally, in this paper. The radiation characteristics of the antenna are carefully investigated by a rigorous formulation for the TE₀₁-mode and TM₀₁-mode excitation in the Ka-band frequency range. Based on the analysis, an omnidirectional antenna excited by the TE₀₁ mode is designed and measured. The measured results are compared with theoretical predictions and good agreement is found. Extensive numerical results are given to establish some useful guidelines for the design of the omnidirectional antenna     

Modellization of losses in TE011-mode waveguide bandpassfilters

A mode-matching technique for the analysis of TE₀₁₁ mode waveguide cylindrical bandpass filters including losses is presented. The modes of a lossy radial waveguide are derived and the generalized scattering matrix of the lossy cavity coupled by two rectangular apertures is computed enforcing an impedance boundary condition on the cavity sidewall. Cavity sidewall losses as well as top and bottom wall losses are therefore taken accurately into account. Numerical and experimental results are given for a four cavity filter in Ka band     

Stopband performance improvement of rectangular waveguide filtersusing stepped-impedance resonators

Rectangular waveguide stepped-impedance resonators (SIRs) are analyzed and employed in the design of an X-band filter with center frequency f₀ = 10 GHz and a bandwidth of 100 MHz. An attenuation of 80 dB is held up to 23.1 GHz and, compared to standard uniform-impedance-resonator filters, a reduction in length of 55 % is achieved at the expense of an increased insertion loss from 0.6 to 1.5 dB. The second resonance of the fundamental TE₁₀ mode can be controlled by adjusting the length and impedance ratio of each resonator. A design procedure that takes into account step discontinuities is described and applied to the design of a number of SIR filters. Finally, the presented theory is supported with experimental results     

一种适用于波束扫描的宽带低剖面介质谐振器天线

近年来,为解决传统介质谐振器天线（dielectric resonator antenna, DRA）体积庞大等问题,新颖的低剖面DRA如介质贴片天线和平面介质天线被提出并迅速成为研究热点.然而,现有的低剖面DRA设计要么平面尺寸较大（>0.5λ0×0.5λ0）,要么带宽较窄（<10%）,限制了它们的实际应用.文中提出了一种具有小型化平面尺寸的宽带低剖面DRA.本天线采用介质贴片设计,顶部为高介电常数的介质贴片,中间为低介电常数的介质基板,底部为缝隙馈电结构.缝隙馈电结构可激励起介质贴片谐振器的基模TE111和高次模TE131两种工作模式,这两种模式的场分布在贴片边缘部分存在基模场强较弱而高次模场强较强的显著区别.本设计巧妙地利用了该区域的模式场强区别,通过略微增加贴片边缘部分高度来显著影响高次模谐振频率而轻微影响基模谐振频率,从而将高次模TE131的谐振频率迅速下拉并与基模TE111的谐振频率靠近合并,在不增大介质贴片平面尺寸的前提条件下获得宽带工作效果.本天线的三维尺寸为0.35λ0×0.35λ0×0.08λ0 (λ0为中心频率处的空气中波长),线极化实物案例测试结果表...     

Achievement of pencil-beam radiation from a TM01 modecircular waveguide source

A method employing appropriately placed parallel-metallic plates in the aperture of a TM₀₁ mode circular waveguide source so as to have it produce pencil-beam radiation is described and analyzed. Programmed computations, with experimental verification, are given for the case of a C-Band TM₀₁ source flared out to a conical horn so as to produce moderate (22 dBi) gain. Means of extending the method to achieve higher gains (40 dBi to 60 dBi) and to modify the plate arrangement so as to produce the same effect with a TE₀₁ mode are briefly outlined     

Broadband linearly polarized beat-wave TEm1/TE11 mode converters

Broadband linearly polarized waveguide mode converters have been developed to transform the high-order cylindrical TE_m1 output wave from harmonic gyrotron amplifiers into the more useful TE₁₁ fundamental waveguide mode. The converter's corrugation period is equal to the beat between the two waves and the bandwidth is predicted to be inversely proportional to the number of periods. Four-period TE ₃₁/TE₁₁ and TE₄₁/TE₁₁ converters with an azimuthal perturbation of m_c=4 and m_c =5, respectively, have yielded a peak conversion efficiency of 98% with a bandwidth greater than 3% and a one-period beat-wave converter has been designed to yield 12% bandwidth. However, it has been observed in measurements that the strong coupling in a short converter can lead to a shift of the center-frequency with an accompanying reduction of the efficiency and bandwidth. A two-period TE₄₁/TE₁₁ converter with 5% bandwidth displayed a 5% frequency shift and a conversion efficiency of only 86%     

A composite optical waveguide-based polarimetric interferometer forchemical and biological sensing applications

A new polarimetric interferometer has been developed on the basis of the phase difference between transverse electric (TE)₀ and transverse magnetic (TM)₀ modes in a composite optical waveguide (OWG). The composite OWG consists of a single-mode potassium ion-exchanged planar waveguide overlaid with a high-index thin film that has two tapered ends and supports only the TE₀ mode. Applying tapered velocity coupling theory, we found that the TE₀ and TM₀ modes coexisting in the potassium ion-exchanged layer were separated in the thin film region of the composite OWG: the TE₀ mode was coupled into the thin film while the TM₀ mode was confined in the potassium ion-exchanged layer. Interference occurs between TE- and TM-polarized output components when a single output beam is passed through a 45°-polarized analyzer. The phase difference φ between both orthogonal output components is very sensitive to the superstrate index n_c in the thin film region. Our experimental results indicate that a slight change of Δn_c=3.71×10^-6 results in the phase-difference variation of Δφ=1° for a 5-mm-long TiO ₂/K⁺ composite OWG with a 34-nm-thick TiO₂ film. Such a simple polarimetric interferometer can be applied to chemical or biological sensors by modifying the upper film surface of the composite OWG with a chemically or biologically active substance