Magnetic penetration depth of Tl2Ba2CuO6+δ:Tc～σ0 in the overdoped region

We report transverse-field muon-spin-rotation experiments carried out on Tl₂Ba₂CuO₆₊ . This system spans the whole overdoped regime, andT _c is reduced by excess oxygen doping, which increases the normal-state carrier concentration. In the heavily overdoped regime(0) is found to scale linearly with the superconducting critical temperatureT _c , similar to the behavior previously observed for other cuprates in the underdoped regime. However, for the overdoped region one has to explain the reduction of ₀, thus the increase of the magnetic penetration depth, in spite of an increasing normal-state carrier concentration. We discuss some possible explanations for this behavior.     

The Tc Amplification by “Shape Resonance” in Doped MgB2

We have applied two channels ( and ) superconductivity model to the Al_1–x Mg _x B₂. Using the experimental data, we have calculated the strength of the interchannel pairing due to quantum interference effects, probed by the interband coupling parameter, and the two gaps as a function of the x. While in MgB₂ the quantum interference effects gives an amplification of T _c by factor 1.5 in comparison with the dominant intra band single channel pairing, in AlMgB₄ the amplification is about 100, in comparison with the dominant intra band single channel pairing.     

Residual thermal stresses in the pull-out specimen: A finite element calculation

The residual thermal stress field in the pull-out specimen is calculated in the case of a high properties thermoset system (carbon-bismaleimide). The calculation is performed within the framework of the linear theory of elasticity by means of a finite element method. The specimen is modelled as a three-phase composite (holder-fibre-matrix). The meniscus which forms at the fibre entry is taken into account in order to provide a realistic stress concentration. The latter is far higher than the matrix strength. Evidence that fibre debonding propagates from the fibre end during cooling is then produced.Nomenclature T thermal load - L _e embedded length - r _f fibre radius - _c curvature radius of the meniscus (fibre entry) - r _c radial dimension of the finite element mesh - E _m,E _h matrix and holder moduli - E _A,E _T fibre axial and transverse moduli - _m, _h matrix and holder thermal expansion coefficients - _A, _T fibre axial and transverse thermal expansion coefficients - _rr, , _zz, _rz non-zero components of the residual stress field - _rr ⁱ , ^im , _zz ^im , _rz ⁱ stresses at the interface in the matrix (r=r _f + ) - _rr ⁱ , ^if , _zz ^if , _rz ⁱ stresses at the interface in the fibre (r=r _f–) - _p1 maximum principal stress - _zz ^f mean axial stress over the fibre section - _rupt ^m matrix strength - u _r ,u _z non-zero components of the displacement field     

The tensile strength and ductility of continuous fibre composites

The plastic instability approach has been applied to the tensile behaviour of a continuous fibre composite. It is shown that the combination of two components with different strengths and degrees of work-hardening produces a new material with a new degree of work-hardening, which may be determined by the present analysis. Expressions for the elongation at rupture and the strength of a composite have been obtained and the results of the calculation are compared with some experimental data.List of symbols V _f volume fraction of fibres in composite - , , true strain of fibre, matrix and composite - s true stress - , , nominal stress on fibre, matrix and composite - _*, _*, _* critical stress of fibre, matrix and composite (ultimate tensile strength) - _*, _* critical strain of separate fibre and matrix - _* critical strain of composite - Q external load - A cross-sectional area - A ₀ initial value of area     

Thermal conductivity of argon and argon-neon mixtures at high temperature

The thermal conductivity of neon and argon-neon mixtures is studied in the temperature range 400–1500°K. This is the first recording of such data above 793°K.Notation T_g true temperature drop in gas layer °K - ¯T temperature, °K, Q, effective thermal flux, W - Q_t, Qr thermal flux transmitted by thermal conductivity and radiation, respectively, W - T_sh correction for temperature shift, % - thermal conductivity of gas mixture, W/m·°K - x_i a molar concentration of neon - _i, _i, _ij, _ij potential function parameters for inter molecular interaction of homogeneous and inhomogeneous molecules - slope of exponential repulsion term Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 33, No. 5, pp. 848–856, November, 1977.     

Energy Scales in the High-Tc Superconductor YBa2Cu3O6+x

The optical conductivity sum rule is used to examine the evolution of the spectral weight N() in both the normal and superconducting states of optimally and underdoped YBa₂Cu₃O_6+x along the a axis. Differences in N() above and below T _c allow the strength of the superconducting condensate _s to be determined. In the optimally-doped material, _s is fully formed at energies comparable to the full superconducting gap maximum (0.1 eV), while in the underdoped material the energy scale for convergence is considerably higher (0.6 eV). This difference is discussed in terms of normal-state properties.     

Fracture stress difference of notched polycarbonate between atmospheric pressure and a hydrostatic pressure

Experimental data on fracture stress of polycarbonate (PC) with and without various artificial notches have been obtained at atmospheric pressure and a high hydrostatic pressure (400 MPa). The difference in fracture stress, _F, between both pressures was directly proportional to the intensity of pressure,P, and was inversely proportional to the stress concentration factor of the notch,K _n such that _F following the form of the Kaieda-Oguchi formula, _F. By using the combined stress concentration factor,K _nc, of superposed notch and craze, and by considering the change in elastic modulus due to pressure, the experimental data agreed with the modified Kaieda-Oguchi formula. The stress concentration factor of the craze was calculated by using the Dugdale model.     

Mixed state odd Hall effect in YBa2Cu3O7−δ with unidirectional twins

We have studied the mixed state Hall effect in YBa₂Cu₃O_7– single crystals with unidirectional twins: _xy=f(H). An analysis of the Hall conductivity _xy in free flux flow regime reveals that _xy can be successfully described by two terms which are related to the quasiparticle excitations and the motion of free vortices respectively. We have discovered the strong twin dependence of the Hall conductivity _xy in the pinning (TAFF) regime and detected the sign reverse of the Hall conductivity _xy at changing angle (+45 °–45 °) between current and twin plane that indicated the presence of backflow of vortices. We have observed that _xy tends to - while approaching the melting line. These results provide the evidence of strong planar pinning influence on the Hall conductivity.     

The influence of grain size on the creep of uranium dioxide

The creep of uranium dioxide has been investigated as a function of grain size. At high stresses, when creep is controlled by dislocation movement, grain boundaries exert a strengthening effect and this strengthening is correlated with the Hall-Petch equation. The degree of strengthening diminishes with increases in temperature. At lower stresses, when creep is controlled by mass transport, grain boundaries exert a weakening effect owing to the reduction in diffusion path length as grain size is reduced. In this range behaviour is correlated with the Nabarro-Herring equation with stress replaced by an effective stress _E=–₀ where ₀ is a threshold stress for diffusional creep associated with the limitation of the ability of boundaries to emit and absorb vacancies. ₀ appears to decrease as grain size is increased.     

Effect of magnesium content on the stress exponent and effective stress in the steady state creep of Al-Mg alloys

The stress exponent of steady state creep,n, and the internal ( _i) and effective stresses ( _e) have been determined using the strain transient dip test for a series of polycrystalline Al-Mg alloys creep tested at 300° C and compared with previously published data. The internal or dislocation back stress, _i, varied with applied stress,, but was insensitive to magnesium content of the alloy, being represented by the empirical equation _i=1.084 ^1.802. Such an applied stress dependence of _i can be explained by using an equation for _i of the form _i (dislocation density)^1/2 and published values for the stress dependence of dislocation density. Values of the friction stress, _f, derived using the equation _e/=(1–c) (1– _f/), indicate that _f is not dependent on the magnesium content. A constant value of _f can best be rationalized by postulating that the creep dislocation structure is relatively insensitive to the magnesium content of the alloy.On leave from Engineering Materials Department, University of Windsor, Windsor, Ontario N9B 3P4, Canada.     

Electrical conductivity,thermoelectric power and dielectric constant of NiWO4

The a.c. electrical conductivity ( _ac), thermoelectric power () and dielectric constant () of antiferromagnetic NiWO₄ are presented. _ac and have been measured in the temperature range 300 to 1000 K and in the temperature range 600 to 1000 K. Conductivity data are interpreted in the light of band theory of solids. The compound obeys the exponential law of conductivity = ₀ exp (–W/kT). Activation energy has been estimated as 0.75eV. The conductivity result is summarized in the following equation =2.86 exp (–0.75 eV/kT)^–1 cm^–1 in the intrinsic region. The material is p-type below 660 K and above 950 K, and is n-type between 660 and 950 K.     

The influence of antimony-additions on the creep behaviour of a 25wt% Cr-20wt% Ni austenitic stainless steel

The effect of antimony on the creep behaviour (dislocation creep) of a 25 wt% Cr-20 wt% Ni stainless steel with ~ 0.005 wt% C was studied with a view to assessing the segregation effect. The antimony content of the steel was varied up to 4000 ppm. The test temperature range was 1153 to 1193 K, the stress range, 9.8 to 49.0 MPa, and the grain-size range, 40 to 600m. The steady state creep rate, , decreases with increasing antimony content, especially in the range of intermediate grain sizes (100 to 300m). Stress drop tests were performed in the secondary creep stages and the results indicate that antimony causes dislocations in the substructure to be immobile, probably by segregating to them, reducing the driving stress for creep.Nomenclature _a Creep stress in a constant load creep test without stress-drop - _A Initial applied stress in stress-drop tests - Stress decrement - ( _A-) Applied stress after a stress decrement, - t _i Incubation time after stress drop (by the positive creep) - _C Strain-arrest stress - _i Internal stress - _{s s}-component (= _i- _c) - Steady state creep rate (average value) in a constant load creep test - Strain rate at time,t, in a constant load creep test - New steady state creep rate (average value) after stress drop from _A to ( _A-) - Strain rate at time,t, after stress drop.     

Experimental investigation of the effects of stress rate and stress level on fracture in polystyrene

The effects of stress rate and stress level on fatigue crack propagation in compression-moulded single-edge notched specimens (0.25 mm in thickness) of polystyrene are reported. Values of the stress rate are obtained from the formula = 2v(_max – _max),, wherev is the frequency and _max, _min are the maximum and minimum stresses of the fatigue cycle. Different levels of are achieved by changing the frequency while keeping _max, _min at fixed values. The effect of the stress level is investigated by keeping and _min constant and varying _max andv. The results show that when the kinetic data are plotted as l/t against the energy release rateG ₁, a relatively small effect of the stress rate is observed. If the same data are treated as l/N againstG ₁, a decrease in l/N with test frequency is seen. The increase in the level of _max results in a higher crack speed. The critical crack length is found to be practically the same for all stress-rate experiments. A decrease in the critical crack length is observed with the increase in stress level. Analysis of craze distribution around the crack path shows that the extent of crazing decreases with the increase in stress rate and increases with the increase in stress level. For all experimental conditions, the ratio of the second moment to the square root of the fourth moment of the histograms of craze density along directions normal to the crack path is found to be constant throughout the slow phase of crack propagation. This result supports a self-similarity hypothesis of damage evolution proposed in the crack layer model.     

Methodic error of conversion of analog signals into frequency-modulated pulse signals

Conclusions For an equiprobable distribution of the position of the beginning of interval T_i on the time axis, _m manifests itself as an uncorrelated random error.If the pulse duration is negligible in comparison with the time interval between adjacent pulses, the ME of the error _m is equal to zero for AFC's with uniform or nonuniform pulse sequences.The RMSD of the error _m varies with T_i, assuming a number of extremum values [_m]_max. For the same values of T_i andf, [_mn]_max exceeds [_mu]_max by a factor of not more than 2. If the maximum allowable values of the RMSD of the methodic error _m are assigned on the basis of experimental conditions, the minimum allowable measurement time of the secondary instrument which receives the AFC signal can be found by means of (7) and (11).Translated from Izmeritel'naya Tekhnika, No. 12, pp. 53–55, December, 1972.     

On the measurement and physical meaning of the cleavage fracture stress in steel

Elastic-plastic two-dimensional (2D) and three-dimensional (3D) finite element models (FEM) are used to analyze the stress distributions ahead of notches of four-point bending (4PB) and three-point bending (3PB) specimens with various sizes of a C-Mn steel. By accurately measuring the location of the cleavage initiation sites, the local cleavage fracture stress _f and the macroscopic cleavage fracture stress _F is accurately measured. The _f and _F measured by 2D FEM are higher than that by 3D FEM. _f values are lower than the _F, and the _f values could be predicted by _f=(0.8––1.0)_F. With increasing specimen sizes (W,B and a) and specimen widths (B) and changing loading methods (4PB and 3PB), the fracture load P _f changes considerably, but the _F and _f remain nearly constant. The stable lower boundary _F and _f values could be obtained by using notched specimens with sizes larger than the Griffiths–Owen specimen. The local cleavage fracture stress _f could be accurately used in the analysis of fracture micromechanism, and to characterize intrinsic toughness of steel. The macroscopic cleavage fracture stress _F is suggested to be a potential engineering parameter which can be used to assess fracture toughness of steel and to design engineering structure.     

Crack-tip damaged zones in rubber-toughened amorphous polymers: a micromechanical model

The various stages of crack propagation in rubber-toughened amorphous polymers (onset and arrest, stable and unstable growth) are governed by the rate of energy dissipation in the cracktip damaged zone; hence the relationship between the applied stress intensity factorK ₁ and the damaged zone size is of utmost importance. The size of the crack-tip damaged zone has been related toK ₁ via a parameter which is characteristic of the material in given conditions: this factor is proportional to the threshold stress for damage initiation in a triaxial stress field, and has been denoted by ^*. Theoretical values of ^* have been calculated by means of a micromechanical model involving the derivation of the stresses near the particles and the application of damage initiation criteria. The morphology, average size and volume fraction of the rubbery particles have been taken into account together with the nature of the matrix. The calculated values of ^* have been successfully compared with the experimental ones, for a wide set of high-impact polystyrenes (HIPS) and rubber-toughened poly(methyl methacrylate) (RTPMMA).Nomenclature PS; HIPS polystyrene; high-impact polystyrene - PMMA; RTPMMA poly(methyl methacrylate); rubber-toughened PMMA - MI; CS/H; CS/R particle morphologies (multiple inclusion; hard core - rubber shell; rubber core - rigid shell) - K _r;K _g bulk moduli of rubber and glassy materials - G _r;G _g shear moduli of the same materials - v _p particle volume fraction - L mean centre-to-centre distance between neighbouring particles - B; H; W standard names for the dimensions of the compact tension specimen - R _y size of the crack-tip plastic zone in a homogeneous material - h half thickness of the crack-tip damaged zone - r; polar coordinates around the crack tip (Fig. 1) - r;r _p distance from particle centre; particle radius - p normalized distance from the particle (Equation 5) - K ₁;K _1c;K _1p stress intensity factor; critical values ofK ₁ at the onset of and during crack growth - G _1c plane strain energy release rate - _y yield stress in uniaxial tension - _th macroscopic threshold stress for the onset of local damage initiation in a composite material - ^* characteristic parameter (Equation 3) - ⁰; ₁ ⁰ ; ₂ ⁰ ; ₃ ⁰ applied stress tensor and its three principal stresses - ⁰ uniaxial applied stress - ; ₁; ₂; ₃ local stress tensor and its three principal stresses - A tensor which elements are the ratios of those of over those of ⁰ (Equation 4) - v Poisson's coefficient of the matrix - g triaxiality factor of the crack-tip stress field - _e; _p Mises equivalent stress; dilatational stress (negative pressure) - I ₁;I ₂ invariants of the stress tensor - U ₁;U ₂ material parameters for argon and Hannoosh's craze initiation criterion (Equation 12)     

A Description of MgB2 Superconductivity Including σ–π Bands Coupling

A two-band scheme of the MgB₂ superconductivity has been developed. The pairing channels incorporate -intraband electron–phonon attraction besides the Coulombic repulsion, together with pair transfer between effective - and -bands. Various MgB₂ superconducting characteristics calculated using a plausible parameter set (which is narrower than the amount of considered properties) agree on a quantitative level with the observations.     

Low endurance fatigue in metals and polymers

The fatigue behaviour of commercially pure aluminium and of nylon under sequentially varying strain amplitudes is compared with a damage law of the type suggested by Miner. Aluminium obeys such a law for both cyclic and uniaxial prestrains but the behaviour of nylon is significantly affected by microcracking, which produces a marked effect of loading sequence.Appendix N Number of strain cycles at a given time - N _f Value of N at failure - True tensile stress - True stress range for a strain cycled specimen - _h Value of at half the life of the specimen - True tensile strain - Total true strain range - _p True plastic strain range (= the breadth of the hysteresis loop at = 0) - _d True diametral strain range - E Young's modulus - Linear strain hardening rate when tested at a particular value of _p - D Damage due to cycling - D _p Damage due to prestrain - _p Prestrain. C, K, K₁, , are constants     

Anisotropy in the resistive superconducting transition under magnetic fields in single crystal Pb2Sr2Ho0.5Ca0.5Cu3O8

Anisotropie properties of the single crystal Pb₂Sr₂Ho_0.5Ca_0.5Cu₃O₈ have been investigated by measuring the electrical resistivity in theab-plane _ab (H, ,T), which depends on the angle between theab-plane and the magnetic-field direction, in various constant fieldsH perpendicular to the current direction. All the angle-dependent values of _ab (H, ,T) at a constant temperature are scaled to be on one curve as a function of reduced field. The anisotropic parameter (m _c ^* /m _ab ^* )^1/2 is estimated as 12–13, which is larger than that of YBa₂Cu₃O₇ and much smaller than that of Bi₂Sr₂CaCu₂O₈. It has been concluded that the anisotropy does not always depend on the thickness of the blocking layer but seems to depend on the overlap of the electronic wave functions along thec-axis. Anisotropy in the pinning potential has also been discussed from the resistive tail in the temperature dependence of _ab (H,,T).