零卷吸预跑合对一类反常弹流油膜的影响

在极低速纯滑动的光弹流实验中,采用高粘度聚丁烯润滑剂形成的弹流油膜会在入口区出现凹陷,该反常的入口凹陷与极限剪切应力/界面滑移有关。针对盘纯滑和球纯滑2种不同的运动条件进行了油膜形状的测量,分析了零卷吸预跑合对油膜形状的影响。结果表明,一般地,纯玻璃盘滑动和纯钢球滑动产生的此类反常的油膜形状并不相同;当对弹流接触副采用零卷吸预跑合处理(即钢球和玻璃盘在接触区以大小相同方向相反的速度运动)之后,纯玻璃盘滑动形成的油膜形状有较大变化,油膜厚度增加,入口的楔形斜度下降,此时纯玻璃盘滑动和纯钢球滑动产生的油膜形状差别减小,甚至相同。     

滑动条件下弹流润滑启动过程的实验观察

使用光干涉动态油膜厚度测量系统对不同启动条件下聚丁烯润滑油弹流油膜的形成过程进行了实验观测。结果表明,在纯滑动条件下,由于界面滑移弹流油膜存在反常的入口凹陷;卷吸速度相等时,较大的启动加速度产生较大的界面滑移,诱发较大的入口凹陷;不同的启动加速度,入口区的油膜形状和最小油膜厚度的变化也不相同。     

Occurrence of Wall Slip in Elastohydrodynamic Lubrication Contacts

Preliminary experimental work has been carried out to identify some of the boundary slip phenomena of highly pressurised polybutenes in an elastohydrodynamic lubrication (EHL) conjunction. The movement of the oil is signified using an entrapment that can be readily formed by the impact of a steel ball against a layer of oil on a glass block in an optical EHL test apparatus. The post-impact lateral movement of the entrapment was investigated under the conditions: (i) pure rolling, (ii) pure glass block sliding (steel ball stationary) and (iii) pure ball sliding (glass block stationary). It was observed that under pure rolling the entrapped oil travels within the contact region at the entrainment speed, which is correlated with EHL theory. Under pure glass block sliding conditions, the speed of the entrapped oil core is less than the entrainment speed, and in the extreme cases, this core can be nearly stationary. Under pure ball sliding conditions, the oil core moves at a speed greater than the entrainment speed. The observation indicates that the oil/steel ball interface can sustain higher shear stress than the oil/glass (chromium coated) interface and there is a boundary slip in terms of relative sliding at the latter interface under the experimental conditions. Furthermore, the amount of slip increases with an increase in the pressure. These experiments provide evidence of the existence of wall slippage, which leads to the abnormal EHL film profile characterised with an inlet dimple as reported earlier.     

EHL Performance of the Lubricant With Shear Strength: Part I — Boundary Slippage and Film Failure

This paper analytically investigates the isothermal line contact elastohydrodynamic lubrication of three lubricants with much different shear strengths under the nondimensional operating parameters of w = 2.15e-4 and U = 2.53e-10 applying the lubricant ideal viscoplastic rheological model. The boundary slippage of the low-shear-strength lubricant occurring in the EHL inlet zone was found and results in a much thinner film compared to the classical EHL theory prediction. The film boundary slippage and its growth with the slide/roll ratio variation of tile low-shear\- strength lubricant exhibit special phenomena, which are much different from those of the high-shear-strength lubricant. The easy occurrence of film failure in concentrated contact in the case of high sliding speed, heavy load, large slide/roll ratio, and low-shear-strength lubricant was concluded due to the severe friction heating on the surface conjunction and the lubricant thermal desorption on tile lubricant/surface boundary. The EHL film failure mechanism was further recognized.     

Experimental observation of a dimple-wedge elastohydrodynamic lubricating film

One of the main features of typical elastohydrodynamic lubricating (EHL) contacts is the unique horseshoe film shape, which can be readily observed by using interferometry and quite accurately modelled by the well-established EHL theory. However, an anomalous EHL film, characterized by a wedge shape together with a tiny dimple at the inlet region, is observed under pure sliding conditions with ultra slow speeds of 3–800 μm/s in an optical EHL test rig. The variations of the wedge and the inlet dimple with different sliding speeds and loads are investigated using a series of polybutene oils of high viscosities. It is found that the inclination of the wedge is dependent on sliding speeds, loads and oil viscosities. The dimple always occurs at the inlet. The appearance of an inlet dimple together with a wedge film shape is reported for the first time. The phenomenon can be attributed to a non-Newtonian characteristic of the lubricant: the limiting shear strength. Additionally, the influence of starvation on the film shape is also examined.     

往复运动条件下润滑油膜特性的实验观察

采用多光束干涉技术观察往复运动条件下润滑油膜的滑移及黏弹特性,研究振幅和频率对往复动态润滑弹流油膜的影响。结果表明:往复运动过程中,在特定时刻气穴的出现使油膜厚度逐渐减小,削弱了滑移程度;因润滑油的黏弹性而引起的运动滞后导致了油膜的非对称性;频率增大时,正行程末端时膜厚明显增大,油膜输送速度也随着增大;而负行程末端油膜受气穴的影响膜厚增大较慢;振幅(输入位移)增大时,正行程末端时油膜整体平移,而负行程末端入口凹陷呈现先变明显而后消失的现象。     

Localized Boundary Effect on Elastohydrodynamic Lubricated Film Shape

The study aimed to determine the formation of an adsorption film at elastohydrodynamic lubricated (EHL) contacts and its effects on EHL film shape and friction. Experiments were conducted on an optical EHL test rig with surfaces of different surface energies. A new type of “abnormal” EHL film shape characterized with three dimples in the inlet of the contact was obtained in pure ball sliding experiments with long-chain polybutene. The adsorption layer was inferred to be the main cause for the “tri-dimple” phenomenon. The “tri-dimple” formation was examined. Under a fixed speed, a single inlet dimple gradually broke into three dimples with increasing number of ball rotation, and it happened with slight increase in friction force. Three zones, namely a central and two lateral zones, of the contact were classified and characterized with different levels of influence on the adsorption layer.     

Effect of Surface Velocity Directions on Elastohydrodynamic Film Shape

This article is focused on the effects of the angle between lubricant entrainment velocity and sliding velocity on elastohydrodynamic film thickness distribution. Thin-film colorimetric interferometry was used to evaluate the film thickness distribution in smooth glass–steel contacts to provide basic data on the effects of the slide–roll ratio and the direction of sliding with respect to entrainment velocity. It was observed that as the sliding perpendicular to the entrainment velocity increased, the overall film thickness was reduced and asymmetry of the film profile with respect to the direction of the entrainment velocity increased. The asymmetry of the film profile with respect to the direction of the entrainment velocity increased with the entrainment speed or the overall film thickness. When the speed of the glass disk was larger than that of the steel ball, a dimple was formed even if there was a difference in direction between the entrainment and sliding velocities. A part of the dimple was exhausted from the elastohydrodynamic lubrication (EHL) conjunction as the angle between the entrainment and sliding velocities approached 90°.     

Effect of Sliding Direction on EHL Film Shape Under High Sliding Conditions

It is well known that a sliding speed influences a lubricant film thickness of elastohydrodynamic rolling–sliding contacts significantly. The effect of sliding is described quite well for unidirectional rolling and sliding; however, there are a limited number of papers dealing with sliding in different directions. This study describes how the sliding direction influences elastohydrodynamic film shape under high sliding conditions. An optical ball-on-disc tribometer together with thin-film colorimetric interferometry method is used for a film thickness measurement. The results show that the sliding direction influences lubricant film shape and the effect is connected with dimple phenomena. The temperature–viscosity wedge effect is discussed as a possible mechanism. The results are important for a film thickness prediction under high sliding conditions and provide experimental evidence for an extension of elastohydrodynamic lubrication (EHL) theory.     

离心脱开型超越离合器弹流润滑分析

离心脱开型超越离合器是航空传动系统中的重要部件,具有低速楔合传动、高速离心脱开的特性,使离合器在不同工作模式下接触载荷与转速呈不同的关系,因此需针对不同工况下离心脱开型超越离合器弹流润滑性能进行分析.建立离心脱开型超越离合器弹流润滑模型,采用多重网格分析方法进行数值求解,分析进油温度与速度对超越离合器弹流润滑性能的影响...     

Movement of Entrapped Oil Under Pure Rolling Conditions

This article presents a study on the movement of an oil entrapment (or impact dimple) in a pure rolling elastohydrodynamic lubricated (EHL) contact. The oil entrapment was formed by impacting a steel ball against a lubricated glass disc. The contact was then activated under pure rolling conditions, and the movement of the entrapped oil was visualized by optical interferometry. It was found that during the movement of the dimple within the EHL contact, there exists a critical value for the displacement of dimple core. For the displacement of the dimple core less than the critical value, the dimple moves at the entrainment velocity and the film thickness of dimple core remains almost constant. For displacement beyond the critical value, the dimple slows down and its depth decreases rapidly. The effects of influential factors such as speed, initial dimple depth, load, and initial gap size were theoretically and experimentally investigated.     

Effect of Interfacial Properties on EHL Under Pure Sliding Conditions

This paper presents an experimental study of the effect of boundary slip on the lubricating film shape and friction of an elastohydrodynamic lubrication (EHL) contact under isothermal conditions. Ball and disc pure sliding experiments were carried out with a high viscosity polybutene oil using a conventional optical EHL test rig. The film shape and friction were measured simultaneously. The results obtained from two discs with different coatings were compared. One disc was coated only with Cr, the partially reflective layer, and the other had an extra layer of SiO₂ coating on top. When running under mild conditions of low load and speed, there was no evidence of any boundary slip effect. However, when the load increased, the Cr-coated disc produced lower film thickness and friction than the SiO₂-coated disc. The Cr-coated surface had a larger contact angle, i.e., smaller surface energy, than the SiO₂ surface, which reflects the weak bonding between the molecules of the surface and the lubricant. The study concludes that surfaces with low surface energy promote boundary slip at the EHL contact, leading to a reduction in friction and film thickness.     

Experimental study on lubrication regime variation in point contacts

The change between elastohydrodynamic lubrication (EHL) and hydrodynamic lubrication (HL) under a wide range of entrainment speeds and applied loads was studied using an optical EHL apparatus. A log-log scale linear relationship was demonstrated in the two lubrication regions between the film thickness and the entrainment speed (or load). A transition region can be clearly discerned between these two regions in which the film thickness no longer bears a linear relationship with the entrainment speed (or load). It is shown that a piezoviscous effect can be distinguished in the HL region by the speed exponent or the load exponent, and that relative sliding has a significant influence on the transition region.     

Study of Boundary Slippage Using Movement of a Post-Impact EHL Dimple Under Conditions of Pure Sliding and Zero Entrainment Velocity

A well-recognized phenomenon of typical traction tests of elastohydrodynamic lubrication (EHL) contacts is finite maximum traction at increasing speeds, which led to the postulation that the limiting shear stress of liquid lubricants, a high-pressure rheological property, existed. If slippage occurs at the oil–solid boundary, the limiting traction measured is not necessarily an intrinsic property of the lubricant but rather a function of interfacial properties between the bounding solid surface and the lubricant. A recent report presented experimental evidence of boundary slippage at EHL contacts using a simple methodology based on differences in the speed of oil entrapment and the apparent entrainment. The reported experiments were carried out under pure sliding conditions. The phenomenon may also be explained by internal slippage in the bulk fluid film because of the limiting shear stress of the lubricant. To clarify this, similar experiments were repeated under zero entrainment velocity (ZEV) conditions. Evidence of the highly pressurized lubricant at the center of the oil entrapment sliding against the solid bounding surface was obtained. The purpose of this article is to discuss whether the slippage is attributed to the limiting shear stress of the oil or the critical shear stress of the oil/solid interfaces, and how to differentiate the magnitudes of the critical shear stress of the two bounding surfaces in a conventional optical EHL test rig.     

EHL under cyclic squeeze motion

A time-dependent EHL problem of a ball impacting a plate by a cyclic approach–separation motion has been solved. Previous experimental findings by some of the authors have been numerically confirmed, i.e., the nearly constant central film thickness during the load-sustaining stage, and the linear relationship between this constant film thickness and the frequency in a log–log scale. The numerical results show a constriction in the trace of central film thickness versus time. Similar to the experiments, numerical results give a dimple film shape, which is caused by the high pressure induced within the contact region. However, the present Newtonian model overestimates the central film thickness and the squeezing contact forces. The influences of the frequency, the static contact load, the amplitude and the pressure–viscosity coefficient on the film thickness and the film pressure have also been investigated.     

A Limiting Solution for the Dependence of Film Thickness on Velocity in EHL Contacts with Very Thin Films

In recent years there have been substantial improvements in the capabilities of numerical modeling of elastohydrodynamic lubricant (EHL) films and it is now possible to analyze a very wide range of conditions rather than needing to rely on extrapolation using classical film thickness regression equations such as those of Dowson and Higginson. However, a new controversy has arisen concerning the film thickness-velocity dependence in EHL contacts at very low speeds and high loads, with some predictions showing a film thickness much less than that predicted by the classical equations. The present article applies the well-established limiting analysis, first presented by Grubin-Ertel, to the inlet of the EHL contact. It is shown that when the load is high and the speed is low (and the pressure gradient is very high in the inlet) an accurate resolution of the inlet pressure rise is critical for the determination of the film thickness. Discretization errors of this type might be responsible for discrepancies between the classical equations and some recently published numerical predictions.     

Multilevel solution for thermal elastohydrodynamic lubrication of rolling/sliding circular contacts

A fast multigrid approach is presented for the analysis of thermal elastohydrodynamic lubrication (EHL) under rolling/sliding circular contacts at high loads and high slip ratios with low computing time on a personal computer. This fast solver combines directiteration, multigrid, Newton-Raphson, Gauss-Seidel iteration, and multilevel multi-integration methods into one working environment that can reduce the computational complexity from O(n³ to O(nlnn) for the thermal EHL problem under rolling/sliding circular contacts. Since the couped Reynolds and energy equations are simultaneously solved by the Newton-Raphson scheme, the iteration for the convergence solution is less than those of the classical approach. Results show that thermal effects on the pressure profile and film thickness are significant for a wide range of loads, speeds and slip ratios. The maximum midfilm and surface temperature rise in the Hertzian contact region increases with increasing slip ratio, dimensionless speed, and load. The minimum film thickness decreases with increasing load and slip ratio, and decreasing dimensionless speed.     

椭圆接触弹流润滑油膜形状的实验研究

采用多光束干涉测量技术,在自制光弹流实验机上进行了椭圆接触弹流润滑油膜形状的实验测量,观察了椭圆接触区短轴与卷吸方向之间的夹角θ、速度、施加载荷等对油膜形状的影响。结果表明：夹角θ较小时,油膜厚度整体上更大,接触区较窄,入口区油膜更陡峭;低速时,夹角及载荷基本不影响膜厚;高速、轻载时,夹角θ对膜厚影响更显著;载荷及夹角越大,动压油膜越难建立。     

Power law fluid model incorporated into elastohydrodynamic lubrication theory of line contact

An algorithm is developed for the study of the infinitely long slider bearing in general form, considering the lubricant to be an incompressible power law fluid in isothermal conditions. The earlier works on this topic were considered by taking cavitation boundary conditions when a cylinder moves over a plane lubricated with a power law fluid and in EHL solution in a particular case, viz. pure rolling of a cylinder over an identical cylinder. We have considered a general solution including elastohydrodynamic lubrication (EHL) for different values of power law exponent. Deviation of values of central film thickness for different values of power law exponent from those for Newtonian lubricants are presented. The effects of the power law exponent on the central film thickness, minimum film thickness and load capacity are analysed. The effects of rolling and sliding velocities of contact surfaces are also analysed in terms of an equivalent radius of a cylinder moving over a moving plane. Film shapes and pressure distributions are also calculated numerically and presented graphically for various values of central film thickness considered in this paper. A number of observations obtained here with pseudoplastic nature of lubricants are in good agreement with the experimental results. The theoretical observations suggest the behaviour of common lubricants as pseudoplastic fluids in the cases of slowly moving surfaces and motion under heavy load.     

指数率流体热弹流润滑分析

应用多重网格技术,求得了指数率非牛顿流体线接触热弹流润滑的数值解,分析了油膜压力、厚度和温度等随流变指数、速度参数、滑滚比及载荷参数的变化关系,并与相同工况下的等温解进行了比较。结果表明,随着流变指数的增加,油膜厚度和温度、入口处的当量粘度、最小膜厚、中心膜厚和最大温升均增大,而油膜压力和摩擦因数的变化较小。指数率流体弹流润滑问题的热效应不可忽略;与压缩功项相比,油膜能量方程中的热耗散项对温度的影响最大。同时,无量纲速度参数、滑滚比和载荷参数等均影响热弹流润滑特性。