改善DMCC发动机废气排放质量的研究

为找到全面降低柴油机排放的途径,研究了加装氧化催化转化器对柴油／甲醇组合燃烧（DMCC）发动机排放特性的影响,比较了不同工作模式下各污染物的排放量。试验结果表明,DMCC模式下NOx和碳烟排放下降幅度较大,但HC和CO排放增加较多,微粒比排放量也有所增加。经过氧化催化后,HC和CO得到了较大程度的降低,微粒（PM）经氧化后比原机也有所下降。DMCC经采用催化转化器后,废气质量得到改善,实现了同时降低柴油机的NOx和PM的目的。     

柴油甲醇组合燃烧对机车柴油机排放性能的影响

对一台应用于机车的中速大型柴油机,按照柴油/甲醇组合燃烧(DMCC)的要求,进行了相应的改造,以探究DMCC燃烧模式对其排放性能的影响。结果表明:在800 r/min@9 600 N·m工况下,掺烧甲醇后,NO_x比排放大幅降低,但过分提高甲醇替代率,则NO_x比排放会有所升高;CO₂比排放、燃料费用随甲醇替代率的升高而降低;当量油耗则先随甲醇的替代率提高而升高,随后降低;HC比排放随甲醇替代率提高有所升高。相比于原机,在800 r/min、9 600 N·m、-4° ATDC、35.9%替代率工况, NO_x比排放仅为3.15 g/(kW·h),最大降幅达到56.5%;DMCC模式,640 r/min@6 850 N·m工况下,随着供油提前角的推迟,NO_x、HC比排放降低,排气温度逐渐升高;中等替代率下最低油耗对应的供油提前角推迟,高替代率下供油提前角提前。     

Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experimental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than conventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NO _x and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shortened; the peak values of premixed burning rate, the combustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation. Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NO _x emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(2): 19–23 [译自: 内燃机工程]     

Emission characteristics of a turbocharged diesel engine fueled with gas-to-liquids

Emission characteristics of a turbocharged, intercooled, heavy-duty diesel engine operating on neat gas-to-liquids (GTL) and blends of GTL with conventional diesel were investigated and a comparison was made with those of diesel fuel. The results show that nitrogen oxides (NO _x ), smoke, and particulate matter (PM) emissions can be decreased when operating on GTL and diesel-GTL blends. Engine emissions decrease with an increase of GTL fraction in the blends. Compared with diesel fuel, an engine operating on GTL can reduce NO _x , PM, carbon monoxide (CO), and hydrocarbon (HC) by 23.7%, 27.6%, 16.6% and 12.9% in ECE R49 13-mode procedure, respectively. Engine speed and load have great influences on emissions when operating on diesel-GTL blends and diesel fuel in the turbocharged diesel engine. The study indicates that GTL is a promising alternative fuel for diesel engines to reduce emissions. Translated from Transactions of CSICE, 2006, 24(6): 489–493 [译自: 内燃机学报]     

Effect of Diesel/methanol compound combustion on Diesel engine combustion and emissions

This paper introduces a Diesel/methanol compound combustion system (DMCC) and its application to a naturally aspirated Diesel engine with and without an oxidation catalytic converter. In the DMCC system, there are two combustion modes taking place in the Diesel engine, one is diffusion combustion with Diesel fuel and the other is premixed air/methanol mixture ignited by the Diesel fuel. Experiments were conducted on a four cylinder DI Diesel engine, which had been modified to operate in Diesel/methanol compound combustion. Experiments were conducted at idle and at five engine loads at two levels of engine speeds to compare engine emissions from operating on pure Diesel and on operating with DMCC, with and without the oxidation catalytic converter. The experimental results show that the Diesel engine operating with the DMCC method could simultaneously reduce the soot and NOx emissions but increase the HC and CO emissions compared with the original Diesel engine. However, using the DMCC method coupled with an oxidation catalyst, the CO, HC, NOx and soot emissions could all be reduced.     

推进特性试验下生物乳化柴油对柴油机性能的影响

在柴油机上进行柴油、三种生物乳化柴油(E10、E15和E20)和生物柴油的推进特性试验,就其燃烧特性、动力性、经济性及常规排放特性进行对比。试验结果显示:高转速时,生物乳化柴油的缸内燃烧压力和放热率略低于柴油,缸内燃烧温度有所降低;动力性相比柴油略有下降,仅E10的燃油消耗率比柴油低,B100最高;烟度和NOx排放均有显著降低,且随水和丁醇掺混比例增加而降低; CO和HC排放与柴油基本无差别,整体增加不多。表明:生物乳化柴油作为替代燃料能保证柴油机运行的稳定性,可同时降低柴油机的烟度和NOx排放,具有良好的环境效益和经济效益。     

Influence of injection timing on the exhaust emissions of a dual-fuel CI engine

Environmental concerns and limited amount of petroleum fuels have caused interests in the development of alternative fuels for internal combustion (IC) engines. As an alternative, biodegradable, and renewable fuel, ethanol is receiving increasing attention. Therefore, in this study, influence of injection timing on the exhaust emission of a single cylinder, four stroke, direct injection, naturally aspirated diesel engine has been experimentally investigated using ethanol blended diesel fuel from 0% to 15% with an increment of 5%. The engine has an original injection timing 27° CA BTDC. The tests were performed at five different injection timings (21°, 24°, 27°, 30°, and 33° CA BTDC) by changing the thickness of advance shim. The experimental test results showed that NO_x and CO₂ emissions increased as CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. When compared to the results of original injection timing, at the retarded injection timings (21° and 24° CA BTDC), NO_x and CO₂ emissions increased, and unburned HC and CO emissions decreased for all test conditions. On the other hand, with the advanced injection timings (30° and 33° CA BTDC), HC and CO emissions diminished, and NO_x and CO₂ emissions boosted for all test conditions.     

Effects of octane number on exhaust emissions of a spark ignition engine

This paper deals with the experimental study that aims to examine the effects of octane number of three different fuel oxygenates on exhaust emissions of a typical spark ignition engine. Three commonly used oxygenates, namely methyl tertiary butyl ether (MTBE), methanol, and ethanol, which were blended with a base unleaded fuel in three ratios (10, 15 and 20 vol%), were investigated. The engine emissions of CO, HC, and NO_x were measured under a variety of engine operating conditions using an engine dynamometer set‐up. It is found that generally as the octane number of the fuel increases the CO and HC emissions decrease but the NO_x emission increases for all three blends. Further, for the leaded fuel (RON of 92), as the speed of the engine increases the CO and NO_x emissions decrease but the HC emission decreases. A similar trend was found for MTBE blends also. These emission results are presented in terms of octane number and their effects are discussed in this paper. Copyright © 2002 John Wiley & Sons, Ltd.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

柴油/甲醇组合燃烧增压中冷发动机的甲醛及常规排放特性

为了研究柴油/甲醇组合燃烧(DMCC)方式对发动机排放性能的影响,在增压中冷发动机上采用DMCC方式,对甲醛排放特性进行研究,另外在DMCC模式下对加装氧化催化转换器前后常规排放进行对比.结果表明:在各负荷下,甲醛排放均随着甲醇喷射量的增加而升高;在甲醇喷射量不变的情况下,甲醛排放随着负荷的增加明显降低.增压中冷发动机的NOx和碳烟及微粒排放同时大幅度下降,但HC和CO排放增加较多.加装氧化催化转化器后,HC和CO排放得到了大幅度降低,微粒排放也进一步减少.     

A study on the effect of hydrogen enriched intake air on the characteristics of a diesel engine fueled with ethanol blended diesel

This work aims to replace conventional diesel fuel with low and no carbon fuels like ethanol and hydrogen to reduce the harmful emission that causes environmental degradation. Pursuant to this objective, this study investigated the performance, combustion, and emission characteristics of the diesel engine operated on dual fuel mode by ethanol-diesel blends with H₂ enriched intake air at different engine loads with a constant engine speed of 1500 rpm. The results were compared to sole diesel operation with and without H₂ enrichment. The ethanol/diesel was blended in v/v ratios of 5, 10, and 15% and tested in a diesel engine along with a 9 lpm H₂ flow rate at the intake manifold. The results revealed that 10% ethanol with 9 lpm H₂ combination gives the maximum brake thermal efficiency, which is 1% and 4.8% higher than diesel with and without H₂ enrichment, respectively. The brake specific fuel consumption of the diesel-ethanol blends with H₂ flow increased with increasing ethanol ratio in the blend. When the ethanol ratio increased from 5 to 10%, in-cylinder pressure and heat release rate were increased, whereas HC, CO, and NO_x emissions were decreased. At maximum load, the CO and HC emission of 10% ethanol blend with 9 lpm H₂ case decreased by about 50% and 28.7% compared to sole diesel. However, NO_x emission of the same blend was 11.4% higher than diesel. From the results, the study concludes that 10% ethanol blended diesel with a 9 lpm H₂ flow rate at the intake port is the best dual-fuel mode combination that gives the best engine characteristics with maximum diesel replacement.     

Study of spark ignition engine fueled with methanol/gasoline fuel blends

A 3-cylinder port fuel injection engine was adopted to study engine power, torque, fuel economy, emissions including regulated and non-regulated pollutants and cold start performance with the fuel of low fraction methanol in gasoline. Without any retrofit of the engine, experiments show that the engine power and torque will decrease with the increase fraction of methanol in the fuel blends under wide open throttle (WOT) conditions. However, if spark ignition timing is advanced, the engine power and torque can be improved under WOT operating conditions. Engine thermal efficiency is thus improved in almost all operating conditions. Engine combustion analyses show that the fast burning phase becomes shorter, however, the flame development phase is a little delay.When methanol/gasoline fuel blends being used, the engine emissions of carbon monoxide (CO) and hydrocarbon (HC) decrease, nitrogen oxides (NO_x) changes little prior to three-way catalytic converter (TWC). After TWC, the conversion efficiencies of HC, CO and NO_x are better. The non-regulated emissions, unburned methanol and formaldehyde, increase with the fraction of methanol, engine speed and load, and generally the maximum concentrations are less than 200 ppm. Experimental tests further prove that methanol and formaldehyde can be oxidized effectively by TWC. During the cold start and warming-up process at 5 °C, with methanol addition into gasoline, HC and CO emissions decrease obviously. HC emission reduces more than 50% in the first few seconds (cold start period) and nearly 30% in the following warming-up period, CO reduces nearly 25% when the engine is fueled with M30. Meanwhile, the temperature of exhaust increases, which is good to activate TWC.     

Performance and emission characteristics of QHCCI dimethyl ether engine

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NO _x emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NO _x , HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NO _x emission. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(3): 67–70 [译自: 内燃机工程]     

Effects of a DOC+DPF system on emission characteristics of China Π engineering vehicle diesel engine and influence factors of trapping efficiency of PM for DOC+DPF system

To evaluate the emission characteristics of engineering vehicle diesel engine effectively and find a suitable emission control strategy, the emission characteristics experiment of China ?? engineering vehicle diesel engine was conducted with and without DOC+ DPF. The experiment took high-idling, low-idling, and free-acceleration as testing conditions, and used NanoMet3 particulate analysis system to measure PM mass concentration, number concentration and mean particle size. The gaseous emissions (NOx, NO₂, CO, HC) were analyzed by flue gas analyzer Testo350. The results showed that the PM emission characteristics of engineering vehicle diesel engine improved observably under three different conditions With DOC+ DPF. PM mass emissions reduced by over 85%, and PM number emissions were more than reduce of 90%. The metabolic characteristics of PM mean particle size were sample A < sample B < sample C and high-idling < low-idling < free-acceleration. NOx concentration was not influenced obviously by DOC+ DPF, but NO₂/NOx value increased. Besides, DOC+ DPF made CO emissions decreased by 85% and HC emissions decrement between 50%~80% under different conditions. DOC + DPF could improve the emission characteristics of engineering vehicle diesel engine efficiently, which was easily affected by diesel quality and equipment working hours.     

Study of combustion and emission characteristics of turbocharged diesel engine fuelled with dimethylether

An experimental study of a turbocharged diesel engine operating on dimethyl ether (DME) was conducted. The combustion and emission characteristics of the DME engine were investigated. The results show that the maximum torque and power of DME are greater than those of diesel, particularly at low speeds; the brake specific fuel consumption of DME is lower than that of diesel at low and middle engine speeds, and the injection delay of DME is longer than that of diesel. However, the maximum cylinder pressure, maximum pressure rise rate and combustion noises of the DME engine are lower than those of diesel. The combustion velocity of DME is faster than that of diesel, resulting in a shorter combustion duration of DME. Compared with the diesel engine, NO _x emission of the DME engine is reduced by 41.6% on ESC data. In addition, the DME engine is smoke free at any operating condition. __________ Translated from Transactions of CSICE, 2006, 24(3): 193–199 [译自: 内燃机学报]     

Characteristics and energy distribution of modulated multi-pulse injection modes based diesel HCCI combustion and their effects on engine thermal efficiency and emissions

Cycle fuel energy distribution and combustion characteristics of early in-cylinder diesel homogenous charge compression ignition (HCCI) combustion organized by modulated multi-pulse injection modes are studied by the engine test. It is found that heat loss due to unburned fuel droplets and CO emission can be decreased effectively by injection mode regulation, and thermal efficiency can be potentially increased by 4%–12%. From the analyses of combustion process, it is also found that diesel HCCI combustion is a process with a finite reaction rate and is very sensitive to injection timing and injection mode. At injection timing of −90°CA ATDC, extra low NO_x emissions can be obtained along with high thermal efficiency. __________ Translated from Transactions of CSICE, 2006, 24(6): 385–393 [译自: 内燃机学报]     

Effect of Exhaust Gas Recirculation (EGR) on performance,emissions, deposits and durability of a constant speed compression ignition engine

To meet stringent vehicular exhaust emission norms worldwide, several exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Exhaust Gas Recirculation (EGR) is a pre-treatment technique, which is being used widely to reduce and control the oxides of nitrogen (NO_x) emission from diesel engines. EGR controls the NO_x because it lowers oxygen concentration and flame temperature of the working fluid in the combustion chamber. However, the use of EGR leads to a trade-off in terms of soot emissions. Higher soot generated by EGR leads to long-term usage problems inside the engines such as higher carbon deposits, lubricating oil degradation and enhanced engine wear. Present experimental study has been carried out to investigate the effect of EGR on soot deposits, and wear of vital engine parts, especially piston rings, apart from performance and emissions in a two cylinder, air cooled, constant speed direct injection diesel engine, which is typically used in agricultural farm machinery and decentralized captive power generation. Such engines are normally not operated with EGR. The experiments were carried out to experimentally evaluate the performance and emissions for different EGR rates of the engine. Emissions of hydrocarbons (HC), NO_x, carbon monoxide (CO), exhaust gas temperature, and smoke opacity of the exhaust gas etc. were measured. Performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC) were calculated. Reduction in NO_x and exhaust gas temperature were observed but emissions of particulate matter (PM), HC, and CO were found to have increased with usage of EGR. The engine was operated for 96 h in normal running conditions and the deposits on vital engine parts were assessed. The engine was again operated for 96 h with EGR and similar observations were recorded. Higher carbon deposits were observed on the engine parts operating with EGR. Higher wear of piston rings was also observed for engine operated with EGR.     

Performance and exhaust emission characteristics of a CI engine fueled with Pongamia pinnata methyl ester (PPME) and its blends with diesel

Transport vehicles greatly pollute the environment through emissions such as CO, CO₂, NO_x, SO_x, unburnt or partially burnt HC and particulate emissions. Fossil fuels are the chief contributors to urban air pollution and major source of green house gases (GHGs) and considered to be the prime cause behind the global climate change. Biofuels are renewable, can supplement fossil fuels, reduce GHGs and mitigate their adverse effects on the climate resulting from global warming. This paper presents the results of performance and emission analyses carried out in an unmodified diesel engine fueled with Pongamia pinnata methyl ester (PPME) and its blends with diesel. Engine tests have been conducted to get the comparative measures of brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC) and emissions such as CO, CO₂, HC, NO_x to evaluate the behaviour of PPME and diesel in varying proportions. The results reveal that blends of PPME with diesel up to 40% by volume (B40) provide better engine performance (BSFC and BSEC) and improved emission characteristics.     

Combustion,performance and emissions of a diesel engine with H2, CH4 and H2–CH4 addition

Experiments were conducted to investigate the combustion and emission characteristics of a diesel engine with addition of hydrogen or methane for dual-fuel operation, and mixtures of hydrogen–methane for tri-fuel operation. The in-cylinder pressure and heat release rate change slightly at low to medium loads but increase dramatically at high load owing to the high combustion temperature and high quantity of pilot diesel fuel which contribute to better combustion of the gaseous fuels. The performance of the engine with tri-fuel operation at 30% load improves with the increase of hydrogen fraction in methane and is always higher than that with dual-fuel operations. Compared with ULSD–CH₄ operation, hydrogen addition in methane contributes to a reduction of CO/CO₂/HC emissions without penalty on NO_x emission. Dual-fuel and tri-fuel operations suppress particle emission to the similar extent. All the gaseous fuels reduce the geometry mean diameter and total number concentration of diesel particulate. Tri-fuel operation with 30% hydrogen addition in methane is observed to be the best fuel in reducing particulate and NO_x emissions at 70 and 90% loads.