Low-cycle fatigue behavior of Sn-Ag, Sn-Ag-Cu, and Sn-Ag-Cu-Bi lead-free solders

Low-cycle fatigue (LCF) tests on as-cast Sn-3.5Ag, Sn-3Ag-0.5Cu, Sn-3Ag-0.5Cu-1Bi, and Sn-3Ag-0.5Cu-3Bi solders was carried out using a noncontact strain-controlled system at 20°C with a constant frequency of 0.1 Hz. The addition of Cu does not significantly affect the fatigue life of eutectic Sn-Ag solder. However, the fatigue life was significantly reduced with the addition of Bi. The LCF behavior of all solders followed the Coffin-Manson relationship. The fatigue life of the present solders is dominated by the fracture ductility and can be described by the ductility-modified Coffin-Manson’s relationship. Steps at the boundaries of dendrite phases were the initiation sites for microcracks for Sn-3.5Ag, Sn-3Ag-0.5Cu, and Sn-3Ag-0.5Cu-1Bi solders, while for Sn-3Ag-0.5Cu-3Bi solder, cracks initiated along both the dendrite boundaries and subgrain boundaries in the dendrite phases. The linking of these cracks and the propagation of cracks inside the specimen occurred both transgranularly through eutectic phases and intergranularly along dendrite boundaries or subgrain boundaries.     

Fatigue crack-growth behavior of Sn-Ag-Cu and Sn-Ag-Cu-Bi lead-free solders

Fatigue crack-growth behavior and mechanical properties of Sn-3Ag-0.5Cu, Sn-3Ag-0.5Cu-1Bi, and Sn-3Ag-0.5Cu-3Bi solders have been investigated at room temperature (20°C). The tensile strength and hardness of the solders increased with increasing Bi content. However, the yield strengths of Sn-3Ag-0.5Cu-1Bi and Sn-3Ag-0.5Cu-3Bi solders were nearly similar, but the 3Bi solder exhibited the lowest ductility. Fatigue crack-growth behavior of the solders was dominantly cycle dependent in the range of stress ratios from 0.1–0.7 at a frequency of 10 Hz, except for the Sn-3Ag-0.5Cu solder tested at a stress ratio of 0.7. Mixed intergranular/transgranular crack propagation was observed for the Sn-3Ag-0.5Cu solder tested at the stress ratio of 0.7, indicating the importance of creep in crack growth. The Sn-3Ag-0.5Cu-1Bi and Sn-3Ag-0.5Cu-3Bi solders had higher resistance to time-dependent crack growth, resulting from the strengthening effect of the Bi constituent. It appears that the addition of Bi above a certain concentration is harmful to the mechanical properties of Sn-3Ag-0.5Cu.     

Interfacial reaction between multicomponent lead-free solders and Ag,Cu, Ni,and Pd substrates

The interfacial reaction between two prototype multicomponent lead-free solders, Sn-3.4Ag-1Bi-0.7Cu-4In and Sn-3.4Ag-3Bi-0.7Cu-4In (mass%), and Ag, Cu, Ni, and Pd substrates are studied at 250°C and 150°C. The microstructural characterization of the solder bumps is carried out by scanning electron microscopy (SEM) coupled with energy dispersive x-ray analysis. Ambient temperature, isotropic elastic properties (bulk, shear, and Young’s moduli and Poisson’s ratio) of these solders along with eutectic Sn-Ag, Sn-Bi, and Sn-Zn solders are measured. The isotropic elastic moduli of multicomponent solders are very similar to the eutectic Sn-Ag solder. The measured solubility of the base metal in liquid solders at 250°C agrees very well with the solubility limits reported in assessed Sn-X (X=Ag, Cu, Ni, Pd) phase diagrams. The measured contact angles were generally less than 15° on Cu and Pd substrates, while they were between 25° and 30° on Ag and Ni substrates. The observed intermediate phases in Ag/solder couples were Ag₃Sn after reflow at 250°C and Ag₃Sn and ζ (Ag-Sn) after solid-state aging at 150°C. In Cu/solder and Ni/solder couples, the interfacial phases were Cu₆Sn₅ and (Cu,Ni)₆Sn₅, respectively. In Pd/solder couples, only PdSn₄ after 60-sec reflow, while both PdSn₄ and PdSn₃ after 300-sec reflow, were observed.     

Influence of Lanthanum Additions on the Microstructure and Microhardness of Sn-3.5Ag Solder

This study evaluates the effects of different amounts of lanthanum (La) additions on the microstructure and microhardness of Sn-3.5Ag solders. Sn-3.5Ag-xLa ternary solders were prepared by adding 0 wt.% to 1.0 wt.% La to Sn-3.5Ag alloy. Copper substrates were then dipped in the molten solders and these samples aged at 150°C for up to 625 h. The microstructure and microhardness of the as-solidified solder and the aged solder/copper samples were investigated. The Sn-3.5Ag-xLa solders comprised β-Sn, Ag₃Sn, and LaSn₃ phases, and their microstructure was refined by La additions. As-cast, the addition of La increased the microhardness of the Sn-Ag solder due to the refining effect of Ag₃Sn particles and increased formation of LaSn₃ compounds. As the aging time was increased, the microhardness of the solders decreased and the Ag₃Sn compounds coarsened. However, the coarsening of Ag₃Sn compounds was retarded by La, and the size and amount of LaSn₃ compounds did not change perceptibly with aging time. Therefore, La additions can improve the microhardness and thermal resistance of solder joints.     

Morphology and growth kinetics of intermetallic compounds in solid-state interfacial reaction of electroless Ni-P with Sn-based lead-free solders

A comparative study of solid/solid interfacial reactions of electroless Ni-P (15 at.% P) with lead-free solders, Sn-0.7Cu, Sn-3.5Ag, Sn-3.8Ag-0.7Cu, and pure Sn, was carried out by performing thermal aging at 150°C up to 1000 h. For pure Sn and Sn-3.5Ag solder, three distinctive layers, Ni₃Sn₄, SnNiP, and Ni₃P, were observed in between the solder and electroless Ni-P; while for Sn-0.7Cu and Sn-3.8Ag-0.7Cu solders, two distinctive layers, (CuNi)₆Sn₅ and Ni₃P, were observed. The differences in morphology and growth kinetics of the intermetallic compounds (IMCs) at the interfaces between electroless Ni-P and lead-free solders were investigated, as well as the growth kinetics of the P-enriched layers underneath the interfacial IMC layers. With increasing aging time, the coarsening of interfacial Ni₃Sn₄ IMC grains for pure Sn and Sn-3.5Ag solder was significantly greater than that of the interfacial (CuNi)₆Sn₅ IMC grains for Sn-0.7Cu and Sn-3.8Ag-0.7Cu solders. Furthermore, the Ni content in interfacial (CuNi)₆Sn₅ phase slightly increased during aging. A small addition of Cu (0.7 wt.%) resulted in differences in the type, morphology, and growth kinetics of interfacial IMCs. By comparing the metallurgical aspects and growth kinetics of the interfacial IMCs and the underneath P-enriched layers, the role of initial Cu and Ag in lead-free solders is better understood.     

Effects of mechanical deformation and annealing on the microstructure and hardness of Pb-free solders

The microstructure property relations of several Pb-free solders are investigated to understand the microstructural changes during thermal and mechanical processes of Pb-free solders. The Pb-free solder alloys investigated include pure Sn, Sn-0.7% Cu, Sn-3.5% Ag, and Sn-3.8% Ag-0.7% Cu (in weight percent). To reproduce a typical microstructure observed in solder joints, the cooling rate, ingot size, and reflow conditions of cast alloys were carefully controlled. The cast-alloy pellets are subjected to compressive deformation up to 50% and annealing at 150°C for 48 h. The microstructure of Pb-free solders is evaluated as a function of alloy composition, plastic deformation, and annealing. The changes in mechanical property are measured by a microhardness test. The work hardening in Sn-based alloys is found to increase as the amount of alloying elements and/or deformation increases. The changes in microhardness upon deformation and annealing are correlated with the microstructural changes, such as recrystallization or grain growth, in Pb-free solder alloys.     

Effect of cooling rate on growth of the intermetallic compound and fracture mode of near-eutectic Sn-Ag-Cu/Cu pad: Before and after aging

Several near-eutectic solders of (1) Sn-3.5Ag, (2) Sn-3.0Ag-0.7Cu, (3) Sn-3.0Ag-1.5Cu, (4) Sn-3.7Ag-0.9Cu, and (5) Sn-6.0Ag-0.5Cu (in wt.% unless specified otherwise) were cooled at different rates after reflow soldering on the Cu pad above 250°C for 60 sec. Three different media of cooling were used to control cooling rates: fast water quenching, medium cooling on an aluminum block, and slow cooling in furnace. Both the solder composition and cooling rate after reflow have a significant effect on the intermetallic compound (IMC) thickness (mainly Cu₆Sn₅). Under fixed cooling condition, alloys (1), (3), and (5) revealed larger IMC thicknesses than that of alloys (2) and (4). Slow cooling produced an IMC buildup of thicker than 10 μm, while medium and fast cooling produced a thickness of thinner than 5 μm. The inverse relationship between IMC thickness and shear strength was confirmed. All the fast- and medium-cooled joints revealed a ductile mode (fracture surface was composed of the β-Sn phase), while the slow-cooled joints were fractured in a brittle mode (fracture surface was composed of Cu₆Sn₅ and Cu₃Sn phases). The effect of isothermal aging at 130°C on the growth of the IMC, shear strength, and fracture mode is also reported.     

Investigation of Dissolution Behavior of Metallic Substrates and Intermetallic Compound in Molten Lead-free Solders

This study investigates the dissolution behavior of the metallic substrates Cu and Ag and the intermetallic compound (IMC)-Ag₃Sn in molten Sn, Sn-3.0Ag-0.5Cu, Sn-58Bi and Sn-9Zn (in wt.%) at 300, 270 and 240°C. The dissolution rates of both Cu and Ag in molten solder follow the order Sn > Sn-3.0Ag-0.5Cu >Sn-58Bi > Sn-9Zn. Planar Cu₃Sn and scalloped Cu₆Sn₅ phases in Cu/solders and the scalloped Ag₃Sn phase in Ag/solders are observed at the metallic substrate/solder interface. The dissolution mechanism is controlled by grain boundary diffusion. The planar Cu₅Zn₈ layer formed in the Sn-9Zn/Cu systems. AgZn₃, Ag5Zn₈ and AgZn phases are found in the Sn-9Zn/Ag system and the dissolution mechanism is controlled by lattice diffusion. Massive Ag₃Sn phases dissolved into the solders and formed during solidification processes in the Ag₃Sn/Sn or Sn-3.0Ag-0.5Cu systems. AgZn₃ and Ag₅Zn₈ phases are formed at the Sn-9Zn/Ag₃Sn interface. Zn atoms diffuse through Ag-Zn IMCs to form (Ag, Zn)Sn₄ and Sn-rich regions between Ag₅Zn₈ and Ag₃Sn.     

Contact angle measurements of Sn-Ag and Sn-Cu lead-free solders on copper substrates

In this study, the contact angles of four lead-free solders, namely, Sn-3.5Ag, Sn-3.5Ag-4.8Bi, Sn-3.8Ag-0.7Cu, and Sn-0.7Cu (wt.%), were measured on copper substrates at different temperatures. Measurements were performed using the sessile-drop method. Contact angles ranging from 30° to 40° after wetting under vacuum with no fluxes and between 10° and 30° with rosin mildly activated (RMA) and rosin activated (RA) fluxes were obtained. The Sn-3.5Ag-4.8Bi exhibited the lowest contact angles, indicating improved wettability with the addition of bismuth. For all soldering alloys, lower contact angles were observed using RMA flux. Intermetallics formed at the solder/Cu interface were identified as Cu₆Sn₅ adjacent to the solder and Cu₃Sn adjacent to the copper substrate. The Cu₃Sn intermetallic phase was generally not observed when RMA flux was used. The effect of temperature on contact angle was dependent on the type of flux used.     

Comparative study of wetting behavior and mechanical properties (microhardness) of Sn-Zn and Sn-Pb solders

In this paper the solder balling, wetting, spreading, slumping and microhardness testing of the Sn-Zn based solders have been compared with the Sn-Pb solder. Two types of solders (Sn-9Zn and Sn-8Zn-3Bi) have been investigated along with Sn-37Pb solder for reference. The variation of these tests has been done as a function of reflow temperature from 220-250 °C. Solder balls of these three solder pastes after 15 min heating at 230 °C show no ball formation surrounding the central ball. Spread test shows that above 240 °C Sn-9Zn is very good and can be comparable to Sn-37Pb. The wetting angle of Sn-9Zn (39°) at 250 °C is even lower than the Sn-37Pb solder (41°). In case of Sn-8Zn-3Bi, the wetting angle is very high (77°) at 220 °C, which is unacceptable but it drops down to 48° at 250 °C. Line profiles of slump test show that after preheating at 160 °C, Sn-9Zn behaves similar to Sn-37Pb with better distinction in the finer pitch (120 μm). Microhardness shows two different characteristics for eutectic and non-eutectic solder pastes. Hardness of Sn-37Pb and Sn-9Zn (eutectic) decreases with increasing reflow temperature while the microhardness of Sn-8Zn-3Bi (non-eutectic) increases with increasing reflow temperature. Microstructural characterization at 220 and 250 °C shows grain coarsening in Sn-37Pb and Sn-9Zn solders, which cause the hardness to drop a little. For Sn-8Zn-3Bi, with increasing temperature the amount of hard Bi segregation increases which is the main cause of the rise in hardness. SEM images show the formation of Pb rich islands in Sn-37Pb, formation of Zn rod from spheroids in Sn-9Zn and precipitation of Bi-rich phase in Sn-8Zn-3Bi are the important features that contribute to different hardness nature.     

Effects of Metallic Nanoparticles on Interfacial Intermetallic Compounds in Tin-Based Solders for Microelectronic Packaging

Tin (Sn)-based solders have established themselves as the main alternative to the traditional lead (Pb)-based solders in many applications. However, the reliability of the Sn-based solders continues to be a concern. In order to make Sn-based solders microstructurally more stable and hence more reliable, researchers are showing great interest in investigating the effects of the incorporation of different nanoparticles into them. This paper gives an overview of the influence of metallic nanoparticles on the characteristics of interfacial intermetallic compounds (IMCs) in Sn-based solder joints on copper substrates during reflow and thermal aging. Nanocomposite solders were prepared by mechanically blending nanoparticles of nickel (Ni), cobalt (Co), zinc (Zn), molybdenum (Mo), manganese (Mn) and titanium (Ti) with Sn-3.8Ag-0.7Cu and Sn-3.5Ag solder pastes. The composite solders were then reflowed and their wetting characteristics and interfacial microstructural evolution were investigated. Through the paste mixing route, Ni, Co, Zn and Mo nanoparticles alter the morphology and thickness of the IMCs in beneficial ways for the performance of solder joints. The thickness of Cu₃Sn IMC is decreased with the addition of Ni, Co and Zn nanoparticles. The thickness of total IMC layer is decreased with the addition of Zn and Mo nanoparticles in the solder. The metallic nanoparticles can be divided into two groups. Ni, Co, and Zn nanoparticles undergo reactive dissolution during solder reflow, causing in situ alloying and therefore offering an alternative route of alloy additions to solders. Mo nanoparticles remain intact during reflow and impart their influence as discrete particles. Mechanisms of interactions between different types of metallic nanoparticles and solder are discussed.     

Effect of flux on the wetting characteristics of SnAg, SnCu, SnAgBi, and SnAgCu lead-free solders on copper substrates

The effect of flux on the wetting characteristics of four lead-free solders, Sn-3.5Ag, Sn-0.7Cu, Sn-3.5Ag-4.8Bi, and Sn-3.8Ag-0.7Cu (wt.%), on copper substrates have been studied at 240, 260, and 280°C. The fluxes investigated were rosin (R), mildly activated rosin (RMA), and activated rosin (RA). The wetting tests were conducted using the sessile-drop method. Results showed that fluxes significantly affect the wetting properties of the solders. Contact angles ranging from 10° to 30° for RMA, 20° to 30° for RA, and 35° to 60° for R were obtained. The effect of temperature on contact angle depended on the type of flux used. The contact angle decreased with increasing temperature; however, in some cases the contact angle was independent of temperature. The Sn-3.5Ag-4.8Bi exhibited the lowest contact angles indicating improved wettability with addition of bismuth. The microstructure of the solder/copper interface was analyzed by scanning electron microscopy.     

Effect of Zn Addition on Interfacial Reactions Between Sn-4Ag Solder and Ag Substrates

In this study, the effect of Zn (Zn = 1 wt.%, 3 wt.%, and 7 wt.%) additions to Sn-4Ag solder reacting with Ag substrates was investigated under solid-state and liquid-state conditions. The composition and microstructure of the intermetallic compounds (IMCs) significantly changed due to the introduction of different Zn contents. In the case of Sn-4Ag solder with 1 wt.% Zn, a continuous Ag-Sn IMC layer formed on the Ag substrates; discontinuous Ag-Zn layers and Sn-rich regions formed on the Ag substrates under liquid-state conditions when the Sn-4Ag solders contained 3 wt.% and 7 wt.% Zn. If 3 wt.% Zn was added to Sn-4Ag solder, the Ag-Sn IMC would be transformed into a Ag-Zn IMC with increasing aging time. Rough interfaces between the IMCs and the Ag substrates were observed in Sn-4Ag-7Zn/Ag joints after reflowing at 260°C for 15 min; however, the interfaces between the IMCs and the Ag substrates became smooth for Sn-4Ag-1Zn/Ag and Sn-4Ag-3Zn/Ag joints. The nonparabolic growth mechanism of IMCs was probed in the Sn-4Ag-3Zn/Ag joints during liquid-state reaction, and can be attributed to the detachment of IMCs. On the other hand, the effect of gravity was also taken into account to explain the formation of IMCs at the three different interfaces (bottom, top, and vertical) during the reflow procedure.     

Intermetallic growth kinetics for Sn-Ag, Sn-Cu, and Sn-Ag-Cu lead-free solders on Cu, Ni, and Fe-42Ni substrates

Soldering with the lead-free tin-base alloys requires substantially higher temperatures (∼235–250°C) than those (213–223°C) required for the current tin-lead solders, and the rates for intermetallic compound (IMC) growth and substrate dissolution are known to be significantly greater for these alloys. In this study, the IMC growth kinetics for Sn-3.7Ag, Sn-0.7Cu, and Sn-3.8Ag-0.7Cu solders on Cu substrates and for Sn-3.8Ag-0.7Cu solder with three different substrates (Cu, Ni, and Fe-42Ni) are investigated. For all three solders on Cu, a thick scalloped layer of η phase (Cu₆Sn₅) and a thin layer of ε phase (Cu₃Sn) were observed to form, with the growth of the layers being fastest for the Sn-3.8Ag-0.7Cu alloy and slowest for the Sn-3.7Ag alloy. For the Sn-3.8Ag-0.7Cu solder on Ni, only a relatively uniform thick layer of η phase (Cu,Ni)₆Sn₅ growing faster than that on the Cu substrate was found to form. IMC growth in both cases appears to be controlled by grain-boundary diffusion through the IMC layer. For the Fe-42Ni substrate with the Sn-3.8Ag-0.7Cu, only a very thin layer of (Fe,Ni)Sn₂ was observed to develop.     

Interfacial reaction studies on lead (Pb)-free solder alloys

Recently, the research and development activities for replacing Pb-containing solders with Pb-free solders have been intensified due to both competitive market pressures and environmental issues. As a result of these activities, a few promising candidate solder alloys have been identified, mainly, Sn-based alloys. A key issue affecting the integrity and reliability of solder joints is the interfacial reactions between a molten solder and surface finishes in the solder joint structures. In this paper, a fundamental study of the interfacial reactions between several Pb-free candidate solders and surface finishes commonly used in printed-circuit cards is reported. The Pb-free solders investigated include Sn-3.5 Ag, Sn-3.8 Ag-0.7 Cu, and Sn-3.5 Ag-3.0 Bi. The surface finishes investigated include Cu, Au/Ni(P), Au/Pd/Ni(P), and Au/Ni (electroplated). The reaction kinetics of the dissolution of surface finishes and intermetallic compound growth have been measured as a function of reflow temperature and time. The intermetallic compounds formed during reflow reactions have been identified by SEM with energy dispersive x-ray spectroscopy.     

Comparative study of interfacial reactions of Sn-Ag-Cu and Sn-Ag solders on Cu pads during reflow soldering

The interfacial reaction in soldering is a crucial subject for the solder-joint integrity and reliability in electronic packaging technology. However, electronic industries are moving toward lead-free alloys because of environmental concerns. This drive has highlighted the fact that the industry has not yet arrived at a decision for lead-free solders. Among the lead-free alloys, Sn-3.5Ag and Sn-3.5Ag-0.5Cu are the two potential candidates. Here, detailed microstructural studies were carried out to compare the interfacial reaction of Sn-3.5Ag and Sn-3.5Ag-0.5Cu solder with a ball grid array (BGA) Cu substrate for different reflow times. The Cu dissolution from the substrate was observed for different soldering temperatures ranging from 230°C to 250°C, and the dissolution was found to increase with time and temperature. Dissolution of Cu in the Sn-3.5Ag solder is so fast that, at 240°C, 12 μm of the Cu substrate is fully consumed within 5 min. Much less dissolution is observed for the Sn-3.5Ag-0.5Cu solder. In respect to such high dissolution, there is no significant difference observed in the intermetallic compound (IMC) thickness at the interface for both solder alloys. A simplistic theoretical approach is carried out to find out the amount of Cu₆Sn₅ IMCs in the bulk of the solder by the measurement of the Cu consumption from the substrate and the thickness of the IMCs that form on the interface.     

Properties of ternary Sn-Ag-Bi solder alloys: Part I—Thermal properties and microstructural analysis

Bismuth additions of 1% to 10% were made to the 96.5Sn-3.5Ag (wt.%) alloy in an effort to develop a Sn-Ag-Bi ternary composition. A DSC evaluation of the melting properties of the 91.84Sn-3.33Ag-4.83Bi composition suggested the appearance of metastable, short-range order in the atomic structure as a result of low temperature, thermal aging. More extensive solid-state aging studies on 91.84Sn-3.33Ag-4.83Bi/Cu couples resulted in the growth of an intermetallic compound layer at the solder/substrate interface comprised of Cu₃Sn and the Cu₆Sn₅ sub-layers. The growth kinetics of the total layer thickness (x) as a function of solid-state aging time (t) and temperature (T) were represented by the following expression: $$x - x_o = A t^n \exp ( - Q/RT)$$ where x₀=0.57 × 10^?6 m; A=6.22 × 10^?3 m/sⁿ; n=0.46±0.15; and Q=49±8 kJ/mol. TEM analysis of the 91.84Sn-3.33Ag-4.83Bi composition indicated that solid-solution and precipitation strengthening mechanisms were a likely consequence of the Bi additions. Contact angle measurements, Cu/solder/Cu solder joint shear strength tests, and microhardness evaluations were also performed on the Sn-Ag-Bi alloys; those results are reported in Part II.     

Effect of Ag Content and the Minor Alloying Element Fe on the Mechanical Properties and Microstructural Stability of Sn-Ag-Cu Solder Alloy Under High-Temperature Annealing

This study compares the high-Ag-content Sn-3Ag-0.5Cu with the low- Ag-content Sn-1Ag-0.5Cu solder alloy and the three quaternary solder alloys Sn-1Ag-0.5Cu-0.1Fe, Sn-1Ag-0.5Cu-0.3Fe, and Sn-1Ag-0.5Cu-0.5Fe to understand the beneficial effects of Fe on the microstructural stability, mechanical properties, and thermal behavior of the low-Ag-content Sn-1Ag-0.5Cu solder alloy. The results indicate that the Sn-3Ag-0.5Cu solder alloy possesses small primary β-Sn dendrites and wide interdendritic regions consisting of a large number of fine Ag₃Sn intermetallic compound (IMC) particles. However, the Sn-1Ag-0.5Cu solder alloy possesses large primary β-Sn dendrites and narrow interdendritic regions of sparsely distributed Ag₃Sn IMC particles. The Fe-bearing SAC105 solder alloys possess large primary β-Sn dendrites and narrow interdendritic regions of sparsely distributed Ag₃Sn IMC particles containing a small amount of Fe. Moreover, the addition of Fe leads to the formation of large circular FeSn₂ IMC particles located in the interdendritic regions. On the one hand, tensile tests indicate that the elastic modulus, yield strength, and ultimate tensile strength (UTS) increase with increasing Ag content. On the other hand, increasing the Ag content reduces the total elongation. The addition of Fe decreases the elastic modulus, yield strength, and UTS, while the total elongation is still maintained at the Sn-1Ag-0.5Cu level. The effect of aging on the mechanical behavior was studied. After 720 h and 24 h of aging at 100°C and 180°C, respectively, the Sn-1Ag-0.5Cu solder alloy experienced a large degradation in its mechanical properties after both of the aging conditions, whereas the mechanical properties of the Sn-3Ag-0.5Cu solder alloy degraded more dramatically after 24 h of aging at 180°C. However, the Fe-bearing SAC105 solder alloys exhibited only slight changes in their mechanical properties after both aging procedures. The inclusion of Fe in the Ag₃Sn IMC particles suppresses their IMC coarsening, which stabilizes the mechanical properties of the Fe-bearing SAC105 solder alloys after aging. The results from differential scanning calorimetry (DSC) tests indicate that the addition of Fe has a negligible effect on the melting behavior. However, the addition of Fe significantly reduces the solidification onset temperature and consequently increases the degree of undercooling. In addition, fracture surface analysis indicates that the addition of Fe to the Sn-1Ag-0.5Cu alloy does not affect the mode of fracture, and all tested alloys exhibited large ductile dimples on the fracture surface.     

Microstructure and Creep Deformation of Sn-Ag-Cu-Bi/Cu Solder Joints

Sn-Ag-Cu solder is one of the candidate alternatives to Sn-Pb-based solders. In order to improve its performance, different materials have been added to Sn-Ag-Cu-based solders. Several studies on Sn-Ag-Cu-based solders with Bi additions have shown Sn-Ag-Cu-Bi to be a class of solders with good wetting behavior and good performance that show great promise for use in the electronics assembly and packaging industry. To investigate the mechanical reliability of the Sn-Ag-Cu-Bi solders further, single-lap shear creep characteristics have been studied in this work. Dog-bone-type solder joint specimens were formed using five types of solder alloys, Sn-3.0Ag-0.5Cu and Sn-3.0 Ag-0.5Cu-xBi (x = 1 wt.% to 4 wt.%) with Cu substrates, and creep tests were performed at temperatures of 120°C and 150°C under stresses of 5 MPa to 10 MPa. Results indicate that the rupture times for Sn-3.0Ag-0.5Cu-xBi solder joints up to 4 wt.% of Bi are longer than the rupture time for Sn-3.0Ag-0.5Cu. Stress exponents ranged from 3 to 7 for temperatures of 150°C and 120°C with stresses under 10 MPa. Microstructural analyses using scanning electron microscopy (SEM) were performed and related to the creep behavior of the solder joints.     

Effect of Bi on the Interfacial Reaction between Sn-3.7Ag-xBi Solders and Cu

It was reported in previous studies that the addition of Bi could improve the wettability and reduce the melting temperature of Sn-Ag solders. This work investigates the effect of Bi on the interfacial reaction between Sn-Ag-xBi solders and the Cu substrate reflowed at 250°C for different times and thermally aged at 150°C for different durations. Five types of Sn-Ag-based solders, Sn-3.7Ag-xBi (x = 0 wt.% to 4 wt.%), were used in this study. The microstructure of the interfacial Cu-Sn intermetallic compound (IMC) layers between the solders and the Cu substrate was studied, and the thickness of the Cu-Sn IMCs in different solder/Cu systems has been measured. It was found that the thickness of the Cu-Sn IMC layer decreased with increasing amount of Bi in both the reflow and thermally aged condition. The effect of Bi addition on the interfacial reaction between the solder and the Cu substrate was discussed based on the experimental results.